TI1 CDCVF2509PW 3.3-v phase-lock loop clock driver Datasheet

NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
www.ti.com
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
3.3-V PHASE-LOCK LOOP CLOCK DRIVER
Check for Samples: CDCVF2509
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
•
Use CDCVF2509A (SCAS765) as a
Replacement for This Device
Designed to Meet and Exceed PC133
SDRAM Registered DIMM Specification
Rev. 1.1
Spread Spectrum Clock Compatible
Operating Frequency 50 MHz to 175 MHz
Static Phase Error Distribution at 66 MHz to
166 MHz Is ±125 ps
Jitter (cyc - cyc) at 66 MHz to 166 MHz Is
Typ = 70 ps
Advanced Deep Submicron Process
Results in More Than 40% Lower Power
Consumption Versus Current Generation
PC133 Devices
Available in Plastic 24-Pin TSSOP
Phase-Lock Loop Clock Distribution for
Synchronous DRAM Applications
Distributes One Clock Input to One Bank of
Five and One Bank of Four Outputs
Separate Output Enable for Each Output
Bank
External Feedback (FBIN) Terminal Is Used
to Synchronize the Outputs to the Clock
Input
•
•
•
25-Ω On-Chip Series Damping Resistors
No External RC Network Required
Operates at 3.3 V
APPLICATIONS
•
•
•
DRAM Applications
PLL Based Clock Distributors
Non-PLL Clock Buffer
PW PACKAGE
(TOP VIEW)
AGND
VCC
1Y0
1Y1
1Y2
GND
GND
1Y3
1Y4
VCC
1G
FBOUT
1
24
2
23
3
22
4
21
5
20
6
19
7
18
8
17
9
16
10
15
11
14
12
13
CLK
AVCC
VCC
2Y0
2Y1
GND
GND
2Y2
2Y3
VCC
2G
FBIN
DESCRIPTION
The CDCVF2509 is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL to
precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. It is
specifically designed for use with synchronous DRAMs. The CDCVF2509 operates at a 3.3-V VCC. It also
provides integrated series-damping resistors that make it ideal for driving point-to-point loads.
One bank of five outputs and one bank of four outputs provide nine low-skew, low-jitter copies of CLK. Output
signal duty cycles are adjusted to 50%, independent of the duty cycle at CLK. Each bank of outputs is enabled or
disabled separately via the control (1G and 2G) inputs. When the G inputs are high, the outputs switch in phase
and frequency with CLK; when the G inputs are low, the outputs are disabled to the logic-low state.
Unlike many products containing PLLs, the CDCVF2509 does not require external RC networks. The loop filter
for the PLL is included on-chip, minimizing component count, board space, and cost.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2010, Texas Instruments Incorporated
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION CONTINUED
Because it is based on PLL circuitry, the CDCVF2509 requires a stabilization time to achieve phase lock of the
feedback signal to the reference signal. This stabilization time is required following power up and application of a
fixed-frequency, fixed-phase signal at CLK, and following any changes to the PLL reference or feedback signals.
The PLL can be bypassed by strapping AVCC to ground.
The CDCVF2509A is characterized for operation from 0°C to 85°C.
For application information, see application reports High Speed Distribution Design Techniques for
CDC509/516/2509/2510/2516 (SLMA003) and Using CDC2509A/2510A PLL with Spread Spectrum Clocking
(SSC) (SCAA039).
