LANSDALE MC12009P Mecl pll components dual modulus prescaler Datasheet

ML12009
ML12011
MECL PLL Components Dual
Modulus Prescaler
Legacy Device: Motorola MC12009, MC12011
These devices are two–modulus prescalers which will divide by
5 and 6, 8 and 9, respectively. A MECL–to–MTTL translator is
provided to interface directly with the Motorola MC12014
Counter Control Logic. In addition, there is a buffered clock input
and MECL bias voltage source.
•
•
•
•
•
•
•
16
1
SO 16 = -5P
PLASTIC PACKAGE
CASE 751B
ML12009 480 MHz (÷5/6), ML12011 550 MHz (÷8/9)
MECL to MTTL Translator on Chip
MECL and MTTL Enable Inputs
5.0 or –5.2 V Operation*
Buffered Clock Input — Series Input RC Typ, 20 Ω and 4.0 pF
VBB Reference Voltage
310 mW (Typ)
16
1
P DIP 16 = EP
PLASTIC PACKAGE
CASE 648
CROSS REFERENCE/ORDERING INFORMATION
PACKAGE
MOTOROLA
LANSDALE
* When using a 5.0 V supply, apply 5.0 V to Pin 1 (VCCO),
Pin 6 (MTTL VCC), Pin 16 (VCC), and ground Pin 8
(VEE). When using –5.2 V supply, ground Pin 1 (VCCO),
Pin 6 (MTTL VCC), and Pin 16 (VCC) and apply –5.2 V to
Pin 8 (VEE). If the translator is not required, Pin 6 may be
left open to conserve DC power drain.
P DIP 16
SOIC 16
P DIP 16
SO 16W
MC12009P
MC12009D
MC12011P
MC12011D
ML12009EP
ML12009-5P
ML12011EP
ML12011-5P
Note: Lansdale lead free (Pb) product, as it
becomes available, will be identified by a part
number prefix change from ML to MLE.
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
(Ratings above which device life may be impaired)
Power Supply Voltage
(VCC = 0)
VEE
–8.0
Vdc
Input Voltage
(VCC = 0)
Vin
0 to VEE
Vdc
Output Source Current
Continuous
Surge
IO
Storage Temperature Range
Tstg
mAdc
50
100
–65 to 175
°C
(Recommended Maximum Ratings above which performance may be
degraded)
Operating Temperature Range
ML12009, ML12011
DC Fan–Out (Note 1)
(Gates and Flip–Flops)
TA
–30 to 85
°C
n
70
—
PIN CONNECTIONS
VCCO
Q
1
Q
(–)
3
16 VCC
15 Clock
2
14 VBB
13 E1 MECL
12 E2 MECL
4
(+)
5
MTTL VCC
6
MTTL Output
7
11 E3 MECL
10 E4 MECL
VEE
8
9 E5 MECL
(Top View)
NOTES: 1. AC fan–out is limited by desired system performance.
Page 1 of 14
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
Figure 1. Logic Diagrams
ML12009
MTTL E5 9
MTTL E4 10
D
Q1
D
C
Q1
C
Q2
D
MECL
to
MTTL
Translator
Q3
MECL E3 11
MECL E2 12
MECL E1 13
15
C
Recommended Circuitry
For ac coupled Inputs.
1000 pF
Clock Input
Q3
VBB
14
0.1 µF
1.0 k
3
Q3
Q3
2
7
MTTL
Out
5 4
+ –
ML12011
MTTL E5 9
D
MTTL E4 10
MECL E3 11
Q1
D
C
MECL E2 12
MECL E1 13
Q2
C
D
C
Recommended Circuitry
For ac coupled Inputs.
15
1000 pF
Clock Input
1.0 k
Q4
Toggle
Flip
Flop
C
Q4
Q3
MECL
to
MTTL
Translator
VBB
0.1 µF
14
3 2
Q4 Q4
5 4
+ –
7
MTTL
Out
Figure 2. Typical Frequency Synthesizer Application
fref
Phase Detector
MC4044/ML4044
Voltage–Controlled
Oscillator MC1648/ML1648
Low–Pass Filter
fout
Modulus Enable Line
ML12009
ML12011
ML12013
Counter Control Logic
MC12014
Zero Detect Line
fout
Np Programmable
Counter MC4016/ML4016
A Programmable
Counter MC4016/ML4016
Counter Reset Line
Page 2 of 14
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
Figure 2b Generic block diagram showing prescaler connection to
PLL Device
Prescaler
Fout
ML12009/11
PLL
Fin
ML145146
ML145158
ML145159
MC in
MC
VCO
Loop Filter
Figure 2b shows a generic block diagram of connecting a prescaler to a PLL device that supports
dual modulus controls. Applicataion not AN535 describes using a two–modulus prescaler
technique. By using prescaler higher frequencies can be achieved than by a single CMOS PLL
device.
Page 3 of 14
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (Supply Voltage = –5.2 V, unless otherwise noted.)
Test Limits
Symbol
Pin
Under
Test
Min
ICC1
8
–88
ICC2
6
5.2
5.2
5.2
mAdc
IinH1
15
11
12
13
375
375
375
375
250
250
250
250
250
250
250
250
µAdc
IinH2
4
5
1.7
1.7
6.0
6.0
2.0
2.0
6.0
6.0
2.0
2.0
6.4
6.4
mAdc
IinH3
5
0.7
3.0
1.0
3.0
1.0
3.6
IinH4
9
10
IinL1
15
11
12
13
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
µAdc
IinL2
9
10
–1.6
–1.6
–1.6
–1.6
–1.6
–1.6
mAdc
VBB
14
VOH1
(Note 1)
2
3
–1.100
–1.100
VOH2
7
–2.8
VOL1
(Note 1)
2
3
–1.990
–1.990
VOL2
7
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 3)
2
3
IOS
7
Characteristic
Power Supply Drain Current
Input Current
Leakage Current
Reference Voltage
Logic ‘1’ Output Voltage
Logic ‘0’ Output Voltage
Short Circuit Current
–30°C
25°C
Max
Min
Max
–80
100
100
–0.890
–0.890
–1.120
–1.120
–1.360
–1.160
–1.000
–1.000
–0.810
–0.810
–1.950
–1.950
mAdc
100
100
–0.930
–0.930
–1.650
–1.650
–1.925
–1.925
–0.700
–0.700
Vdc
–1.615
–1.615
Vdc
–4.48
–0.950
–0.950
–1.630
–1.630
–65
µAdc
Vdc
–4.40
–1.655
–1.655
Unit
–2.4
–1.020
–1.020
–20
Max
–80
–2.6
–1.675
–1.675
Min
100
100
–4.26
–65
85°C
–20
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
–65
Vdc
–1.595
–1.595
Vdc
–20
mAdc
Clock Input
VIHmax
VILmin
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50 Ω resistor to –2.0 V. Test procedures are shown for only one gate. The other gates are tested in the same
manner.
Page 4 of 14
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (continued) (Supply Voltage = –5.2 V, unless otherwise noted.)
TEST VOLTAGE/CURRENT VALUES
Volts
Characteristic
Power Supply Drain Current
Input Current
Leakage Current
Reference Voltage
Logic ‘1’ Output Voltage
@ Test Temperature
VIHmax
VILmin
VIHAmin
VILAmax
VIH
VILH
–30°C
–0.890
–1.990
–1.205
–1.500
–2.8
–4.7
25°C
–0.810
–1.950
–1.105
–1.475
–2.8
–4.7
85°C
–0.700
–1.925
–1.035
–1.440
–2.8
–4.7
Symbol
Pin
Under
Test
ICC1
8
ICC2
6
4
IinH1
15
11
12
13
15
11
12
13
IinH2
4
5
5
5
4
4
6
6
IinH3
5
4
5
6
IinH4
9
10
IinL1
15
11
12
13
IinL2
9
10
VBB
14
VOH1
(Note 1)
2
3
VOH2
7
Logic ‘0’ Output Voltage
VOL1
(Note 1)
2
3
VOL2
7
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 3)
2
3
IOS
7
Short Circuit Current
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
VIHmax
VILmin
VIHAmin
VILAmax
VIL
Gnd
1,16
5
6
1,16
1,16
1,16
1,16
9
10
1,16
1,16
1,16
1,16
1,16
1,16
9
10
1,16
1,16
1,16
11,12,13
11,12,13
5
4
9,10
9,10
1,16
1,16
9,10
9,10
1,16
1,16
4
6
11,12,13
11,12,13
5
6
11,12,13
11,12,13
1,16
1,16
11,12,13
11,12,13
5
4
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
Page 5 of 14
VIH
www.lansdale.com
1,16
1,16
7
Clock Input
6
VIHmax
VILmin
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (continued) (Supply Voltage = –5.2 V, unless otherwise noted.)
