Power DER-97 21.7 w power supply using top246p Datasheet

Design Example Report
Title
21.7 W Power Supply using TOP246P
Specification
Input: 85 - 265 VAC
Output: 48 V / 450 mA
Application
PoE AC Adapter
Author
Power Integrations Applications Department
Document
Number
DER-97
Date
September 12, 2005
Revision
1.0
Summary and Features
•
•
•
•
•
•
•
•
•
Single Sided PC board
Reduced cost and component count
Eliminates two y-capacitors to ground
Eliminates secondary side common mode choke
Eliminates ground wire differential choke
High Efficiency (~ 80 %)
Lower Cost Transformer Construction – no sleeving termination required
Low EMI signature (both radiated and conducted emissions)
Built-in output short circuit protection
The products and applications illustrated herein (including circuits external to the products and transformer
construction) may be covered by one or more U.S. and foreign patents or potentially by pending U.S. and foreign
patent applications assigned to Power Integrations. A complete list of Power Integrations’ patents may be found at
www.powerint.com.
Power Integrations
5245 Hellyer Avenue, San Jose, CA 95138 USA.
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
Table Of Contents
1
2
3
4
Introduction................................................................................................................. 3
Power Supply Specification ........................................................................................ 4
Schematic................................................................................................................... 5
Circuit Operation ........................................................................................................ 6
4.1
General ............................................................................................................... 6
4.2
Description .......................................................................................................... 6
5 Bill of Materials ........................................................................................................... 7
6 Layout......................................................................................................................... 9
7 Transformer Design Spreadsheet ............................................................................ 10
8 Transformer Specification......................................................................................... 13
9 Performance............................................................................................................. 17
9.1
Efficiency........................................................................................................... 17
9.2
Regulation vs. Load........................................................................................... 18
9.3
Regulation vs. Line............................................................................................ 19
9.4
Raw Performance Data ..................................................................................... 20
10
Waveforms............................................................................................................ 21
10.1 Drain Current and Voltage................................................................................. 21
10.2 Output Transient Load Response ..................................................................... 22
10.3 Output Ripple Voltage ....................................................................................... 23
10.4 Switching Ripple................................................................................................ 23
10.5 Line Frequency Ripple ...................................................................................... 24
10.6 Output Voltage Shutdown Profile ...................................................................... 26
11
Thermal Test......................................................................................................... 27
11.1 Thermal Performance........................................................................................ 27
12
Conducted EMI ..................................................................................................... 29
12.1 Conducted EMI Performance ............................................................................ 29
13
Revision History.................................................................................................... 30
Important Notes:
Although this board is designed to satisfy safety isolation requirements, the engineering
prototype has not been agency approved. Therefore, all testing should be performed
using an isolated source to provide power to the prototype board.
Design Reports contain a power supply design specification, schematic, bill of materials,
and transformer documentation. Performance data and typical operation characteristics
are included. Typically only a single prototype has been built.
Page 2 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
1 Introduction
This document is an engineering report describing a Power over Ethernet (PoE) power
supply utilizing TOP246P. The power supply delivers 21.7 W continuous from an input of
85 to 265 VAC.
This document provides complete design information including specification, schematic,
bill of material and transformer design and construction information. The document also
provides performance information.
Figure 1 – Circuit Board - Top View
Figure 2 – Circuit Board - Bottom View
Page 3 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
2 Power Supply Specification
Description
Symbol
Min
VIN
85
VOUT1
VRIPPLE1
IOUT1
47.52
115 VAC
TH(115VAC)
18
ms
230 VAC
TH(230VAC)
60
ms
Input
Voltage
Output
Output Voltage 1
Output Ripple Voltage 1
Output Current 1
Power Down Holdup
Total Output Power
Average Output Power
Full Load Efficiency
Typ
48
0
Max
Units
265
VAC
48.48
480
450
V
mVp-p
mA
POUT1
21.7
W
η
80
%
Comment
± 1%
20 MHz bandwidth
Environmental
Conducted EMI
Meets CISPR22B / EN55022B
Designed to meet IEC950, UL1950
Class II
Safety
Ambient Temperature
Page 4 of 31
TAMB
0
40
o
C
Forced airflow
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
3
21.7 W PoE Adapter
September 12, 2005
Schematic
Figure 3 – Schematic
Page 5 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
4 Circuit Operation
4.1 General
The power supply uses a TOP246P device (U2), with integrated MOSFET and controller,
in an isolated flyback configuration. The circuit also uses the x-pin programmable current
limit feature control the overload power of the power supply and also to minimize
transformer size.
4.2 Description
The input fuse F1 protects the supply against catastrophic failure. Thermistor RT1 limits
the in-rush current during power-up. Diodes D5 – D8 implement a bridge rectifier to
rectify the input mains voltage. Capacitor C22 attenuates the EMI generated by the input
bridge diodes D5-D8.
