Document 1244-1 Shielded Power Inductors High Inductance • High inductance values (220 – 4700 µH) not available in the corresponding LPS series of parts • Rugged construction improves pick and place operation Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over silver. Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Isat (A)5 Irms (A)6 SRF typ4 (MHz) 10% drop 20% drop 30% drop 20°C rise 40°C rise Part number1 Inductance2 ±20% (µH) DCR max3 (Ohms) LPZ3008-224MR_ LPZ3008-334MR_ 220 330 11.5 18.0 9.0 7.0 0.067 0.059 LPZ3010-334MR_ 330 18.5 7.0 0.10 LPZ3015-334MR_ 330 23.0 5.0 0.10 LPZ3314-105MR_ LPZ3314-155MR_ 1000 1500 31.0 44.0 3.0 2.7 0.090 0.080 LPZ4012-335MR_ 3300 65.0 0.95 LPZ4018-155MR_ LPZ4018-185MR_ LPZ4018-225MR_ LPZ4018-335MR_ 1500 1800 2200 3300 25.0 31.5 32.5 48.0 LPZ4414-155MR_ LPZ4414-185MR_ LPZ4414-225MR_ LPZ4414-335MR_ 1500 1800 2200 3300 LPZ5010-105MR_ LPZ5015-335MR_ LPZ5015-475MR_ 0.076 0.066 0.100 0.090 0.145 0.130 0.105 0.115 0.085 0.11 0.11 0.11 0.070 0.095 0.099 0.086 0.100 0.090 0.082 0.060 0.100 0.080 0.074 0.078 0.080 0.050 0.065 2.4 2.3 2.1 1.6 0.095 0.090 0.088 0.082 0.10 0.095 0.094 0.092 0.105 0.10 0.10 0.094 0.080 0.070 0.070 0.055 0.11 0.095 0.090 0.075 26.4 35.0 42.5 56.0 2.2 1.9 1.9 1.3 0.096 0.089 0.082 0.072 0.099 0.094 0.089 0.078 0.10 0.097 0.092 0.083 0.085 0.075 0.065 0.055 0.11 0.10 0.080 0.070 1000 28.0 3.0 0.087 0.096 0.10 0.080 0.11 3300 4700 55.0 80.0 1.7 1.4 0.064 0.062 0.072 0.069 0.076 0.072 0.055 0.045 0.075 0.065 1. When ordering, please specify termination and packaging codes: LPZ3008-334MRC Termination: R = RoHS compliant matte tin over nickel over silver. Special order, added cost: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked 0.073 0.064 2. 3. 4. 5. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. DCR measured on a micro-ohmmeter. SRF measured using an Agilent/HP 8753ES or equivalent. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 1244-1 Revised 01/05/15 Document 1244-2 Shielded Power Inductors – LPZ3008 L vs Current L vs Frequency 800 700 600 600 500 500 400 Inductance (µH) 1000 800 700 Inductance (µH) 1000 330 µH 300 220 µH 200 400 330 µH 300 220 µH 200 100 100 0.0001 0.01 0.001 0.10 Current (A) 0.01 0.1 1 10 Frequency (MHz) Current Derating 120 100 90 80 70 60 50 40 30 20 25°C Percent of rated Current 110 Isat Irms 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 22 – 25 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm Document 1244-2 Revised 01/05/15 Document 1244-3 Shielded Power Inductors – LPZ3010 L vs Current L vs Frequency 800 700 800 700 600 600 500 500 400 Inductance (µH) 1000 Inductance (µH) 1000 330 µH 300 200 100 400 330 µH 300 200 100 0.0001 0.01 0.001 0.10 Current (A) 0.01 0.1 1 10 Frequency (MHz) Typical Current Derating 120 100 90 80 70 60 50 40 30 20 25°C Percent of rated Current 110 Isat Irms 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 25 – 32 mg Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm Document 1244-3 Revised 01/05/15 Document 1244-4 Shielded Power Inductor – LPZ3015 L vs Current L vs Frequency 1000 800 700 Inductance (µH) 600 500 400 330 µH 300 200 100 0.001 0.1 0.01 1.0 Current (A) Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 40 – 45 mg Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm Document 1244-4 Revised 01/05/15 Document 1244-5 Shielded Power Inductors – LPZ3314 Typical L vs Current Typical L vs Frequency Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 44.1 – 46.5 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth Recommended pick and place nozzle OD: 3.3 mm; ID: ≤ 1.65 mm Document 1244-5 Revised 01/05/15 Document 1244-6 Shielded Power Inductors – LPZ4012 Typical L vs Current Typical L vs Frequency Current Derating 0.1535 ±0.003* 3,90 ±0,076 120 110 XXX X 90 80 70 Dash number 60 50 Internal code 30 20 Isat Irms -40 -20 0 20 Winding direction Recommended Land Pattern 0.0433 ±0.004 * 1,10 ±0,10 40 10 0 0.1535 ±0.003* 3,90 ±0,076 0.105 2,66 0.059 1,50 25°C Percent of rated current 100 40 60 80 100 0.110 0.045 2,79 1,15 120 140 Ambient temperature (°C) 0.0305 0,775 0.153 3,89 0.129 3,28 0.060 1,52 are of the case not including * Dimensions the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch / 0,13 mm). 0.173 4,40 Dimensions are in inches mm Weight 54 – 64 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.25 mm thick, 8 mm pocket spacing, 1.32 mm pocket depth Recommended pick and place nozzle OD: 4 mm; ID: ≤ 2 mm Document 1244-6 Revised 01/05/15 Document 1244-7 Shielded Power Inductors – LPZ4018 Typical L vs Current Typical L vs Frequency Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 90 – 100 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.9 mm pocket depth Recommended pick and place nozzle OD: 4 mm; ID: ≤ 2 mm Document 1244-7 Revised 01/05/15 Document 1244-8 Shielded Power Inductors – LPZ4414 Typical L vs Current Typical L vs Frequency Current Derating 0.169 ±0.004* 4,30 ±0,10 100 XXX X 90 80 70 Dash number 60 50 30 20 10 0 0.169 ±0.004* 4,30 ±0,10 Winding direction Internal code 0.0551 max * 1,40 40 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 Recommended Land Pattern 0.128 3,25 0.059 1,50 40 60 80 100 120 140 0.030 typ 0,75 Ambient temperature (°C) 0.185 4,70 0.118 3,00 0.124 3,15 0.030 typ 0,75 0.059 1,50 0.118 3,00 0.185 4,70 are of the case not including * Dimensions the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional 0.005 inch / 0,13 mm). 0.055 1,40 Dimensions are in inches mm Weight 82.3 – 89.8 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.52 mm pocket depth Recommended pick and place nozzle: OD: 4.5 mm; ID: ≤ 2 mm Document 1244-8 Revised 01/05/15 Document 1244-9 Shielded Power Inductor – LPZ5010 Typical L vs Current Typical L vs Frequency Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 70 – 75 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm Document 1244-9 Revised 01/05/15 Document 1244-10 Shielded Power Inductors – LPZ5015 Typical L vs Current Typical L vs Frequency Typical Current Derating 100 90 80 70 60 50 40 30 20 10 0 25°C Percent of rated current 120 110 Isat Irms -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Dimensions are in inches mm Weight 102 – 107 mg Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.57 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm Document 1244-10 Revised 01/05/15