Maxim MAX8794ETB+ Low-voltage ddr linear regulator Datasheet

19-0584; Rev 0; 8/06
KIT
ATION
EVALU
E
L
B
A
IL
AVA
Low-Voltage DDR Linear Regulator
Features
The MAX8794 DDR linear regulator sources and sinks up
to 3A peak (typ) using internal n-channel MOSFETs. This
linear regulator delivers an accurate 0.5V to 1.5V output
from a low-voltage power input (VIN = 1.1V to 3.6V). The
MAX8794 uses a separate 3.3V bias supply to power the
control circuitry and drive the internal n-channel MOSFETs.
The MAX8794 provides current and thermal limits to prevent damage to the linear regulator. Additionally, the
MAX8794 generates a power-good (PGOOD) signal to
indicate that the output is in regulation. During startup,
PGOOD remains low until the output is in regulation for 2ms
(typ). The internal soft-start limits the input surge current.
The MAX8794 powers the active-DDR termination bus
that requires a tracking input reference. The MAX8794
can also be used in low-power chipsets and graphics
processor cores that require dynamically adjustable
output voltages. The MAX8794 is available in a 10-pin,
3mm x 3mm, TDFN package.
♦ Internal Power MOSFETs with Current Limit (3A typ)
Applications
Ordering Information
♦ Fast Load-Transient Response
♦ External Reference Input with Reference
Output Buffer
♦ 1.1V to 3.6V Power Input
♦ ±15mV (max) Load-Regulation Error
♦ Thermal-Fault Protection
♦ Shutdown Input
♦ Power-Good Window Comparator with 2ms (typ)
Delay
♦ Small, Low-Profile, 10-Pin, 3mm x 3mm TDFN
Package
♦ Ceramic or Polymer Output Capacitors
Notebook/Desktop Computers
DDR Memory Termination
Active Termination Buses
PART
TEMP
RANGE
PINPACKAGE
MAX8794ETB+
-40°C to
+85°C
10 TDFN
(3mm x 3mm)
Graphics Processor Core Supplies
Chipset/RAM Supplies as Low as 0.5V
TOP
MARK
PKG
CODE
ABD
T1033-1
+Denotes lead-free package.
Typical Operating Circuit
Pin Configuration
VIN
(1.1V TO 3.6V)
IN
OUT
TOP VIEW
VOUT = VTT
OUTS
+
REFOUT 1
10 IN
VCC 2
AGND
3
VBIAS
(2.7V TO 3.6V)
9 OUT
MAX8794
8 PGND
REFIN 4
7 SHDN
PGOOD 5
6 OUTS
TDFN
3mm x 3mm
MAX8794
VCC
PGND
SHDN
AGND
PGOOD
VDDQ
(2.5V OR 1.8V)
VREFOUT = VTTR
REFIN
REFOUT
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX8794
General Description
MAX8794
Low-Voltage DDR Linear Regulator
ABSOLUTE MAXIMUM RATINGS
IN to PGND............................................................-0.3V to +4.3V
OUT to PGND ..............................................-0.3V to (VIN + 0.3V)
OUTS to AGND ............................................-0.3V to (VIN + 0.3V)
VCC to AGND.........................................................-0.3V to +4.3V
REFIN, REFOUT, SHDN, PGOOD to AGND...-0.3V to (VCC + 0.3V)
PGND to AGND .....................................................-0.3V to +0.3V
REFOUT Short Circuit to AGND .................................Continuous
OUT Continuous RMS Current
100s ................................................................................±1.6A
1s ....................................................................................±2.5A
Continuous Power Dissipation (TA = +70°C)
10-Pin 3mm x 3mm TDFN
(derated 24.4mW/°C above +70°C)...........................1951mW
Operating Temperature Range
MAX8794ETB...................................................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 1.8V, VCC = 3.3V, VREFIN = VOUTS = 1.25V, SHDN = VCC, circuit of Figure 1, TA = -40°C to +85°C, unless otherwise noted.
Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
VIN
Power input
1.1
3.6
VCC
Bias supply
2.7
3.6
Quiescent Supply Current (VCC)
ICC
Load = 0, VREFIN > 0.45V
0.7
Shutdown Supply Current (VCC)
ICC(SHDN)
SHDN = GND, VREFIN > 0.45V
350
600
SHDN = GND, REFIN = GND
50
100
Quiescent Supply Current (VIN)
IIN
Load = 0
0.4
10
mA
Shutdown Supply Current (VIN)
IIN(SHDN)
0.1
10
µA
0
+4
Input Voltage Range
Feedback-Voltage Error
VOUTS
SHDN = GND
REFIN to OUTS,
IOUT = ±200mA
TA = +25°C
-4
TA = -40°C to +85°C
-6
Load-Regulation Error
-1A ≤ IOUT ≤ +1A
Line-Regulation Error
1.4V ≤ VIN ≤ 3.3V, IOUT = ±100mA
OUTS Input Bias Current
IOUTS
1.3
+6
-15
+15
1
V
mA
µA
mV
mV
mV
-1
+1
µA
0.5
1.5
V
OUTPUT
Output Adjust Range
OUT On-Resistance
Output Current Slew Rate
OUT Power-Supply Rejection
Ratio
PSRR
OUT to OUTS Resistance
ROUTS
Discharge MOSFET OnResistance
2
High-side MOSFET (source) (IOUT = 0.1A)
0.10
0.169
Low-side MOSFET (sink) (IOUT = -0.1A)
0.10
0.20
Ω
COUT = 100µF, IOUT = 0.1A to 2A
3
A/µs
10Hz < f < 10kHz, IOUT = 200mA,
COUT = 100µF
80
dB
12
kΩ
8
Ω
RDISCHARGE SHDN = GND
_______________________________________________________________________________________
Low-Voltage DDR Linear Regulator
(VIN = 1.8V, VCC = 3.3V, VREFIN = VOUTS = 1.25V, SHDN = VCC, circuit of Figure 1, TA = -40°C to +85°C, unless otherwise noted.
Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
REFERENCE
REFIN Voltage Range
VREFIN
0.5
1.5
V
REFIN Input Bias Current
IREFIN
-1
+1
µA
0.35
0.45
V
VREFIN
VREFIN
+ 0.01
V
+20
mV
REFIN Undervoltage-Lockout
Voltage
REFOUT Voltage
Rising edge, hysteresis = 75mV
VREFOUT
REFOUT Load Regulation
∆VREFOUT
VCC = 3.3V, IREFOUT = 0
IREFOUT = ±5mA
VREFIN
- 0.01
-20
FAULT DETECTION
Thermal-Shutdown Threshold
TSHDN
Rising edge, hysteresis = 15°C
VCC Undervoltage-Lockout
Threshold
VUVLO
Rising edge, hysteresis = 100mV
IN Undervoltage-Lockout
Threshold
Current-Limit Threshold
Soft-Start Current-Limit Time
+165
2.45
Rising edge, hysteresis = 55mV
ILIMIT
1.8
tSS
°C
2.55
2.65
V
0.9
1.1
V
3
4.2
200
A
µs
INPUTS AND OUTPUTS
PGOOD Lower Trip Threshold
With respect to feedback threshold,
hysteresis = 12mV
-200
-150
-100
mV
PGOOD Upper Trip Threshold
With respect to feedback threshold,
hysteresis = 12mV
100
150
200
mV
5
10
35
µs
2
3.5
ms
0.3
V
1
µA
PGOOD Propagation Delay
tPGOOD
OUTS forced 25mV beyond PGOOD trip
threshold
Startup rising edge, OUTS within ±100mV of
the feedback threshold
PGOOD Startup Delay
PGOOD Output Low Voltage
ISINK = 4mA
PGOOD Leakage Current
OUTS = REFIN (PGOOD high impedance),
PGOOD = VCC + 0.3V
SHDN Logic Input Threshold
SHDN Logic Input Current
IPGOOD
Logic high
2.0
Logic low
0.8
SHDN = VCC or GND
-1
+1
V
µA
Note 1: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed through correlation using statistical-quality-control (SQC) methods.
