LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 LP38691 LP38693 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors Check for Samples: LP38691, LP38693 FEATURES DESCRIPTION • The LP38691/3 low dropout CMOS linear regulators provide tight output tolerance (2.0% typical), extremely low dropout voltage (250 mV @ 500mA load current, VOUT = 5V), and excellent AC performance utilizing ultra low ESR ceramic output capacitors. 1 2 • • • • • • • • • • All WSON Options are Available as AEC-Q100 Grade 1 2.0% Output Accuracy (25°C) Low Dropout Voltage: 250 mV @ 500mA (typ, 5V out) Wide Input Voltage Range (2.7V to 10V) Precision (Trimmed) Bandgap Reference Ensured Specs for -40°C to +125°C 1µA Off-State Quiescent Current Thermal Overload Protection Foldback Current Limiting PFM, SOT-223 and 6-Lead WSON Packages Enable Pin (LP38693) The low thermal resistance of the WSON, SOT-223 and PFM packages allow the full operating current to be used even in high ambient temperature environments. The use of a PMOS power transistor means that no DC base drive current is required to bias it allowing ground pin current to remain below 100 µA regardless of load current, input voltage, or operating temperature. Dropout Voltage: 250 mV (typ) @ 500mA (typ. 5V out). APPLICATIONS • • • • Hard Disk Drives Notebook Computers Battery Powered Devices Portable Instrumentation Ground Pin Current: 55 µA (typ) at full load. Precision Output Voltage: 2.0% (25°C) accuracy. Typical Application Circuits VIN VOUT VIN VOUT LP38691 ** SNS 1 PF * GND 1 PF * VIN VOUT VIN VEN 1 PF * VEN VOUT LP38693 ** SNS GND 1 PF * * Minimum value required for stability. **WSON package devices only. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2013, Texas Instruments Incorporated LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com Connection Diagrams VEN 1 N/C 2 5 GND VOUT 3 VIN 4 Figure 1. PFM (LP38691DT-X.X) – Top View See Package Number NDP0003B VIN 1 GND 2 N/C 3 Exposed Pad on Bottom (DAP) 6 VIN 5 4 Figure 2. SOT-223 (LP38693MP-X.X) – Top View See Package Number NDC0005A VIN 1 SNS GND 2 VOUT VEN 3 Figure 3. 6-Lead WSON (LP38691SD-X.X) – Top View See Package Number NGG0006A Exposed Pad on Bottom (DAP) 6 VIN 5 SNS 4 VOUT Figure 4. 6-Lead WSON (LP38693SD-X.X) – Top View See Package Number NGG PIN DESCRIPTIONS Pin Description VIN This is the input supply voltage to the regulator. For WSON devices, both VIN pins must be tied together for full current operation (250mA maximum per pin). GND Circuit ground for the regulator. For the PFM and SOT-223 packages this is thermally connected to the die and functions as a heat sink when the soldered down to a large copper plane. SNS Output sense pin allows remote sensing at the load which will eliminate the error in output voltage due to voltage drops caused by the resistance in the traces between the regulator and the load. This pin must be tied to VOUT. VEN The enable pin allows the part to be turned ON and OFF by pulling this pin high or low. VOUT Regulated output voltage DAP WSON Only - The DAP (Exposed Pad) functions as a thermal connection when soldered to a copper plane. See WSON MOUNTING section in APPLICATION HINTS for more information. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 ABSOLUTE MAXIMUM RATINGS (1) (2) −65°C to +150°C Storage Temperature Range Lead Temp. (Soldering, 5 seconds) 260°C ESD Rating (3) 2 kV Power Dissipation (4) Internally Limited V(max) All pins (with respect to GND) -0.3V to 12V IOUT (5) Internally Limited Junction Temperature −40°C to +150°C (1) (2) (3) (4) (5) Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications, see Electrical Characteristics. Specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin. At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used). The junction-to-ambient thermal resistance ( θJ-A) for the PFM is approximately 90°C/W for a PC board mounting with the device soldered down to minimum copper area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the PFM, the θJ-A drops to approximately 50°C/W. The SOT-223 package has a θJ-A of approximately 125°C/W when soldered down to a minimum sized pattern (less than 0.1 square inch) and approximately 70°C/W when soldered to a copper area of one square inch. The θJ-A values for the WSON package are also dependent on trace area, copper thickness, and the number of thermal vias used (refer to the TI (AN-1187 Application Report) and the WSON MOUNTING section in this datasheet). If power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown. If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground. OPERATING RATINGS VIN Supply Voltage 2.7V to 10V −40°C to +125°C Operating Junction Temperature Range Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 3 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VOUT + 1V, CIN = COUT = 10 µF, ILOAD = 10mA. Min/Max limits are specified through testing, statistical correlation, or design. Symbol Parameter Conditions Min Typ (1) Max -2.0 2.0 -4.0 4.0 Units VO Output Voltage Tolerance 100 µA < IL < 0.5A VO + 1V ≤ VIN ≤ 10V ΔVO/ΔVIN Output Voltage Line Regulation (2) VO + 0.5V ≤ VIN ≤ 10V IL = 25mA 0.03 0.1 %/V ΔVO/ΔIL Output Voltage Load Regulation (3) 1 mA < IL < 0.5A VIN = VO + 1V 1.8 5 %/A (VO = 2.5V) IL = 0.1A IL = 0.5A 80 430 145 725 (VO = 3.3V) IL = 0.1A IL = 0.5A 65 330 110 550 (VO = 5V) IL = 0.1A IL = 0.5A 45 250 100 450 VIN ≤ 10V, IL =100 µA - 0.5A 55 100 VEN ≤ 0.4V, (LP38693 Only) 0.001 VIN - VOUT Dropout Voltage (4) IQ Quiescent Current IL(MIN) Minimum Load Current VIN - VO ≤ 4V IFB Foldback Current Limit VIN - VO > 5V 350 VIN - VO < 4V 850 VIN = VO + 2V(DC), with 1V(p-p) / 120Hz Ripple 55 Ripple Rejection TSD Thermal Shutdown Activation (Junction Temp) 160 TSD (HYST) Thermal Shutdown Hysteresis (Junction Temp) 10 en Output Noise BW = 10Hz to 10kHz VO = 3.3V 0.7 VO (LEAK) Output Leakage Current VO = VO(NOM) + 1V @ 10VIN 0.5 VEN Enable Voltage (LP38693 Only) Output = OFF (1) (2) (3) (4) 4 Enable Pin Leakage (LP38693 Only) mV µA 100 PSRR IEN 1 %VOUT mA dB °C µV/√Hz 12 µA 0.4 Output = ON, VIN = 4V 1.8 Output = ON, VIN = 6V 3.0 Output = ON, VIN = 10V 4.0 VEN = 0V or 10V, VIN = 10V -1 V 0.001 1 µA Typical numbers represent the most likely parametric norm for 25°C operation. Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage. Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load. Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 BLOCK DIAGRAMS VIN P-FET N/C + ENABLE LOGIC P-FET MOSFET DRIVER FOLDBACK CURRENT LIMITING VOUT SNS THERMAL SHUTDOWN 1.25V REFERENCE R1 R2 GND Figure 5. LP38691 Functional Diagram (WSON) VIN P-FET + ENABLE LOGIC P-FET MOSFET DRIVER FOLDBACK CURRENT LIMITING THERMAL SHUTDOWN VOUT 1.25V REFERENCE R1 R2 GND Figure 6. LP38691 Functional Diagram (PFM) Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 5 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com VIN P-FET VEN ENABLE LOGIC + P-FET MOSFET DRIVER FOLDBACK CURRENT LIMITING VOUT SNS THERMAL SHUTDOWN 1.25V REFERENCE R1 R2 GND Figure 7. LP38693 Functional Diagram (WSON) VIN P-FET VEN ENABLE LOGIC + P-FET MOSFET DRIVER FOLDBACK CURRENT LIMITING THERMAL SHUTDOWN VOUT 1.25V REFERENCE R1 R2 GND Figure 8. LP38693 Functional Diagram (SOT-223) 6 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise specified: TJ = 25°C, CIN = COUT = 10 µF, Enable pin is tied to VIN (LP38693 only), VOUT = 1.8V, VIN = VOUT +1V, IL = 10mA. Noise vs Frequency Noise vs Frequency Figure 9. Figure 10. Noise vs Frequency Ripple Rejection 60 RIPPLE REJECTION (dB) 50 40 30 COUT = 10 PF 20 VIN(DC) = 5.3V VIN(AC) = 1V(p-p) 10 VOUT = 3.3V 0 10 100 1k 10k 100k FREQUENCY (Hz) Figure 11. Figure 12. Ripple Rejection 60 50 50 RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) Ripple Rejection 60 40 30 COUT = 100 PF 20 VIN(DC) = 5.3V VIN(AC) = 1V(p-p) 10 40 30 COUT = 1 PF 20 VIN(DC) = 5.3V VIN(AC) = 1V(p-p) 10 VOUT = 3.3V VOUT = 3.3V 0 0 10 100 1k 10k 100k 10 FREQUENCY (Hz) 100 1k 10k 100k FREQUENCY (Hz) Figure 13. Figure 14. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 7 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25°C, CIN = COUT = 10 µF, Enable pin is tied to VIN (LP38693 only), VOUT = 1.8V, VIN = VOUT +1V, IL = 10mA. Line Transient Response Line Transient Response VOUT = 3.3V COUT = 100 PF 'VOUT (mV) 20 10 VOUT 0 -10 -20 4 VIN (V) 5 VIN 3 200 Ps/DIV 8 Figure 15. Figure 16. Line Transient Response Load Transient Response Figure 17. Figure 18. Load Transient Response VOUT vs Temperature (5.0V) Figure 19. Figure 20. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25°C, CIN = COUT = 10 µF, Enable pin is tied to VIN (LP38693 only), VOUT = 1.8V, VIN = VOUT +1V, IL = 10mA. VOUT vs Temperature (3.3V) VOUT vs Temperature (2.5V) Figure 21. Figure 22. VOUT vs Temperature (1.8V) VOUT vs VIN (1.8V) Figure 23. Figure 24. VOUT vs VIN, Power-Up VOUT vs VEN, ON (LP38693 Only) Figure 25. Figure 26. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 9 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25°C, CIN = COUT = 10 µF, Enable pin is tied to VIN (LP38693 only), VOUT = 1.8V, VIN = VOUT +1V, IL = 10mA. VOUT vs VEN, OFF (LP38693 Only) Enable Voltage vs Temperature Figure 27. Figure 28. Load Regulation vs Temperature Line Regulation vs Temperature Figure 29. Figure 30. MIN VIN vs IOUT Dropout Voltage vs IOUT 2.7 900 800 2.6 700 VDROPOUT (mV) MIN VIN (V) 2.5 2.4 -40°C 2.3 2.2 500 400 125°C 300 25°C 125°C 2.1 -40°C 600 200 100 25°C 2 0 0 100 200 300 400 500 0 200 300 400 500 IOUT (mA) IOUT (mA) Figure 31. 10 100 Figure 32. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 APPLICATION HINTS EXTERNAL CAPACITORS Like any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be correctly selected for proper performance. INPUT CAPACITOR: An input capacitor of at least 1µF is required (ceramic recommended). The capacitor must be located not more than one centimeter from the input pin and returned to a clean analog ground. OUTPUT CAPACITOR: An output capacitor is required for loop stability. It must be located less than 1 centimeter from the device and connected directly to the output and ground pins using traces which have no other currents flowing through them. The minimum amount of output capacitance that can be used for stable operation is 1µF. Ceramic capacitors are recommended (the LP38691/3 was designed for use with ultra low ESR capacitors). The LP38691/3 is stable with any output capacitor ESR between zero and 100 Ohms. ENABLE PIN (LP38693 only): The LP38693 has an Enable pin (EN) which allows an external control signal to turn the regulator output On and Off. The Enable On/Off threshold has no hysteresis. The voltage signal must rise and fall cleanly, and promptly, through the ON and OFF voltage thresholds. The Enable pin has no internal pull-up or pull-down to establish a default condition and, as a result, this pin must be terminated either actively or passively. If the Enable pin is driven from a source that actively pulls high and low, the drive voltage should not be allowed to go below ground potential or higher than VIN. If the application does not require the Enable function, the pin should be connected directly to the VIN pin. Foldback Current Limiting: Foldback current limiting is built into the LP38691/3 which reduces the amount of output current the part can deliver as the output voltage is reduced. The amount of load current is dependent on the differential voltage between VIN and VOUT. Typically, when this differential voltage exceeds 5V, the load current will limit at about 350 mA. When the VIN - VOUT differential is reduced below 4V, load current is limited to about 850 mA. SELECTING A CAPACITOR It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. Capacitor Characteristics CERAMIC For values of capacitance in the 10 to 100 µF range, ceramics are usually larger and more costly than tantalums but give superior AC performance for bypassing high frequency noise because of very low ESR (typically less than 10 mΩ). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within ±20% of nominal over full operating ratings of temperature and voltage. Of course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance. Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 11 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com TANTALUM Solid Tantalum capacitors have good temperature stability: a high quality Tantalum will typically show a capacitance value that varies less than 10-15% across the full temperature range of -40°C to +125°C. ESR will vary only about 2X going from the high to low temperature limits. REVERSE VOLTAGE A reverse voltage condition will exist when the voltage at the output pin is higher than the voltage at the input pin. Typically this will happen when VIN is abruptly taken low and COUT continues to hold a sufficient charge such that the input to output voltage becomes reversed. A less common condition is when an alternate voltage source is connected to the output. There are two possible paths for current to flow from the output pin back to the input during a reverse voltage condition. 1. While VIN is high enough to keep the control circuity alive, and the Enable pin (LP38693 only) is above the VEN(ON) threshold, the control circuitry will attempt to regulate the output voltage. If the input voltage is less than the programmed output voltage, the control circuit will drive the gate of the pass element to the full ON condition. In this condition, reverse current will flow from the output pin to the input pin, limited only by the RDS(ON) of the pass element and the output to input voltage differential. Discharging an output capacitor up to 1000 μF in this manner will not damage the device as the current will rapidly decay. However, continuous reverse current should be avoided. When the Enable pin is low this condition will be prevented. 2. The internal PFET pass element has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode is reverse biased. However, when VIN is below the value where the control circuity is alive, or the Enable pin is low (LP38693 only), and the output voltage is more than 500 mV (typical) above the input voltage the parasitic diode becomes forward biased and current flows from the output pin to the input pin through the diode. The current in the parasitic diode should be limited to less than 1A continuous and 5A peak. If used in a dual-supply system where the regulator output load is returned to a negative supply, the output pin must be diode clamped to ground to limit the negative voltage transition. A Schottky diode is recommended for this protective clamp. PCB LAYOUT Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator using traces which do not have other currents flowing in them (Kelvin connect). The best way to do this is to lay out CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a "single point ground". It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane were used at the ground points of the IC and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and it’s capacitors fixed the problem. Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. WSON MOUNTING The NGG0006A (No Pullback) 6-Lead WSON package requires specific mounting techniques which are detailed in the TI AN-1187 Application Report. Referring to the section PCB Design Recommendations (Page 5), it should be noted that the pad style which should be used with the WSON package is the NSMD (non-solder mask defined) type. Additionally, it is recommended the PCB terminal pads to be 0.2 mm longer than the package pads to create a solder fillet to improve reliability and inspection. The input current is split between two VIN pins, 1 and 6. The two VIN pins must be connected together to ensure that the device can meet all specifications at the rated current. The thermal dissipation of the WSON package is directly related to the printed circuit