Features ■ ■ ■ ■ No backlash - mounted directly to potentiometer shaft For use with precision potentiometers or other rotating devices up to 30 turns Compact size - requires only 25.4 mm diameter panel space Available with or without brake Model H-490 is currently available, although not recommended for new designs. Models H-23 and H-506 are preferred. H-490 Turns-Counting Dial Mechanical and Physical Characteristics Number of Turns ..................................................................................................................................................................................0 to 30 Dial Divisions ...............................................................................................................................................................................100 per turn Readability - Over 10 Turns ......................................................................................................................................................1 part in 1000 Torque With Brake Engaged .............................................................................................................................350 g-cm (5 oz-in.) minimum Markings .............................................................................................................................................................White on black background Locking Brake.................................................................................................................................................................Refer to chart below Weight ..........................................................................................................................................................Approximately 7 grams (1/4 oz.) Set Screws .............................................................................................................................................UNC-3A 4-40, 2 screws 120 º apart Set Screw Tightening Torque ......................................................................................................................22.59 N-cm (2 lbs.-in.) minimum Hex Key Size ................................................................................................................................................................................0.05 in. hex Shaft and Bushing Requirements Shaft Diameter Requirements ........................................................................................................................................Refer to chart below Shaft Extension Beyond Panel .........................................................................................................................15.75 mm (0.62 in.) minimum 21.21 mm (0.83 in.) maximum Bushing Extension Beyond Panel .....................................................................................................................9.02 mm (0.35 in.) maximum H-490 MOUNTING INSTRUCTIONS 1. Discard standard mounting nut and lockwasher supplied with the potentiometer; they will not be used. 2. Insert potentiometer in panel. 3. Using parts supplied with dial, position anti-rotation washer against panel. Tangs of washer should stick out from panel. 4. Install mounting nut supplied with dial. Be sure: a. Shoulder on nut engages hold of anti rotation washer. b. Tangs of anti-rotation washer are aligned vertically. This positions the turns-counting window properly. 5. Turn potentiometer shaft counterclockwise to minimum resistance or voltage ratio. This is not necessarily at the end of travel. 6. Loosen set screw in knob of dial assembly. Set dial to “0.00” reading. Slip dial assembly over end of potentiometer shaft. 7. Holding outer ring of dial assembly, engage locating tangs on anti-rotation washer in notches on dial assembly. 8. While holding outer ring, position unit lightly against panel. Uniformly tighten knob set screws to potentiometer shaft with furnished hex wrench. Dimensional Drawings 30 ° ± 5 ° 45 ° ± 10 ° BRAKE 2 0 1 18.29 RAD. MAX. (.720) 9 7 3 2 8 12.7 (.500) 6 5 4 25.4 DIA. (1.0) DIMENSIONS: 10.36 (.407) DIA. 11.18 (.440) 23.11 ± .76 (.909 ± .029) MM (INCHES) How to Order Part Number Accepts Shaft Diameter Fits Bushing Size Brake Body Finish H-493-2 H-494-2 H-491-3 H-492-3 H-493-3 H-494-3 H-492-2 3.18 mm (.125 in.) 3.18 mm (.125 in.) 6.35 mm (.250 in.) 6.35 mm (.250 in.) 6.35 mm (.250 in.) 6.35 mm (.250 in.) 3.18 mm (.125 in.) 6.35 mm-32UNEF-2A 6.35 mm-32UNEF-2A 9.53 mm-32UNEF-2A 9.53 mm-32UNEF-2A 9.53 mm-32UNEF-2A 9.53 mm-32UNEF-2A 6.35 mm-32UNEF-2A No Yes No Yes No Yes Yes Black Black Satin Chrome Satin Chrome Black Black Satin Chrome REV. 02/06 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications.