F1T1 THRU F1T7 1.0 AMP. Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Ampere TS-1 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Axial leads, solderable per MILSTD-202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260℃/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension Weight: 0.20 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol F1T1 F1T2 Type Number Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3 ) Operating Temperature Range Storage Temperature Range F1T3 200 140 200 F1T4 400 280 400 F1T5 600 420 600 F1T6 800 560 800 F1T7 Units 1000 V 700 V 1000 V I(AV) 1.0 A IFSM 30 A VF 1.2 V IR 5.0 100 uA uA nS pF O C/W ℃ ℃ Trr Cj RθJA TJ TSTG 150 250 10 100 -65 to +150 -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. - 392 - 500 RATINGS AND CHARACTERISTIC CURVES (F1T1 THRU F1T7) FIG.1- MAXIMUM TYPICAL FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 1.0 0.75 0.5 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 0.25 0 0 25 50 75 100 125 150 40 30 8.3ms Single Half Sine Wave JEDEC Method 20 10 0 175 1 2 4 6 8 10 20 40 60 80 100 o AMBIENT TEMPERATURE. ( C) NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE FIG.3- TYPICAL FORWARD CHARACTERISTICS 20 90 3 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 10 Tj=25oC Pulse Width=300 s 1% Duty Cycle 1 50 30 20 Tj=25 0C 10 0.3 1 0.1 1 2 4 6 10 20 REVERSE VOLTAGE. (V) 0.03 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) FIG.5- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms - 393 - -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm 40 60 100