HI-SINCERITY Spec. No. : HA200108 Issued Date : 2001.07.01 Revised Date : 2001.11.29 Page No. : 1/3 MICROELECTRONICS CORP. H7806AA H7806BA 3-TERMINAL POSITIVE VOLTAGE REGULATOR Description TO-92 These regulators employ internal current-limiting and thermalshutdown, making them essentially indestructible. They can deliver up to 100mA output current. if the case temperature can keep in Tc=25°C. They are intended as fixed voltage regulators in a wide range of applications including local (on-card) regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The H7806_A used as a Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise. Absolute Maximum Ratings (Ta=25°C) • Input Voltage....................................................................................................................... 35 V • Total Power Dissipation..................................................................................... Internally limited • Operating Temperature Range .......................................................................... 0 °C to +125 °C • Maximum Junction Temperature.....................................................................................+125 °C • Storage Temperature Range........................................................................... -55 °C to +150 °C • Lead Temperature (Soldering 10S)................................................................................ +260 °C Typical Application Schematic Diagram Vin Vin Vout H7806_A 5kΩ 5.7kΩ C1 100Ω C2 1.5kΩ 1.9kΩ 100Ω 576Ω Vout 5pF 3.41kΩ 13kΩ 3.89kΩ 2.23kΩ 7.8kΩ Note: C1 and C2 are required if regulator is located far from power supply filter and load, or oscillation may induced on the loop. 2.84kΩ Gnd H7806AA, H7806BA HSMC Product Specification HI-SINCERITY Spec. No. : HA200108 Issued Date : 2001.07.01 Revised Date : 2001.11.29 Page No. : 2/3 MICROELECTRONICS CORP. Electrical Characteristics Vin=11V, Iout=40mA, 0°C≤Tj≤125°C, Cin=0.33uF, Cout=0.1uF (unless otherwise noted) Symbol Vo Parameter Output Voltage ∆Vo Line Regulation ∆Vo Load Regulation IQ Quiescent Current Quiescent Current ∆IQ Change Vn Output Noise Voltage ∆Vin / ∆Vout Ripple Rejection Peak Output / Isc Short Circuit Current VD Dropout Voltage Symbol Vo Conditions Tj=25°C 1mA≤Io≤70mA 1mA≤Io≤40mA and 8V≤Vin≤21V Tj=25°C, 8V≤Vin≤21V Tj=25°C, 9V≤Vin≤21V Tj=25°C, 1mA≤Io≤40mA Tj=25°C, 1mA≤Io≤100mA Tj=25°C 1mA≤Io≤40mA 9V≤Vin≤21V Ta=25°C, 10Hz≤f≤10KHz 9V≤Vin≤18V, f=120Hz ∆Vo Line Regulation ∆Vo Load Regulation IQ Quiescent Current Quiescent Current ∆IQ Change Vn Output Noise Voltage ∆Vin / ∆Vout Ripple Rejection Peak Output / Isc Short Circuit Current VD Dropout Voltage H7806AA, H7806BA Units V 5.82 - 6.18 44 65 55 6 13 45 59 175 125 40 80 5.5 0.1 1.5 - mA Tj=25°C - 140 - mA Tj=25°C - 1.7 - V Parameter Output Voltage H7806AA Min Typ Max 5.82 6 6.18 5.82 6.18 Conditions Tj=25°C 1mA≤Io≤70mA 1mA≤Io≤40mA and 8V≤Vin≤21V Tj=25°C, 8V≤Vin≤21V Tj=25°C, 9V≤Vin≤21V Tj=25°C, 1mA≤Io≤40mA Tj=25°C, 1mA≤Io≤100mA Tj=25°C 1mA≤Io≤40mA 9V≤Vin≤21V Ta=25°C, 10Hz≤f≤10KHz 9V≤Vin≤18V, f=120Hz H7806BA Min Typ Max 5.75 6 6.25 5.7 6.3 mV mV mA uV dB Units V 5.7 - 6.3 44 65 55 6 13 45 59 175 125 40 80 5.5 0.1 1.5 - mA Tj=25°C - 140 - mA Tj=25°C - 1.7 - V mV mV mA uV dB HSMC Product Specification HI-SINCERITY Spec. No. : HA200108 Issued Date : 2001.07.01 Revised Date : 2001.11.29 Page No. : 3/3 MICROELECTRONICS CORP. TO-92 Dimension α2 A Marking: HSMC Logo B 1 2 Product Series Part Number 3 Date Code Rank α3 C Laser Mark HSMC Logo Product Series D Part Number H I G Ink Mark α1 Style: Pin 1.Output 2.Ground 3.Input E F 3-Lead TO-92 Plastic Package HSMC Package Code: A *: Typical Inches Min. Max. 0.1704 0.1902 0.1704 0.1902 0.5000 0.0142 0.0220 *0.0500 0.1323 0.1480 DIM A B C D E F Millimeters Min. Max. 4.33 4.83 4.33 4.83 12.70 0.36 0.56 *1.27 3.36 3.76 DIM G H I α1 α2 α3 Inches Min. Max. 0.0142 0.0220 *0.1000 *0.0500 *5° *2° *2° Millimeters Min. Max. 0.36 0.56 *2.54 *1.27 *5° *2° *2° Notes: 1.Dimension and tolerance based on our Spec. dated Apr. 25,1996. 2.Controlling dimension: millimeters. 3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material. 4.If there is any question with packing specification or packing method, please contact your local HSMC sales office. Material: • Lead: 42 Alloy ; solder plating • Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 Important Notice: • All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. • HSMC reserves the right to make changes to its products without notice. • HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. • HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: • Head Office (Hi-Sincerity Microelectronics Corp.): 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel: 886-2-25212056 Fax: 886-2-25632712, 25368454 • Factory 1: No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel: 886-3-5983621~5 Fax: 886-3-5982931 H7806AA, H7806BA HSMC Product Specification