GF1A THRU GF1M SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER * Reverse Voltage - 50 to 1000 Volts FEATURES T E D DO-214BA N E P A T Forward Current - 1.0 Ampere 0.060 (1.52) 0.040 (1.02) 0.187 (4.75) 0.167 (4.24) 0.0105 (0.27) 0.0065 (0.17) 0.108 (2.74) 0.098 (2.49) 0.118 (3.00) 0.106 (2.69) 0.114 (2.90) 0.094 (2.39) 0.152 TYP. 0.006 0.060 (1.52) 0.030 (0.76) 0.226 (5.74) 0.196 (4.98) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Ideal for surface mount automotive applications ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ Built-in strain relief ♦ Easy pick and place ♦ High temperature soldering guaranteed: 450°C/5 seconds at terminals ♦ Complete device submersible temperature of 265°C for 10 seconds in solder bath MECHANICAL DATA Dimensions in inches and (millimeters) *Glass-plastic encapsulation technique is covered by Patent No. 3,996,602, brazed-lead assembly by Patent No. 3,930,306 and lead forming by Patent No. 5,151,846 ® Case: JEDEC DO-214BA molded plastic over glass body Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.0048 ounces, 0.120 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS Device marking code GF1A GF1B GF1D GF1G GF1J GF1K GF1M GA GB GD GG GJ GK GM UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TL=125°C I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 Amps VF 1.10 IR 5.0 50.0 µA Typical reverse recovery time (NOTE 1) trr 2.0 µs Typical junction capacitance (NOTE 2) CJ 15.0 pF RΘJA RΘJL 80.0 26.0 °C/W TJ, TSTG -65 to +175 °C Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=125°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied VR=4.0 Volts (3) Thermal resistance from junction to ambient and from junction to lead P.C.B. mounted on 0.2 x 0.2” (5.0 x 5.0mm) copper pad areas 4/98 1.20 Volts RATINGS AND CHARACTERISTIC CURVES GF1A THRU GF1M FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 60 HZ RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED on 0.2 x 0.2” (5.0 x 5.0mm) COPPER PAD AREAS 1.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 0.5 0 100 110 120 130 140 150 160 175 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 25 20 15 10 5.0 0 LEAD TEMPERATURE, °C 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 1 TJ=100°C 0.1 TJ=25°C 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE (°C/W) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 30 100 MOUNTED ON 0.20 x 0.27” (5 x 7mm) COPPER PAD AREAS 10 1 0.1 0.01 0.1 1 t, PULSE DURATION, sec 10 100