Coilcraft DO5040H-684KL Smt power inductors â do5040h Datasheet

Document 479-1
SMT Power Inductors – DO5040H
• Heavy gauge wire and self-leaded terminations for low DCR
• Saturation current ratings as high as 33.4 A
DCR
SRF4
Inductance2 max
typ Isat4 Irms5
Part number1
(µH)
(mOhms) (MHz) (A) (A)
DO5040H-282ML_ 2.8 ±20%
5.2
DO5040H-392ML_ 3.9 ±20%
6.0
DO5040H-682ML_ 6.8 ±20%
9.0
DO5040H-103ML_ 10 ±20%
11
DO5040H-123ML_ 12 ±20%
13
DO5040H-153ML_ 15 ±20%
20
DO5040H-183ML_ 18 ±20%
22
DO5040H-223ML_ 22 ±20%
24
DO5040H-333ML_ 33 ±20%
37
DO5040H-473ML_ 47 ±20%
52
DO5040H-683ML_ 68 ±20%
67
DO5040H-104ML_ 100 ±20%
115
DO5040H-334KL_ 330 ±10%
325
DO5040H-684KL_ 680 ±10%
780
DO5040H-145KL_ 1400 ±10%
1300
65
40
30
22
21
18
14
13
10
8.0
7.0
6.0
3.0
1.6
1.0
33.4
26.8
22.5
17.8
15.9
13.8
13.2
11.8
9.6
7.8
6.7
5.6
3.0
2.0
1.5
12.1
11.2
9.6
8.6
7.4
6.5
6.0
5.7
4.5
3.7
3.4
2.8
1.5
1.1
0.7
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant tin-silver (96.5/3.5) over copper. Other
terminations available at additional cost.
Weight 5.8 – 7.6 g (2.8 –12 µH); 5.7 – 7.0 g (15 –1400 µH)
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel
2.8 –12 µH parts Plastic tape: 44 mm wide, 0.5 mm thick,
24 mm pocket spacing, 12.8 mm pocket depth
15 –1400 µH parts Plastic tape: 32 mm wide, 0.4 mm thick,
24 mm pocket spacing, 12.1 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
1. When ordering, please specify termination and packaging codes:
DO5040H-104MLD
Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (175 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc using Coilcraft
SMD‑A fixture in Agilent/HP 4284A impedance analyzer.
3. SRF measured using Agilent/HP 8753D network analyzer and Coilcraft
SMD­‑D test fixture.
4. DC current at which the inductance drops 10% (typ) from its value without current.
5. Current that causes a 40°C temperature rise from 25°C ambient.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 479-1
Revised 02/25/15
Document 479-2
SMT Power Inductors - DO5040H Series
Typical L vs Current
Typical L vs Frequency
1000
100 µH
100
Inductance (µH)
Inductance (µH)
1000
33 µH
12 µH
10
100 µH
100
33 µH
12 µH
10
2.8 µH
2.8 µH
1
1
0.1
Current (A)
10
100
Current Derating
1
0.001
0.01
0.1
Frequency (MHz)
1
10
2.8 µH – 12 µH
100
90
80
70
60
50
40
25°C
Percent of rated current
120
110
30
20
10
0
Isat
Irms
-40
-20
0
20
40
60
80
100
120
140
Ambient temperature (°C)
15 µH – 1400 µH
Dimensions are in
inches
mm
Document 479-2
Revised 02/25/15
Similar pages