ON CAT5114VI-10-GT3 32â tap digital potentiometer (pot) Datasheet

CAT5114
32‐tap Digital
Potentiometer (POT)
Description
The CAT5114 is a single digital POT designed as an electronic
replacement for mechanical potentiometers and trim pots. Ideal for
automated adjustments on high volume production lines, they are also
well suited for applications where equipment requiring periodic
adjustment is either difficult to access or located in a hazardous or
remote environment.
The CAT5114 contains a 32-tap series resistor array connected
between two terminals RH and RL. An up/down counter and decoder
that are controlled by three input pins, determines which tap is
connected to the wiper, RW. The wiper setting, stored in nonvolatile
memory, is not lost when the device is powered down and is
automatically reinstated when power is returned. The wiper can be
adjusted to test new system values without affecting the stored setting.
Wiper-control of the CAT5114 is accomplished with three input
control pins, CS, U/D, and INC. The INC input increments the wiper
in the direction which is determined by the logic state of the U/D input.
The CS input is used to select the device and also store the wiper
position prior to power down.
The digital POT can be used as a three-terminal resistive divider or
as a two-terminal variable resistor. Digital POTs bring variability and
programmability to a wide variety of applications including control,
parameter adjustments, and signal processing.
Features








32-position Linear Taper Potentiometer
Non-volatile EEPROM Wiper Storage
Low Standby Current
Single Supply Operation: 2.5 V − 6.0 V
Increment Up/Down Serial Interface
Resistance Values: 10 kW, 50 kW and 100 kW
Available in PDIP, SOIC, TSSOP, MSOP and Space Saving
2  3 mm TDFN Packages
These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
http://onsemi.com
SOIC−8
V SUFFIX
CASE 751BD
MSOP−8
Z SUFFIX
CASE 846AD
PDIP−8
L SUFFIX
CASE 646AA
TSSOP−8
Y SUFFIX
CASE 948AL
TDFN−8
VP2 SUFFIX
CASE 511AK
PIN CONFIGURATIONS
INC
U/D
RH
GND
1
VCC
CS
RL
RWB
PDIP (L), SOIC (V), MSOP (Z)
CS
VCC
INC
U/D
1
RL
RWB
GND
RH
TSSOP (Y)
Applications







INC
U/D
Automated Product Calibration
Remote Control Adjustments
Offset, Gain and Zero Control
Tamper-proof Calibrations
Contrast, Brightness and Volume Controls
Motor Controls and Feedback Systems
Programmable Analog Functions
1
VCC
CS
RL
RWB
RH
GND
TDFN (VP2)
(Top Views)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
 Semiconductor Components Industries, LLC, 2013
June, 2013 − Rev. 23
1
Publication Order Number:
CAT5114/D
CAT5114
DEVICE MARKING INFORMATION
PDIP
RL4B
CAT5114LI
YMXXXX
SOIC
MSOP
RL4B
CAT5114VI
YMXXXX
R = Resistance:
2 = 10 kW
4 = 50 kW
5 = 100 kW
L = Assembly Location
4 = Lead Finish − NiPdAu
B = Product Revision (Fixed as “B”)
CAT5114L = Device Code (PDIP)
CAT5114V = Device Code (SOIC)
I = Temperature Range (Industrial)
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
XXXX = Last Four Digits of Assembly Lot Number
TSSOP
A4RL
4YMXXX
ABMS
YMP
ABMS = CAT5114ZI−10−GT3
ABMT = CAT5114ZI−50−GT3
ABTH = CAT5114ZI−00−GT3
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
P = Product Revision
A4 = Device Code
R = Resistance:
2 = 10 kW
4 = 50 kW
5 = 100 kW
L = Assembly Location
4 = Lead Finish − NiPdAu
Y = Production Year (last digit)
M = Production Month (1−9, O, N, D)
XXX = Last Three Digits of Assembly
XXX = Lot Number
TDFN
EF = CAT5114VP2I10GT3
HF = CAT5114VP2I50GT3
GW = CAT5114VP2I00GT3
L = Assembly Location
XXX = Last Three Digits of Assembly Lot Number
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
EFL
XXX
YM
Functional Diagram
VCC
U/D
INC
CS
5−Bit
Up/Down
Counter
INC
CS
Control
and
Memory
Power On
Recall
GND
RW/VW
RL/VL
VCC
GND
29
5−Bit
Nonvolatile
Memory
28
32−
Position
Decoder
2
Store and
Recall
Control
Circuitry
Transfer
Gates
RW/VW
Resistor
Array
1
0
RL/VL
RW/VW
Figure 1. General
RH/VH
30
RH/VH
U/D
RH/VH
31
Figure 2. Detailed
http://onsemi.com
2
RL/VL
Figure 3. Electronic
Potentiometer
Implementation
CAT5114
than the RH terminal. Voltage applied to the RL terminal
cannot exceed the supply voltage, VCC or go below ground,
GND. RL and RH are electrically interchangeable.
CS: Chip Select
The chip select input is used to activate the control input of
the CAT5114 and is active low. When in a high state, activity
on the INC and U/D inputs will not affect or change the
position of the wiper.
Table 1. PIN DESCRIPTIONS
Name
Function
INC
Increment Control
U/D
Up/Down Control
RH
Potentiometer High Terminal
GND
Ground
RW
Wiper Terminal
RL
Potentiometer Low Terminal
CS
Chip Select
VCC
Supply Voltage
Device Operation
The CAT5114 operates like a digitally controlled
potentiometer with RH and RL equivalent to the high and low
terminals and RW equivalent to the mechanical
potentiometer’s wiper. There are 32 available tap positions
including the resistor end points, RH and RL. There are 31
resistor elements connected in series between the RH and RL
terminals. The wiper terminal is connected to one of the 32
taps and controlled by three inputs, INC, U/D and CS. These
inputs control a seven-bit up/down counter whose output is
decoded to select the wiper position. The selected wiper
position can be stored in nonvolatile memory using the INC
and CS inputs.
With CS set LOW the CAT5114 is selected and will
respond to the U/D and INC inputs. HIGH to LOW
transitions on INC will increment or decrement the wiper
(depending on the state of the U/D input and seven−bit
counter). The wiper, when at either fixed terminal, acts like
its mechanical equivalent and does not move beyond the last
position. The value of the counter is stored in nonvolatile
memory whenever CS transitions HIGH while the INC input
is also HIGH. When the CAT5114 is powered-down, the last
stored wiper counter position is maintained in the
nonvolatile memory. When power is restored, the contents
of the memory are recalled and the counter is set to the value
stored.
With INC set low, the CAT5114 may be de-selected and
powered down without storing the current wiper position in
nonvolatile memory. This allows the system to always
power up to a preset value stored in nonvolatile memory.
Pin Function
INC: Increment Control Input
The INC input moves the wiper in the up or down direction
determined by the condition of the U/D input.
U/D: Up/Down Control Input
The U/D input controls the direction of the wiper movement.
When in a high state and CS is low, any high-to-low
transition on INC will cause the wiper to move one
increment toward the RH terminal. When in a low state and
CS is low, any high-to-low transition on INC will cause the
wiper to move one increment towards the RL terminal.
RH: High End Potentiometer Terminal
RH is the high end terminal of the potentiometer. It is not
required that this terminal be connected to a potential greater
than the RL terminal. Voltage applied to the RH terminal
cannot exceed the supply voltage, VCC or go below ground,
GND.
RW: Wiper Potentiometer Terminal
RW is the wiper terminal of the potentiometer. Its position on
the resistor array is controlled by the control inputs, INC,
U/D and CS. Voltage applied to the RW terminal cannot
exceed the supply voltage, VCC or go below ground, GND.
RL: Low End Potentiometer Terminal
RL is the low end terminal of the potentiometer. It is not
required that this terminal be connected to a potential less
http://onsemi.com
3
CAT5114
Table 2. OPERATION MODES
INC
CS
U/D
Operation
High to Low
Low
High
Wiper toward H
High to Low
Low
Low
Wiper toward L
High
Low to High
X
Store Wiper Position
Low
Low to High
X
No Store, Return to Standby
X
High
X
Standby
RH
CH
RWI
RW
CW
CL
RL
Figure 4. Potentiometer Equivalent Circuit
Table 3. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Supply Voltage
VCC to GND
−0.5 to +7
Inputs
CS to GND
−0.5 to VCC +0.5
Units
V
V
INC to GND
−0.5 to VCC +0.5
V
U/D to GND
−0.5 to VCC +0.5
V
H to GND
−0.5 to VCC +0.5
V
L to GND
−0.5 to VCC +0.5
V
W to GND
−0.5 to VCC +0.5
V
Operating Ambient Temperature
Industrial (‘I’ suffix)
C
−40 to +85
Junction Temperature
+150
C
Storage Temperature
−65 to 150
C
+300
C
Lead Soldering (10 s max)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. RELIABILITY CHARACTERISTICS
Symbol
Parameter
VZAP (Note 1)
ESD Susceptibility
MIL−STD−883, Test Method 3015
2000
V
Latch-up
JEDEC Standard 17
100
mA
Data Retention
MIL−STD−883, Test Method 1008
100
Years
Endurance
MIL−STD−883, Test Method 1003
1,000,000
Stores
ILTH (Notes 1, 2)
TDR
NEND
Test Method
Min
Typ
1. This parameter is tested initially and after a design or process change that affects the parameter.
2. Latch-up protection is provided for stresses up to 100 mA on address and data pins from −1 V to VCC + 1 V.
http://onsemi.com
4
Max
Units
CAT5114
Table 5. DC ELECTRICAL CHARACTERISTICS (VCC = +2.5 V to +6 V unless otherwise specified)
Parameter
Min
Typ
Max
Units
2.5
–
6.0
V
VCC = 6 V, f = 1 MHz, IW = 0
–
–
100
mA
VCC = 6 V, f = 250 kHz, IW = 0
–
–
50
mA
Programming, VCC = 6 V
–
–
1000
mA
VCC = 3 V
–
–
500
mA
Supply Current (Standby)
CS = VCC − 0.3 V
U/D, INC = VCC − 0.3 V or GND
–
−
1
mA
IIH
Input Leakage Current
VIN = VCC
–
–
10
mA
IIL
Input Leakage Current
VIN = 0 V
–
–
−10
mA
VIH2
CMOS High Level Input Voltage
2.5 V  VCC  6 V
VCC x 0.7
–
VCC + 0.3
V
VIL2
CMOS Low Level Input Voltage
−0.3
–
VCC x 0.2
V
Symbol
Conditions
POWER SUPPLY
VCC
Operating Voltage Range
ICC1
Supply Current (Increment)
ICC2
Supply Current (Write)
ISB1 (Note 4)
LOGIC INPUTS
POTENTIOMETER CHARACTERISTICS
RPOT
Potentiometer Resistance
−10 Device
10
−50 Device
50
−00 Device
100
Pot. Resistance Tolerance
VRH
Voltage on RH pin
0
VRL
Voltage on RL pin
0
Resolution
20
%
VCC
V
VCC
3.2
V
%
INL
Integral Linearity Error
IW  2 mA
0.5
1
LSB
DNL
Differential Linearity Error
IW  2 mA
0.25
0.5
LSB
RWI
Wiper Resistance
VCC = 5 V, IW = 1 mA
70
200
W
VCC = 2.5 V, IW = 1 mA
150
400
W
IW
Wiper Current
TCRPOT
TC of Pot Resistance
TCRATIO
Ratiometric TC
VN
CH/CL/CW
fc
3.
4.
5.
6.
kW
Noise
−4.4
100 kHz / 1 kHz
Passive Attenuator, 10 kW
5
ppm/C
8/24
nV/Hz
8/8/25
pF
1.7
MHz
This parameter is tested initially and after a design or process change that affects the parameter.
Latch−up protection is provided for stresses up to 100 mA on address and data pins from −1 V to VCC + 1 V.
IW = source or sink.
These parameters are periodically sampled and are not 100% tested.
http://onsemi.com
mA
ppm/C
20
Potentiometer Capacitances
Frequency Response
4.4
300
CAT5114
Table 6. AC TEST CONDITIONS
VCC Range
2.5 V  VCC  6 V
Input Pulse Levels
0.2 x VCC to 0.7 x VCC
Input Rise and Fall Times
10 ns
Input Reference Levels
0.5 x VCC
Table 7. AC OPERATING CHARACTERISTICS (VCC = +2.5 V to +6.0 V, VH = VCC, VL = 0 V, unless otherwise specified)
Parameter
Symbol
Min
Typ (Note 7)
Max
Units
100
−
−
ns
tCI
CS to INC Setup
tDI
U/D to INC Setup
50
−
−
ns
tID
U/D to INC Hold
100
−
−
ns
tIL
INC LOW Period
250
−
−
ns
tIH
INC HIGH Period
250
−
−
ns
tIC
INC Inactive to CS Inactive
1
−
−
ms
tCPH
CS Deselect Time (NO STORE)
100
−
−
ns
tCPH
CS Deselect Time (STORE)
10
−
−
ms
INC to VOUT Change
−
1
5
ms
INC Cycle Time
1
−
−
ms
INC Input Rise and Fall Time
−
−
500
ms
Power-up to Wiper Stable
–
–
1
ms
Store Cycle
–
5
10
ms
tIW
tCYC
tR, tF (Note 8)
tPU (Note 8)
tWR
7. Typical values are for TA = 25C and nominal supply voltage.
8. This parameter is periodically sampled and not 100% tested.
9. MI in the A.C. Timing diagram refers to the minimum incremental change in the W output due to a change in the wiper position.
CS
tCI
tIL
tCYC
tIC
tIH
(store)
tCPH
90%
INC
90%
10%
tDI
tID
tF
U/D
tR
MI(3)
tIW
RW
Figure 5. A.C. Timing
http://onsemi.com
6
CAT5114
APPLICATIONS INFORMATION
(a) resistive divider
(b) variable resistance
(c) two−port
Figure 6. Potentiometer Configuration
Applications
R1
4
CAT5113/5114
V2 (+)
6
5
R3
1
R4
–
+5 V
8
Digital
POT
2
1
7
A1
–
+5 V
4A
9 –
3
10
8
+
11
R2
R2
A2
7
+
R4
R3
2
1
7
+5 V
8
Digital
POT
2
1
7
+5 V
8
4
1.23 V
FB
GND
R1
11 kW
8
5 (1−p)R
POT
3
555
5
2
0.01 mF
0.003 mF
1
0.01 mF
Figure 8. Programmable Sq. Wave Oscillator (555)
2
1
7
+5 V
8
330 W
pR (1−p)R
6
2
IS
CAT5113/5114
4
0.1 mF 6.8 mF
R3
10 kW
6
4
R2
C
3
5
7
6
R2
820 W
1 mF
pRPOT
+2.5 V
VO (REG)
2952
CAT5113/5114
3
A1 = A2 = A3 = 1/4 LM6064
R2 = R3 = R4 = 5 kW
RPOT = 10 kW
VOUT
SD
6
RB
CAT5114
100 kW
SHUTDOWN
RA
4
VO
Figure 7. Programmable Instrumentation
Amplifier
VIN (UNREG)
+5 V
R1
Digital
POT
2
+
Digital
POT
3
V1 (−)
3
+5 V
7
–
+
4
5
A1
6
1 MW
330 W
3
10 k
2
3
+5 V
7
–
+
LT1097
Figure 9. Programmable Voltage Regulator
4
A2
VO
6
+2.5 V
Figure 10. Programmable I to V Convertor
http://onsemi.com
7
CAT5114
C1
0.001 mF
1 mF
VS
50 kW
0.001 mF
R2
10 kW
Digital
POT
2
1
7
+5 V
8
C2
R1
4
R3
100 kW
+5 V
2
7
–
3
+
4
VO
6
A1
+2.5 V
CAT5113/5114
Figure 11. Programmable Bandpass Filter
+5 V
IC1
393
–
IC2
74HC132
1
OSC
CLO
CHI 7
Digital
POT
+
4
–
0.1 mF
IC3
CAT5114
+5 V
8
2
10 kW
1
7
+
10 kW
2
3
6
R1
VLL
R2
R3
5
VUL
+5 V
+5 V
6
3
5
–
+
VS
+2.5 V
AI
IC4
2.5  VO  5 V
0  VS  2.5 V
Figure 12. Automatic Gain Control
http://onsemi.com
8
VO
CAT5114
Table 8. ORDERING INFORMATION
Orderable Part Numbers
Resistance Values (kW)
CAT5114LI−10−G
10
CAT5114LI−50−G
50
CAT5114LI−00−G
100
CAT5114VI−10−GT3
10
CAT5114VI−50−GT3
50
CAT5114VI−00−GT3
100
CAT5114VP2I10GT3 (Notes 10, 11)
10
CAT5114VP2I50GT3 (Notes 10, 11)
50
CAT5114VP2I00GT3 (Notes 10, 11)
100
CAT5114YI−10−GT3
10
CAT5114YI−50−GT3
50
CAT5114YI−00−GT3
100
CAT5114ZI−10−GT3
10
CAT5114ZI−50−GT3
50
CAT5114ZI−00−GT3
100
Package−Pin
Lead Finish
Shipping†
PDIP−8
NiPdAu
50 Units / Rail
SOIC−8
NiPdAu
100 Units / Rail
TDFN−8
2 x 3 mm
NiPdAu
3000 / Tape & Reel
TSSOP−8
NiPdAu
3000 / Tape & Reel
MSOP−8
NiPdAu
96 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
10. Contact factory for package availability.
11. Part number is not exactly the same as the “Example of Ordering Information” shown above. For the indicated part numbers there are NO
hyphens in the orderable part numbers.
12. All packages are RoHS-compliant (Pb-Free, Halogen-Free).
13. The standard lead finish is NiPdAu.
14. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office.
http://onsemi.com
9
CAT5114
PACKAGE DIMENSIONS
PDIP−8, 300 mils
CASE 646AA
ISSUE A
SYMBOL
MIN
NOM
A
E1
5.33
A1
0.38
A2
2.92
3.30
4.95
b
0.36
0.46
0.56
b2
1.14
1.52
1.78
c
0.20
0.25
0.36
D
9.02
9.27
10.16
E
7.62
7.87
8.25
E1
6.10
6.35
7.11
e
PIN # 1
IDENTIFICATION
MAX
2.54 BSC
eB
7.87
L
2.92
10.92
3.30
3.80
D
TOP VIEW
E
A2
A
A1
c
b2
L
e
eB
b
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MS-001.
http://onsemi.com
10
CAT5114
PACKAGE DIMENSIONS
SOIC 8, 150 mils
CASE 751BD
ISSUE O
E1
E
SYMBOL
MIN
A
1.35
1.75
A1
0.10
0.25
b
0.33
0.51
c
0.19
0.25
D
4.80
5.00
E
5.80
6.20
E1
3.80
MAX
4.00
1.27 BSC
e
PIN # 1
IDENTIFICATION
NOM
h
0.25
0.50
L
0.40
1.27
θ
0º
8º
TOP VIEW
D
h
A1
θ
A
c
e
b
L
END VIEW
SIDE VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-012.
http://onsemi.com
11
CAT5114
PACKAGE DIMENSIONS
MSOP 8, 3x3
CASE 846AD
ISSUE O
SYMBOL
MIN
NOM
MAX
1.10
A
E
A1
0.05
0.10
0.15
A2
0.75
0.85
0.95
b
0.22
0.38
c
0.13
0.23
D
2.90
3.00
3.10
E
4.80
4.90
5.00
E1
2.90
3.00
3.10
E1
0.65 BSC
e
L
0.60
0.40
0.80
L1
0.95 REF
L2
0.25 BSC
θ
0º
6º
TOP VIEW
D
A
A2
A1
DETAIL A
e
b
c
SIDE VIEW
END VIEW
q
L2
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-187.
L
L1
DETAIL A
http://onsemi.com
12
CAT5114
PACKAGE DIMENSIONS
TSSOP8, 4.4x3
CASE 948AL
ISSUE O
b
SYMBOL
MIN
NOM
1.20
A
E1
E
MAX
A1
0.05
A2
0.80
b
0.19
0.15
0.90
1.05
0.30
c
0.09
D
2.90
3.00
3.10
E
6.30
6.40
6.50
E1
4.30
4.40
4.50
0.20
0.65 BSC
e
L
1.00 REF
L1
0.50
θ
0º
0.60
0.75
8º
e
TOP VIEW
D
A2
c
q1
A
A1
L1
SIDE VIEW
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
http://onsemi.com
13
CAT5114
PACKAGE DIMENSIONS
TDFN8, 2x3
CASE 511AK
ISSUE A
D
A
e
b
E2
E
PIN#1
IDENTIFICATION
A1
PIN#1 INDEX AREA
D2
TOP VIEW
SIDE VIEW
SYMBOL
MIN
NOM
MAX
A
0.70
0.75
0.80
A1
0.00
0.02
0.05
A2
0.45
0.55
0.65
A3
A2
A3
0.20
0.25
0.30
D
1.90
2.00
2.10
D2
1.30
1.40
1.50
E
2.90
3.00
3.10
E2
1.20
1.30
1.40
L
BOTTOM VIEW
0.20 REF
b
e
FRONT VIEW
0.50 TYP
0.20
0.30
L
0.40
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MO-229.
http://onsemi.com
14
CAT5114
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT5114/D
Similar pages