FUNCTION TABLE
INPUTS
OUTPUTS
1G
2G
CLK
1Y (0:4)
2Y (0:3)
X
X
L
L
L
FBOUT
L
L
L
H
L
L
H
L
H
H
L
H
H
H
L
H
H
L
H
H
H
H
H
H
H
FUNCTIONAL BLOCK DIAGRAM
1G
11
3
4
5
8
9
2G
CLK
AVCC
2
1Y1
1Y2
1Y3
1Y4
14
24
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÁÁÁÁÁÁ
ÎÎÎÎÎÎ
ÁÁÁÁÁÁ
ÎÎÎÎÎÎ
ÁÁÁÁÁÁ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
PLL
FBIN
1Y0
13
21
20
17
16
12
2Y0
2Y1
2Y2
2Y3
FBOUT
23
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
www.ti.com
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
AVAILABLE OPTIONS
PACKAGE
TA
SMALL OUTLINE (PW)
0°C to 85°C
CDCVF2509PWR
CDCVF2509PW
PACKAGE THERMAL RESISTANCE (1)
CDCVF2509APW 24-PIN TSSOP
RqJA
High K
RqJC
High K
(1)
THERMAL AIRFLOW (CFM)
0
150
250
500
88
83
81
77
26.5
UNIT
°C/W
The package thermal impedance is calculated in accordance with JESD 51 and JEDEC2S2P (high-k board).
Pin Functions
PIN
NAME
NO.
TYPE
DESCRIPTION
CLK
24
I
Clock input. CLK provides the clock signal to be distributed by the CDCVF2509A clock driver. CLK
is used to provide the reference signal to the integrated PLL that generates the clock output signals.
CLK must have a fixed frequency and fixed phase for the PLL to obtain phase lock. Once the circuit
is powered up and a valid CLK signal is applied, a stabilization time is required for the PLL to phase
lock the feedback signal to its reference signal.
FBIN
13
I
Feedback input. FBIN provides the feedback signal to the internal PLL. FBIN must be hard-wired to
FBOUT to complete the PLL. The integrated PLL synchronizes CLK and FBIN so that there is
nominally zero phase error between CLK and FBIN.
1G
11
I
Output bank enable. 1G is the output enable for outputs 1Y(0:4). When 1G is low, outputs 1Y(0:4)
are disabled to a logic-low state. When 1G is high, all outputs 1Y(0:4) are enabled and switch at the
same frequency as CLK.
2G
14
I
Output bank enable. 2G is the output enable for outputs 2Y(0:3). When 2G is low, outputs 2Y(0:3)
are disabled to a logic low state. When 2G is high, all outputs 2Y(0:3) are enabled and switch at the
same frequency as CLK.
FBOUT
12
O
Feedback output. FBOUT is dedicated for external feedback. It switches at the same frequency as
CLK. When externally wired to FBIN, FBOUT completes the feedback loop of the PLL. FBOUT has
an integrated 25-Ω series-damping resistor.
1Y (0:4)
3, 4, 5, 8, 9
O
Clock outputs. These outputs provide low-skew copies of CLK. Output bank 1Y(0:4) is enabled via
the 1G input. These outputs can be disabled to a logic-low state by deasserting the 1G control
input. Each output has an integrated 25-Ω series-damping resistor.
2Y (0:3)
16, 17, 21, 20
O
Clock outputs. These outputs provide low-skew copies of CLK. Output bank 2Y(0:3) is enabled via
the 2G input. These outputs can be disabled to a logic-low state by deasserting the 2G control
input. Each output has an integrated 25-Ω series-damping resistor.
AVCC
23
Power
Analog power supply. AVCC provides the power reference for the analog circuitry. In addition, AVCC
can be used to bypass the PLL. When AVCC is strapped to ground, PLL is bypassed and CLK is
buffered directly to the device outputs.
AGND
1
Ground Analog ground. AGND provides the ground reference for the analog circuitry.
VCC
2, 10, 15, 22
Power
GND
6, 7, 18, 19
Ground Ground
Power supply
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
3
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
www.ti.com
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
UNIT
AVCC
Supply voltage range
VCC
Supply voltage range
VI
Input voltage range
(2)
AVCC < VCC +0.7 V
–0.5 V to 4.3 V
(3)
–0.5 V to 4.6 V
(3) (4)
VO
Voltage range applied to any output in the high or low state
IIK
Input clamp current (VI< 0)
–0.5 V to VCC + 0.5 V
–50 mA
IOK
Output clamp current (VO< 0 or VO > VCC)
±50 mA
IO
Continuous output current (VO = 0 to VCC)
±50 mA
Continuous current through each VCC or GND
±100 mA
Maximum power dissipation at TA = 55°C (in still air) (5)
Tstg
(1)
(2)
(3)
(4)
(5)
0.7 W
Storage temperature range
–65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
AVCC must not exceed VCC+ 0.7 V
The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
This value is limited to 4.6 V maximum.
The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils. For
more information, see the Package Thermal Considerations application note in the ABT Advanced BiCMOS Technology Data Book
(SCBD002).
DISSIPATION RATINGS
TA ≤ 25°C
POWER RATING
PACKAGE
BOARD
TYPE
RqJA
PW
JEDEC low-K
114.5°C/W
JEDEC
high-K
62.1°C/W
DERATING
FACTORS ABOVE
TA ≤ 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
920 mW
8.7 mW/°C
520 mW
390 mW
1690 mW
16.1 mW/°C
960 mW
720 mW
RECOMMENDED OPERATING CONDITIONS (1)
MIN
MAX
VCC, AVCC
Supply voltage
3
3.6
VIH
High-level input voltage
2
VIL
Low-level input voltage
VI
Input voltage
IOH
IOL
TA
Operating free-air temperature
(1)
UNIT
V
V
0.8
V
VCC
V
High-level output current
–12
mA
Low-level output current
12
mA
85
°C
0
0
Unused inputs must be held high or low to prevent them from floating.
TIMING REQUIREMENTS
over recommended ranges of supply voltage and operating free-air temperature
fclk
Clock frequency
Input clock duty cycle
Stabilization time (1)
(1)
4
MIN
MAX
UNIT
50
175
MHz
40%
60%
1
ms
The time required for the integrated PLL circuit to obtain phase lock of its feedback signal to its reference signal. For phase lock to be
obtained, a fixed-frequency, fixed-phase reference signal must be present at CLK. Until phase lock is obtained, the specifications for
propagation delay, skew and jitter parameters given in the switching characteristics table are not applicable. This parameter does not
apply for input modulation under SSC application.
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
www.ti.com
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
VIK
TEST CONDITIONS
Input clamp voltage
VOH
II = -18 mA
High-level output voltage
VOL
Low-level output voltage
IOH
High-level output current
MIN TYP (1)
VCC, AVCC
3V
MAX
UNIT
–1.2
V
IOH = -100 µA
MIN to MAX
IOH = -12 mA
3V
2.1
IOH = -6 mA
3V
2.4
IOL = 100 µA
MIN to MAX
0.2
IOL = 12 mA
3V
0.8
IOL = 6 mA
3V
VO= 1 V
3V
VO = 1.65 V
3.3 V
VO = 3.135 V
3.6 V
VCC–0.2
V
V
0.55
–28
–36
mA
-8
VO= 1.95 V
3V
VO = 1.65 V
3.3 V
VO = 0.4 V
3.6 V
10
Input current
VI = VCC or GND
3.6 V
±5
µA
Supply current (static, output not switching)
VI = VCC or GND, IO = 0,
Outputs: low or high
3.6 V, 0 V
40
µA
ΔICC
Change in supply current
One input at VCC - 0.6 V,
Other inputs at VCC or GND
3.3 V to 3.6 V
500
µA
Ci
Input capacitance
VI = VCC or GND
3.3 V
2.5
pF
Co
Output capacitance
VO = VCC or GND
3.3 V
2.8
pF
IOL
Low-level output current
II
ICC
(1)
(2)
(2)
30
40
mA
For conditions shown as MIN or MAX, use the appropriate value specified under the recommended operating conditions section.
For dynamic ICC vs Frequency, see Figure 8 and Figure 9.
SWITCHING CHARACTERISTICS
over recommended ranges of supply voltage and operating free-air temperature, CL = 25 pF (see Figure 1 and Figure 2) (1)
FROM
(INPUT)
PARAMETER
t(f)
Phase error time- static (normalized) (see
Figure 3 through Figure 6)
CLK↑ = 66 MHz to 166 MHz
tsk(o)
Output skew time (3)
Any Y
Phase error time-jitter
(4)
CLK = 66 MHz to 100 MHz
CLK = 66 MHz to 100 MHz
Jitter(cycle-cycle) (see Figure 7)
CLK = 100 MHz to 166 MHz
TO
(OUTPUT)
FBIN↑
VCC, AVCC = 3.3 V
± 0.3 V
UNIT
MIN
TYP MAX
–125
125
ps
100
ps
50
ps
Any Y
Any Y or FBOUT
(2)
–50
-70
Any Y or FBOUT
ps
-65
Duty cycle
f(CLK) > 60 MHz
Any Y or FBOUT
45%
55%
tr
Rise time
VO = 0.4 V to 2 V
Any Y or FBOUT
0.3
1.1
ns/V
tf
Fall time
VO = 2 V to 0.4 V
Any Y or FBOUT
0.3
1.1
ns/V
tPLH
Low-to-high propagation delay time, bypass
mode
CLK
Any Y or FBOUT
1.8
3.9
ns
tPHL
High-to-low propagation delay time, bypass
mode
CLK
Any Y or FBOUT
1.8
3.9
ns
(1)
(2)
(3)
(4)
The specifications for parameters in this table are applicable only after any appropriate stabilization time has elapsed.
These parameters are not production tested.
The tsk(o) specification is only valid for equal loading of all outputs.
Calculated per PC DRAM SPEC (tphase error, static-jitter(cycle-to-cycle)).
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
5
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
www.ti.com
PARAMETER MEASUREMENT INFORMATION
3V
Input
50% VCC
0V
tpd
From Output
Under Test
500 W
2V
0.4 V
Output
25 pF
50% VCC
tr
LOAD CIRCUIT FOR OUTPUTS
VOH
2V
0.4 V
VOL
tf
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 133 MHz, ZO = 50 Ω, tr ≤ 1.2 ns, tf ≤ 1.2 ns.
C. The outputs are measured one at a time with one transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
CLKIN
FBIN
tphase error
FBOUT
Any Y
tsk(o)
Any Y
Any Y
tsk(o)
Figure 2. Skew Calculations
6
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
www.ti.com
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
TYPICAL CHARACTERISTICS
STATIC PHASE ERROR
vs
LOAD CAPACITANCE
600
600
VCC = 3.3 V
fc = 100 MHz
C(LY1−n) = 25 pF || 500 Ω
TA = 25°C
See Notes A, B, and C
200
VCC = 3.3 V
fc = 133 MHz
C(LY1−n) = 25 pF || 500 Ω
TA = 25°C
See Notes A, B, and C
400
Static Phase Error − ps
400
Static Phase Error − ps
STATIC PHASE ERROR
vs
LOAD CAPACITANCE
CLK to Y1−n
0
−200
200
CLK to Y1−n
0
−200
CLK to FBOUT
CLK to FBOUT
−400
−400
−600
−600
3
8
13
18
23
28
33
38
3
8
13
C(LF) − Load Capacitance − pF
23
28
33
38
175
200
C(LF) − Load Capacitance − pF
Figure 3.
Figure 4.
STATIC PHASE ERROR
vs
SUPPLY VOLTAGE AT FBOUT
STATIC PHASE ERROR
vs
CLOCK FREQUENCY
0
0
fc = 133 MHz
C(LY) = 25 pF || 500 Ω
C(LF) = 12 pF || 500 Ω
TA = 25°C
See Notes A, B, and C
−100
−150
CLK to FBOUT
−200
−250
−100
−150
−250
−300
−350
−350
−400
−400
3.1
3.2
3.3
3.4
3.5
3.6
CLK to FBOUT
−200
−300
3
VCC = 3.3 V
C(LY) = 25 pF || 500 Ω
C(LF) = 12 pF || 500 Ω
TA = 25°C
See Notes A, B, and C
−50
Static Phase Error − ps
−50
Static Phase Error − ps
18
50
VCC − Supply Voltage at FBOUT − V
Figure 5.
75
100
125
150
fc − Clock Frequency − MHz
Figure 6.
a. Trace length FBOUT to FBIN = 5 mm, ZO = 50Ω
b. C(LY) = Lumped capacitive load Y1-n
c. C(LFx) = Lumped feedback capacitance at FBOUT = FBIN
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
7
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
www.ti.com
JITTER
vs
CLOCK FREQUENCY AT FBOUT
ANALOG SUPPLY CURRENT
vs
CLOCK FREQUENCY
140
AI CC − Analog Supply Current − mA
120
25
VCC = 3.3 V
C(LY) = 25 pF || 500 Ω
C(LF) = 12 pF || 500 Ω
TA = 25°C
See Notes C and D
Jitter − ps
100
80
60
Cycle to Cycle
40
20
0
50
75
100
125
150
175
AVCC = VCC = 3.6 V
Bias = 0/3 V
C(LY) = 25 pF || 500 Ω
C(LF) = 12 pF || 500 Ω
TA = 25°C
See Notes A and B
20
15
10
5
0
200
0
25
fc − Clock Frequency at FBOUT − MHz
50
75
100
125
150
175
200
fc − Clock Frequency − MHz
Figure 7.
Figure 8.
SUPPLY CURRENT
vs
CLOCK FREQUENCY
250
AVCC = VCC = 3.6 V
Bias = 0/3 V
C(LY) = 25 pF || 500 Ω
C(LF) = 12 pF || 500 Ω
TA = 25°C
See Notes A and B
I CC − Supply Current − mA
200
150
100
50
0
0
25
50
75
100
125
150
175
200
fc − Clock Frequency − MHz
Figure 9.
a.
b.
c.
d.
8
Trace length FBOUT to FBIN = 5 mm, ZO = 50 Ω
C(LY) = Lumped capacitive load Y1-n
C(LFx) = Lumped feedback capacitance at FBOUT = FBIN
C(LFx) = Lumped feedback capacitance at FBOUT = FBIN.
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
NOT RECOMMENDED FOR NEW DESIGNS, USE CDCVF2509A AS A REPLACEMENT
CDCVF2509
www.ti.com
SCAS737D – APRIL 2004 – REVISED FEBRUARY 2010
REVISION HISTORY
Changes from Original (April 2004) to Revision A
•
Page
Added CDCVF2509PW package number to the AVAILABLE OPTIONS table .................................................................... 3
Changes from Revision A (July 2004) to Revision B
Page
•
Changed Rise time values in the Switching Characteristics table From: Min =0.5 Max = 2.5 To: Min = 0.3 Max = 1.1 ..... 5
•
Changed Fall time values in the Switching Characteristics table From: Min =0.5 Max = 2.5 To: Min = 0.3 Max = 1.1 ....... 5
•
Changed Low-to-high propagation delay time values in the Switching Characteristics table From: Min =0.4 Max =
2.3 To: Min = 1.8 Max = 3.9 ................................................................................................................................................. 5
•
Changed High-to-low propagation delay time values in the Switching Characteristics table From: Min =0.4 Max = 2.3
To: Min = 1.8 Max = 3.9 ........................................................................................................................................................ 5
Changes from Revision B (June 2005) to Revision C
•
Page
Added NOT RECOMMENDED FOR NEW DESIGNS ......................................................................................................... 1
Changes from Revision C (January 2009) to Revision D
•
Page
Added the PACKAGE THERMAL RESISTANCE table ........................................................................................................ 3
Submit Documentation Feedback
Copyright © 2004–2010, Texas Instruments Incorporated
Product Folder Link(s): CDCVF2509
9
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
CDCVF2509PW
ACTIVE
TSSOP
PW
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
CKV2509
CDCVF2509PWG4
ACTIVE
TSSOP
PW
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
CKV2509
CDCVF2509PWR
ACTIVE
TSSOP
PW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
CKV2509
CDCVF2509PWRG4
ACTIVE
TSSOP
PW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 85
CKV2509
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CDCVF2509PWR
Package Package Pins
Type Drawing
TSSOP
PW
24
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
16.4
Pack Materials-Page 1
6.95
B0
(mm)
K0
(mm)
P1
(mm)
8.3
1.6
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CDCVF2509PWR
TSSOP
PW
24
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated