Taiyo Yuden LB3218T100 Wire-wound chip inductors (lb series) Datasheet

Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called“TAIYO YUDEN’
s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
12
notice_e-01
WIRE-WOUND CHIP INDUCTORS (LB SERIES)
REFLOW
■ FEATURES
■ APPLICATIONS
LB-series are Wound Chip Inductors having wide line-up, which are suitable
for any circuit designs.
◦They are suitable for an anti-noise measure on the power supply circuit
of DSC, DVC, HDD, LCD-TV, mobile phones,PC, game equipments,
various communication equipments and etc..
◦LBC series has large rated current. They contribute to the miniaturization of the power supply circuit.
■ OPERATING TEMP.
◦LBR series has low DC resistance. They contribute to the miniaturization of the power supply circuit.
◦－ 40 ～ 105℃（Including-self-generated heat）
◦LBMF series has a low loss characteristic.
■ ORDERING CODE
B △
L
❶
LB
2
1
❷
2
T
❸
❶Type
Wound chip inductor
△
C
R
MF
0
0
❹
❸External Dimensions
〔mm〕
1608
（0603） 1.6×0.8
2012
（0805） 2.0×1.25
2016
（0806） 2.0×1.6
2518
（1007） 2.5×1.8
3218
（1207） 3.2×1.8
3225
（1210） 3.2×2.5
❷Shape
Standard products
High current
Low Rdc
Low loss
1
T
△ △ △ △ △
0
❺
❹Packaging
Tape & Reel
❻
❺Nominal
Inductance〔μH〕
example
1R0
1
100
10
101
100
※R=decimal point
❼
❻Inductance
Tolerances〔％〕
K
±10
M
±20
❽
❼Special
code
Standard
△
products
Low Rdc
R
type
❽Internal code
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
EXTERNAL DIMENSIONS
Type
C
A
TYPE
1608
MF1608
2012
2016
2518
3218
3225
A
0.55
0.55
0.60
0.60
0.60
0.85
0.85
B
0.7
0.7
1.0
1.0
1.5
1.7
1.7
Unit：mm
C
0.9
1.0
1.45
1.8
2.0
2.0
2.7
B
L
T
Standard Quantity [pcs]
Paper
Embossed
Tape
Tape
e
LB1608
1.6±0.1
0.8±0.1
0.8±0.1
0.35±0.15
（0.063±0.004） （0.031±0.004） （0.031±0.004） （0.014±0.006）
4000
－
LBMF1608
1.6±0.2
0.8±0.2
0.8±0.2
0.45±0.15
（0.063±0.008） （0.031±0.008） （0.031±0.008） （0.016±0.006）
－
3000
LB2012
LBC2012
LBR2012
2.0±0.2
1.25±0.2
1.25±0.2
0.5±0.2
（0.079±0.008） （0.049±0.008） （0.049±0.008） （0.020±0.008）
－
3000
LB2016
LBC2016
2.0±0.2
1.6±0.2
1.6±0.2
0.5±0.2
（0.079±0.008） （0.063±0.008） （0.063±0.008） （0.020±0.008）
－
2000
LB2518
LBC2518
LBR2518
2.5±0.2
1.8±0.2
1.8±0.2
0.5±0.2
（0.098±0.008） （0.071±0.008） （0.071±0.008） （0.020±0.008）
－
2000
LB3218
3.2±0.2
1.8±0.2
1.8±0.2
0.6±0.2
（0.128±0.008） （0.071±0.008） （0.071±0.008） （0.024±0.008）
－
2000
LBC3225
3.2±0.2
2.5±0.2
2.5±0.2
0.6±0.3
（0.128±0.008） （0.098±0.008） （0.098±0.008） （0.024±0.012）
－
A
Surface Mounting
・ Mounting and soldering conditions should be checked
beforehand.
・ Applicable soldering process
to those products is reflow
soldering only.
・ Recommended Land Patterns
W
1000
Unit：mm
（inch）
■ AVAILABLE INDUCTANCE RANGE
Type
Range
LB1608
LBMF1608
LB2012
LBC2012
LBR2012
LB2016
LBC2016
LB2518
LBC2518
LBR2518
LB3218
LBC3225
Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］ Imax.［mA］ Rdc±30％［Ω］
Inductance［μH］
1
160 1μH 0.17 230 1μH 0.09 405 1μH 0.15 620 1μH 0.19 400 1μH 0.07 490 1μH 0.09 690 1μH
70
10
665 1μH 0.06 775 1μH 0.08 960 1μH 0.045 1075 1μH 0.06 1100 1μH 0.055
0.55
60
0.7
10μH
80
0.36 120
35
0.7
2.5
47μH
100
0.1
200
1.2
90
45
7.0
100μH
150
0.36 155
0.5
245
0.82 165
50
40
4.5
100μH
75
60
0.25 375
0.36 235
2.1
125
3.70
45
28.0
0.19 340
0.25 540
0.133
5.8
47μH
4.0
100μH
8.0
100μH
15
24
1000μH
1000
680μH
80
1.89 140
100μH
2.40 150
1.4
100μH
39
27
1000μH
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
80
12
wound01_e-02
■ PART NUMBERS
●1608
（0603）TYPE
Ordering code
LB 1608T1R0M
LB 1608T2R2M
LB 1608T4R7M
LB 1608T8R2M
LB 1608T100M
Ordering code
RoHS
RoHS
RoHS
RoHS
RoHS
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
2.2
4.7
8.2
10
Inductance
Tolerance
Inductance
〔μH〕
1.0
2.2
3.3
4.7
10
22
47
Inductance
Tolerance
±20%
±20%
±10%
±20%
Self-resonant frequency
〔MHz〕min.
100
80
45
32
32
DC Resistance
〔Ω〕
（±30％）
0.17
0.33
0.55
0.70
0.70
Rated current
〔mA〕max.
160
115
70
60
60
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
80
60
45
32
16
11
DC Resistance
〔Ω〕
（±30％）
0.09
0.17
0.22
0.24
0.36
1.0
2.5
Rated current
〔mA〕max.
230
160
130
110
80
50
35
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
80
55
45
38
32
32
28
16
11
10
8
DC Resistance
〔Ω〕
（±30％）
0.15
0.23
0.30
0.40
0.47
0.70
0.50
1.3
1.7
3.7
6.0
7.0
Rated current
〔mA〕max.
405
260
235
190
135
120
120
100
80
60
50
45
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
70
45
40
16
11
DC Resistance
〔Ω〕
（±30％）
0.19
0.33
0.50
1.2
3.7
5.8
Rated current
〔mA〕max.
620
430
295
200
130
90
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
80
45
32
16
11
8
DC Resistance
〔Ω〕
（±30％）
0.07
0.13
0.24
0.36
1.0
1.7
4.0
Rated current
〔mA〕max.
400
260
200
150
100
75
50
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
80
70
55
45
38
32
28
16
14
11
10
8
DC Resistance
〔Ω〕
（±30％）
0.09
0.11
0.13
0.20
0.25
0.35
0.50
0.70
1.0
1.7
2.4
3.0
4.5
Rated current
〔mA〕max.
490
380
375
285
225
200
155
130
105
85
70
55
40
Measuring frequency
〔MHz〕
7.96
2.52
7.96
2.52
・□Please specify the Inductance tolerance code
（K or M）
●2012
（0805）TYPE
Ordering code
LB 2012T1R0M
LB 2012T2R2M
LB 2012T3R3M
LB 2012T4R7M
LB 2012T6R8M
LB 2012T100□
LB 2012T100□R
LB 2012T150□
LB 2012T220□
LB 2012T470□
LB 2012T680□
LB 2012T101□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
2.2
3.3
4.7
6.8
10
10
15
22
47
68
100
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
Ordering code
LB C2012T1R0M
LB C2012T2R2M
LB C2012T4R7M
LB C2012T100□
LB C2012T220□
LB C2012T470□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
2.2
4.7
10
22
47
Inductance
Tolerance
±20%
±10%
±20%
／ STANDARD INDUCTORS
INDUCTORS
LBMF1608T1R0M
LBMF1608T2R2M
LBMF1608T3R3M
LBMF1608T4R7M
LBMF1608T100□
LBMF1608T220□
LBMF1608T470□
EHS
7.96
2.52
・□Please specify the Inductance tolerance code
（K or M）
Ordering code
LB R2012T1R0M
LB R2012T2R2M
LB R2012T4R7M
LB R2012T100□
LB R2012T220□
LB R2012T470□
LB R2012T101□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
2.2
4.7
10
22
47
100
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
●2016
（0806）
TYPE
Ordering code
LB 2016T1R0M
LB 2016T1R5M
LB 2016T2R2M
LB 2016T3R3M
LB 2016T4R7M
LB 2016T6R8M
LB 2016T100□
LB 2016T150□
LB 2016T220□
LB 2016T330□
LB 2016T470□
LB 2016T680□
LB 2016T101□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound01_e-02
12
81
■ PART NUMBERS
Ordering code
LB C2016T1R0M
LB C2016T1R5M
LB C2016T2R2M
LB C2016T3R3M
LB C2016T4R7M
LB C2016T6R8M
LB C2016T100□
LB C2016T150□
LB C2016T220□
LB C2016T330□
LB C2016T470□
LB C2016T680□
LB C2016T101□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
Inductance
Tolerance
±20%
±10%
±20%
Self-resonant frequency
〔MHz〕min.
100
80
70
55
45
38
32
28
16
14
11
10
8
DC Resistance
〔Ω〕
（±30％）
0.10
0.15
0.20
0.27
0.37
0.59
0.82
1.2
1.8
2.8
4.3
7.0
8.0
Rated current
〔mA〕max.
690
600
520
410
355
290
245
200
165
135
110
95
75
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
80
68
54
46
46
38
30
23
19
15
12
9.5
9.0
7.0
5.5
4.5
3.5
3.0
2.4
DC Resistance
〔Ω〕
（±30％）
0.06
0.07
0.09
0.11
0.13
0.10
0.15
0.25
0.32
0.50
0.70
0.95
1.5
2.1
3.2
4.5
7.0
10
17
24
Rated current
〔mA〕max.
665
405
340
280
240
235
195
165
145
115
95
85
70
60
45
40
30
25
20
15
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
100
80
68
54
41
38
30
23
19
15
12
9.5
9.0
7.0
5.5
4.5
3.5
3.0
DC Resistance
〔Ω〕
（±30％）
0.080
0.065
0.11
0.13
0.16
0.20
0.30
0.36
0.65
0.77
1.5
1.9
2.8
3.7
6.1
8.4
12.3
22
28
Rated current
〔mA〕max.
775
890
730
630
560
510
420
375
285
250
185
165
140
125
95
80
65
50
45
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
100
68
45
30
19
11
9
DC Resistance
〔Ω〕
（±30％）
0.045
0.07
0.10
0.19
0.44
0.84
1.89
Rated current
〔mA〕max.
960
480
345
235
175
120
80
Measuring frequency
〔MHz〕
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
●2518
（1007）TYPE
Ordering code
LB 2518T1R0M
LB 2518T1R5M
LB 2518T2R2M
LB 2518T3R3M
LB 2518T4R7M
LB 2518T4R7MR
LB 2518T6R8M
LB 2518T100□
LB 2518T150□
LB 2518T220□
LB 2518T330□
LB 2518T470□
LB 2518T680□
LB 2518T101□
LB 2518T151□
LB 2518T221□
LB 2518T331□
LB 2518T471□
LB 2518T681□
LB 2518T102□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.5
2.2
3.3
4.7
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
1000
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
0.252
・□Please specify the Inductance tolerance code
（K or M）
Ordering code
LB C2518T1R0M
LB C2518T1R0MR
LB C2518T1R5M
LB C2518T2R2M
LB C2518T3R3M
LB C2518T4R7M
LB C2518T6R8M
LB C2518T100□
LB C2518T150□
LB C2518T220□
LB C2518T330□
LB C2518T470□
LB C2518T680□
LB C2518T101□
LB C2518T151□
LB C2518T221□
LB C2518T331□
LB C2518T471□
LB C2518T681□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
Ordering code
LB R2518T1R0M
LB R2518T2R2M
LB R2518T4R7M
LB R2518T100□
LB R2518T220□
LB R2518T470□
LB R2518T101□
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
2.2
4.7
10
22
47
100
Inductance
Tolerance
±20%
±10%
±20%
7.96
2.52
0.796
・□Please specify the Inductance tolerance code
（K or M）
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
82
12
wound01_e-02
■ PART NUMBERS
●3218
（1297）TYPE
Ordering code
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
1000
Inductance
Tolerance
±20%
±10%
±20%
Self-resonant frequency
〔MHz〕min.
100
80
68
54
41
40
30
25
19
15
12
11
8
7
5
4
3.5
3.0
2.4
DC Resistance
〔Ω〕
（±30％）
0.06
0.07
0.09
0.11
0.13
0.17
0.25
0.32
0.49
0.75
0.92
1.49
2.4
3.2
5.4
7.0
14
17
27
Rated current
〔mA〕max.
1075
860
775
560
550
380
340
300
255
215
205
145
140
105
80
65
54
45
39
Measuring frequency
〔MHz〕
Self-resonant frequency
〔MHz〕min.
250
220
190
160
70
50
23
20
17
13
10
8
6
DC Resistance
〔Ω〕
（±30％）
0.055
0.060
0.080
0.095
0.100
0.120
0.133
0.195
0.27
0.41
0.67
1.0
1.4
Rated current
〔mA〕max.
1100
1000
930
820
680
620
540
420
330
300
220
190
150
Measuring frequency
〔MHz〕
7.96
2.52
0.796
0.252
・□Please specify the Inductance tolerance code
（K or M）
●3225
（1210）TYPE
Ordering code
LB C3225T1R0MR
LB C3225T1R5MR
LB C3225T2R2MR
LB C3225T3R3MR
LB C3225T4R7MR
LB C3225T6R8MR
LB C3225T100□R
LB C3225T150□R
LB C3225T220□R
LB C3225T330□R
LB C3225T470□R
LB C3225T680□R
LB C3225T101□R
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Inductance
〔μH〕
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
Inductance
Tolerance
±20%
±10%
±20%
0.1
／ STANDARD INDUCTORS
INDUCTORS
LB 3218T1R0M
LB 3218T1R5M
LB 3218T2R2M
LB 3218T3R3M
LB 3218T4R7M
LB 3218T6R8M
LB 3218T100□
LB 3218T150□
LB 3218T220□
LB 3218T330□
LB 3218T470□
LB 3218T680□
LB 3218T101□
LB 3218T151□
LB 3218T221□
LB 3218T331□
LB 3218T471□
LB 3218T681□
LB 3218T102□
EHS
・□Please specify the Inductance tolerance code
（K or M）
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound01_e-02
12
83
■ ELECTRICAL CHARACTERISTICS
■DC Bias characteristics（Measured by HP4285A＋42841A）
LBMF1608
LB2012
10
10
100
DC Bias 〔mA〕
1
0.1
1000
1
10
100
DC Bias 〔mA〕
LBR2012
10
101□
100□
100
1000
DC Bias 〔mA〕
101□
100
100□
10
1R0M
1
0.1
10000
100□
10
1
10
100
DC Bias 〔mA〕
LBC2016
Inductance 〔μH〕
Inductance 〔μH〕
Inductance 〔μH〕
1
1R0M
1
1000
LB2518
1000
1000
10
1R0M
1
LB2016
1000
100
100□
10
0.1
1000
101□
100
1000
101□
100
100□
10
1R0M
1
Inductance 〔μH〕
1
1R0M
Inductance 〔μH〕
1R0M
1
0.1
Inductance 〔μH〕
Inductance 〔μH〕
100M
100
470□
4R7M
10
LBC2012
1000
100□
Inductance 〔μH〕
LB1608
100
101□
100
100□
10
1R0M
1
1R0M
10
100
DC Bias 〔mA〕
0.1
1000
1
10
101□
100
100□
10
1R0M
1
1
10
1
10
100
1000
DC Bias 〔mA〕
10000
0.1
10000
101□
100□
10
1R0M
1
1
10
1
10
100
1000
DC Bias 〔mA〕
10000
100
10000
101□Ｒ
101□
100
100□
10
1R0M
1
0.1
100
1000
DC Bias 〔mA〕
ＬＢＣ3225
1000
100
0.1
100
1000
DC Bias 〔mA〕
LB3218
1000
Inductance 〔μH〕
Inductance 〔μH〕
0.1
10000
LBR2518
LBC2518
1000
0.1
100
1000
DC Bias 〔mA〕
1
10
100
1000
DC Bias 〔mA〕
10000
Inductance 〔μH〕
1
Inductance 〔μH〕
1
100□Ｒ
10
1R0MR
1
0.1
1
10
100
1000
DC Bias 〔mA〕
10000
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
84
12
wound01_e-02
／ STANDARD INDUCTORS
INDUCTORS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound01_e-02
12
85
■ PACKAGING
①Minimum Quantity
④Leader and Blank Portion
Type
LBC3225/CBC3225
LB3218
LBR2518/LBC2518/LB251
/CB2518/CBC2518/LEM2520
LBM2016/LBC2016/
LB2016/CB2016/CBC2016
LB2012/LBC2012/LBR202
/CB2012/CBC2012
CBL2012
LB1608
LBMF1608/CBMF1608
Standard Quantity［pcs］
Papar Tape
Embossed Tape
ー
1000
ー
2000
ー
2000
ー
2000
ー
3000
4000
4000
ー
ー
ー
3000
(10 pitches or more)
(10 pitches or more) 150mm or more
(5.9 inches or more)
⑤Reel Size
＋0.039
φ60 ＋1
)
−0（φ2.36 −0
◦Embossed tape
φ180 ＋0
（φ7.09 ＋0
−3
−0.118 )
2.5 max
（0.098）
②Tape material
10.0±1.5
(0.394±0.059)
⑥Top Tape Strength
The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as
illustrated below.
Pull direction
③Taping Dimensions
◦Embossed Tape（0.315 inches wide）
◦Card board carrier tape（0.315 inches wide）
Chip cavity
Type
LBM 2016
LEM 2520
LBC3225/
CBC3225
LB3218
A
Insertion pitch
B
F
Tape thickness
T
K
2.1±0.1
4.0±0.1
0.3±0.05
1.9max.
1.75±0.1
（0.069±0.004）（0.083±0.004）（0.157±0.004）（0.012±0.002） （0.075max.）
2.7±0.1
4.0±0.1
0.3±0.05
2.1±0.1
2.3±0.1
（0.091±0.004） （0.106±0.004）（0.157±0.004）（0.012±0.002）（0.083±0.004）
2.8±0.1
3.5±0.1
4.0±0.1
0.3±0.05
4.0max.
（0.110±0.004）（0.138±0.004）（0.157±0.004）（0.012±0.002） （0.157max.）
3.5±0.1
4.0±0.1
0.3±0.05
2.2max.
2.1±0.1
（0.083±0.004） （0.138±0.004）（0.157±0.004）（0.012±0.002） （0.087max.）
LB2518 / CB2518
2.15±0.1
2.7±0.1
4.0±0.1
0.3±0.05
2.2max.
LBC2518 / CBC2518
（0.085±0.004） （0.106±0.004）（0.157±0.004）（0.012±0.002） （0.087max.）
LBR2518
LB2016/ CB2016
1.75±0.1
2.1±0.1
4.0±0.1
0.3±0.05
1.9max.
LBC2016 / CBC2016 （0.069±0.004）（0.083±0.004）（0.157±0.004）（0.012±0.002） （0.075max.）
LB2012 / CB2012
1.45±0.1
2.25±0.1
4.0±0.1
0.25±0.05 1.45max.
LBC2012 / CBC2012
（0.057±0.004） （0.089±0.004） （0.157±0.004）（0.010±0.002） （0.057max.）
LBR2012
2.3±0.1
4.0±0.1
1.1max.
1.1max.
1.55±0.1
CBL2012
（0.061±0.004） （0.091±0.004） （0.157±0.004） （0.043max.） （0.043max.）
1.8±0.1
4.0±0.1
1.1max.
1.1max.
1.0±0.1
LB1608
（0.039±0.004） （0.071±0.004） （0.157±0.004） （0.043max.） （0.043max.）
1.1±0.1
1.9±0.1
4.0±0.1
0.25±0.05
1.2max.
LBMF1608 /
CBMF1608
（0.043±0.004） （0.075±0.004） （0.157±0.004）（0.010±0.002） （0.047max.）
Unit：mm
（inch）
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli_e-01
12
wound0103_reli-PRP1
■ RELIABILITY DATA
1.Operating temperature Range
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
（Including self-generated heat）
ー40～＋105℃
ー40～＋85℃
2.Storage
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Please refer the term of "7. storage conditions" in precautions.
ー40～＋85℃
3.Rated Current
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
Within the specified tolerance
LBM, LEM Series
【Test Methods and Remarks】
LEM Series
The maximum DC value having inductance decrease within 10％ and temperature increase within 20℃ by the application of DC bias.
4.Inductance
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
LEM Series
Within the specified tolerance
LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series
Measuring equipment：LCR Meter
（HP4285A＋42851A or its equivalent）
Measuring frequency：Specified frequency
Measuring equipment：LCR Mater
（HP4285A or its equivalent）
5.Q
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
LEM Series
Measuring equipment：LCR Meter（HP4285A＋42851A or its equivalent）
Measuring frequency：Specified frequency
LBM Series
Measuring equipment：LCR Mater
（HP4285A or its equivalent）
6.DC Resisitance
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Measuring equipment：DC Ohmmeter
（HIOKI 3227 or its equivalent）
Within the specified tolerance
7.Self-Resonant Frequency
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Measuring equipment：Impedance analyzer
（HP4291A or its equivalent）
8.Temperature Characteristic
LBM2016
LEM2520
CB2012
CBL2012
LB1608
LB2012
LBR2012
CB2016
LB2518
LBR2518
CB2518
LBC3225
CBC2016
LBC2518
LBMF1608 CBMF1608 LBC2016
CBC2518
LB3218
LBC2012
CBC2012
【Test Methods and Remarks】
Change of maximum inductance deviation in step 1-5
LB, CB Series
Step
1
2
LEM2520
Within the specified tolerance
Within the specified tolerance
Inductance change:Within±5％
LB2016
CBC3225
Inductance change:Within±20％
Inductance change:Within±25％
Inductance change:Within±35％
Temperture
（℃）
20
ー40
3
4
20（Reference temperature） ＋85（Maximum operating temperature）
5
20
Step
Temperture
（℃）
1
20
2
ー25
3
4
20（Reference temperature） ＋85（Maximum operating temperature）
5
20
9.Rasistance to Flexure of Substrate
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Warp： 2mm
（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series）
3mm
（LEM2520）
Test substrate: Board according to JIS C0051
No damage.
Pressing jig
LEM2520：1.6mm
LB・LBMF・
CBMF1608
：0.8mm
Others：1.0mm
Board
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli-PRP2
12
wound0103_reli_e-01
■ RELIABILITY DATA
10.Body Strength
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
LB・LBC・LBR・CB・CBC・CBL・LBM・LEM2520
LB1608・LBMF1608・CBMF1608
No damage.
Applied force：10N
Duration：10sec.
Applied force：5N
Duration：10sec.
11.Adhesion of terminal electrode
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF・LEM2520
LB1608・CBMF1608・LBMF1608
No abnormality.
Applied force：10N to X and Y directions
Duration：5 sec.
Test substrate：Printed board
Applied force：5N to X and Y directions
Duration：5 sec.
Test substrate：Printed board
12.Resistance to vibration
LB, LBC, LBR, LBMF Series
Inductance change:Within±10％
CB, CBC, CBL, CBMF Series
LBM, LEM Series
Inductance change:Within±5％
【Test Methods and Remarks】
LEM・LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：According to JIS C5102 clause 8.2.
Vibration type：A
Directions：2 hrs each in X, Y and Z directions. Total：6 hrs
Frequency range：10 to 55 to 10 Hz（1min.）
Amplitude：1.5mm
Mounting method：Soldering onto printed board
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
13.Drop test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
Inductance change:Within±5％
【Test Methods and Remarks】
LEM：
Acceleration：980m/sec2
Duration：6msec
Number of times：6 sides × 3 times
Mounting method：Soldering onto printed board
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
14.Solderability
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
LEM：
No significant abnormality in appearance.
No significant abnormality in appearance.
No significant abnormality in appearance.
At least 90％ of surface of terminal electrode is covered by new
Solder temperature：230±5℃
Duration：5±0.5sec.
Flux：Methanol solution with 25％ of colophony
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： Solder temperature：245±5℃
Duration：5±0.5sec
Flux：Methanol solution with 25％ of colophony
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli_e-01
12
wound0103_reli-PRP3
■ RELIABILITY DATA
15.Resistance to soldering
LB, LBC, LBR, LBMF Series
Inductance change:Within±10％
CB, CBC, CBL, CBMF Series
LEM Series
Inductance change:Within±5％
LEM2520
No significant abnormality in appearance.
【Test Methods and Remarks】
LEM：
Reflow condition 3 times of reflow over at 220±5℃ for 40sec. MAX, With Peak temperature at 240±5℃ for 5 sec.
MAX.（Refer to a Profile of chart below.）
Flow condition
Solder temperature：260±5℃
Duration：10±1sec. Once
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：
3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec.
16.Resisitance to solvent
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Solvent temperature：Room temperature
Type of solvent：Isopropyl alcohol
Cleaning conditions：90s. Immersion and cleaning.
No significant abnormality in appearance
17.Thermal shock
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
Inductance change:Within±10％
Inductance change :Within±10％
Q→ R12～4R7：30 min.
5R6～330：25 min.
390～820：20 min.
101：15 min.
LEM Series
【Test Methods and Remarks】
LEM : Conditions for 1cycle
No significant abnormality in appearance.
Step
1
2
Temperature
（℃）
ー40
＋85
Duration
（min）
30
30
Number of cycle：100 cycle
Recovery：At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF： ー40～＋85℃, maintain times 30min. ,100 cycle
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
18.Damp heat life test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
Inductance change:Within±10％
No significant abnormality in appearance.
Inductance change :Within±10％
Q→ R12～4R7：30 min.
5R6～330：25 min.
390～820：20 min.
101：15 min.
【Test Methods and Remarks】
Temperature：60±2℃
Humidity：90～95％RH
Duration：1000 hrs
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
19.Loading under damp heat life test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
Inductance change:Within±10％
No significant abnormality in appearance.
Inductance change :Within±10％
Q→ R12～4R7：30 min.
5R6～330：25 min.
390～820：20 min.
101：15 min.
【Test Methods and Remarks】
Temperature：60±2℃
Humidity：90～95％RH
Duration：1000 hrs
Applied current：Rated current
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli-PRP4
12
wound0103_reli_e-01
■ RELIABILITY DATA
20.High temperature life test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
Inductance change:Within±10％
No significant abnormality in appearance.
Inductance change :Within±10％
Q→ R12～4R7：30 min.
5R6～330：25 min.
390～820：20 min.
101：15 min.
【Test Methods and Remarks】
Temperature：85±2℃
Duration：1000 hrs
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
21.Loading at high temperature life test
LB, LBC, LBR, LBMF Series
Inductance change:Within±10％
CB, CBC, CBL, CBMF Series
LBM, LEM Series
【Test Methods and Remarks】
Temperature：85±2℃
Duration：1000 hrs
Applied current：Rated current
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
22.Low temperature life test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
LEM Series
Inductance change:Within±10％
No significant abnormality in appearance.
No significant abnormality in appearance.
Inductance change :Within±10％
Q→ R12～4R7：30 min.
5R6～330：25 min.
390～820：20 min.
101：15 min.
【Test Methods and Remarks】
Temperature：－40±2℃
Duration：1000 hrs
Recovery：At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
LEM：Recovery
At least 1 hr of recovery under the standard condition after the test, followed by the measurement within 2 hrs.
23.Standard condition
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM, LEM Series
Standard test conditions
Unless specified, Ambient temperature is 20±15℃ and the Relative humidity is 65±
20％. If there is any doubt about the test results, further measurement shall be had
within the following limits:
Ambient Temperature: 20±2℃
Relative humidity: 65±5％
Inductance value is based on our standard measurement systems.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli_e-01
12
wound0103_reli-PRP5
■ PRECAUTIONS
LEM Type，LB Type，CB Type
1．Circuit Design
◆Operating environment
1．The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
Precautions
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product
failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2．PCB Design
◆Land pattern design
Precautions
1．Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications.
PRECAUTIONS
Technical 【Recommended Land Patterns】
considerSurface Mounting
ations
・Mounting and soldering conditions should be checked beforehand.
・Applicable soldering process to those products is reflow soldering only.
3．Considerations for automatic placement
◆Adjustment of mounting machine
Precautions
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider- 1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
ations
4．Soldering
◆Wave soldering（LEM Type only）
1．For wave soldering,please apply conditions meeting the range of the specifed conditions in our catalog or the relevant specifications.
◆Reflow soldering（LB and CB Types）
1．For reflow soldering with either leaded or lead-free solder,the profile specified in "point for controlling" is recommended.
Precautions ◆Reflow soldering（LEM）
1．For reflow soldering, please apply conditions meeting the range of the specified conditions in our catalog or the relevant specifications.
◆Recommended conditions for using a soldering iron
1．Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron shoud not come in contact
with inductor directly.
◆Wave soldering（LEM Type only）
1．Components can be damaged by excessive heat where soldering conditions exceed the specified range.
◆Reflow soldering（LB and CB Types）
1．Reflow profile
300
Peak Temp: 260＋0/ー5℃
5 sec Max
250
Technical
considerations
200
180℃
230℃ Minn
Pre-heat zone
150 150℃
100
90±30 sec
30±10 sec
50
0
◆Recommended conditions for using a soldering iron
1．Components can be damaged by excessive heat where soldering conditions exceed the specified range.
5．Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
Washing by supersonic waves shall be avoided.
◆Cleaning conditions
If washed by supersonic waves, the products might be broken.
6．Handling
◆Handling
1．There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards（splitting along perforations）
Precautions
1．Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1．There is a case to be damaged by a mechanical shock.
◆Handling
1．Keep the inductors away from all magnets and magnetic objects.
Technical ◆Breakaway PC boards（splitting along perforations）
1．When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board.
consider2．Board separation should not be done manually, but by using the appropriate devices.
ations
◆Mechanical considerations
1．Please do not give the inductors any excessive mechanical shocks.
7．Storage conditions
◆Storage
Precautions
1．Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
◆Storage
1．To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled.
・Recommended conditions
Technical
Ambient temperature：0～40℃ ／ Humidity：Below 70% RH
considerThe ambient temperature must be kept below 30℃ even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For
ations
this reason, LE type inductors should be used within one year from the time of delivery.
LB type：Should be used within 6 months from the time of delivery.
LE type：In case of storage over 6 months, solderability shall be checked before actual usage.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
wound0103_reli-PRP6
12
wound0103_reli_e-01