FR101SG THRU FR107SG 1.0 AMP. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Ampere A-405 Features Low forward voltage drop High current capability High reliability High surge current capability Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Axial leads, solderable per MIL-STD202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260℃/10 seconds/.375”,(9.5mm) lead lengths at 5lbs., (2.3kg) tension Mounting position: Any Weight: 0.22gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% FR Symbol FR Type Number FR FR FR FR FR 101SG 102SG 103SG 104SG 105SG 106SG 107SG Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=125℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Operating Temperature Range Storage Temperature Range VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V I(AV) 1.0 V IFSM 30 A VF 1.3 V IR 5.0 100 uA uA nS pF ℃ ℃ Trr Cj TJ TSTG 150 250 15 -65 to +150 -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. - 434 - 500 RATINGS AND CHARACTERISTIC CURVES (FR101SG THRU FR107SG) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) 0 PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms SET TIME BASE FOR 5/ 10ns/ cm FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE 1.50 50 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 1cm Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.25 1.00 0.75 0.50 0.25 0 40 30 Tj=55 0C 20 10 8.3ms Single Half Sine Wave JEDEC Method 0 0 25 50 75 100 125 150 175 1 2 4 6 8 10 20 40 o AMBIENT TEMPERATURE. ( C) NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 10 INSTANTANEOUS FORWARD CURRENT. (A) JUNCTION CAPACITANCE.(pF) 100 Tj=25 0C 1.0 0.1 Tj=25oC Pulse Width=300 s 1% Duty Cycle 1 1 10 .01 .4 100 REVERSE VOLTAGE. (V) .6 .8 1.0 1.2 FORWARD VOLTAGE. (V) - 435 - 1.4 1.6 60 80 100