Inductor L1 is used to attenuate both differential and common mode EMI noise from the
power supply. A large value is used to also prevent any noise filtering through from
networks connector to the power supply output. Capacitor C2 forms part of the EMI
solution by shunting EMI signals generated across the transformer T2. Capacitor C4
decouples the rectified input voltage providing a DC-bus. Resistor R14 programs the
current limit of the TOPSwitch-GX (U2). Resistors R6 and R9 modified this current limit
with input voltage, to maintain a relatively flat output overload profile. Diode D2, R2, C1
and R1 implement an RCD clamp circuit to limit the leakage inductance spike on the
TOPSwitch-GX Drain pin. Diode D3 and C8 implement a bias voltage supply to provide
operating power to the TOPSwitch-GX with integrated PWM, controller and main
switching MOSFET. Capacitors C13 and C14 provide device decoupling with C14 also
programming the startup and auto-restart period of the device. Resistor R13 provides
feedback compensation in conjunction with C14. The inductance of transformer T2
provides the energy storage and conversion component of the circuit. Resistor R41
feeds current to an indicator LED U6, which is illuminated during normal operation.
The 48 V output is rectified and filtered by diodes D1 and D4 and capacitors C5 with C7
provided output decoupling. Resistor R18 and C21 snub high frequency ringing on these
diodes. Resistors R8 and R15 sense the output voltage providing the input signal for the
TL431 (U3) reference. Resistor R41 provides DC bias current (approx. 1 mA) to the U3.
Components R12 and C12 provide compensation for U3, to make sure that it’s frequency
response is limited only to low-frequency signals. Resistor R10 programs the highfrequency gain of the control loop and with opto-diode U5A transmits the feedback signal.
Resistor R42 and C15 provide increase the high frequency gain of the feedback circuit to
improve output ripple rejection. Zener diode VR1 is used due to the high 48 V output
voltage and drops approximately 30 V, to bring the TL431 collector voltage comfortably
within safe levels (i.e. less than 30 V). Opto-transistor U5B feeds the control signal back
to the TOPSwitch-GX.
Page 6 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
5 Bill of Materials
Item Qty.
Ref.
Description
Mfg Part Number
Mfg
1
1 C1
4.7 nF, 1 kV, Thru Hole, Disc Ceramic
5GAD47
Vishay/Sprague
2
1 C2
3
1 C4
440LD22
Vishay
KMX400VB47RM16X
25LL
United Chemi-Con
4
1 C5
5
1 C7
6
1 C8
2.2 nF, Ceramic, Y1
47 uF, 400 V, Electrolytic, Low ESR, 730
mOhm, (16 x 25)
180 uF, 63, Electrolytic, Low ESR, 145
mOhm, (10 x 20)
68 uF, 63, Electrolytic, Low ESR, 340
mOhm, (8 x 12)
10 uF, 50 V, Electrolytic, Gen. Purpose, (5 x
11)
7
2 C12 C15
1.0 uF, 50 V, Ceramic, Z5U
ECU-S1H105MEB
Panasonic
8
1 C13
ECU-S1H104KBB
Panasonic
9
1 C14
100 nF, 50 V, Ceramic, X7R
47 uF, 16 V, Electrolytic, Low ESR, 500
mOhm, (5 x 11.5)
10
1 C21
100 pF, 1 kV, Disc Ceramic
LXZ16VB47RME11LL United Chemi-Con
NIC Components
NCD101K1KVY5F
Corp
11
1 C22
47 nF, 275 VAC, Film, X2
ECQU2A473ML
12
2 D1 D4
13
1 D2
100 V, 1 A, Schottky, DO-41
SB1100
1000 V, 1 A, Rectifier, Glass Passivated, 2
us, DO-41
1N4007GP
14
1 D3
15
LXZ63VB181MJ20LL United Chemi-Con
LXZ63VB68RMH15LL United Chemi-Con
KME50VB10RM5X11
LL
United Chemi-Con
Panasonic
Fairchild
