MB05S-MB10S Silicon Bridge Rectifiers VOLTAGE RANGE: 50 --- 1000 V CURRENT: 0.5 A MBS Features 3.8±0.2 0.6±0.1 Mechanical Data 1.2±0.2 This series is UL recognized under Component Index, file number E239431 Glass passivated chip junctions Plastic materrial has U/L flammability classification 94V-O High surge overload rating: 35A peak Saves space on printed circuit boards High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.3kg) tension 2.5±0.2 4.6±0.2 1.0±0.15 2.5±0.25 0.3±0.1 6.8±0.2 Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Dimensions in inches and (millimeters) Mounting Position: Any Weight: 0.0078 ounce, 0.22 gram Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%. MB05S MB1S MB2S MB4S MB6S MB8S MB10S UNITS Maximum recurrent peak reverse voltage V RRM 50 100 200 400 600 800 1000 V Maximum RMS voltage V RMS 35 70 140 280 420 560 700 V Maximum DC blocking voltage V DC 50 100 200 400 600 800 1000 V Maximum average forw ard output current @TA=25 IF(AV) 0.5 A IFSM 35.0 A VF 1.0 V 5.0 μA 0.5 mA CJ 13 pF R θJA RθJL 85 20 TJ - 55 ---- + 150 TSTG - 55 ---- + 150 Peak forw ard surge current 8.3ms single half-sine-w ave superimposed on rated load Maximum instantaneous forw ard voltage @ 0.4 A Maximum reverse current at rated DC blocking voltage @TA=25 @TA=100 Typical junction capacitance per leg (NOTE 3) Typical thermal resistance per leg (NOTE 1) (NOTE 2) Operating junction temperature range Storage temperature range IR NOTES: (1) On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.3 x 1.3mm) pads (2) On aluminum substrate P.C.B. with an area of 0.8" x 0.8" (20 x 20mm) mounted on 0.05 x 0.05" (1.3 x 1.3mm) solder pad (3) Measured at 1.0 MHz and applied rev erse v oltage of 4.0 Volts /W MB05S-MB10S Silicon Bridge Rectifiers Ratings AND Charactieristic Curves FIG.2 -- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 0.8 Aluminum Substrate 0.7 GLASS EPOXY P.C.B. 0.6 0.5 0.4 0.3 0.2 0.1 0 RESISTIVE OR INDUCTIVE LOAD 30 0 60 90 120 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG.1 -- DERATING CURVE FOR OUTPUT RRECTIFIED CURRENT TＡ=４０ SINGLE HALF SINE-WAVE (JEDEC Method) 30 25 f=60Hz 20 15 f=50Hz 10 1.0 CYCLE 5.0 0 1 10 100 NUMBER OF CYCLES AT 50/60Hz AMBIENT TEMPERATURE, 10 1 INSTANTANEOUS REVERSE CURRENT, MICRO AMPERES FIG.4 -- TYPICAL REVERSE CHARACTERISTIC FIG.3 -- TYPICAL FORWARD VOLTAGE KKKKCHARACTERISTICS PER LEG TJ=25 0.1 0.01 0.2 0.6 0.8 1.0 1.2 TJ=125 10 1.0 0.1 TJ=25 .01 20 0 40 60 80 100 FIG.5 -- TYPICAL JUNCTION CAPACITANCE PER BBBBBBB ELEMENT PULSE WIDTH=300µS 0.4 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS CAPACITANCE, pF AMPERES INSTANTANEOUS FORWARD CURRENT, 35 100 60 f=1MHz TJ=25 40 20 10 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE, VOLTS 100