ATMEL AT25080AN-10SI-1.8 Spi serial eeprom Datasheet

Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
– Data Sheet Describes Mode 0 Operation
• Medium-voltage and Standard-voltage Operation
•
•
•
•
•
•
•
•
– 2.7 (VCC = 2.7V to 5.5V)
Extended Temperature Range –40°C to 125°C
5.0 MHz Clock Rate
32-byte Page Mode
Block Write Protection
– Protect 1/4, 1/2, or Entire Array
Write Protect (WP) Pin and Write Disable Instructions for Both Hardware and Software
Data Protection
Self-timed Write Cycle (2 ms [5V] typical)
High Reliability
– Endurance: One Million Write Cycles
– Data Retention: 100 Years
8-lead PDIP, 8-lead JEDEC SOIC Packages and 8-lead TSSOP Packages
Description
The AT25080A/160A/320A/640A provides 8192/16384/32768/65536 bits of serial
electrically-erasable programmable read-only memory (EEPROM) organized as
1024/2048/4096/8192 words of 8 bits each. The device is optimized for use in many
automotive applications where low-power and low-voltage operation are essential.
The AT25080A/160A/320A/640A is available in space-saving 8-lead PDIP, 8-lead
JEDEC SOIC and 8-lead TSSOP packages.
The AT25080A/160A/320A/640A is enabled through the Chip Select pin (CS) and
accessed via a three-wire interface consisting of Serial Data Input (SI), Serial Data
Output (SO), and Serial Clock (SCK). All programming cycles are completely selftimed, and no separate erase cycle is required before write.
Block write protection is enabled by programming the status register with one of four
blocks of write protection. Separate program enable and program disable instructions
are provided for additional data protection. Hardware data protection is provided via
the WP pin to protect against inadvertent write attempts to the status register. The
HOLD pin may be used to suspend any serial communication without resetting the
serial sequence.
Function
CS
Chip Select
SCK
Serial Data Clock
SI
Serial Data Input
SO
Serial Data Output
GND
Ground
VCC
Power Supply
WP
Write Protect
HOLD
Suspends Serial Input
NC
No Connect
DC
Don’t Connect
AT25080A
AT25160A
AT25320A
AT25640A
8-lead PDIP
Table 1. Pin Configurations
Pin Name
SPI Serial
Extended
Temperature
EEPROMs
8K (1024 x 8)
16K (2048 x 8)
32K (4096 x 8)
64K (8192 x 8)
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
8-lead SOIC
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
8-lead TSSOP
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
5082B–SEEPR–1/05
1
Absolute Maximum Ratings*
Operating Temperature......................................−40°C to +125°C
Storage Temperature .........................................−65°C to +150°C
Voltage on Any Pin
with Respect to Ground ........................................ −1.0V to +7.0V
Maximum Operating Voltage .......................................... 6.25V
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
DC Output Current........................................................ 5.0 mA
Figure 1. Block Diagram
2
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
Table 2. Pin Capacitance(1)
Applicable over recommended operating range from TAE = 25°C, f = 1.0 MHz, VCC = +5.0V (unless otherwise noted)
Symbol
Test Conditions
Max
Units
Conditions
COUT
Output Capacitance (SO)
8
pF
VOUT = 0V
CIN
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
VIN = 0V
Note:
1. This parameter is characterized and is not 100% tested.
Table 3. DC Characteristics
Applicable over recommended operating range from: TAE = −40°C to +125°C, VCC = +2.7V to +5.5V
Symbol
Parameter
VCC1
Supply Voltage
ICC1
Supply Current
ICC2
Max
Units
5.5
V
VCC = 5.0V at 5 MHz, SO = Open, Read
6.0
mA
Supply Current
VCC = 5.0V at 1 MHz
3.0
mA
ICC3
Supply Current
VCC = 5.0V at 5 MHz, SO = Open,
Read, Write
7.0
mA
ISB1
Standby Current
VCC = 2.7V, CS = VCC
0.2
10.0(1)
µA
ISB2
Standby Current
VCC = 5.0V, CS = VCC
2.0
13.0(1)
µA
IIL
Input Leakage
VIN = 0V to VCC
−3.0
Output Leakage
VIN = 0V to VCC
−3.0
3.0
µA
Input Low-voltage
−0.6
VCC x 0.3
V
VIH(2)
Input High-voltage
VCC x 0.7
VCC + 0.5
V
VOL1
Output Low-voltage
0.4
V
VOH1
Output High-voltage
IOL
VIL
(2)
Note:
Test Condition
Min
Typ
2.7
2.7V ≤ VCC ≤ 5.5V
IOL = 3.0 mA
IOH = −1.6 mA
VCC − 0.8
µA
V
1. Worst case measured at 125°C
2. VIL min and VIH max are reference only and are not tested.
3
5082B–SEEPR–1/05
Table 4. AC Characteristics
Applicable over recommended operating range from TAE = −40°C to +125°C, VCC = As Specified,
CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol
Parameter
Voltage
Min
Max
Units
fSCK
SCK Clock Frequency
2.7–5.5
0
5.0
MHz
tRI
Input Rise Time
2.7–5.5
2
µs
tFI
Input Fall Time
2.7–5.5
2
µs
tWH
SCK High Time
2.7–5.5
40
ns
tWL
SCK Low Time
2.7–5.5
40
ns
tCS
CS High Time
2.7–5.5
80
ns
tCSS
CS Setup Time
2.7–5.5
80
ns
tCSH
CS Hold Time
2.7–5.5
80
ns
tSU
Data In Setup Time
2.7–5.5
5
ns
tH
Data In Hold Time
2.7–5.5
20
ns
tHD
Hold Setup Time
2.7–5.5
40
ns
tCD
Hold Hold Time
2.7–5.5
40
ns
tV
Output Valid
2.7–5.5
0
tHO
Output Hold Time
2.7–5.5
0
tLZ
Hold to Output Low Z
2.7–5.5
0
tHZ
Hold to Output High Z
tDIS
tWC
Endurance(1)
Note:
4
40
ns
ns
40
ns
2.7–5.5
80
ns
Output Disable Time
2.7–5.5
80
ns
Write Cycle Time
2.7–5.5
5
ms
5.0V, 25°C, Page Mode
1M
Write Cycles
1. This parameter is characterized and is not 100% tested.
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
Serial Interface
Description
MASTER: The device that generates the serial clock.
S L AV E : B e c a u s e t h e s e r i a l c l o c k p i n ( S C K ) i s a l w a y s a n i n p u t , t h e
AT25080A/160A/320A/640A always operates as a slave.
TRANSMITTER/RECEIVER: The AT25080A/160A/320A/640A has separate pins designated for data transmission (SO) and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be
received. This byte contains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the
AT25080A/160A/320A/640A, and the serial output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This will reinitialize the serial
communication.
CHIP SELECT: The AT25080A/160A/320A/640A is selected when the CS pin is low.
When the device is not selected, data will not be accepted via the SI pin, and the serial
output pin (SO) will remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the
AT25080A/160A/320A/640A. When the device is selected and a serial sequence is
underway, HOLD can be used to pause the serial communication with the master device
without resetting the serial sequence. To pause, the HOLD pin must be brought low
while the SCK pin is low. To resume serial communication, the HOLD pin is brought high
while the SCK pin is low (SCK may still toggle during HOLD). Inputs to the SI pin will be
ignored while the SO pin is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations
when held high. When the WP pin is brought low and WPEN bit is “1”, all write operations to the status register are inhibited. WP going low while CS is still low will interrupt a
write to the status register. If the internal write cycle has already been initiated, WP
going low will have no effect on any write operation to the status register. The WP pin
function is blocked when the WPEN bit in the status register is "0". This will allow the
user to install the AT25080A/160A/320A/640A in a system with the WP pin tied to
ground and still be able to write to the status register. All WP pin functions are enabled
when the WPEN bit is set to “1”.
5
5082B–SEEPR–1/05
Figure 2. SPI Serial Interface
AT25080A/160A/320A/640A
6
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
Functional
Description
The AT25080A/160A/320A/640A is designed to interface directly with the synchronous
serial peripheral interface (SPI) of the 6805 and 68HC11 series of microcontrollers.
The AT25080A/160A/320A/640A utilizes an 8-bit instruction register. The list of instructions and their operation codes are contained in Table 5. All instructions, addresses, and
data are transferred with the MSB first and start with a high-to-low CS transition.
Table 5. Instruction Set for the AT25080A/160A/320A/640A
Instruction Name
Instruction Format
Operation
WREN
0000 X110
Set Write Enable Latch
WRDI
0000 X100
Reset Write Enable Latch
RDSR
0000 X101
Read Status Register
WRSR
0000 X001
Write Status Register
READ
0000 X011
Read Data from Memory Array
WRITE
0000 X010
Write Data to Memory Array
WRITE ENABLE (WREN): The device will power up in the write disable state when VCC
is applied. All programming instructions must therefore be preceded by a Write Enable
instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write
Disable instruction disables all programming modes. The WRDI instruction is independent of the status of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status Register instruction provides
access to the status register. The READY/BUSY and Write Enable status of the device
can be determined by the RDSR instruction. Similarly, the block write protection bits
indicate the extent of protection employed. These bits are set by using the WRSR
instruction.
Table 6. Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
X
X
X
BP1
BP0
WEN
RDY
Table 7. Read Status Register Bit Definition
Bit
Definition
Bit 0 (RDY)
Bit 0 = “0” (RDY) indicates the device is ready. Bit 0 = “1” indicates the write
cycle is in progress.
Bit 1 (WEN)
Bit 1= “0” indicates the device is not write-enabled. Bit 1 = “1” indicates the
device is write-enabled.
Bit 2 (BP0)
See Table 8 on page 8.
Bit 3 (BP1)
See Table 8 on page 8.
Bits 4 − 6 are “0”s when device is not in an internal write cycle.
Bit 7 (WPEN)
See Table 9 on page 8.
Bits 0 − 7 are “1”s during an internal write cycle.
7
5082B–SEEPR–1/05
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select
one of four levels of protection. The AT25080A/160A/320A/640A is divided into four
array segments. One-quarter, one-half, or all of the memory segments can be protected.
Any of the data within any selected segment will therefore be read only. The block write
protection levels and corresponding status register control bits are shown in Table 8.
Bits BP0, BP1, and WPEN are nonvolatile cells that have the same properties and functions as the regular memory cells (e.g., WREN, tWC, RDSR).
Table 8. Block Write Protect Bits
Status
Register Bits
Array Addresses Protected
Level
BP1
BP0
AT25080A
AT25160A
AT25320A
AT25640A
0
0
0
None
None
None
None
1 (1/4)
0
1
0300
− 03FF
0600
− 07FF
0C00
− 0FFF
1800
− 1FFF
2 (1/2)
1
0
0200
− 03FF
0400
− 07FF
0800
− 0FFF
1000
− 1FFF
3 (All)
1
1
0000
− 03FF
0000
− 07FF
0000
− 0FFF
0000
− 1FFF
The WRSR instruction also allows the user to enable or disable the write protect (WP)
pin through the use of the write protect enable (WPEN) bit. Hardware write protection is
enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is
disabled when either the WP pin is high or the WPEN bit is “0”. When the device is hardware write protected, writes to the status register, including the block protect bits and the
WPEN bit, and the block-protected sections in the memory array are disabled. Writes
are only allowed to sections of the memory that are not block-protected.
NOTE: When the WPEN bit is hardware write protected, it cannot be changed back to
“0” as long as the WP pin is held low.
Table 9. WPEN Operation
8
WPEN
WP
WEN
Protected
Blocks
Unprotected
Blocks
Status
Register
0
X
0
Protected
Protected
Protected
0
X
1
Protected
Writeable
Writeable
1
Low
0
Protected
Protected
Protected
1
Low
1
Protected
Writeable
Protected
X
High
0
Protected
Protected
Protected
X
High
1
Protected
Writeable
Writeable
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
READ SEQUENCE (READ): Reading the AT25080A/160A/320A/640A via the serial
output (SO) pin requires the following sequence. After the CS line is pulled low to select
a device, the read op-code is transmitted via the SI line followed by the byte address to
be read (A15−A0, see Table 10). Upon completion, any data on the SI line will be
ignored. The data (D7−D0) at the specified address is then shifted out onto the SO line.
If only one byte is to be read, the CS line should be driven high after the data comes out.
The read sequence can be continued since the byte address is automatically incremented and data will continue to be shifted out. When the highest address is reached,
the address counter will roll over to the lowest address, allowing the entire memory to be
read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25080A/160A/320A/640A,
two separate instructions must be executed. First, the device must be write enabled via
the WREN instruction. Then a Write (WRITE) instruction may be executed. Also, the
address of the memory location(s) to be programmed must be outside the protected
address field location selected by the block write protection level. During an internal
write cycle, all commands will be ignored except the RDSR instruction.
A Write instruction requires the following sequence. After the CS line is pulled low to
select the device, the WRITE op-code is transmitted via the SI line followed by the byte
address (A15−A0) and the data (D7–D0) to be programmed (See Table 10). Programming will start after the CS pin is brought high. The low-to-high transition of the CS pin
must occur during the SCK low-time immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status
register (RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”,
the write cycle has ended. Only the RDSR instruction is enabled during the write programming cycle.
The AT25080A/160A/320A/640A is capable of a 32-byte page write operation. After
each byte of data is received, the five low-order address bits are internally incremented
by one; the high-order bits of the address will remain constant. If more than 32 bytes of
data are transmitted, the address counter will roll over and the previously written data
will be overwritten. The AT25080A/160A/320A/640A is automatically returned to the
write disable state at the completion of a write cycle.
NOTE: If the device is not write enabled (WREN), the device will ignore the write instruction and will return to the standby state, when CS is brought high. A new CS falling edge
is required to reinitiate the serial communication.
Table 10. Address Key
Address
AT25080A
AT25160A
AT25320A
AT25640A
AN
A9–A0
A10–A0
A11–A0
A12–A0
Don’t
Care Bits
A15–A10
A15–A11
A15–A12
A15–A13
9
5082B–SEEPR–1/05
Timing Diagrams
Figure 3. Synchronous Data Timing (for Mode 0)
t CS
VIH
CS
VIL
t CSH
t CSS
VIH
t WH
SCK
t WL
VIL
tH
t SU
VIH
SI
VALID IN
VIL
tV
VOH
SO
HI-Z
t HO
t DIS
HI-Z
VOL
Figure 4. WREN Timing
Figure 5. WRDI Timing
10
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
Figure 6. RDSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3
2
1
0
SCK
INSTRUCTION
SI
DATA OUT
HIGH IMPEDANCE
SO
7
6
4
5
MSB
Figure 7. WRSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2
1
0
SCK
DATA IN
SI
INSTRUCTION
7
6
5
4
3
HIGH IMPEDANCE
SO
11
5082B–SEEPR–1/05
Figure 8. READ Timing
CS
0
1
2
3
4
5
6
7
8
9 10 11 20 21 22 23 24 25 26 27 28 29 30 31
SCK
BYTE ADDRESS
SI
15 14 13 ...
INSTRUCTION
3
2
1
0
DATA OUT
HIGH IMPEDANCE
7
SO
6
5
4
3
2
1
0
MSB
Figure 9. WRITE Timing
CS
0
1
2
3
4
5
6
7
8
9 10 11 20 21 22 23 24 25 26 27 28 29 30 31
SCK
BYTE ADDRESS
SI
SO
INSTRUCTION
15 14 13 ...
3
2
DATA IN
1
0
7
6
5
4
3
2
1
0
HIGH IMPEDANCE
HOLD Timing
CS
SCK
HOLD
SO
12
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
AT25080A Ordering Information
Ordering Code
Package
Operation Range
AT25080A-10PE-2.7
AT25080AN-10SE-2.7
8P3
8S1
Extended Temperature
(−40°C to 125°C)
AT25080A-10PQ-2.7(1)
AT25080AN-10SQ-2.7(1)
AT25080A-10TQ-2.7(1)
8P3
8S1
8A2
Lead-free/Halogen-free
Extended Temperature
(−40°C to 125°C)
Notes:
1. “Q” designates Green package + RoHS compliant.
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8A2
8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
−2.7
Low Voltage (2.7V to 5.5V)
13
5082B–SEEPR–1/05
AT25160A Ordering Information
Ordering Code
Package
Operation Range
AT25160A-10PE-2.7
AT25160AN-10SE-2.7
8P3
8S1
Extended Temperature
(−40°C to 125°C)
AT25160A-10PQ-2.7(1)
AT25160AN-10SQ-2.7(1)
AT25160A-10TQ-2.7(1)
8P3
8S1
8A2
Lead-free/Halogen-free
Extended Temperature
(−40°C to 125°C)
Notes:
1. “Q” designates Green package + RoHS compliant.
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8A2
8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
−2.7
14
Low Voltage (2.7V to 5.5V)
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
AT25320A Ordering Information
Ordering Code
Package
Operation Range
AT25320A-10PE-2.7
AT25320AN-10SE-2.7
8P3
8S1
Extended Temperature
(−40°C to 125°C)
AT25320A-10PQ-2.7(1)
AT25320AN-10SQ-2.7(1)
AT25320A-10TQ-2.7(1)
8P3
8S1
8A2
Lead-free/Halogen-free
Extended Temperature
(−40°C to 125°C)
Notes:
1. “Q” designates Green package + RoHS compliant.
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8A2
8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
−2.7
Low Voltage (2.7V to 5.5V)
15
5082B–SEEPR–1/05
AT25640A Ordering Information
Ordering Code
Package
Operation Range
AT25640A-10PE-2.7
AT25640AN-10SE-2.7
8P3
8S1
Extended Temperature
(−40°C to 125°C)
AT25640A-10PQ-2.7(1)
AT25640AN-10SQ-2.7(1)
AT25640A-10TQ-2.7(1)
8P3
8S1
8A2
Lead-free/Halogen-free
Extended Temperature
(−40°C to 125°C)
Note:
1. “Q” designates Green package + RoHS compliant.
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S1
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8A2
8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
Options
−2.7
16
Low Voltage (2.7V to 5.5V)
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
Packaging Information
8P3 – PDIP
E
1
E1
N
Top View
c
eA
End View
COMMON DIMENSIONS
(Unit of Measure = inches)
D
e
D1
A2 A
b2
b3
b
4 PLCS
Side View
L
SYMBOL
NOM
MAX
NOTE
2
A
–
–
0.210
A2
0.115
0.130
0.195
b
0.014
0.018
0.022
5
b2
0.045
0.060
0.070
6
b3
0.030
0.039
0.045
6
c
0.008
0.010
0.014
D
0.355
0.365
0.400
3
D1
0.005
–
–
3
E
0.300
0.310
0.325
4
E1
0.240
0.250
0.280
3
e
0.100 BSC
eA
0.300 BSC
L
Notes:
MIN
0.115
0.130
4
0.150
2
1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
01/09/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
8P3, 8-lead, 0.300" Wide Body, Plastic Dual
In-line Package (PDIP)
DRAWING NO.
REV.
8P3
B
17
5082B–SEEPR–1/05
8S1 – JEDEC SOIC
C
1
E
E1
L
N
∅
Top View
End View
e
B
COMMON DIMENSIONS
(Unit of Measure = mm)
A
SYMBOL
A1
D
Side View
MIN
NOM
MAX
A
1.35
–
1.75
A1
0.10
–
0.25
b
0.31
–
0.51
C
0.17
–
0.25
D
4.80
–
5.00
E1
3.81
–
3.99
E
5.79
–
6.20
e
NOTE
1.27 BSC
L
0.40
–
1.27
∅
0˚
–
8˚
Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.
10/7/03
R
18
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TITLE
8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
DRAWING NO.
8S1
REV.
B
AT25080A/160A/320A/640A
5082B–SEEPR–1/05
AT25080A/160A/320A/640A
8A2 – TSSOP
3
2 1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
A
b
D
MIN
2.90
E
e
D
A2
NOTE
3.00
3.10
2, 5
3, 5
E1
4.30
4.40
4.50
A
–
–
1.20
A2
0.80
1.00
1.05
b
0.19
–
0.30
L
4
0.65 BSC
0.45
L1
Notes:
MAX
6.40 BSC
e
Side View
NOM
0.60
0.75
1.00 REF
1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances,
datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15 mm (0.006 in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm
(0.010 in) per side.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the
b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between
protrusion and adjacent lead is 0.07 mm.
5. Dimension D and E1 to be determined at Datum Plane H.
5/30/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
8A2, 8-lead, 4.4 mm Body, Plastic
Thin Shrink Small Outline Package (TSSOP)
DRAWING NO.
8A2
REV.
B
19
5082B–SEEPR–1/05
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© Atmel Corporation 2005. All rights reserved. Atmel ®, logo and combinations thereof are registered trademarks, and Everywhere You Are SM
is a trademark of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.
Printed on recycled paper.
5082B–SEEPR–1/05