_______________________________________________________________________________________
3
MAX8794
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(Circuit of Figure 1. TA = +25°C, unless otherwise noted.)
VIN = 1.25V
VOUT (V)
0.90
VIN = 1.5V
1.26
1.24
0.88
VIN = 1.8V
VIN = 1.5V
0.86
1.22
0.84
-2
-1
0
1
2
3
-2
-1
0
1
2
1.5
2.0
2.5
3.0
BIAS CURRENT (ICC)
vs. LOAD CURRENT (IOUT)
0.9
0.8
VOUT = 1.25V
1.0
ICC (mA)
0.6
0.5
0.3
0.4
INPUT UVLO
0
2.0
2.5
3.0
0
3.5
ENTERING
DROPOUT
0.2
0.1
0
VOUT = 0.90V
0.6
DROPOUT
VOUT = 1.25V
0.8
0.4
0.2
1.5
VIN = 1.5V
1.2
0.7
50
1.0
1.4
MAX8794 toc05
MAX8794 toc04
1.0
100
0.5
1.0
1.5
0
2.0
2.5
3.0
3.5
-2
-1
0
VIN (V)
IOUT (A)
POWER GROUND CURRENT (IPGND)
vs. SOURCE LOAD CURRENT (IOUT)
INPUT CURRENT (IIN)
vs. SINK LOAD CURRENT (IOUT)
DROPOUT VOLTAGE
vs. OUTPUT CURRENT
VIN = 1.5V
6
IIN (mA)
ENTERING
DROPOUT
VOUT = 1.25V
4
VOUT = 0.90V
3
VOUT = 1.25V
2
VOUT = 0.90V
0
0.5
1.0
IOUT (A)
1.5
2.0
VOUT = 1.25V
0.20
0.15
VOUT = 0.9V
0.10
0.05
1
0
0.25
DROPOUT VOLTAGE (V)
5
0.15
0.30
MAX8794 toc09
0.20
7
MAX8794 toc07
VIN = 1.5V
2
1
VIN (V)
0.25
4
1.0
3
BIAS CURRENT (ICC)
vs. INPUT VOLTAGE (VIN)
ICC (mA)
IIN (µA)
-3
VOUT = 0.90V
0
DROPOUT VOLTAGE LIMITED
0.5
INPUT CURRENT (IIN)
vs. INPUT VOLTAGE (VIN)
150
0.05
THERMALLY LIMITED
1.0
INPUT VOLTAGE (V)
200
0.10
1.5
IOUT (A)
VOUT = 1.25V
0.5
2.0
IOUT (A)
250
0
VOUT = 1.25V
2.5
0
1.20
-3
MAX8794 toc08
VOUT (V)
0.92
VOUT = 0.9V
MAX8794 toc03
1.28
3.0
MAX8794 toc06
0.94
VREFIN = 1.25V
MAXIMUM OUTPUT CURRENT (A)
VREFIN = 0.9V
MAX8794 toc02
1.30
MAX8794 toc01
0.96
MAXIMUM OUTPUT CURRENT
vs. INPUT VOLTAGE
OUTPUT LOAD REGULATION
OUTPUT LOAD REGULATION
IPGND (mA)
MAX8794
Low-Voltage DDR Linear Regulator
0
-2.0
-1.5
-1.0
IOUT (A)
-0.5
0
0
0.5
1.0
1.5
2.0
OUTPUT CURRENT (A)
_______________________________________________________________________________________
2.5
3.0
Low-Voltage DDR Linear Regulator
REFOUT VOLTAGE ERROR
vs. REFOUT LOAD CURRENT
STARTUP WAVEFORM
15
REFOUT VOLTAGE ERROR (mV)
MAX8794 toc11
MAX8794 toc10
20
5V
SHDN
0V
10
1.25V
5
VOUT
0V
0
-5
4V
-10
PGOOD
-15
0V
-20
-10
-5
0
5
10
500µs/div
REFOUT LOAD CURRENT (mA)
SHUTDOWN WAVEFORM
MAX8794 toc12
RLOAD = 100Ω
SOURCE LOAD TRANSIENT
MAX8794 toc13
5V
SHDN
0V
2V
VOUT
AC-COUPLED
1mV/div
1V
VOUT
0V
4V
PGOOD
1A
0V
IOUT
0A
100µs/div
20.0µs/div
LINE TRANSIENT
SOURCE/SINK LOAD TRANSIENT
MAX8794 toc15
MAX8794 toc14
3.3V
VIN (1V/div)
VOUT
AC-COUPLED
5mV/div
1.5V
+1.5A
IOUT
VOUT (10mV/div)
AC-COUPLED
0.9V
-1.5A
IOUT = 100mA
4.00µs/div
40µs/div
_______________________________________________________________________________________
5
MAX8794
Typical Operating Characteristics (continued)
(Circuit of Figure 1. TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Circuit of Figure 1. TA = +25°C, unless otherwise noted.)
DYNAMIC OUTPUT-VOLTAGE TRANSIENT
DYNAMIC OUTPUT-VOLTAGE TRANSIENT
MAX8794 toc16
MAX8794 toc17
VDDQ
1.8V
1.2V
VREFOUT
1.2V
VREFOUT
0.9V
1.2V
0.9V
1.2V
VOUT
VOUT
0.9V
0.9V
20.0µs/div
SINK CURRENT-LIMIT
DISTRIBUTION
SOURCE CURRENT-LIMIT
DISTRIBUTION
+25°C
+85°C
SAMPLE SIZE = 200
SAMPLE PERCENTAGE (%)
40
50
MAX8794 toc18
SAMPLE SIZE = 200
30
20
2.5V
VDDQ
1.8V
20.0µs/div
50
+25°C
+85°C
40
30
20
10
10
0
0
-4.0
-3.5
-3.0
-2.5
SINK CURRENT LIMIT (A)
6
VIN = 1.8V
2.5V
MAX8794 toc19
VIN = 1.5V
SAMPLE PERCENTAGE (%)
MAX8794
Low-Voltage DDR Linear Regulator
-2.0
2.0
2.5
3.0
3.5
4.0
SOURCE CURRENT LIMIT (A)
_______________________________________________________________________________________
Low-Voltage DDR Linear Regulator
PIN
NAME
FUNCTION
1
REFOUT
2
VCC
3
AGND
Analog Ground. Connect the backside pad to AGND.
4
REFIN
External Reference Input. REFIN sets the output regulation voltage (VOUTS = VREFIN).
5
PGOOD
6
OUTS
Output Sense Input. The OUTS regulation level is set by the voltage at REFIN. Connect OUTS to the
remote DDR termination bypass capacitors. OUTS is internally connected to OUT through a 12kΩ
resistor.
7
SHDN
Shutdown Control Input. Connect to VCC for normal operation. Connect to analog ground to shut down the
linear regulator. The reference buffer remains active in shutdown.
8
PGND
Power Ground. Internally connected to the output sink MOSFET.
9
OUT
10
IN
Buffered Reference Output. The output of the unity-gain reference input buffer sources and sinks over
5mA. Bypass REFOUT to AGND with a 0.33µF or greater ceramic capacitor.
Analog Supply Input. Connect to the system supply voltage (+3.3V). Bypass VCC to AGND with a 1µF or
greater ceramic capacitor.
Open-Drain Power-Good Output. PGOOD is low when the output voltage is more than 150mV (typ) above
or below the regulation point, during soft-start, and when shut down. 2ms after the output reaches the
regulation voltage during startup, PGOOD becomes high impedance.
Output of the Linear Regulator
Power Input. Internally connected to the output source MOSFET.
_______________________________________________________________________________________
7
MAX8794
Pin Description
MAX8794
Low-Voltage DDR Linear Regulator
Detailed Description
The MAX8794 is a low-voltage, low-dropout DDR termination linear regulator with an external bias supply
input and a buffered reference output (see Figures 1
and 2). VCC is powered by a 2.7V to 3.6V supply that is
commonly available in laptop and desktop computers.
The 3.3V bias supply drives the gate of the internal
pass transistor, while a lower voltage input at the drain
of the transistor (IN) is regulated to provide VOUT. By
using separate bias and power inputs, the MAX8794
can drive an n-channel high-side MOSFET and use a
lower input voltage to provide better efficiency.
The MAX8794 regulates its output voltage to the voltage at REFIN. When used in DDR applications as a termination supply, the MAX8794 delivers 1.25V or 0.9V at
3A peak (typ) from an input voltage of 1.1V to 3.6V. The
MAX8794 sinks up to 3A peak (typ) as required in a termination supply. The MAX8794 provides shoot-through
protection, ensuring that the source and sink MOSFETs
do not conduct at the same time, yet produces a fast
source-to-sink load transient.
3.3V BIAS
SUPPLY
ON
IN
OUT
COUT1
100µF
CIN2
10µF
MAX8794
3.3V BIAS
SUPPLY
PGND
VCC
R3
100kΩ
C1
1.0µF
AGND
POWER-GOOD
PGOOD
OUTS
ON
OFF
SHDN
R1
10kΩ
VDDQ
REFIN
R2
10kΩ
REFOUT
CREFIN
1000pF
VREFOUT = VTTR
CREFOUT
0.33µF
Figure 1. Standard Application Circuit
VCC
EN
UVLO
OFF
VOUT = VTT = VDDQ / 2
VIN =
1.1V TO 3.6V
SOFTSTART
IN
INPUT
1.1V TO 3.6V
SHDN
THERMAL
SHDN
REFIN
VDDQ
OUT
Gm
PGND
VTTR
12kΩ
REFOUT
OUTS
REFIN
+150mV
AGND
EN
8Ω
REFIN
-150mV
POWERGOOD
PGOOD
DELAY
LOGIC
MAX8794
Figure 2. Functional Diagram
8
_______________________________________________________________________________________
VTT
Low-Voltage DDR Linear Regulator
3.3V Bias Supply (VCC)
The VCC input powers the control circuitry and provides
the gate drive to the pass transistor. This improves efficiency by allowing VIN to be powered from a lower supply voltage. Power V CC from a well-regulated 3.3V
supply. Current drawn from the VCC supply remains relatively constant with variations in VIN and load current.
Bypass VCC with a 1µF or greater ceramic capacitor as
close to the device as possible.
VCC Undervoltage Lockout (UVLO)
The VCC input UVLO circuitry ensures that the regulator
starts up with adequate voltage for the gate-drive circuitry to bias the internal pass transistor. The UVLO
threshold is 2.55V (typ). VCC must remain above this
level for proper operation.
Power-Supply Input (IN)
IN provides the source current for the linear regulator’s
output, OUT. IN connects to the drain of the internal
n-channel power MOSFET. IN can be as low as 1.1V,
minimizing power dissipation. The input UVLO prohibits
operation below 0.8V (typ). Bypass IN with a 10µF or
greater capacitor as close to the device as possible.
Reference Input (REFIN)
The MAX8794 regulates OUTS to the voltage set at
REFIN, making the MAX8794 ideal for memory applications where the termination supply must track the supply voltage. Typically, REFIN is set by an external
resistive voltage-divider connected to the memory supply (VDDQ) as shown in Figure 1.
The maximum output voltage of 1.5V is limited by the
gate-drive voltage of the internal n-channel power
transistor.
Buffered Reference Output (REFOUT)
REFOUT is a unity-gain transconductance amplifier that
generates the DDR reference supply. It sources and
sinks greater than 5mA. The reference buffer is typically
connected to ceramic bypass capacitors (0.33µF to
1.0µF). REFOUT is active when VREFIN > 0.45V and
VCC is above VUVLO. REFOUT is independent of SHDN.
Shutdown
Drive SHDN low to disable the error amplifier, gatedrive circuitry, and pass transistor (Figure 2). In shutdown, OUT is terminated to GND with an 8Ω MOSFET.
REFOUT is independent of SHDN. Connect SHDN to
VCC for normal operation.
Current Limit
The MAX8794 features source and sink current limits to
protect the internal n-channel MOSFETs. The sourceand-sink MOSFETs have a typical 3A current limit (1.8A
min). This current limit prevents damage to the internal
power transistors, but the device can enter thermal
shutdown if the power dissipation increases the die
temperature above +165°C (see the Thermal-Overload
Protection section).
Soft-Start Current Limit
Soft-start gradually increases the internal source current
limit to reduce input surge currents at startup. Fullsource current limit is available after the 200µs soft-start
timer has expired. The soft-start current limit is given by:
I
× t
ILIMIT(SS) = LIMIT
t SS
where ILIMIT and tSS are from the Electrical Characteristics. Figure 3 shows the MAX8794 PGOOD and
soft-start waveform.
Thermal-Overload Protection
Thermal-overload protection prevents the linear regulator
from overheating. When the junction temperature
exceeds +165°C, the linear regulator and reference
buffer are disabled, allowing the device to cool. Normal
operation resumes once the junction temperature cools
by 15°C. Continuous short-circuit conditions result in a
pulsed output until the overload is removed. A continuous
thermal-overload condition results in a pulsed output. For
continuous operation, do not exceed the absolute maximum junction-temperature rating of +150°C.
_______________________________________________________________________________________
9
MAX8794
The MAX8794 features an open-drain PGOOD output
that transitions high 2ms after the output initially reaches regulation. PGOOD goes low within 10µs of when
the output goes out of regulation by ±150mV. The
MAX8794 features current- and thermal-limiting circuitry
to prevent damage during fault conditions.
MAX8794
Low-Voltage DDR Linear Regulator
SHDN
200µs
CURRENT LIMIT
OUTPUT OVERLOAD
CONDITION
POWER-GOOD
WINDOW
OUT
2ms STARTUP
DELAY
PGOOD
10µs
PROPAGATION
DELAY
10µs
PROPAGATION
DELAY
Figure 3. MAX8794 PGOOD and Soft-Start Waveforms
Power-Good (PGOOD)
The MAX8794 provides an open-drain PGOOD output
that goes high 2ms (typ) after the output initially reaches regulation during startup. PGOOD transitions low
10µs after the output goes out of regulation by ±150mV,
or when the device enters shutdown. Connect a pullup
resistor from PGOOD to VCC for a logic-level output.
Use a 100kΩ resistor to minimize current consumption.
REFERENCE
VOLTAGE
(VREF)
R1
MAX8794
CREFIN
Applications Information
REFIN
Dynamic Output-Voltage Transitions
By changing the voltage at REFIN, the MAX8794 can
be used in applications that require dynamic outputvoltage changes between two set points (graphics
processors). Figure 4 shows a dynamically adjustable
resistive voltage-divider network at REFIN. Using an
external signal MOSFET, a resistor can be switched in
and out of the REFIN resistor-divider, changing the voltage at REFIN. The two output voltages are determined
by the following equations:
⎛ R2 ⎞
VOUT(LOW) = VREF ⎜
⎟
⎝ R1 + R2 ⎠
⎡ (R2 + R3) ⎤
VOUT(HIGH) = VREF ⎢
⎥
⎢⎣ R1 + (R2 + R3) ⎥⎦
10
R2
VOUT(LOW)
VOUT(HIGH)
VOUT(LOW) = VREF
R3
( )
VOUT(HIGH) = VREF
R2
R1 + R2
(R2 + R3)
R1 + (R2 + R3)
Figure 4. Dynamic Output-Voltage Change
______________________________________________________________________________________
Low-Voltage DDR Linear Regulator
PDIS(MAX) =
TJ(MAX) - TA
θJC + θCA
where TJ(MAX) is the maximum junction temperature
(+150°C), TA is the ambient temperature, θJC is the
thermal resistance from the die junction to the package
case, and θCA is the thermal resistance from the case
through the PC board, copper traces, and other materials to the surrounding air. For optimum power dissipation, use a large ground plane with good thermal
contact to the backside pad, and use wide input and
output traces.