TEST VOLTAGE/CURRENT VALUES
Volts
Characteristic
Power Supply Drain Current
Input Current
Leakage Current
Reference Voltage
Logic ‘1’ Output Voltage
mA
@ Test Temperature
VIHT
VILT
VEE
IL
IOL
IOH
–30°C
–3.2
–4.4
–5.2
–0.25
16
–0.40
25°C
–3.2
–4.4
–5.2
–0.25
16
–0.40
85°C
–3.2
–4.4
–5.2
–0.25
16
–0.40
Symbol
Pin
Under
Test
ICC1
8
8
1,16
ICC2
6
8
6
IinH1
15
11
12
13
8
8
8
8
1,16
1,16
1,16
1,16
IinH2
4
5
8
8
6
6
IinH3
5
8
6
IinH4
9
10
8
8
1,16
1,16
IinL1
15
11
12
13
8,15
8,11
8,12
8,13
1,16
1,16
1,16
1,16
IinL2
9
10
8
8
1,16
1,16
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
VIHT
VILT
9,10
9,10
9,10
VEE
VBB
14
8
VOH1
(Note 1)
2
3
8
8
VOH2
7
8
Logic ‘0’ Output Voltage
VOL1
(Note 1)
2
3
8
8
VOL2
7
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 2)
2
3
IOS
7
Short Circuit Current
8
9,10
9,10
9,10
9,10
www.lansdale.com
IOL
IOH
14
Gnd
1,16
1,16
1,16
7
6
1,16
1,16
7
6
8
8
1,16
1,16
8
8
1,16
1,16
8
6
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
Page 6 of 14
IL
Clock Input
VIHmax
VILmin
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (Supply Voltage = 5.0 V, unless otherwise noted.)
Test Limits
Symbol
Pin
Under
Test
Min
Power Supply Drain Current
ICC1
8
–88
ICC2
6
5.2
5.2
5.2
mAdc
Input Current
IinH1
15
11
12
13
375
375
375
375
250
250
250
250
250
250
250
250
µAdc
IinH2
4
5
1.7
1.7
6.0
6.0
6.4
6.4
mAdc
IinH3
5
0.7
3.0
IinH4
9
10
IinL1
15
11
12
13
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
–10
µAdc
IinL2
9
10
–1.6
–1.6
–1.6
–1.6
–1.6
–1.6
mAdc
VBB
14
VOH1
(Note 1)
2
3
3.900
3.900
VOH2
7
2.4
VOL1
(Note 1)
2
3
3.070
3.070
VOL2
7
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 3)
2
3
IOS
7
Characteristic
Leakage Current
Reference Voltage
Logic ‘1’ Output Voltage
Logic ‘0’ Output Voltage
Short Circuit Current
–30°C
25°C
Max
Min
–80
4.110
4.110
6.0
6.0
2.0
2.0
1.0
3.0
1.0
100
100
100
100
3.67
3.87
4.000
4.000
4.190
4.190
2.6
3.385
3.385
3.880
3.880
3.110
3.110
3.6
µAdc
Vdc
4.070
4.070
3.410
3.410
3.135
3.135
4.300
4.300
Vdc
3.445
3.445
Vdc
0.72
4.050
4.050
3.430
3.430
–65
Unit
mAdc
100
100
0.80
3.405
3.405
Max
2.8
3.980
3.980
–20
Min
–80
2.0
2.0
0.94
–65
85°C
Max
–20
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
–65
Vdc
3.465
3.465
Vdc
–20
mAdc
Clock Input
VIHmax
VILmin
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50 Ω resistor to –2.0 V. Test procedures are shown for only one gate. The other gates are tested in the same
manner.
Page 7 of 14
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (continued) (Supply Voltage = 5.0 V, unless otherwise noted.)
TEST VOLTAGE/CURRENT VALUES
Volts
@ Test Temperature
VIHmax
VILmin
VIHAmin
VILAmax
VIH
VILH
–30°C
4.110
3.070
3.795
3.500
2.4
0.5
25°C
4.190
3.110
3.895
3.525
2.4
0.5
85°C
4.300
3.135
3.965
3.560
2.4
0.5
Symbol
Pin
Under
Test
Power Supply Drain Current
ICC1
8
ICC2
6
4
Input Current
IinH1
15
11
12
13
15
11
12
13
IinH2
4
5
5
5
4
4
IinH3
5
4
5
IinH4
9
10
IinL1
15
11
12
13
IinL2
9
10
VBB
14
VOH1
(Note 1)
2
3
VOH2
7
VOL1
(Note 1)
2
3
VOL2
7
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 3)
2
3
IOS
7
Characteristic
Leakage Current
Reference Voltage
Logic ‘1’ Output Voltage
Logic ‘0’ Output Voltage
Short Circuit Current
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
VIHmax
VILmin
VIHAmin
VILAmax
VIL
(VEE)
Gnd
8
5
8
8
8
8
8
8
8
8
9
10
8
8
8,15
8,11
8,12
8,13
9
10
8
8
8
11,12,13
11,12,13
5
9,10
9,10
4
11,12,13
11,12,13
4
9,10
9,10
5
8
8
11,12,13
11,12,13
4
www.lansdale.com
8
8
8
11,12,13
11,12,13
5
8
8
8
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
Page 8 of 14
VIH
8
8
7
Clock Input
8
VIHmax
VILmin
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
ELECTRICAL CHARACTERISTICS (continued) (Supply Voltage = 5.0 V, unless otherwise noted.)
TEST VOLTAGE/CURRENT VALUES
Volts
@ Test Temperature
Characteristic
Power Supply Drain Current
Input Current
Leakage Current
Reference Voltage
mA
VIHT
VILT
VCC
IL
IOL
IOH
–30°C
2.0
0.8
5.0
–0.25
16
–0.40
25°C
2.0
0.8
5.0
–0.25
16
–0.40
85°C
2.0
0.8
5.0
–0.25
16
–0.40
Symbol
Pin
Under
Test
ICC1
8
1,16
8
ICC2
6
6
8
IinH1
15
11
12
13
1,16
1,16
1,16
1,16
8
8
8
8
IinH2
4
5
6
6
8
8
IinH3
5
6
8
IinH4
9
10
1,16
1,16
8
8
IinL1
15
11
12
13
1,16
1,16
1,16
1,16
8,15
8,11
8,12
8,13
IinL2
9
10
1,16
1,16
8
8
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
VIHT
VILT
9,10
9,10
9,10
VCC
VBB
14
1,16
VOH1
(Note 1)
2
3
1,16
1,16
VOH2
7
6
VOL1
(Note 1)
2
3
1,16
1,16
VOL2
7
6
Logic ‘1’ Threshold Voltage
VOHA
(Note 2)
2
3
Logic ‘0’ Threshold Voltage
VOLA
(Note 3)
2
3
IOS
7
Logic ‘1’ Output Voltage
Logic ‘0’ Output Voltage
Short Circuit Current
9,10
9,10
9,10
9,10
www.lansdale.com
IOL
IOH
14
(VEE)
Gnd
8
8
8
7
8
8
8
7
8
1,16
1,16
8
8
1,16
1,16
8
8
6
8
NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and
ground voltages must be maintained between tests. The clock input is the waveform shown.
2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock
input is the waveform shown.
3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock
input is the waveform shown.
Page 9 of 14
IL
Clock Input
VIHmax
VILmin
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
SWITCHING CHARACTERISTICS
ML12509, ML12511, ML12513
TEST VOLTAGES/WAVEFORMS APPLIED TO PINS LISTED BELOW:
Characteristic
Symbol
Pin
Under
Test
Propagation Delay
(See Figures 3 and 5)
t15+ 2+
t15+ 2–
t5+ 7+
t5– 7–
2
2
7
7
—
—
—
—
—
—
—
—
8.1
7.5
8.4
6.5
—
—
—
—
—
—
—
—
8.1
7.5
8.1
6.5
—
—
—
—
—
—
—
—
8.9
82
8.9
7.1
ns
15
15
A
A
—
—
—
—
—
—
—
—
—
—
—
—
11,12,13
11,12,13
—
—
9,10
9,10
—
—
8
8
8
8
1,6,16
1,6,16
1,6,16
1,6,16
Setup Time
(See Figures 4 and 5)
tsetup1
tsetup2
11
9
5.0
5.0
—
—
—
—
5.0
5.0
—
—
—
—
5.0
5.0
—
—
—
—
ns
ns
15
15
*
—
—
*
—
—
*
11,12,13
9,10
*
8
8
1,6,16
1,6,16
Release Time
(See Figures 4 and 5)
trel1
trel2
11
9
5.0
5.0
—
—
—
—
5.0
5.0
—
—
—
—
5.0
5.0
—
—
—
—
ns
ns
15
15
*
—
—
*
—
—
*
11,12,13
9.10
*
8
8
1,6,16
1,6,16
Toggle Frequency
(See Figure 6)
ML12509 : 5/6
ML12511 : 8/9
fmax
2
440
500
—
—
—
—
480
550
—
—
—
—
440
500
—
—
—
—
—
—
—
—
—
—
11
11
—
—
—
—
8
8
16
16
–30°C
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Pulse
Gen.1
Pulse
Gen.2
Pulse
Gen.3
VIHmin
VILmin
VF
–3.0 V
VEE
–3.0 V
VCC
+2.0
MHz
*Test inputs sequentially, with Pulse Generator 2 or 3 as indicated connected to input under test, and the voltage indicated applied to the other input(s) of the same type ( i.e., MECL or MTTL).
–30°C
25°C
85°C
VIHmin
1.03
1.115
1.20
Vdc
VILmin
0.175
0.200
0.235
Vdc
Figure 3. AC Voltage Waveforms
Pulse
Generator
1
20%
t++
Q (Pin 2)
VIHmin
80%
50%
VILmin
50%
t+ –
50%
Q (Pin 3)
+ In
50%
MTTL
Out
t++
t––
–1.5 V
Figure 4. Setup and Release Time Waveforms
Pulse
50
Generator
%
1 tsetup1
Pulse
Generator
tsetup2
2
Pulse
Generator
+1.5 V
3
Q (Pin 2)
Page 10 of 14
80%
20%
80%
50%
VIHmin
VILmin
VIHmin
20%
VILmin
0V
10%
VEE
90%
Divide by 5 — ML12509
Divide by 8 — ML12511
Di id b 10
ML12513
Pulse
Generator
1
Pulse
50%
Generator t
rel2
2
Pulse
Generator
3
–1.5 V
Q (Pin 2)
www.lansdale.com
80%
20%
50%
trel1
80%
20%
90%
10%
VIHmin
VILmin
VIHmin
VILmin
0V
VEE
Divide by 6 — ML12509
Divide by 9 — ML12511
Di id b 11
ML12513
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
Figure 5. AC Test Circuit
Vin
25 µF
50
Pulse
Generator
#1
Vout (Scope Channel B)
VCC = 2.0 V
100
Vin
50
Pulse
Generator
#2
100
Vin
1
13
E1
12
E2
11
E3
10
E4
9
E5
15
C
950
50
0.1 µF
16
Q
Q
Vout
2
3
Vout
VBB
14
Pulse
Generator
#3
6
5
+
4
–
MECL
to
MTTL
Trans–
lator
1950
7
8
MC10109 or equiv.
0.1 µF
Vin
(Scope Channel A)
CT
VEE = –3.0 V
A
All Pulse Generators are EH 137 or equiv.
Pulse Generators 1 and 2:
PRF = 10 MHz
PW = 50% Duty Cycle
t + = t – = 2.0 ± 0.2 ns
Pulse Generator 3:
PRF = 2.0 MHz
PW = 50% Duty Cycle
t + = t – = 5.0 ± 0.5 ns
Page 11 of 14
50
VEE = –3.0 V
All resistors are +1%.
All input and output cables to the scope are equal lengths of 50 Ω coaxial cable.
The 1950 Ω resistor at Pin 7 and the scope termination impedance constitute a 40 :1 attenuator probe.
CT = 15 pF = total parasitic capacitance which includes probe, wiring, and load capacitance.
Unused output connected to a 50 Ω resistor to ground.
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
Figure 6. Maximum Frequency Test Circuit
Vout
VCC = 2.0 V
0.1 µF
1
13
(To Scope)
Vin
VEE
2
E3
10
E4
9
E5
15
1.0 k
Q
E2
11
0.1 µF
5.0 µF
16
E1
12
to
Scope
Q
3
C
14
VBB
0.1 µF
8
0.1 µF
VEE = –3.0 V
Unused output connected to a 50 Ω resistor to ground
DIVIDE BY 6
800 mV
Clock
Input
850 mV typ
Q (Pin 2)
3 Cycles
3 Cycles
DIVIDE BY 9
800 mV
Clock
Input
850 mV typ
Q (Pin 2)
Page 12 of 14
5 Cycles
4 Cycles
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
Figure 7. State Diagram
DIVIDE BY 5/6 (ML12009/ML12509)
Enable = 0
Q1
1
0
0
0
1
1
Q2
1
1
0
0
0
1
Q3
1
1
1
0
0
0
Enable = 0
Q2
1
1
0
0
1
1
0
0
1
011
001
110
100
000
0101
0010
1110
0110
010
101
1000
1100
1010
0000
0111
1111
Enable = 1
Enable = 1
Q1
1
0
0
1
1
0
0
1
1
111
DIVIDE BY 8/9 (ML12011)
Q3
1
1
1
0
0
1
1
0
0
Q4
1
1
1
1
1
0
0
0
0
Enable = 1
0001
1101
1001
0011
Enable = 1
1011
0100
APPLICATIONS INFORMATION
The primary application of these devices is as a
high–speed variable modulus prescaler in the divide by N
section of a phase–locked loop synthesizer used as the local
oscillator of two–way radios.
Proper VHF termination techniques should be followed
when the clock is separated from the prescaler by any
appreciable distance.
Page 13 of 14
In their basic form, these devices will divide by 5/6 or 8/9.
Division by 5, or 8 occurs when any one or all of the five gate
inputs E1 through E5 are high. Division by 6, or 9 occurs
when all inputs E1 through E5 are low. (Unconnected MTTL
inputs are normally high, unconnected MECL inputs are
normally low). With the addition of extra parts, many different
division configurations may be obtained.
www.lansdale.com
Issue A
ML12009, ML12011
LANSDALE Semiconductor, Inc.
OUTLINE DIMENSIONS
SO 16 = -5P
PLASTIC PACKAGE
(ML12009-5P, ML12011-5P)
CASE 751B–05
(SO–16)
ISSUE J
–A–
16
9
–B–
1
P
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
8 PL
0.25 (0.010)
8
B
M
S
G
R
K
–T–
F
X 45
C
SEATING
PLANE
D
J
M
16 PL
0.25 (0.010)
M
T B
S
A
S
P DIP 16 = EP
PLASTIC PACKAGE
(ML12009EP, ML12011EP)
CASE 648–08
ISSUE R
–A–
16
9
1
8
B
F
C
L
S
–T–
H
SEATING
PLANE
K
G
D
J
16 PL
0.25 (0.010)
M
T A
M
M
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.229
0.244
0.010
0.019
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0
10
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0
10
0.51
1.01
Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent rights nor the rights of others. “Typical” parameters which
may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s
technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc.
Page 14 of 14
www.lansdale.com
Issue A