WJ AG201-86PCB Ingap hbt gain block Datasheet

AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
Product Features
Product Description
Functional Diagram
x DC – 6000 MHz
x +6.5 dBm P1dB at 900 MHz
x +19.5 dBm OIP3 at 900 MHz
x 11 dB Gain at 900 MHz
x Single Voltage Supply
x Green SOT-86 SMT Package
x Internally matched to 50 :
The AG201-86 is a general-purpose buffer amplifier that
offers high dynamic range in a low-cost surface-mount
package. At 900 MHz, the AG201-86 typically provides
11 dB gain, +19.5 dBm OIP3, and +6.5 dBm P1dB. The
device combines dependable performance with consistent
quality to maintain MTTF values exceeding 100 years at
mounting temperatures of +85 qC & is housed in a SOT-86
(micro-X) industry-standard SMT lead-free/green/RoHScompliant package.
GND
Applications
The AG201-86 consists of Darlington pair amplifiers using
the high reliability InGaP/GaAs HBT process technology
and only requires DC-blocking capacitors, a bias resistor,
and an inductive RF choke for operation.
x Mobile Infrastructure
x CATV / DBS
x W-LAN / ISM
x RFID
x Defense / Homeland Security
x Fixed Wireless
RF In
3 RF Out
1
2
GND
Function
Input
Output/Bias
Ground
Pin No.
1
3
2, 4
The broadband MMIC amplifier can be directly applied to
various current and next generation wireless technologies
such as GPRS, GSM, CDMA, and W-CDMA. In addition,
the AG201-86 will work for other various applications
within the DC to 6 GHz frequency range such as CATV
and fixed wireless.
Specifications (1)
Parameter
4
Typical Performance (1)
Units
Min
MHz
MHz
dB
dB
dB
dBm
dBm
dBm
dB
MHz
dB
dBm
dBm
V
mA
DC
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output IP3 (2)
Output IP2
Output P1dB
Noise Figure
Test Frequency
Gain
Output IP3 (2)
Output P1dB
Device Voltage
Device Current
9.6
Typ
Parameter
Max
6000
900
10.9
25
20
+19.3
+27
+6.7
4.4
1900
10.6
+18.4
+6.1
4.0
20
Units
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
MHz
dB
dB
dB
dBm
dBm
dB
500
11.0
-25
-18
+6.7
+19.6
4.4
Typical
900
10.9
-25
-20
+6.7
+19.3
4.4
1900
10.6
-25
-18
+6.1
+18.4
4.5
2140
10.4
-16
-14
+5.4
+18.0
4.5
11.6
1. Test conditions: 25º C, Supply Voltage = +5 V, Rbias = 49.9 , 50 System.
2. 3OIP measured with two tones at an output power of -10 dBm/tone separated by 10 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
DC Voltage
RF Input Power (continuous)
Junction Temperature
Rating
-40 to +85 qC
-55 to +125 qC
+4.5 V
+10 dBm
+250 qC
Ordering Information
Part No.
*
Operation of this device above any of these parameters may cause permanent damage.
Description
AG201-86*
InGaP HBT Gain Block
AG201-86G
InGaP HBT Gain Block
AG201-86PCB
700 – 2400 MHz Fully Assembled Eval. Board
(lead-tin SOT-86 Pkg)
(lead-free/green/RoHS-compliant SOT-86 Pkg)
This package is being phased out in favor of the green package type which is backwards compatible for
existing designs. Refer to Product Change Notification WJPCN06MAY05TC1 on the WJ website.
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 1 of 6 June 2005
AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
Typical Device RF Performance
Supply Bias = +5 V, Rbias = 49.9 :, Icc = 20 mA
Frequency
S21
S11
S22
Output P1dB
Output IP3
Noise Figure
MHz
dB
dB
dB
dBm
dBm
dB
100
11.0
-35
-49
+6.8
+19.9
4.3
500
11.0
-25
-18
+6.7
+19.6
4.4
900
10.9
-25
-20
+6.7
+19.3
4.4
1900
10.6
-25
-18
+6.1
+18.4
4.5
2140
10.4
-16
-14
+5.4
+18.0
4.5
2400
10.2
-16
-14
+5.2
+17.5
4.6
3500
9.8
-16
-16
+3.7
5800
8.6
-15
-16
1. Test conditions: T = 25º C, Supply Voltage = +5 V, Device Voltage = 4.0 V, Rbias = 49.9 , Icc = 20 mA typical, 50 System.
2. 3OIP measured with two tones at an output power of -10 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit.
10
8
6
+25 C
+85 C
3
0
4
1
2
4
5
0
3.0
1.5
2
25
20
-40c
2.5
3
+25c
0
200
Frequency (GHz)
2
+85c
Gain (dB)
0
-5
1
1.5
2
2.5
600
800
0
1000
0.5
3
Frequency (GHz)
3.5
4
12
10
8
8
8
4
6
0
-4
Output Power
-20
-16
-8
-12
-8
-4
Input Power (dBm)
1
1.5
+85 C
2
2.5
3
Output Power / Gain vs. Input Power
Gain
2
+25 C
Frequency (GHz)
4
+85 C
-10
0.5
400
frequency = 900 MHz
10
0
-40 C
Frequency (MHz)
5
+25 C
3
Output Power / Gain vs. Input Power
12
-40 C
4
1
P1dB vs. Frequency
10
4.5
5
Output Power (dBm)
1
4.0
Noise Figure vs. Frequency
6
15
0.5
3.5
Device Voltage (V)
30
+85 C
5
0
10
6
NF (dB)
OIP2 (dBm)
10
P1dB (dBm)
3
Output IP2 vs. Frequency
35
15
+25 C
S22
Frequency (GHz)
20
-40 C
-30
Optimal operating point
20
-40
Output IP3 vs. Frequency
25
OIP3 (dBm)
2
Frequency (GHz)
-20
30
0
Gain (dB)
1
-10
S11
4
0
I-V Curve
40
frequency = 2000 MHz
6
Gain
6
2
4
-2
2
-6
Output Power
0
4
10
-20
-16
-12
-8
-4
Input Power (dBm)
Output Power (dBm)
S11, S22 (dB)
Gain (dB)
12
-40 C
Return Loss
0
Device Current (mA)
Gain vs. Frequency
14
-10
0
4
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 2 of 6 June 2005
AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
Typical Device RF Performance (cont’d)
Supply Bias = +6 V, Rbias = 100 :, Icc = 20 mA
Gain vs. Frequency
OIP3 (dBm)
Gain (dB)
12
10
8
6
-40 C
+25 C
1
+85 C
2
Frequency (GHz)
3
10
30
25
20
+85 C
-40c
5
+25c
+85c
15
0
4
0.5
1
1.5
2
2.5
3
0
200
Frequency (GHz)
P1dB vs. Frequency
10
400
600
800
1000
Frequency (MHz)
Noise Figure vs. Frequency
6
5
5
NF (dB)
P1dB (dBm)
15
+25 C
Output IP2 vs. Frequency
35
20
-40 C
4
0
Output IP3 vs. Frequency
25
OIP2 (dBm)
14
0
-5
-40 C
+25 C
4
3
2
+85 C
-40 C
1
-10
0
0.5
1
1.5
2
2.5
3
3.5
0
4
0.5
+25 C
1
Frequency (GHz)
+85 C
1.5
2
2.5
3
Frequency (GHz)
Typical Device RF Performance
Supply Bias = +8 V, Rbias = 200 :, Icc = 20 mA
Gain vs. Frequency
OIP3 (dBm)
Gain (dB)
12
10
8
6
-40 C
+25 C
1
+85 C
2
Frequency (GHz)
3
10
30
25
20
+85 C
-40c
5
+25c
+85c
15
0
4
0.5
1
1.5
2
2.5
3
0
200
Frequency (GHz)
P1dB vs. Frequency
10
400
600
800
1000
Frequency (MHz)
Noise Figure vs. Frequency
6
5
5
NF (dB)
P1dB (dBm)
15
+25 C
Output IP2 vs. Frequency
35
20
-40 C
4
0
Output IP3 vs. Frequency
25
OIP2 (dBm)
14
0
-5
-40 C
+25 C
4
3
2
+85 C
-40 C
1
-10
0
0.5
1
1.5
2
2.5
3
3.5
0
4
Frequency (GHz)
0.5
+25 C
1
1.5
+85 C
2
2.5
3
Frequency (GHz)
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 3 of 6 June 2005
AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
Vcc
Icc = 20 mA
Application Circuit
R1
Bias
Resistor
C4
Bypass
Capacitor
C3
0.018 µF
L1
RF Choke
RF IN
RF OUT
AG201-86
C2
Blocking
Capacitor
C1
Blocking
Capacitor
Recommended Component Values
Reference
Designator
50
500
L1
820 nH
220 nH
C1, C2, C4
.018 µF
1000 pF
Frequency (MHz)
900
1900
2200
68 nH
27 nH
22 nH
100 pF
68 pF
68 pF
2500
18 nH
56 pF
Recommended Bias Resistor Values
S upply
R1 value
S ize
Voltage
5V
50 ohms
0603
6V
100 ohms
0603
7V
150 ohms
0805
8V
200 ohms
0805
9V
250 ohms
1206
10 V
300 ohms
1210
12 V
400 ohms
1210
3500
15 nH
39 pF
1. The proper values for the components are dependent upon the intended frequency of operation.
2. The following values are contained on the evaluation board to achieve optimal broadband performance:
Ref. Desig.
L1
C1, C2
C3
C4
R1
Value / Type
39 nH wirewound inductor
56 pF chip capacitor
0.018 PF chip capacitor
Do Not Place
49.9 : 1% tolerance
Size
0603
0603
0603
The proper value for R1 is dependent upon the supply
voltage and allows for bias stability over temperature.
WJ recommends a minimum supply bias of +5 V. A
1% tolerance resistor is recommended.
0603
Typical Device Data
S-Parameters (Vdevice = +4.0 V, ICC = 20 mA, T = 25 C, calibrated to device leads)
Freq (MHz)
50
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
3500
3750
4000
4250
4500
4750
5000
5250
5500
5750
6000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
S12 (ang)
S22 (dB)
S22 (ang)
-37.64
-36.83
-28.79
-26.43
-25.90
-24.64
-25.23
-25.62
-24.17
-18.82
-18.60
-17.60
-17.02
-16.90
-17.13
-17.44
-18.06
-18.57
-19.22
-20.15
-21.62
-21.42
-19.52
-16.22
-14.14
3.52
62.61
123.66
112.89
101.70
95.33
83.50
60.45
33.27
12.49
2.15
-9.59
-15.59
-14.88
-14.40
-9.24
-2.17
4.02
7.64
4.43
-8.53
-41.85
-67.93
-87.83
-94.75
11.24
11.23
11.22
11.16
11.08
11.03
10.94
10.86
10.70
10.53
10.42
10.30
10.19
10.10
9.99
9.89
9.81
9.68
9.56
9.40
9.27
9.11
8.94
8.79
8.62
178.11
171.63
163.07
154.89
146.68
138.31
130.36
122.04
113.83
106.17
100.66
92.52
85.00
77.62
70.26
62.87
55.29
47.96
40.36
32.52
25.17
17.74
10.90
3.67
-3.25
-16.00
-16.46
-16.50
-16.41
-16.70
-16.45
-16.43
-16.39
-16.39
-16.37
-16.72
-16.24
-16.24
-16.35
-16.50
-16.27
-16.29
-15.91
-15.94
-16.12
-15.89
-15.92
-15.59
-15.69
-15.55
1.11
-0.14
-5.66
-8.53
-13.42
-15.06
-17.48
-19.90
-23.75
-26.76
-33.51
-33.22
-34.24
-36.14
-39.41
-44.09
-47.05
-49.81
-53.84
-55.91
-60.31
-64.69
-66.43
-70.84
-74.11
-16.68
-17.04
-19.51
-20.19
-20.62
-20.86
-20.47
-19.22
-17.91
-14.33
-14.51
-14.25
-14.75
-15.68
-17.51
-20.51
-24.24
-24.92
-22.53
-20.67
-19.51
-19.11
-18.45
-16.76
-15.72
-3.15
-7.62
-16.81
-27.72
-38.34
-54.50
-67.94
-78.99
-87.16
-87.39
-92.27
-97.25
-102.71
-107.08
-113.93
-129.70
-153.32
160.54
132.24
123.31
126.82
136.47
151.24
166.71
173.37
Device S-parameters are available for download off of the website at: http://www.wj.com
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 4 of 6 June 2005
AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
AG201-86 (Sot-86 Package) Mechanical Information
This package may contain lead-bearing materials. The plating material on the leads is SnPb.