When 1in2 of copper is connected to the device, the
maximum allowable power dissipation of a 10-pin TDFN
package is 1951mW. The maximum power dissipation is
derated by 24.4mW/°C above TA = +70°C. Extra copper
on the PC board increases thermal mass and reduces
thermal resistance of the board. Refer to the MAX8794
evaluation kit for a layout example.
The MAX8794 delivers up to 3A and operates with input
voltages up to 3.6V, but not simultaneously. High output
currents can only be achieved when the input-output
differential voltages are low (Figure 5).
Dropout Operation
A regulator’s minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. Because the MAX8794 uses an n-channel
pass transistor, the dropout voltage is a function of the
drain-to-source on-resistance (RDS(ON) = 0.25Ω max)
multiplied by the load current (see the Typical
Operating Characteristics):
SAFE OPERATING REGION
3.5
MAXIMUM OUTPUT CURRENT (A)
Operating Region and Power Dissipation
The maximum power dissipation of the MAX8794
depends on the thermal resistance of the 10-pin TDFN
package and the circuit board, the temperature difference between the die and ambient air, and the rate of
airflow. The power dissipated in the device is:
PSRC = ISRC x (VIN – VOUT)
PSINK = ISINK x VOUT
The resulting maximum power dissipation is:
MAX8794
For a step-voltage change at REFIN, the rate of change
of the output voltage is limited by the total output
capacitance, the current limit, and the load during the
transition. Adding a capacitor across REFIN and AGND
filters noise and controls the rate of change of the
REFIN voltage during dynamic transitions. With the
additional capacitance, the REFIN voltage slews
between the two set points with a time constant given
by REQ x CREFIN, where REQ is the equivalent parallel
resistance seen by the slew capacitor.
DROPOUT VOLTAGE
LIMITED
MAXIMUM CURRENT LIMIT
3.0
2.5
2.0
TA = 0°C TO +70°C
1.5
VIN(MAX) - VOUT(MIN)
1.0
0.5
TA = +100°C
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
INPUT-OUTPUT DIFFERENTIAL VOLTAGE (V)
Figure 5. Power Operating Region—Maximum Output Current
vs. Input-Output Differential Voltage
VDROPOUT = RDS(ON) x IOUT
For low output-voltage applications, the sink current is
limited by the output voltage and the RDS(ON) of the
MOSFET.
Input Capacitor Selection
Bypass IN to PGND with a 10µF or greater ceramic
capacitor. Bypass VCC to AGND with a 1µF ceramic
capacitor for normal operation in most applications.
Typically, the LDO is powered from the output of a
step-down controller (memory supply) that has additional bulk capacitance (polymer or tantalum) and distributed ceramic capacitors.
Output Capacitor Selection
The MAX8794 output stability is independent of the output capacitance for C OUT from 10µF to 220µF.
Capacitor ESR between 2mΩ and 50mΩ is needed to
maintain stability. Within the recommended capacitance and ESR limits, the output capacitor should be
chosen to provide good transient response:
∆IOUT(P-P) x ESR = ∆VOUT(P-P)
where ∆IOUT(P-P) is the maximum peak-to-peak loadcurrent step (typically equal to the maximum source
load plus the maximum sink load), and ∆VOUT(P-P) is
the allowable peak-to-peak voltage tolerance.
Using larger output capacitance can improve efficiency
in applications where the source and sink currents
change rapidly. The capacitor acts as a reservoir for
the rapid source and sink currents, so no extra current
is supplied by the MAX8794 or discharged to ground,
improving efficiency.
______________________________________________________________________________________
11
MAX8794
Low-Voltage DDR Linear Regulator
Noise, PSRR, and Transient Response
PC Board Layout Guidelines
The MAX8794 operates with low-dropout voltage and
low quiescent current in notebook computers while
maintaining good noise, transient response, and ACrejection specifications. Improved supply-noise rejection and transient response can be achieved by
increasing the values of the input and output capacitors. Use passive filtering techniques when operating
from noisy sources.
The MAX8794 load-transient response graphs (see the
Typical Operating Characteristics) show two components of the output response: a DC shift from the output
impedance due to the load-current change and the
transient response. A typical transient response for a
step change in the load current from -1.5A to +1.5A is
10mV. Increasing the output capacitor’s value and
decreasing the ESR attenuate the overshoot.
The MAX8794 requires proper layout to achieve the
intended output power level and low noise. Proper layout involves the use of a ground plane, appropriate
component placement, and correct routing of traces
using appropriate trace widths. Refer to the MAX8794
evaluation kit for a layout example:
1) Minimize high-current ground loops. Connect the
ground of the device, the input capacitor, and the
output capacitor together at one point.
2) To optimize performance, a ground plane is essential. Use all available copper layers in applications
where the device is located on a multilayer board.
3) Connect the input filter capacitor less than 10mm
from IN. The connecting copper trace carries large
currents and must be at least 2mm wide, preferably
5mm wide.
4) Connect the backside pad to a large ground plane.
Use as much copper as necessary to decrease the
thermal resistance of the device. In general, more
copper provides better heatsinking capabilities.
Chip Information
TRANSISTOR COUNT: 3496
PROCESS: BiCMOS
12
______________________________________________________________________________________
Low-Voltage DDR Linear Regulator
6, 8, &10L, DFN THIN.EPS
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
21-0137
COMMON DIMENSIONS
MIN.
MAX.
PKG. CODE
N
D2
E2
e
JEDEC SPEC
b
A
0.70
0.80
T633-1
6
1.50±0.10
2.30±0.10
0.95 BSC
MO229 / WEEA
0.40±0.05
1.90 REF
D
2.90
3.10
T633-2
6
1.50±0.10
2.30±0.10
0.95 BSC
MO229 / WEEA
0.40±0.05
1.90 REF
E
2.90
3.10
T833-1
8
1.50±0.10
2.30±0.10
0.65 BSC
MO229 / WEEC
0.30±0.05
1.95 REF
A1
0.00
0.05
T833-2
8
1.50±0.10
2.30±0.10
0.65 BSC
MO229 / WEEC
0.30±0.05
1.95 REF
0.40
T833-3
8
1.50±0.10
2.30±0.10
0.65 BSC
MO229 / WEEC
0.30±0.05
1.95 REF
2.30±0.10
0.50 BSC
MO229 / WEED-3
0.25±0.05
2.00 REF
2.00 REF
0.20
1
2
PACKAGE VARIATIONS
SYMBOL
L
H
[(N/2)-1] x e
k
0.25 MIN.
T1033-1
10
1.50±0.10
A2
0.20 REF.
T1033-2
10
1.50±0.10
2.30±0.10
0.50 BSC
MO229 / WEED-3
0.25±0.05
T1433-1
14
1.70±0.10
2.30±0.10
0.40 BSC
----
0.20±0.05
2.40 REF
T1433-2
14
1.70±0.10
2.30±0.10
0.40 BSC
----
0.20±0.05
2.40 REF
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
-DRAWING NOT TO SCALE-
21-0137
H
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
MAX8794
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Similar pages