TI1 DS90LV110ATMT 1 to 10 lvds data/clock distributor with failsafe Datasheet

DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
DS90LV110AT 1 to 10 LVDS Data/Clock Distributor with Failsafe
Check for Samples: DS90LV110AT
FEATURES
DESCRIPTION
•
•
DS90LV110A is a 1 to 10 data/clock distributor
utilizing LVDS (Low Voltage Differential Signaling)
technology for low power, high speed operation. Data
paths are fully differential from input to output for low
noise generation and low pulse width distortion. The
design allows connection of 1 input to all 10 outputs.
LVDS I/O enable high speed data transmission for
point-to-point interconnects. This device can be used
as a high speed differential 1 to 10 signal distribution
/ fanout replacing multi-drop bus applications for
higher speed links with improved signal quality. It can
also be used for clock distribution up to 200MHz.
1
2
•
•
•
•
•
•
•
•
•
•
Low jitter 400 Mbps fully differential data path
145 ps (typ) of pk-pk jitter with PRBS = 223−1
data pattern at 400 Mbps
Single +3.3 V Supply
Balanced output impedance
Output channel-to-channel skew is 35ps (typ)
Differential output voltage (VOD) is 320mV (typ)
with 100Ω termination load.
LVDS receiver inputs accept LVPECL signals
LVDS input failsafe
Fast propagation delay of 2.8 ns (typ)
Receiver open, shorted, and terminated input
failsafe
28 lead TSSOP package
Conforms to ANSI/TIA/EIA-644 LVDS standard
The DS90LV110A accepts LVDS signal levels,
LVPECL levels directly or PECL with attenuation
networks.
The LVDS outputs can be put into TRI-STATE by use
of the enable pin.
For more details, please refer to the APPLICATION
INFORMATION section of this datasheet.
Connection Diagram
Order Number DS90LV110ATMT
PW0028A Package
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2013, Texas Instruments Incorporated
DS90LV110AT
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
www.ti.com
Block Diagram
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1)
−0.3V to +4V
Supply Voltage (VDD-VSS)
−0.3V to (VCC + 0.3V)
LVCMOS/LVTTL Input Voltage (EN)
LVDS Receiver Input Voltage (IN+, IN−)
−0.3V to +4V
LVDS Driver Output Voltage (OUT+, OUT−)
−0.3V to +4V
Junction Temperature
+150°C
−65°C to +150°C
Storage Temperature Range
Lead Temperature (Soldering, 4 sec.)
+260°C
Maximum Package Power
Dissipation at 25°C
28 Lead TSSOP
2.115 W
Package Derating
28 Lead TSSOP
16.9 mW/°C above +25°C
θJA
(4-Layer, 2 oz. Cu, JEDEC)
28 Lead TSSOP
59.1 °C/W
ESD Rating:
(1)
(HBM, 1.5kΩ, 100pF)
> 8 kV
(EIAJ, 0Ω, 200pF)
> 250 V
“Absolute Maximum Ratings” are these beyond which the safety of the device cannot be verified. They are not meant to imply that the
device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Recommended Operating Conditions
Min
Typ
Max
Units
3.0
3.3
3.6
V
Supply Voltage (VDD - VSS)
Receiver Input Voltage
0
Operating Free Air Temperature
2
-40
Submit Documentation Feedback
+25
VDD
V
+85
°C
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Conditions
Min
Typ (1)
Max
Units
V
LVCMOS/LVTTL DC SPECIFICATIONS (EN)
VIH
High Level Input Voltage
2.0
VDD
VIL
Low Level Input Voltage
VSS
0.8
V
IIH
High Level Input Current
VIN = 3.6V or 2.0V; VDD = 3.6V
±20
μA
IIL
Low Level Input Current
VIN = 0V or 0.8V; VDD = 3.6V
±7
±20
μA
VCL
Input Clamp Voltage
ICL = −18 mA
−0.8
−1.5
V
mV
±7
LVDS OUTPUT DC SPECIFICATIONS (OUT1, OUT2, OUT3, OUT4, OUT5, OUT6, OUT7, OUT8, OUT9, OUT10)
VOD
Differential Output Voltage
RL = 100Ω
250
320
450
RL = 100Ω, VDD = 3.3V, TA = 25°C
260
320
425
mV
35
|mV|
ΔVOD
Change in VOD between Complimentary Output States
VOS
Offset Voltage
ΔVOS
Change in VOS between Complimentary Output States
IOZ
Output TRI-STATE Current
EN = 0V,
VOUT = VDD or GND
IOFF
Power-Off Leakage Current
ISA,ISB
Output Short Circuit Current
ISAB
Both Outputs Shorted
(2)
1.125
(3)
1.25
1.375
V
35
|mV|
±1
±10
μA
VDD = 0V; VOUT = 3.6V or GND
±1
±10
μA
VOUT+ OR VOUT− = 0V or VDD
12
24
|mA|
VOUT+ = VOUT−
6
12
|mA|
0
+100
mV
LVDS RECEIVER DC SPECIFICATIONS (IN)
VTH
Differential Input High Threshold
VTL
Differential Input Low Threshold
VCM = +0.05V or +1.2V or +3.25V,
VDD = 3.3V
−100
VCMR
Common Mode Voltage Range
VID = 100mV, VDD = 3.3V
0.05
3.25
V
IIN
Input Current
VIN = +3.0V, VDD = 3.6V or 0V
±1
±10
μA
VIN = 0V, VDD = 3.6V or 0V
±1
±10
μA
RL = 100Ω, CL = 5 pF, 200 MHz,
EN = High
125
160
mA
No Load, 200 MHz, EN = High
80
125
mA
EN = Low
15
29
mA
0
mV
SUPPLY CURRENT
ICCD
Total Supply Current
ICCZ
TRI-STATE Supply Current
(1)
(2)
(3)
All typical are given for VCC = +3.3V and TA = +25°C, unless otherwise stated.
VOS is defined as (VOH + VOL) / 2.
Only one output can be shorted at a time. Don't exceed the package absolute maximum rating.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
3
DS90LV110AT
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
www.ti.com
AC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
390
550
ps
390
550
ps
TLHT
Output Low-to-High Transition Time, 20% to 80%, Figure 4
(1)
THLT
Output High-to-Low Transition Time, 80% to 20%, Figure 4
(1)
TDJ
LVDS Data Jitter, Deterministic (Peak-toPeak) (2)
TRJ
LVDS Clock Jitter, Random
TPLHD
Propagation Low to High Delay, Figure 5
2.2
2.8
3.6
ns
TPHLD
Propagation High to Low Delay, Figure 5
2.2
2.8
3.9
ns
TSKEW
Pulse Skew |TPLHD - TPHLD|
20
340
ps
(2)
VID = 300mV; PRBS=223-1 data;
VCM = 1.2V at 400 Mbps (NRZ)
145
ps
VID = 300mV;
VCM = 1.2V at 200 MHz clock
2.8
ps
(1)
(1)
TCCS
Output Channel-to-Channel Skew, Figure 6
35
91
ps
TPHZ
Disable Time (Active to TRI-STATE) High to Z, Figure 1
3.0
6.0
ns
TPLZ
Disable Time (Active to TRI-STATE) Low to Z, Figure 1
1.8
6.0
ns
TPZH
Enable Time (TRI-STATE to Active) Z to High, Figure 1
10.0
23.0
ns
TPZL
Enable Time (TRI-STATE to Active) Z to Low, Figure 1
7.0
23.0
ns
(1)
(2)
The parameters are specified by design. The limits are based on statistical analysis of the device performance over PVT (process,
voltage and temperature) range.
The measurement used the following equipment and test setup: HP8133A pattern/pulse generator), 5 feet of RG-142 cable with DUT
test board and HP83480A (digital scope mainframe) with HP83484A (50GHz scope module). The HP8133A with the RG-142 cable
exhibit a TDJ = 26ps and TRJ = 1.3 ps
AC TIMING DIAGRAMS
Figure 1. Output active to TRI-STATE and TRI-STATE to active output time
4
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
Figure 2. LVDS Driver TRI-STATE Circuit
Figure 3. LVDS Output Load
Figure 4. LVDS Output Transition Time
Figure 5. Propagation Delay Low-to-High and High-to-Low
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
5
DS90LV110AT
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
www.ti.com
Figure 6. Output 1 to 10 Channel-to-Channel Skew
APPLICATION INFORMATION
INPUT FAIL-SAFE
The receiver inputs of the DS90LV110A have internal fail-safe biasing for short, open, and teminated input
conditions.
LVDS INPUTS TERMINATION
The LVDS Receiver input must have a 100Ω termination resistor placed as close as possible across the input
pins.
UNUSED CONTROL INPUTS
The EN control input pin has internal pull down device. If left open, the 10 outputs will default to TRI-STATE.
EXPANDING THE NUMBER OF OUTPUT PORTS
To expand the number of output ports, more than one DS90LV110A can be used. Total propagation delay
through the devices should be considered to determine the maximum expansion. Adding more devices will
increase the output jitter due to each pass.
PCB LAYOUT AND POWER SYSTEM BYPASS
Circuit board layout and stack-up for the DS90LV110A should be designed to provide noise-free power to the
device. Good layout practice also will separate high frequency or high level inputs and outputs to minimize
unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by
using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic capacitance of the
PCB power system which improves power supply filtering, especially at high frequencies, and makes the value
and placement of external bypass capacitors less critical. External bypass capacitors should include both RF
ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 µF to 0.1 µF. Tantalum
capacitors may be in the range 2.2 µF to 10 µF. Voltage rating for tantalum capacitors should be at least 5X the
power supply voltage being used. It is recommended practice to use two vias at each power pin of the
DS90LV110A as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance by up
to half, thereby reducing interconnect inductance and extending the effective frequency range of the bypass
components.
The outer layers of the PCB may be flooded with additional ground plane. These planes will improve shielding
and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally, to be
effective, these planes must be tied to the ground supply plane at frequent intervals with vias. Frequent via
placement also improves signal integrity on signal transmission lines by providing short paths for image currents
which reduces signal distortion. The planes should be pulled back from all transmission lines and component
mounting pads a distance equal to the width of the widest transmission line or the thickness of the dielectric
separating the transmission line from the internal power or ground plane(s) whichever is greater. Doing so
minimizes effects on transmission line impedances and reduces unwanted parasitic capacitances at component
mounting pads.
6
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
There are more common practices which should be followed when designing PCBs for LVDS signaling. Please
see Application Note: AN-1108(SNLA008) for additional information.
INPUT INTERFACING
The DS90LV110A accepts differential signals and allow simple AC or DC coupling. With a wide common mode
range, the DS90LV110A can be DC-coupled with all common differential drivers (that is, LVPECL, LVDS, CML).
Figure 7, Figure 8, and Figure 9 illustrate typical DC-coupled interface to common differential drivers.
LVDS
Driver
DS90LV110A
Receiver
100: Differential T-Line
OUT+
IN+
100:
IN-
OUT-
Figure 7. Typical LVDS Driver DC-Coupled Interface to DS90LV110A Input
CML3.3V or CML2.5V
Driver
VCC
50:
DS90LV110A
Receiver
50:
100: Differential T-Line
OUT+
IN+
100:
IN-
OUT-
Figure 8. Typical CML Driver DC-Coupled Interface to DS90LV110A Input
LVPECL
Driver
DS90LV110A
Receiver
100: Differential T-Line
OUT+
IN+
100:
IN-
OUT50:
50:
Figure 9. Typical LVPECL Driver DC-Coupled Interface to DS90LV110A Input
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
7
DS90LV110AT
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
www.ti.com
OUTPUT INTERFACING
The DS90LV110A outputs signals that are compliant to the LVDS standard. Their outputs can be DC-coupled to
most common differential receivers. Figure 10 illustrates typical DC-coupled interface to common differential
receivers and assumes that the receivers have high impedance inputs. While most differential receivers have a
common mode input range that can accommodate LVDS compliant signals, it is recommended to check
respective receiver's data sheet prior to implementing the suggested interface implementation.
DS90LV110A
Driver
OUT+
Differential
Receiver
100: Differential T-Line
IN+
CML or
LVPECL or
LVDS
100:
IN-
OUT-
Figure 10. Typical DS90LV110A Output DC-Coupled Interface to an LVDS, CML or LVPECL Receiver
DS90LV110A PIN DESCRIPTIONS
8
Pin Name
# of Pin
Input/Output
IN+
1
I
Non-inverting LVDS input
Description
IN -
1
I
Inverting LVDS input
OUT+
10
O
Non-inverting LVDS Output
OUT -
10
O
Inverting LVDS Output
EN
1
I
This pin has an internal pull-down when left open. A logic low on the
Enable puts all the LVDS outputs into TRI-STATE and reduces the
supply current.
VSS
3
P
Ground (all ground pins must be tied to the same supply)
VDD
2
P
Power Supply (all power pins must be tied to the same supply)
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
MULTI-DROP APPLICATIONS
POINT-TO-POINT DISTRIBUTION APPLICATIONS
For applications operating at data rate greater than 400Mbps, a point-to-point distribution application should be
used. This improves signal quality compared to multi-drop applications due to no stub PCB trace loading. The
only load is a receiver at the far end of the transmission line. Point-to-point distribution applications will have a
wider LVDS bus lines, but data rate can increase well above 400Mbps due to the improved signal quality.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
9
DS90LV110AT
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
10
Output Voltage (VOD) vs. Resistive Load (RL)
Peak-to-Peak Output Jitter at VCM = +0.4V vs. VID
Peak-to-Peak Output Jitter at VCM = +1.2V vs. VID
Peak-to-Peak Output Jitter at VCM = +2.9V vs. VID
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
DS90LV110AT
www.ti.com
SNOSAC2J – AUGUST 2004 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision I (April 2013) to Revision J
•
Page
Changed layout of National Data Sheet to TI format ............................................................................................................ 1
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV110AT
11
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DS90LV110ATMT
NRND
TSSOP
PW
28
48
TBD
Call TI
Call TI
-40 to 85
DS90LV
110ATMT
DS90LV110ATMT/NOPB
ACTIVE
TSSOP
PW
28
48
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
DS90LV
110ATMT
DS90LV110ATMTX/NOPB
ACTIVE
TSSOP
PW
28
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
DS90LV
110ATMT
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2014
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
DS90LV110ATMTX/NOPB TSSOP
PW
28
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
6.8
B0
(mm)
K0
(mm)
P1
(mm)
10.2
1.6
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS90LV110ATMTX/NOPB
TSSOP
PW
28
2500
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated