Coilcraft LPO4812-332ML Smt power inductor Datasheet

Document 276-1
SMT Power Inductors–LPO4812 Series
• Very low profile - only 1.2 mm high!
• Handles up to 1.3 Amps saturating current
Designer’s Kit C357 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 53 – 61 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 8 mm pocket spacing, 1.3 mm pocket depth
Recommended pick and place nozzle OD: 4.6 mm; ID: ≤ 2.3 mm
PCB washing Only pure water or alcohol recommended
Part number1
LPO4812-102ML_
LPO4812-152ML_
LPO4812-222ML_
LPO4812-332ML_
LPO4812-472ML_
LPO4812-682ML_
LPO4812-822ML_
LPO4812-103KL_
LPO4812-153KL_
LPO4812-223KL_
LPO4812-333KL_
LPO4812-473KL_
LPO4812-683KL_
LPO4812-104KL_
LPO4812-154KL_
LPO4812-224KL_
DCR
SRF
L2
max
typ Isat3
(µH)
(Ohms) (MHz) (A)
1.0 ±20% 0.055
270 1.30
1.5 ±20% 0.080
220 1.00
2.2 ±20% 0.090
170 0.80
3.3 ±20% 0.120
140 0.70
4.7 ±20% 0.155
110 0.60
6.8 ±20% 0.225
90 0.45
8.2 ±20% 0.270
70 0.45
0.300
60 0.40
10.±10%
15.±10%
0.460
50 0.32
22.±10%
0.640
40 0.28
33.±10%
0.850
30 0.22
47.±10%
1.30
28 0.20
1.80
22 0.16
68.±10%
100.±10%
2.60
18 0.13
150.±10%
4.20
14 0.10
220.±10%
5.50
11 0.09
Irms4
(A)
0.85
0.85
0.85
0.80
0.80
0.78
0.77
0.76
0.72
0.59
0.54
0.50
0.39
0.32
0.26
0.24
1. When ordering, please specify termination and packaging codes:
LPO4812-473MLC
Termination: L = RoHS compliant silver-palladium-platinum-glass frit
Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B= Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter C instead.
D= 13″ machine-ready reel. EIA-481 embossed plastic
tape (3500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms 0 Adc.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 276-1
Revised 10/14/08
Document 276-2
SMT Power Inductors - LPO4812 Series
Typical L vs Frequency
Typical L vs Current
Irms Derating
0.047
max
1,2
120
0.181
max
4,6
110
0.031 ±0.005
0,787 ±0,127
Dash number
90
0.190
max
4,83
80
70
60
Internal code
0.107
typ
2,72
50
XXX
X
40
25°C
Percent of rated Irms
100
30
20
0.035
0,89
10
0
-40
-20
0
20
40
60
80
100
Recommended
Land Pattern
0.158
4,01
120 140
Ambient temperature (°C)
0.181
4,6
Dimensions are in
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
© Coilcraft, Inc. 2009
Document 276-2
Revised 10/14/08
Similar pages