board construction and the amount of additional copper area connected to the DAP. 12 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 LP38691, LP38693 www.ti.com SNVS321K – JANUARY 2005 – REVISED APRIL 2013 The DAP (exposed pad) on the bottom of the WSON package is connected to the die substrate with a conductive die attach adhesive. The DAP has no direct electrical (wire) connection to any of the pins. There is a parasitic PN junction between the die substrate and the device ground. As such, it is strongly recommend that the DAP be connected directly to the ground at device lead 2 (i.e. GND). Alternately, but not recommended, the DAP may be left floating (i.e. no electrical connection). The DAP must not be connected to any potential other than ground. For the LP38691SD and LP38693SD in the NGG0006A 6-Lead WSON package, the junction-to-case thermal rating, θJC, is 10.4°C/W, where the case is the bottom of the package at the center of the DAP. The junction-toambient thermal performance for the LP38691SD and LP38693SD in the NGG0006A 6-Lead WSON package, using the JEDEC JESD51 standards is summarized in the following table: Board Type Thermal Vias θJC θJA JEDEC 2-Layer JESD 51-3 None 10.4°C/W 237° C/W 1 10.4°C/W 74° C/W 2 10.4°C/W 60° C/W 4 10.4°C/W 49° C/W 6 10.4°C/W 45° C/W JEDEC 4-Layer JESD 51-7 RFI/EMI SUSCEPTIBILITY RFI (radio frequency interference) and EMI (electromagnetic interference) can degrade any integrated circuit’s performance because of the small dimensions of the geometries inside the device. In applications where circuit sources are present which generate signals with significant high frequency energy content (> 1 MHz), care must be taken to ensure that this does not affect the IC regulator. If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the IC. If a load is connected to the IC output which switches at high speed (such as a clock), the high-frequency current pulses required by the load must be supplied by the capacitors on the IC output. Since the bandwidth of the regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that frequency. This means the effective output impedance of the IC at frequencies above 100 kHz is determined only by the output capacitor(s). In applications where the load is switching at high speed, the output of the IC may need RF isolation from the load. It is recommended that some inductance be placed between the output capacitor and the load, and good RF bypass capacitors be placed directly across the load. PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces. Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At MHz frequencies, ground planes begin to look inductive and RFI/ EMI can cause ground bounce across the ground plane. In multi-layer PCB applications, care should be taken in layout so that noisy power and ground planes do not radiate directly into adjacent layers which carry analog power and ground. OUTPUT NOISE Noise is specified in two ways: Spot Noise or Output Noise Density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a function of frequency. Total Output Noise or Broad-Band Noise is the RMS sum of spot noise over a specified bandwidth, usually several decades of frequencies. Attention should be paid to the units of measurement. Spot noise is measured in units µV/root-Hz or nV/root-Hz and total output noise is measured in µV(rms) The primary source of noise in low-dropout regulators is the internal reference. Noise can be reduced in two ways: by increasing the transistor area or by increasing the current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a smaller package. Increasing the current drawn by the internal reference increases the total supply current (ground pin current). Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 13 LP38691, LP38693 SNVS321K – JANUARY 2005 – REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision J (April 2013) to Revision K • 14 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 13 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LP38691 LP38693 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LP38691DT-1.8 NRND TO-252 NDP 3 75 TBD Call TI Call TI -40 to 125 LP38691 DT-1.8 LP38691DT-1.8/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-1.8 LP38691DT-2.5 NRND TO-252 NDP 3 75 TBD Call TI Call TI -40 to 125 LP38691 DT-2.5 LP38691DT-2.5/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-2.5 LP38691DT-3.3 NRND TO-252 NDP 3 75 TBD Call TI Call TI -40 to 125 LP38691 DT-3.3 LP38691DT-3.3/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-3.3 LP38691DT-5.0 ACTIVE TO-252 NDP 3 75 TBD Call TI Call TI -40 to 125 LP38691DT-5.0/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691DTX-1.8 ACTIVE TO-252 NDP 3 2500 TBD Call TI Call TI -40 to 125 LP38691DTX-1.8/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691DTX-2.5 ACTIVE TO-252 NDP 3 2500 TBD Call TI Call TI -40 to 125 LP38691DTX-2.5/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-2.5 LP38691DTX-3.3 NRND TO-252 NDP 3 2500 TBD Call TI Call TI -40 to 125 LP38691 DT-3.3 LP38691DTX-3.3/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-3.3 LP38691DTX-5.0 ACTIVE TO-252 NDP 3 2500 TBD Call TI Call TI -40 to 125 LP38691DTX-5.0/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 125 LP38691 DT-5.0 LP38691QSD-1.8/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L256B LP38691QSD-2.5/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L257B Addendum-Page 1 LP38691 DT-5.0 LP38691 DT-1.8 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LP38691QSD-3.3/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L258B LP38691QSD-5.0/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L259B LP38691QSDX-1.8/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L256B LP38691QSDX-2.5/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L257B LP38691QSDX-3.3/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L258B LP38691QSDX-5.0/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L259B LP38691SD-1.8 NRND WSON NGG 6 1000 TBD Call TI Call TI -40 to 125 L118B LP38691SD-1.8/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L118B LP38691SD-2.5/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L119B LP38691SD-3.3/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L120B LP38691SD-5.0/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L121B LP38691SDX-1.8/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L118B LP38691SDX-2.5/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L119B LP38691SDX-3.3/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L120B LP38691SDX-5.0/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L121B LP38693MP-1.8 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LJVB LP38693MP-1.8/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJVB LP38693MP-2.5/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJXB LP38693MP-3.3 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LJYB Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LP38693MP-3.3/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJYB LP38693MP-5.0/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJZB LP38693MPX-1.8/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJVB LP38693MPX-2.5/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJXB LP38693MPX-3.3 NRND SOT-223 NDC 5 2000 TBD Call TI Call TI -40 to 125 LJYB LP38693MPX-3.3/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJYB LP38693MPX-5.0/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LJZB LP38693QSD-1.8/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L260B LP38693QSD-2.5/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L261B LP38693QSD-3.3/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L262B LP38693QSD-5.0/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L263B LP38693QSDX-1.8/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L260B LP38693QSDX-2.5/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L261B LP38693QSDX-3.3/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L262B LP38693QSDX-5.0/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L263B LP38693SD-1.8 NRND WSON NGG 6 1000 TBD Call TI Call TI -40 to 125 L128B LP38693SD-1.8/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L128B LP38693SD-2.5/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L129B LP38693SD-3.3 NRND WSON NGG 6 1000 TBD Call TI Call TI -40 to 125 L130B Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) LP38693SD-3.3/NOPB Package Type Package Pins Package Drawing Qty ACTIVE WSON NGG 6 1000 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L130B (4/5) LP38693SD-5.0 NRND WSON NGG 6 1000 TBD Call TI Call TI -40 to 125 L131B LP38693SD-5.0/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L131B LP38693SDX-1.8/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L128B LP38693SDX-2.5/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L129B LP38693SDX-3.3/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L130B LP38693SDX-5.0/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L131B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LP38691, LP38691-Q1, LP38693, LP38693-Q1 : • Catalog: LP38691, LP38693 • Automotive: LP38691-Q1, LP38693-Q1 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LP38691DTX-1.8/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LP38691DTX-2.5/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LP38691DTX-3.3 TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LP38691DTX-3.3/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LP38691DTX-5.0/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2 LP38691QSD-1.8/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSD-2.5/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSD-3.3/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSD-5.0/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSDX-1.8/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSDX-2.5/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSDX-3.3/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691QSDX-5.0/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SD-1.8 WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SD-1.8/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SD-2.5/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SD-3.3/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SD-5.0/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LP38691SDX-1.8/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SDX-2.5/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SDX-3.3/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38691SDX-5.0/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693MP-1.8 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MP-1.8/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MP-2.5/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MP-3.3 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MP-3.3/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MP-5.0/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MPX-1.8/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MPX-2.5/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MPX-3.3/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693MPX-5.0/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP38693QSD-1.8/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSD-2.5/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSD-3.3/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSD-5.0/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSDX-1.8/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSDX-2.5/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSDX-3.3/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693QSDX-5.0/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693MPX-3.3 LP38693SD-1.8 WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-1.8/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-2.5/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-3.3 WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-3.3/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-5.0 WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SD-5.0/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SDX-1.8/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SDX-2.5/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SDX-3.3/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LP38693SDX-5.0/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP38691DTX-1.8/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LP38691DTX-2.5/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LP38691DTX-3.3 TO-252 NDP 3 2500 367.0 367.0 35.0 LP38691DTX-3.3/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LP38691DTX-5.0/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0 LP38691QSD-1.8/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691QSD-2.5/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691QSD-3.3/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691QSD-5.0/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691QSDX-1.8/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691QSDX-2.5/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691QSDX-3.3/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691QSDX-5.0/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691SD-1.8 WSON NGG 6 1000 210.0 185.0 35.0 LP38691SD-1.8/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691SD-2.5/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691SD-3.3/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691SD-5.0/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38691SDX-1.8/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691SDX-2.5/NOPB WSON NGG 6 4500 367.0 367.0 35.0 Pack Materials-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP38691SDX-3.3/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38691SDX-5.0/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693MP-1.8 SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MP-1.8/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MP-2.5/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MP-3.3 SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MP-3.3/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MP-5.0/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP38693MPX-1.8/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP38693MPX-2.5/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP38693MPX-3.3 SOT-223 NDC 5 2000 367.0 367.0 35.0 LP38693MPX-3.3/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP38693MPX-5.0/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP38693QSD-1.8/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693QSD-2.5/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693QSD-3.3/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693QSD-5.0/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693QSDX-1.8/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693QSDX-2.5/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693QSDX-3.3/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693QSDX-5.0/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693SD-1.8 WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-1.8/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-2.5/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-3.3 WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-3.3/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-5.0 WSON NGG 6 1000 210.0 185.0 35.0 LP38693SD-5.0/NOPB WSON NGG 6 1000 210.0 185.0 35.0 LP38693SDX-1.8/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693SDX-2.5/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693SDX-3.3/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LP38693SDX-5.0/NOPB WSON NGG 6 4500 367.0 367.0 35.0 Pack Materials-Page 4 MECHANICAL DATA NDP0003B TD03B (Rev F) www.ti.com MECHANICAL DATA NDC0005A www.ti.com MECHANICAL DATA NGG0006A SDE06A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated