MC10E156, MC100E156 5VECL 3-Bit 4:1 Mux-Latch Description The MC10E/100E156 contains three 4:1 multiplexers followed by transparent latches with differential outputs. When both Latch Enables (LEN1, LEN2) are LOW, the latch is transparent, and output date is controlled by the multiplexer select controls (SEL0, SEL1). A logic HIGH on either LEN1 or LEN2 (or both) latches the outputs. The Master Reset (MR) overrides all other controls to set the Q outputs LOW. The 100 Series contains temperature compensation. http://onsemi.com Features • • • • • • • • • • • • • • 950 ps Max. D to Output 850 ps Max. LEN to Output Differential Outputs Asynchronous Master Reset Dual Latch-Enables PECL Mode Operating Range: VCC = 4.2 V to 5.7 V with VEE = 0 V NECL Mode Operating Range: VCC= 0 V with VEE = −4.2 V to −5.7 V Internal Input 50 kW Pulldown Resistors ESD Protection: Human Body Model; > 2 kV, Machine Model; > 200 V Meets or Exceeds JEDEC Standard EIA/JESD78 IC Latchup Test Moisture Sensitivity Level: Pb = 1 Pb−Free = 3 For Additional Information, see Application Note AND8003/D Flammability Rating: UL 94 V−0 @ 0.125 in, Oxygen Index: 28 to 34 Transistor Count = 271 devices Pb−Free Packages are Available* PLCC−28 FN SUFFIX CASE 776 MARKING DIAGRAM* 1 MCxxxE156FNG AWLYYWW xxx A WL YY WW G = 10 or 100 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 November, 2006 − Rev. 8 1 Publication Order Number: MC10E156/D MC10E156, MC100E156 D1b D1a D2d 25 24 23 D2c D2b 22 21 D2a VCCO 20 19 SEL0 26 18 Q2 SEL1 27 17 Q2 MR 28 16 VCC 15 Q1 14 Q1 VEE 1 LEN1 2 LEN2 3 13 VCCO D1c 4 12 Q0 Pinout: 28-Lead PLCC (Top View) 5 6 7 8 D1d D0a D0b D0c 9 10 11 D0a D0b D0c D0d 4:1 MUX D1a D1b D1c D1d 4:1 MUX D2a D2b D2c D2d 4:1 MUX D0d VCCO Q0 * All VCC and VCCO pins are tied together on the die. EN R Q0 D Q1 EN R Q1 D Q2 EN R Q2 MR Figure 1. 28−Lead Pinout Figure 2. Logic Diagram Table 1. PIN DESCRIPTION D0x − D3x SEL0, SEL1 LEN1, LEN2 Q0 − Q2, Q0 − Q2 MR VCC, VCCO VEE Q0 SEL0 SEL1 LEN1 LEN2 Warning: All VCC, VCCO, and VEE pins must be externally connected to Power Supply to guarantee proper operation. PIN D Table 2. FUNCTION TABLE FUNCTION ECL Input Data ECL Select Data ECL Latch Enables ECL Differential Outputs ECL Master Reset Positive Supply Negative Supply http://onsemi.com 2 SEL1 SEL0 Data L L H H L H L H a b c d MC10E156, MC100E156 Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 VCC PECL Mode Power Supply VEE = 0 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V Iout Output Current Continuous Surge TA Operating Temperature Range Tstg Storage Temperature Range qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm qJC Thermal Resistance (Junction−to−Case) Standard Board Tsol Wave Solder Condition 2 VI v VCC VI w VEE Rating Unit 8 V 6 −6 V V 50 100 mA mA 0 to +85 °C −65 to +150 °C PLCC−28 PLCC−28 63.5 43.5 °C/W °C/W PLCC−28 22 to 26 °C/W 265 265 °C Pb Pb−Free Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 4. 10E SERIES PECL DC CHARACTERISTICS VCCx = 5.0 V, VEE = 0.0 V (Note 1) 0°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 75 90 75 90 75 90 mA VOH Output HIGH Voltage (Note 2) 3980 4070 4160 4020 4105 4190 4090 4185 4280 mV VOL Output LOW Voltage (Note 2) 3050 3210 3370 3050 3210 3370 3050 3227 3405 mV VIH Input HIGH Voltage 3830 3995 4160 3870 4030 4190 3940 4110 4280 mV VIL Input LOW Voltage 3050 3285 3520 3050 3285 3520 3050 3302 3555 mV IIH Input HIGH Current 150 mA IIL Input LOW Current 150 0.5 150 0.3 0.5 0.25 0.3 0.2 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. Table 5. 10E SERIES NECL DC CHARACTERISTICS VCCx = 0.0 V; VEE = −5.0 V (Note 3) 0°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 75 90 75 90 75 90 mA VOH Output HIGH Voltage (Note 4) −1020 −930 −840 −980 −895 −810 −910 −815 −720 mV VOL Output LOW Voltage (Note 4) −1950 −1790 −1630 −1950 −1790 −1630 −1950 −1773 −1595 mV VIH Input HIGH Voltage −1170 −1005 −840 −1130 −970 −810 −1060 −890 −720 mV VIL Input LOW Voltage −1950 −1715 −1480 −1950 −1715 −1480 −1950 −1698 −1445 mV IIH Input HIGH Current 150 mA IIL Input LOW Current 150 0.5 0.3 150 0.5 0.065 0.3 0.2 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V. 4. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. http://onsemi.com 3 MC10E156, MC100E156 Table 6. 100E SERIES PECL DC CHARACTERISTICS VCCx = 5.0 V; VEE = 0.0 V (Note 5) 0°C Symbol Characteristic Min 25°C Typ Max 75 90 Min 85°C Typ Max 75 90 Min Typ Max Unit 86 103 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 6) 3975 4050 4120 3975 4050 4120 3975 4050 4120 mV VOL Output LOW Voltage (Note 6) 3190 3295 3380 3190 3255 3380 3190 3260 3380 mV VIH Input HIGH Voltage 3835 3975 4120 3835 3975 4120 3835 3975 4120 mV VIL Input LOW Voltage 3190 3355 3525 3190 3355 3525 3190 3355 3525 mV IIH Input HIGH Current 150 mA IIL Input LOW Current 0.5 0.3 0.5 0.25 0.5 0.2 150 150 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V. 6. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. Table 7. 100E SERIES NECL DC CHARACTERISTICS VCCx = 0 V; VEE = −5.0 V (Note 7) 0°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 75 90 75 90 86 103 mA VOH Output HIGH Voltage (Note 8) −1025 −950 −880 −1025 −950 −880 −1025 −950 −880 mV VOL Output LOW Voltage (Note 8) −1810 −1705 −1620 −1810 −1745 −1620 −1810 −1740 −1620 mV VIH Input HIGH Voltage −1165 −1025 −880 −1165 −1025 −880 −1165 −1025 −880 mV VIL Input LOW Voltage −1810 −1645 −1475 −1810 −1645 −1475 −1810 −1645 −1475 mV IIH Input HIGH Current 150 mA IIL Input LOW Current 150 0.5 0.3 150 0.5 0.25 0.5 0.2 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 7. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V. 8. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. http://onsemi.com 4 MC10E156, MC100E156 Table 8. AC CHARACTERISTICS VCCx = 5.0 V; VEE = 0.0 V or VCCx = 0.0 V; VEE = −5.0 V (Note 9) 0°C 25°C Characteristic Min Typ fMAX Maximum Toggle Frequency 700 1100 tPLH tPHL Propagation Delay to Output D SEL0 SEL1 LEN MR 400 550 450 350 350 600 775 650 500 600 ts Setup Time D SEL0 SEL1 400 700 600 th Hold Time D SEL0 SEL1 tRR Reset Recovery Time tPW Minimum Pulse Width tSKEW Within-Device Skew (Note 10) 50 50 50 ps tJITTER Random Clock Jitter (RMS) <1 <1 <1 ps tr tf Rise/Fall Time (20 - 80%) Symbol MR Max Min Typ 700 1100 400 550 450 350 350 600 775 650 500 600 275 300 400 400 700 600 300 100 200 −275 −300 −400 800 600 85°C 900 1050 900 800 825 400 275 Max Min Typ 700 1100 400 550 450 350 350 600 775 650 500 600 275 300 400 400 700 600 275 300 400 300 100 200 −275 −300 −400 300 100 200 −275 −300 −400 800 600 800 600 900 1050 900 800 825 400 475 700 275 Max MHz 900 1050 900 800 825 700 275 ps ps ps ps ps 400 475 Unit 475 700 ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 9. 10 Series: VEE can vary −0.46 V / +0.06 V. 100 Series: VEE can vary −0.46 V / +0.8 V. 10. Within-device skew is defined as identical transitions on similar paths through a device. Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 5 MC10E156, MC100E156 ORDERING INFORMATION Package Shipping † MC10E156FN PLCC−28 37 Units / Rail MC10E156FNG PLCC−28 (Pb−Free) 37 Units / Rail MC10E156FNR2 PLCC−28 500 / Tape & Reel MC10E156FNR2G PLCC−28 (Pb−Free) 500 / Tape & Reel MC100E156FN PLCC−28 37 Units / Rail Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 6 MC10E156, MC100E156 PACKAGE DIMENSIONS PLCC−28 FN SUFFIX PLASTIC PLCC PACKAGE CASE 776−02 ISSUE E −N− 0.007 (0.180) B Y BRK T L−M M 0.007 (0.180) U M N S T L−M S S N S D Z −M− −L− W 28 D X V 1 A 0.007 (0.180) R 0.007 (0.180) C M M T L−M T L−M S S N S N S 0.007 (0.180) H N S S G J 0.004 (0.100) −T− SEATING T L−M S N T L−M S N S K PLANE F VIEW S G1 M K1 E S T L−M S VIEW D−D Z 0.010 (0.250) 0.010 (0.250) G1 VIEW S S NOTES: 1. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM −T−, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 −−− 0.025 −−− 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 −−− 0.020 2_ 10_ 0.410 0.430 0.040 −−− http://onsemi.com 7 MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 −−− 0.64 −−− 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 −−− 0.50 2_ 10_ 10.42 10.92 1.02 −−− 0.007 (0.180) M T L−M S N S MC10E156, MC100E156 ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10E156/D