Outline Drawing
Product Marking
The component will be marked with an “A”
designator followed by a two-digit numeric
lot code on the top surface of the package.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
Land Pattern
ESD Rating:
Value:
Test:
Standard:
Class 0
Passes at 150 V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ESD Rating:
Value:
Test:
Standard:
Class II
Passes at 250 V
Charged Device Model (CDM)
JEDEC Standard JESD22-C101
MSL Rating: Level 1
Standard:
JEDEC Standard J-STD-020
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance
of this device. Vias should use a .35mm (#80 / .0135” )
diameter drill and have a final plated thru diameter of .25 mm
(.010” ).
2. Add as much copper as possible to inner and outer layers near
the part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the
board to a heatsink. Ensure that the ground / thermal via
region contacts the heatsink.
4. Do not put solder mask on the backside of the PC board in the
region where the board contacts the heatsink.
5. RF trace width depends upon the PC board material and
construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are in
degrees.
Thermal Specifications
Parameter
Rating
Operating Case Temperature
Thermal Resistance, Rth (1)
Junction Temperature, Tjc (2)
-40 to +85 qC
395 qC/W
117 qC
1. The thermal resistance is referenced from the hottest part
of the junction to the ground lead (pin 2 or 4).
2. This corresponds to the typical biasing condition of +4V,
20 mA at an 85 C case temperature. A minimum
MTTF of 1 million hours is achieved for junction
temperatures below 177 C.
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 5 of 6 June 2005
AG201-86
The Communications Edge TM
Product Information
InGaP HBT Gain Block
AG201-86G (Green / Lead-free Sot-86 Package) Mechanical Information
This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260qC reflow temperature) and leaded
(maximum 245qC reflow temperature) soldering processes. The plating material on the pins is annealed matte tin over copper.
Product Marking
Outline Drawing
The component will be marked with an “ L”
designator followed by a two-digit numeric
lot code on the top surface of the package.
Tape and reel specifications for this part are
located on the website in the “ Application
Notes” section.
MSL / ESD Rating
Land Pattern
ESD Rating:
Value:
Test:
Standard:
Class 1C
Passes at 1000 V min.
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ESD Rating:
Value:
Test:
Standard:
Class IV
Passes at 1000 V min.
Charged Device Model (CDM)
JEDEC Standard JESD22-C101
MSL Rating: Level 3 at +260 C convection reflow
Standard:
JEDEC Standard J-STD-020
Mounting Config. Notes
1. Ground / thermal vias are critical for the proper performance
of this device. Vias should use a .35mm (#80 / .0135” )
diameter drill and have a final plated thru diameter of .25 mm
(.010” ).
2. Add as much copper as possible to inner and outer layers near
the part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the
board to a heatsink. Ensure that the ground / thermal via
region contacts the heatsink.
4. Do not put solder mask on the backside of the PC board in the
region where the board contacts the heatsink.
5. RF trace width depends upon the PC board material and
construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are in
degrees.
Thermal Specifications
Rating
Operating Case Temperature
Thermal Resistance, Rth (1)
Junction Temperature, Tjc (2)
-40 to +85 qC
395 qC/W
117 qC
1. The thermal resistance is referenced from the hottest part
of the junction to the ground lead (pin 2 or 4).
2. This corresponds to the typical biasing condition of +4V,
20 mA at an 85 C case temperature. A minimum
MTTF of 1 million hours is achieved for junction
temperatures below 177 C.
MTTF (million hrs)
Parameter
MTTF vs. GND Lead Temperature
10000
1000
100
10
60
70
80
90
100
Ground Lead Temperature (°C)
110
Specifications and information are subject to change without notice
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 6 of 6 June 2005
Similar pages