Small and High Accuracy Temperature Sensor IC Series Detect TemperatureChangeable Thermostat Output Temperature Sensor IC BDE□□□0G Series No.09047EAT03 ●Description Low quiescent current (16µA), high accuracy thermostat (temperature switch) ICs. Built in temperature sensor, reference voltage regulator, D/A converter, and comparator. Detecting temperature by itself, OS terminal state is changed at logically. Open Drain Output ( Active L ) is available in BDE□□□0G series. ●Features 1) Detection Temperature Range -25～+125℃ by 15 products. 2) ±5℃ Step Selectable Detection Temperature with CTRL. 3) Hysteresis Temperature ( typically 10℃ ) 4) High Accuracy Analog Output ( typically ±3.5℃@Ta=30℃ ) 5) Analog Output Temperature Sensitivity ( typically -10.8mV/℃ ) 6) Low Supply Current ( typically 16µA ) 7) Small Package ( typically 2.90mm×2.80mm×1.25mm ) 8) ESD Rating 8kV ( HBM ) 9) Excellent Ripple Rejection Characteristic ●Applications Thermal Protection for Electrical Equipment (NoteBook PC, Cell phone, FPD-TV, etc.) FAN Control for Thermal Management ●Products Line up BDE 0 □□□ Detection Temperature (Center Temperature) 120:120℃ 040: 40℃ 110:110℃ 030: 30℃ 100:100℃ 020: 20℃ 090: 90℃ 010: 10℃ 080: 80℃ 000: 0℃ 070: 70℃ 910:-10℃ 060: 60℃ 920:-20℃ 050: 50℃ G Output Format (OpenDrain, Active Low) Temperature / Output Format Table CTRL status description ( L : Low, O : Open, H O 115 105 95 85 75 65 55 45 120 110 100 90 80 70 60 50 125 115 105 95 85 75 65 55 Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Active L Active L Active L Active L Active L Active L Active L Active L eA eB eC eD eE eF eG eH 1/8 Product Name BDE0400G BDE0300G BDE0200G BDE0100G BDE0000G BDE9100G BDE9200G H : High ) Detection Temperature (℃) CTRL L H O 35 25 15 5 -5 -15 -25 40 30 20 10 0 -10 -20 45 35 25 15 5 -5 -15 OS Output Format Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Open Drain Active L Active L Active L Active L Active L Active L Active L Marking BDE1200G BDE1100G BDE1000G BDE0900G BDE0800G BDE0700G BDE0600G BDE0500G L OS Output Format Marking Product Name Detection Temperature (℃) CTRL Package (SSOP5) eJ eK eL eM eN eP eQ 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Absolute Maximum Ratings ( Ta = 25℃ ) Parameters Power Supply Voltage Input Voltage ( CTRL ) Input Current ( CTRL ) OS terminal Voltage OS terminal Current Power dissipation Storage Temperature Range Symbol Limit Unit VDD VIN IIN VOS IOS Pd Tstg -0.3 to 7.0*1 -0.3 to VDD+0.3 -1.0, +0.1 -0.3 to 7.0 5.0 540※2 -55 to 150 V V mA V mA mW ℃ *1. Not to exceed Pd *2. Reduced by 5.40mW for each increase in Ta of 1℃ over 25℃( mounted on 70mm×70mm×1.6mm Glass-epoxy PCB ) ●Recommended Operating Condition Parameters Power Supply Voltage Operating Temperature Range Symbol Min. Typ. Max. Unit VDD Topr 2.9 -30 3.0 - 5.5 130 V ℃ Min. Limit Typ. Max. Tacc - 0 Thys 7.5 10.0 ±4.0 ±5.0 12.5 TTemp - - ±3.5 ●Temperature Accuracy ( Unless otherwise specified, VDD = 3.0V ) Parameters Symbol Unit Conditions Thermostat ( Temperature Switch ) Detection TemperatureAccuracy Detection Temperature Hysteresis Analog Output VTemp Temperature Accuracy ●Electrical Characteristics ( Unless otherwise specified, VDD = 3.0V, Ta = 25℃ ) LIMIT PARAMETER SYMBOL MIN. TYP. MAX. Supply Current IDD 16.0 20.0 Analog Output VTemp Output Voltage VTemp 1.716 1.753 1.790 VTemp Temperature Sensitivity VSE -10.28 -10.68 -11.08 VTemp Load Regulation OS Output Open Drain OS Leakage Current OS Output Voltage CTRL Input L Voltage Input H Voltage ℃ Ta = -20℃～115℃ Ta = ～125℃ ℃ ℃ UNIT µA V mV/℃ ⊿VTempRL - - 1 mV IL VOL - - 1.0 0.4 µA V VIL VIH GND 2.4 - 0.6 VDD V V Ta = 30℃ CONDITIONS CTRL = 3.0V Ta = 30℃ Ta = -30 to 100℃ difference of IOUT : 0µA / 2µA OS : 5.0V IinOS = 1.2mA *Radiation hardiness is not designed. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 2/8 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Package Outline Product Type Lot No. SSOP5 (Unit：mm ) ●Pin Description Pin No. Pin Name Function 1 CTRL Detection temperature setting 2 GND GROUND 3 Vtemp 4 VDD 5 OS Comment Refer to 2/7 page for the emperature set. ( Temperature / Output Format Table ) - Output voltage in inverse proportion to the temperature( TYP. -10.68mV/℃) POWER SUPPLY Open Drain type Use the pull-up resistor over 10kΩ. Digital thermostat output www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Set the OPEN state or Connect high impedance input node. 3/8 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Equivalence Circuit CTRL OS VDD OS CTRL GND GND Please connect the pull-up resistor over 10kΩ. VTemp VDD VTemp GND Please don’t connect the pull-down resistor ●Block Diagram CTRL 1 GND 2 VTemp 3 www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. OUT Vref 5 OS + - TEMP SENSOR Iref 4/8 4 VDD 2009.06 - Rev.A Technical Note BDE□□□0G Series Analog Output Voltage ( VTemp ) [V] ●Functional Diagram ( ex. Detection Temperature 110℃ ) 3.0 2.5 Temperature Sensitivity ( -10.68mV/℃ Typical ) 2.0 VTemp@30℃ ( 1.753V Typical ) 1.5 1.0 0.5 -50 -30 -10 10 30 50 70 90 110 130 110 130 OS Output Voltage ( VOS ) [V] Temperature [℃] Temperature Hysteresis ( 10℃ Typical ) Vos 0 -50 -30 -10 10 30 50 70 90 Temperature [℃] www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 5/8 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Reference Data 25 3.0 VDD=3V 20 2.0 IDD [uA] VTemp [V] 2.5 1.5 1.0 15 10 5 0.5 Ta=25℃ 0.0 -80 -40 0 0 40 80 120 160 0 1 2 Temperature [℃] 4 5 6 7 8 VDD [V] Fig2. Supply Current vs. Supply Voltage Fig1. VTemp Voltage vs. Temperature (Temperature Sensitivity) 25 3.0 Ta=25℃ 0 2.5 -25 2.0 -50 ΔVTemp [mV] VTemp [V] 3 1.5 1.0 0.5 -75 -100 -125 -150 -175 0.0 0 1 2 3 4 5 6 7 VDD=3V, Ta=25℃ -200 8 0 1 2 3 4 5 ITemp [uA] VDD [V] Fig3. VTemp Voltage vs. Supply Voltage Fig4. VTemp Voltage vs. Output Current 3.0 VDD=3V, Ta=25℃ 2.5 VOS[V] 2.0 1.5 1.0 0.5 0.0 0 5 10 15 20 25 IOS [mA] Fig5. OS Output Voltage vs. Load Current www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 6/8 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Notes for use 1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. 2) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. 3) Pin short and mistake fitting When mounting the IC on the PCB, pay attention to the orientation of the IC. If there is a placement mistake, the IC may be burned up. 4) Operation in strong electric field Be noted that using ICs in the strong electric field can malfunction them. 5) Mutual impedance Use short and wide wiring tracks for the power supply and ground to keep the mutual impedance as small as possible. Use a capacitor to keep ripple to a minimum. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 7/8 2009.06 - Rev.A Technical Note BDE□□□0G Series ●Ordering part number B D E 0 Part No. 0 Part No. 0000 0100 0300 0400 0600 0700 0900 1000 1200 9100 0 0 G - Package G: SSOP5 0200 0500 0800 1100 9200 T R Packaging and forming specification TR: Embossed tape and reel (SSOP5) SSOP5 5 4 1 2 0.2Min. +0.2 1.6 −0.1 2.8±0.2 <Tape and Reel information> +6° 4° −4° 2.9±0.2 3 Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand 1pin +0.05 0.13 −0.03 0.05±0.05 1.1±0.05 1.25Max. ) +0.05 0.42 −0.04 0.95 0.1 Direction of feed Reel (Unit : mm) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 8/8 ∗ Order quantity needs to be multiple of the minimum quantity. 2009.06 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A