CURRENT 2.0 Amperes VOLTAGE 50 to 400 Volts ES2A THRU ES2J Features · For surface applications in order optimize board space · Low profile package · Built-in strain relief, ideal for automated placement · Super fast recovery time · Plastic package has Unerwrites Laboratory Flammability Classification 94V-0 · Ideally suited for use in very high frequency switching power supplies, inverters and as free wheeling diodes · Low forward voltage drop · Glass passivated chip junction · High temperature soldering guaranteed : 250℃/10 seconds, at terminals DO-214AA (SMB) 0.155(3.94) 0.130(3.30) 0.083(2.11) 0.075(1.91) 0.185(4.70) 0.160(4.06) 0.012(0.31) 0.006(0.15) 0.096(2.44) 0.083(2.13) Mechanical Data · Case : JEDEC SMB(DO-214AA) molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.003 ounce, 0.093 gram 0.008(0.203) MAX. 0.050(1.27) 0.030(0.76) 0.220(5.59) 0.200(5.08) Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols ES2A ES2B ES2C ES2D ES2G ES2J Units Maximum recurrent peak reverse voltage VRRM 50 100 150 200 400 600 Volts Maximum RMS voltage VRMS 35 70 105 140 280 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 400 600 Volts Maximum average forward rectified current at TL=120℃ I(AV) 2.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 50.0 Amps Maximum instantaneous forward voltage at 2.0A Maximum reverse current at rated voltage TA=25℃ TA=125℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Typical junction capacitance (Note 2) Operating junction and storage temperature range VF IR 0.95 5.0 350 Trr RθJL RθJA CJ TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Units mounted on P.C.B 5.0×5.0mm(0.013mm thick) land areas 1.25 200 Volts μA 35 μS 20.0 75.0 ℃/W 18.0 15.0 -55 to +150 pF ℃ RATINGS AND CHARACTERISTIC CURVES ES2A THRU ES2J FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-FORWARD CURRENT DERATING CURVE 30 2.0 25 1.6 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 2.4 RESISTIVE OR INDUCTIVE LOAD P.C.B. 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 1.2 0.8 0.4 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) at TL=110℃ 20 15 10 5 0 0 80 90 100 110 120 130 140 1 150 10 NUMBER OF CYCLES AT 60Hz LEAD TEMPERATURE (℃) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 50 1000 10 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) 100 1 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 100 TJ=125℃ 10 1 TJ=75℃ TJ=25℃ 0.1 1.8 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 12 TJ=25℃ f=1.0MHz Vsig=50mVp-P 10 8 6 4 2 0 0.1 1 10 REVERSE VOLTAGE. VOLTS 100 TRANSIENT THERMAL IMPEDANCE, ℃/W JUNCTIOIN CAPACITANCE(pF) 14 MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 T, PULSE DURATION ,sec. 100