defining a degree of excellence 10 TAP LEADING EDGE CONTROL STANDARD DELAY MODULES Cat 11-R5 .60 + .01 13 bel (DC) (P/N) .375 .350 3 .285 Max .10 Typ .80 Max .015 .004 .22 Max 12 Vcc 14 In 1 Gnd 7 .23 Max .012 .008 .030 .012 .008 Total Delay Delay per Tap A447-0025-10 * 22.5 ns 2.5 + 1 ns A447-0030-10 * 27 ns 3 + 1.5 ns A447-0040-10 * 36 ns 4 + 1.5 ns Rise Time 3 ns 3 ns 3 ns 5 ns 3 ns 6 ns 3 ns 50 ns 60 ns S422-0070-10 S422-0080-10 S422-0090-10 S422-0100-10 A447-0070-10 A447-0080-10 A447-0090-10 A447-0100-10 70 80 90 100 ns ns ns ns 7 8 9 10 ns ns ns ns 3 3 3 3 ns ns ns ns S422-0125-10 S422-0150-10 S422-0200-10 S422-0250-10 A447-0125-10 A447-0150-10 A447-0200-10 A447-0250-10 125 150 200 250 ns ns ns ns 12.5 15 20 25 ns ns ns ns 3 3 3 3 ns ns ns ns Tolerances Input to Taps + 2 ns or 5% , Whichever is Greater Tap to Tap + 2 ns or 7% , Whichever is Greater Delays measured @ 1.5 V levels on Leading Edge only with no loads on Taps Rise and Fall Times measured from 0.75 V to 2.4 V levels * Ref. Delay from P13, Delay P1-P13 = 4.5 ns typical Drive Capabilities Nh Logic 1 Fanout Nl Logic 0 Fanout - Temp. 0 2 .015 Min .045 .018 4 6 Ti m e i n M i n u t e s Corporate Office Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302-4496 Tel: 201-432-0463 Fax: 201-432-9542 E-Mail: [email protected] Internet: http://www.belfuse.com Pulse Voltage Rise Time Pulse Width Pulse Period Supply Current Supply Voltage 3.2 Volts 3.0 ns (10%-90%) 1.2 x Total Delay 4 x Pulse Width 80 ma Typical 5.0 Volts Electrical Characteristics Min. 4.75 2.0 Max. 5.25 Units V V V ma ma V V V ua ma ma ma ma C % % Vcc Vih Vil Ioh Iol Voh Vol Vik Iih Iil Ios Icch Iccl Ta PW d Supply Voltage Logic 1 Input Voltage Logic 0 Input Voltage Logic 1 Output Current Logic 0 Output Current Logic 1 Output Voltage Logic 0 Output voltage Input Clamp Voltage Logic 1 Input Current Logic 0 Input Current Short Circuit Output Current Logic 1 Supply Current Logic 0 Supply Current Operating Free Air Temperature Min. Input Pulse Width of Total Delay Maximum Duty Cycle Tc Temp. Coeff. of Total Delay (TD) 100 + (25000/TD) PPM/OC 0.8 -1 20 2.7 -60 0o 40 0.5 -1.2 40 -1.2 -150 50 90 70o 50 Transfer molded for better reliability Compatible with TTL & DTL circuits Terminals: Electro-Tin plate phosphor bronze Performance warranty is limited to specified parameters listed SMD - Tape & Reel available: 32mm Wide x 16mm Pitch, 500 pieces per 13" reel Infra Red 100o C .12 Min Notes 225o C Max Temp. > 185o C for 90 Seconds Max 200o C Ein Trin PW PP Iccl Vcc 20 TTL Loads Max. 10 TTL Loads Max. Recommended Temperature Profile 300o C 100o 90o .20 Max Test Conditions @ 25oC Thru-Hole A447-0050-10 A447-0060-10 .285 Max .10 Typ Part Numbers S422-0030-10 S422-0040-10 S422-0050-10 S422-0060-10 (DC) (P/N) * 4o Coplanarity + .002 S422-0025-10 bel .325 .80 Max .018 SMD .60 + .01 11 10 9 4 5 6 8 8 Other Delays and Tolerances Available Consult Sales Specifications subject to change without notice. Far East Office Bel Fuse Ltd. 8F/8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel: 852-2328-5515 Fax: 852-2352-3706 European Office Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Preston PR1 8UD Lancashire, U.K. Tel: 44-1772-556601 Fax: 44-1772-888366 13