Vishay
Vishay
2 D5 D6
75 V, 300 mA, Fast Switching, DO-35
1N4148
600 V, 1 A, Ultrafast Recovery, 75 ns, DO41
UF4005
16
2 D7 D8
600 V, 1 A, Rectifier, DO-41
1N4005
Vishay
17
1 F1
3,721,100,041
Wickman
18
1 J4
1 A, 250V, Slow, TR5
AC Input Receptacle and Accessory Plug,
PCBM
161-R301SN13
Kobiconn
19
2 J5 J6
R/A, RJ45 Nonshielded, PCBM
RJHS-5080
Amphenol Canada
20
1 L1
19 mH, 0.5 A, Common Mode Choke
ELF15N005A
Panasonic
21
1 L2
3.3 uH, 2.66 A
822LY-3R3M
Toko
22
1 R1
100 k, 5%, 1 W, Metal Oxide
RSF100JB-100K
Yageo
23
1 R2
47 R, 5%, 1/2 W, Carbon Film
CFR-50JB-47R
Yageo
24
1 R6
3 M, 5%, 1/8 W, Carbon Film
CFR-12JB-3M0
Yageo
25
1 R8
182 k, 1%, 1/4 W, Metal Film
MFR-25FBF-182K
Yageo
26
1 R9
2.7 M, 5%, 1/8 W, Carbon Film
CFR-12JB-2M7
Yageo
27
1 R10
3.3 k, 5%, 1/8 W, Carbon Film
CFR-12JB-3K3
Yageo
28
2 R12 R40
1 k, 5%, 1/8 W, Carbon Film
CFR-12JB-1K0
Yageo
29
1 R13
6.8 R, 5%, 1/8 W, Carbon Film
CFR-12JB-6R8
Yageo
Page 7 of 31
Vishay
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
30
1 R14
9.09 k, 1%, 1/4 W, Metal Film
MFR-25FBF-9K09
Yageo
31
1 R15
10 k, 1%, 1/4 W, Metal Film
MFR-25FBF-10K0
Yageo
32
1 R18
10 R, 5%, 1/4 W, Carbon Film
CFR-25JB-10R
Yageo
33
1 R41
2 k, 5%, 1/8 W, Carbon Film
CFR-12JB-2K0
Yageo
34
1 R42
330 R, 5%, 1/8 W, Carbon Film
CFR-12JB-330R
Yageo
35
1 RT1
NTC Thermistor, 30 Ohms, 1.5 A
CL210
36
1 T2
Bobbin, EEL25.4, Horizontal, 10 pins
YW-236-03B
Thermometrics
Yih-Hwa
Enterprises
37
1 U2
38
1 U3
TOPSwitch-GX, TOP246P, DIP-8B
TOP246P
2.495 V Shunt Regulator IC, 2%, 0 to 70C,
TO-92
TL431CLP
Texas Instruments
39
1 U5
Opto coupler, 35 V, CTR 300-600%, 4-DIP ISP817D, PC817X4
Isocom, Sharp
40
1 U6
LED, Green, 5 mm, 565 nm, 30 mcd
SSL-LX5093GD
Lumex Opto
41
1 VR1
30 V, 5%, 500 mW, DO-35
1N5256B
Microsemi
Power Integrations
47 Total
Page 8 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
6 Layout
Figure 4 – PC Board Layout
Page 9 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
7 Transformer Design Spreadsheet
ACDC_TOPSwitchGX_020
INPUT
105; Rev.2.5; Copyright
Power Integrations 2005
ENTER APPLICATION VARIABLES
VACMIN
85
VACMAX
265
fL
50
VO
48
PO
21.7
n
0.86
Z
0.44
VB
12
tC
2.66
CIN
47
ENTER TOPSWITCH-GX VARIABLES
TOP-GX
top246p
Chosen Device
KI
INFO
UNIT
Volts
Volts
Hertz
Volts
Watts
TOP246P
Power
Out
Volts
mSeconds
uFarads
Universal
26W
115 Doubled/230V
34W
Amps
1.158
Amps
132000
Hertz
124000
140000
Hertz
Hertz
Volts
Volts
Volts
Volts
TOPSwitch-GX Switching Frequency: Choose
between 132 kHz and 66 kHz
TOPSwitch-GX Minimum Switching Frequency
TOPSwitch-GX Maximum Switching Frequency
Reflected Output Voltage
TOPSwitch on-state Drain to Source Voltage
Output Winding Diode Forward Voltage Drop
Bias Winding Diode Forward Voltage Drop
Ripple to Peak Current Ratio (0.4 < KRP < 1.0
: 1.0< KDP<6.0)
P/N:
P/N:
PC40EE25.4/32/6.4-Z
*
cm^2
cm
nH/T^2
mm
mm
Core Effective Cross Sectional Area
Core Effective Path Length
Ungapped Core Effective Inductance
Bobbin Physical Winding Width
Safety Margin Width (Half the Primary to
Secondary Creepage Distance)
Number of Primary Layers
Number of Secondary Turns
90
2
1
0.7
0.68
ENTER TRANSFORMER CORE/CONSTRUCTION VARIABLES
Core Type
eel25
Core
EEL25
Bobbin
EEL25_B
OBBIN
AE
0.404
LE
7.34
AL
1420
BW
22.3
M
3
L
NS
External Ilimit reduction factor (KI=1.0 for
default ILIMIT, KI <1.0 for lower ILIMIT)
Use 1% resistor in setting external ILIMIT.
Assumes 0.85 derating at 100 degrees Celsius
Use 1% resistor in setting external ILIMIT
Full (F) frequency option - 132kHz
0.948
F
fSmin
fSmax
VOR
VDS
VD
VDB
KP
TOP_GX_FX_020105.xls: TOPSwitch-GX/FX
Continuous/Discontinuous Flyback
Transformer Design Spreadsheet
Customer
Maximum AC Input Voltage
AC Mains Frequency
Output Voltage (main)
Output Power
Efficiency Estimate
Loss Allocation Factor
Bias Voltage
Bridge Rectifier Conduction Time Estimate
Input Filter Capacitor
0.78
ILIMITMIN
ILIMITMAX
Frequency (F)=132kHz,
(H)=66kHz
fS
OUTPUT
1
21
DC INPUT VOLTAGE PARAMETERS
VMIN
VMAX
81
375
Volts
Volts
Minimum DC Input Voltage
Maximum DC Input Voltage
CURRENT WAVEFORM SHAPE PARAMETERS
DMAX
IAVG
IP
IR
IRMS
0.53
0.31
0.89
0.60
0.45
Amps
Amps
Amps
Amps
Maximum Duty Cycle
Average Primary Current
Peak Primary Current
Primary Ripple Current
Primary RMS Current
Page 10 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
TRANSFORMER PRIMARY DESIGN PARAMETERS
LP
NP
NB
ALG
BM
532
39
5
358
3027
uHenries
BP
BAC
3957
1029
Gauss
Gauss
ur
LG
BWE
OD
2053
0.11
16.3
0.42
mm
mm
mm
INS
0.06
mm
DIA
AWG
0.36
28
mm
AWG
CM
CMA
161
362
Cmils
Cmils/Amp
nH/T^2
Gauss
September 12, 2005
Primary Inductance
Primary Winding Number of Turns
Bias Winding Number of Turns
Gapped Core Effective Inductance
Maximum Flux Density at PO, VMIN
(BM<3000)
Peak Flux Density (BP<4200)
AC Flux Density for Core Loss Curves (0.5 X
Peak to Peak)
Relative Permeability of Ungapped Core
Gap Length (Lg > 0.1 mm)
Effective Bobbin Width
Maximum Primary Wire Diameter including
insulation
Estimated Total Insulation Thickness (= 2 * film
thickness)
Bare conductor diameter
Primary Wire Gauge (Rounded to next smaller
standard AWG value)
Bare conductor effective area in circular mils
Primary Winding Current Capacity (200 < CMA
< 500)
TRANSFORMER SECONDARY DESIGN PARAMETERS (SINGLE OUTPUT EQUIVALENT)
Lumped parameters
ISP
1.63 Amps
Peak Secondary Current
ISRMS
0.77 Amps
Secondary RMS Current
IO
0.45 Amps
Power Supply Output Current
IRIPPLE
0.62 Amps
Output Capacitor RMS Ripple Current
CMS
AWGS
153
Cmils
28
AWG
DIAS
ODS
0.32
0.78
mm
mm
INSS
0.23
mm
VOLTAGE STRESS PARAMETERS
VDRAIN
584
Volts
PIVS
252
Volts
PIVB
65
Volts
TRANSFORMER SECONDARY DESIGN PARAMETERS (MULTIPLE OUTPUTS)
1st output
VO1
48 Volts
IO1
0.452083 Amps
3333
PO1
21.70 Watts
VD1
1 Volts
NS1
21.00
ISRMS1
0.766 Amps
IRIPPLE1
0.62 Amps
PIVS1
252 Volts
CMS1
Page 11 of 31
153
Cmils
Secondary Bare Conductor minimum circular
mils
Secondary Wire Gauge (Rounded up to next
larger standard AWG value)
Secondary Minimum Bare Conductor Diameter
Secondary Maximum Outside Diameter for
Triple Insulated Wire
Maximum Secondary Insulation Wall Thickness
Maximum Drain Voltage Estimate (Includes
Effect of Leakage Inductance)
Output Rectifier Maximum Peak Inverse
Voltage
Bias Rectifier Maximum Peak Inverse Voltage
Output Voltage
Output DC Current
Output Power
Output Diode Forward Voltage Drop
Output Winding Number of Turns
Output Winding RMS Current
Output Capacitor RMS Ripple Current
Output Rectifier Maximum Peak Inverse
Voltage
Output Winding Bare Conductor minimum
circular mils
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
AWGS1
28
DIAS1
ODS1
0.32
0.78
2nd output
VO2
IO2
PO2
VD2
NS2
ISRMS2
IRIPPLE2
PIVS2
0.00
CMS2
AWG
mm
mm
Volts
Amps
Watts
Volts
0.00
0.000
0.00
0
Amps
Amps
Volts
0
Cmils
AWGS2
N/A
AWG
DIAS2
ODS2
N/A
N/A
mm
mm
3rd output
VO3
IO3
PO3
VD3
NS3
ISRMS3
IRIPPLE3
PIVS3
0.00
CMS3
Volts
Amps
Watts
Volts
0.00
0.000
0.00
0
Amps
Amps
Volts
0
Cmils
AWGS3
N/A
AWG
DIAS3
ODS3
N/A
N/A
mm
mm
Total power
Negative Output
Page 12 of 31
21.7
N/A
Watts
September 12, 2005
Wire Gauge (Rounded up to next larger
standard AWG value)
Minimum Bare Conductor Diameter
Maximum Outside Diameter for Triple Insulated
Wire
Output Voltage
Output DC Current
Output Power
Output Diode Forward Voltage Drop
Output Winding Number of Turns
Output Winding RMS Current
Output Capacitor RMS Ripple Current
Output Rectifier Maximum Peak Inverse
Voltage
Output Winding Bare Conductor minimum
circular mils
Wire Gauge (Rounded up to next larger
standard AWG value)
Minimum Bare Conductor Diameter
Maximum Outside Diameter for Triple Insulated
Wire
Output Voltage
Output DC Current
Output Power
Output Diode Forward Voltage Drop
Output Winding Number of Turns
Output Winding RMS Current
Output Capacitor RMS Ripple Current
Output Rectifier Maximum Peak Inverse
Voltage
Output Winding Bare Conductor minimum
circular mils
Wire Gauge (Rounded up to next larger
standard AWG value)
Minimum Bare Conductor Diameter
Maximum Outside Diameter for Triple Insulated
Wire
Total Power for Multi-output section
If negative output exists enter Output number;
eg: If VO2 is negative output, enter 2
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
8 Transformer Specification
Transformer Construction
Electrical Diagram
Winding Order
Core Information
Core Type
Core Material
Estimated Gap length, mm
Gapped Effective Inductance, nH/t^2
Primary Inductance, uH
Page 13 of 31
eel25
NC-2H or Equivalent
0.110
358
532
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
Bobbin Information (Manual Input)
Bobbin Reference
Bobbin Orientation
Number of Primary pins
Number of Secondary pins
Margin on Left, mm
Margin on Right, mm
Generic, 5 pri. + 5 sec.
Horizontal
5
5
3.0
3.0
Primary Winding (Manual Input)
Parameter
Number of Turns
Wire Size, AWG
Filar
Layers
Start Pin(s)
Termination Pin(s)
39
28
1
0.88
5
3
BIAS Winding (Manual Input)
Parameter
Number of Turns
Wire Size, AWG
Filar
Layers
Start Pin(s)
Termination Pin(s)
6
28
1
0.13
1
2
Shield Information
Parameter
Number of Turns
Wire Size, AWG
Filar
Layers
Start Pin(s)
Termination Pin(s)
Value
Primary
Cancellation
20
28
2
0.90
NC
3,4
Secondary Winding (Manual Input)
Parameter
Spec Voltage, V
Spec Current, A
Actual Voltage, V
Number of Turns
Wire Size, AWG
Filar
Layers
Start Pin(s)
Termination Pin(s)
Page 14 of 31
Section 1
22
28
2
0.99
3,4
NC
Output 1
48.00
0.45
48.00
21
28
2
0.94
6
7
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
Winding Instruction
Use 3.0 mm margin (item [3]) on the left side. Use 3.0 mm margin (item [3]) on the right
side.
Cancellation Shield Winding
Start on pin(s) 3,4 and wind 22 turns (x 2 filar) of item [6]. in exactly 1 layer. Leave this
end of cancellation shield winding not connected. Bend the end 90 deg and cut the wire in
the middle of the bobbin.
Add 1 layer of tape, item [4], to secure the winding in place.
Primary Winding
Start on pin(s) 5 and wind 39 turns of item [6] in 1.00 layer(s) from left to right. Finish
winding on pin(s) 3.
Add 1 layer of tape, item [4], for insulation.
Bias Winding
Start on pin(s) 1 and wind 6.0 turns (x 1 filar) of item [6]. Spread the winding evenly
across entire bobbin. Finish on pin(s) 2.
Add 1 layer of tape, item [4], for insulation.
Primary Balanced Shield Winding
Start on any (temp) pin on the secondary side and wind 20 turns (x 2 filar) of item [6].
Spread the winding evenly across entire bobbin. Finish this winding on pin(s) 3,4.
Cut out wire connected to temp pin on secondary side. Leave this end of primary shield
winding not connected. Bend the end 90 deg and cut the wire in the middle of the bobbin.
Add 3 layers of tape, item [4], for insulation.
Secondary Winding
Start on pin(s) 6 and wind 21 turns (x 2 filar) of item [6]. Spread the winding evenly
across entire bobbin. Finish on pin(s) 7.
Add 2 layers of tape, item [4], for insulation.
Core Assembly
Assemble and secure core halves. Item [1].
Varnish
Dip varnish uniformly in item [5]. Do not vacuum impregnate.
Comments
1.
Pins 8 through 10 on the secondary side are not connected to any
electrical node.
2.
Pins 3 and 4 should be electrically connected
Materials
Item
[1]
[2]
[3]
[4]
[5]
[6]
Page 15 of 31
Description
Core: eel25, NC-2H or Equivalent,
gapped for ALG of 358 nH/t^2
Bobbin: Generic, 5 pri. + 5 sec.
Tape: Polyester web 3.0 mm wide
Barrier Tape: Polyester film 22.30 mm
wide
Varnish
Magnet Wire: 28 AWG, Solderable
Double Coated
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
Electrical Test Specifications
Parameter
Condition
Electrical Strength, VAC
60 Hz 1 minute, from pins
3 - 5 to pins 6 - 10.
Nominal Primary Inductance, Measured at 1 V pk-pk,
uH
typical switching
frequency, between pin 3
to pin 5, with all other
Windings open.
Primary Leakage, uH
Measured between Pin 3
to Pin 5, with all other
Windings shorted.
Page 16 of 31
September 12, 2005
Spec
3000
586 +/- 10%
17.57 Goal
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
9 Performance
9.1
Efficiency
E fficiency vs Line/Load
90%
Efficiency (%)
80%
70%
85 VAC
115 VAC
60%
230 VAC
265 VAC
50%
40%
0
5
10
15
Pout (W)
20
25
Figure 5 – Efficiency vs. Input Voltage and Output Load, Room Temperature
Page 17 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
9.2
21.7 W PoE Adapter
September 12, 2005
Regulation vs. Load
R e g u la tio n v s L o a d
101. 0%
85 V A C
1 15 V A C
Regulation (%)
100. 5%
2 30 V A C
2 65 V A C
100. 0%
99. 5%
99. 0%
0
5
10
15
20
25
P o u t (W )
Figure 6 – Output Regulation vs. Output Load, Room Temperature
Page 18 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
9.3
21.7 W PoE Adapter
September 12, 2005
Regulation vs. Line
Regulation vs Line
Regulation (%)
101.0%
Full Load
100.5%
No Load
100.0%
99.5%
99.0%
50
100
150
200
250
300
Vin (VAC)
Figure 7 – Output Regulation vs. Input Line Voltage, Room Temperature
Page 19 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
9.4 Raw Performance Data
Load was applied at the end of a 1 ft long Ethernet cable connected to the connector J6.
The load was applied using an electronic load. The output voltage was measurement at
the end of this cable.
Vin
(DC)
Pin
(A)
Vout1
(V)
Iout1
(A)
86.79
86.42
86.8
86.39
85.95
85.46
85.22
0.828
3.802
6.432
12.573
18.42
24.24
27.03
48
48
48
48
48
47.9
47.9
0
0.05
0.1
0.2
0.3
0.4
0.45
100.0%
100.0%
100.0%
100.0%
100.0%
99.8%
99.8%
0.010
0.044
0.074
0.146
0.214
0.284
0.317
0.0%
63.1%
74.6%
76.4%
78.2%
79.0%
79.7%
0.000
0.001
0.001
0.002
0.002
0.003
0.004
0.0
2.4
4.8
9.6
14.4
19.2
21.6
115.83
115.74
115.13
114.31
113.9
113.81
113.54
0.7734
3.2452
6.629
12.346
17.985
23.794
26.831
48
48
48
48
48
47.9
47.9
0
0.05
0.1
0.2
0.3
0.4
0.45
100.0%
100.0%
100.0%
100.0%
100.0%
99.8%
99.8%
0.007
0.028
0.058
0.108
0.158
0.209
0.236
0.0%
74.0%
72.4%
77.8%
80.1%
80.5%
80.3%
0.000
0.000
0.001
0.001
0.001
0.002
0.002
0.0
2.4
4.8
9.6
14.4
19.2
21.6
230.56
230.1
230
229.41
229.71
229.39
228.87
0.9012
3.878
6.78
12.405
18.825
23.478
26.994
48
48
48
48
48
47.9
47.9
0
0.05
0.1
0.2
0.3
0.4
0.45
100.0%
100.0%
100.0%
100.0%
100.0%
99.8%
99.8%
0.004
0.017
0.029
0.054
0.082
0.102
0.118
0.0%
61.9%
70.8%
77.4%
76.5%
81.6%
79.9%
0.000
0.000
0.000
0.000
0.000
0.000
0.001
0.0
2.4
4.8
9.6
14.4
19.2
21.6
265
265.46
265.67
264.92
264.66
264.4
263.88
0.9906
4.317
7.205
12.731
19.287
24.105
26.931
48
48
48
48
48
47.9
47.9
0
0.05
0.1
0.2
0.3
0.4
0.45
100.0%
100.0%
100.0%
100.0%
100.0%
99.8%
99.8%
0.004
0.016
0.027
0.048
0.073
0.091
0.102
0.0%
55.6%
66.6%
75.4%
74.7%
79.5%
80.0%
0.000
0.000
0.000
0.000
0.000
0.000
0.000
0.0
2.4
4.8
9.6
14.4
19.2
21.6
48
47.9
0.1
0.0%
-0.2%
0.2%
100.0%
99.8%
0.2%
Max
Min
Delta
Page 20 of 31
%Vout1
(%)
Iin
(A)
0.317
0.004
0.313
Eff
(%)
Iin
(A)
81.6%
0.0%
81.6%
Pout
(W)
21.6
2.4
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
10 Waveforms
10.1 Drain Current and Voltage
Figure 8 – 85 VAC, full load
Upper Ch3: Drain Voltage 100 V,
Lowr Ch4: Drain Current 0.5 A / Div,
2 µs / div
Figure 9 – 115 VAC, full load
Upper Ch3: Drain Voltage 100 V,
Lowr Ch4: Drain Current 0.5 A / Div,
2 µs / div
Figure 10 – 230 VAC, full load
Upper Ch3: Drain Voltage 200 V,
Lowr Ch4: Drain Current 0.5 A / Div,
2 µs / div
Figure 11 – 265 VAC, full load
Upper Ch3: Drain Voltage 200 V,
Lowr Ch4: Drain Current 0.5 A / Div,
2 µs / div
Page 21 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
10.2 Output Transient Load Response
Figure 12 – 115 VAC, (48 V 0.23 A to 0.45 A step)
48 V Output Voltage
200 mV / Div, 5 ms / div
Page 22 of 31
Figure 13 – 230 VAC, (48 V 0.23 A to 0.45 A step)
48 V Output Voltage
200 mV / Div, 5 ms / div
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
10.3 Output Ripple Voltage
It can be seen from the waveforms below that the power supply comfortably meets the
output ripple specifications. This is possible even without the need for an output inductor.
Measurements made at the end of an Ethernet cable connected to J6. The voltage
measurement included a 0.1 uF ceramic capacitor in parallel with a 1 uF / 50 V
electrolytic capacitor, at point of measurement (end of the cable).
10.4 Switching Ripple
Figure 14 – 85 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 µs / div
Page 23 of 31
Figure 15 – 115 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 µs / div
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
Figure 16 – 230 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 µs / div
September 12, 2005
Figure 17 – 265 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 µs / div
10.5 Line Frequency Ripple
Figure 18 – 85 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 ms / div
Page 24 of 31
Figure 19 – 115 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 ms / div
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
Figure 20 – 230 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 ms / div
Page 25 of 31
September 12, 2005
Figure 21 – 265 VAC, Full Load
CH1: 48 V Output Ripple, 200 mV,
CH3: Drain Voltage, 200 V,
5 ms / div
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
10.6 Output Voltage Shutdown Profile
The results below show that the power supply comfortably meets the power-supply holdup requirements of the specification.
Figure 22 – Shutdown Profile at Full Load, 120 VAC
Upper Ch1: 48 V output, 10 V / div,
Lower Ch3: Bus Voltage 100 V / div,
20 ms / div.
Page 26 of 31
Figure 23 – Shutdown Profile at Full Load, 120 VAC
Upper Ch1: 48 V output, 10 V / div,
Lower Ch3: Bus Voltage 100 V / div,
20 ms / div.
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
11 Thermal Test
The thermal measurements were made at 85 VAC (which corresponds to the worst case
efficiency of the power supply). Ambient temperature of the oven was 40’C. The power
supply was connected to an electronic load (external to the chamber). A cardboard box
was used around the power supply to prevent significant airflow. The whole setup was
saturated at 40’C for an hour before beginning measurements.
11.1 Thermal Performance
Temperature Vs Time
140
Temperature ('C)
120
Ch2 - Amb1
100
Ch3 - D1
80
Ch4 - TOP246P
60
Ch5 - Case
40
20
0
1
10
100
Time (min)
Figure 24 – Thermal Performance of Key Power Supply Components
Page 27 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
Delta
Time
0.1
0.9
1
2
4
8
16
32
64
128
Ch2
Amb1
40
40
40
40
40
41
42
43
43
43
Ch3
D1
40
52
57
61
65
72
82
83
85
85
September 12, 2005
Ch4
Ch5
TOP246P
CASE
40
40
55
40
59
41
70
43
73
45
87
51
99
60
105
64
107
65
107
65
Figure 25 – Raw Test Data
Page 28 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
12 Conducted EMI
The EMI was tested with and without the output connected to earth-ground. Load was
connected through an Ethernet cable to a resistive load (100 ohms).
12.1 Conducted EMI Performance
Figure 26 – 115 VAC - N1 - grounded output - fullload
Figure 27 – 115 VAC - L1 - grounded output - fullload
Figure 28 – 230 VAC - N1 – grounded output - fullload
Figure 29 – 230 VAC - L1 – grounded output - fullload
Page 29 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
13 Revision History
Date
September 12, 2005
Page 30 of 31
Author
RM
Revision
1.0
Description & changes
First Release
Reviewed
VC / AM
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
DER-97
21.7 W PoE Adapter
September 12, 2005
For the latest updates, visit our Web site: www.powerint.com
Power Integrations may make changes to its products at any time. Power Integrations has no liability arising from your
use of any information, device or circuit described herein nor does it convey any license under its patent rights or the
rights of others. POWER INTEGRATIONS MAKES NO WARRANTIES HEREIN AND SPECIFICALLY DISCLAIMS
ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
PATENT INFORMATION
The products and applications illustrated herein (including circuits external to the products and transformer
construction) may be covered by one or more U.S. and foreign patents or potentially by pending U.S. and foreign
patent applications assigned to Power Integrations. A complete list of Power Integrations’ patents may be found at
www.powerint.com.
The PI Logo, TOPSwitch, TinySwitch, LinkSwitch, and EcoSmart are registered trademarks of Power
Integrations. PI Expert and DPA-Switch are trademarks of Power Integrations.
© Copyright 2004, Power Integrations.
Power Integrations Worldwide Sales Support Locations
WORLD HEADQUARTERS
5245 Hellyer Avenue,
San Jose, CA 95138, USA
Main:
+1-408-414-9200
Customer Service:
Phone: +1-408-414-9665
Fax:
+1-408-414-9765
e-mail:
[email protected]
GERMANY
Rueckertstrasse 3,
D-80336, Munich, Germany
Phone: +49-895-527-3910
Fax:
+49-895-527-3920
e-mail: [email protected]
JAPAN
Keihin-Tatemono 1st Bldg.
12-20 Shin-Yokohama,
2-Chome,
Kohoku-ku, Yokohama-shi,
Kanagawa 222-0033, Japan
Phone: +81-45-471-1021
Fax:
+81-45-471-3717
e-mail:
[email protected]
TAIWAN
17F-3, No. 510,
Chung Hsiao E. Rd., Sec. 5,
Taipei, Taiwan 110, R.O.C.
Phone: +886-2-2727-1221
Fax:
+886-2-2727-1223
e-mail:
[email protected]
CHINA (SHANGHAI)
Rm 807, Pacheer,
Commercial Centre,
555 Nanjing West Road,
Shanghai, 200041, China
Phone: +86-21-6215-5548
Fax:
+86-21-6215-2468
e-mail:
[email protected]
INDIA (TECHNICAL SUPPORT)
Innovatech
261/A, Ground Floor
7th Main, 17th Cross,
Sadashivanagar
Bangalore, India, 560080
Phone: +91-80-5113-8020
Fax:
+91-80-5113-8023
e-mail: [email protected]
KOREA
8th Floor, DongSung Bldg.
17-8 Yoido-dong,
Youngdeungpo-gu,
Seoul, 150-874, Korea
Phone: +82-2-782-2840
Fax:
+82-2-782-4427
e-mail:
[email protected]
UK (EUROPE & AFRICA
HEADQUARTERS)
1st Floor, St. James’s House
East Street
Farnham, Surrey GU9 7TJ
United Kingdom
Phone: +44-1252-730-140
Fax:
+44-1252-727-689
e-mail: [email protected]
CHINA (SHENZHEN)
Rm# 1705, Bao Hua Bldg.
1016 Hua Qiang Bei Lu,
Shenzhen, Guangdong,
518031, China
Phone: +86-755-8367-5143
Fax:
+86-755-8377-9610
e-mail:
[email protected]
ITALY
Via Vittorio Veneto 12, Bresso,
Milano,
20091, Italy
Phone: +39-028-928-6001
Fax: +39-028-928-6009
e-mail: [email protected]
SINGAPORE
51 Newton Road,
#15-08/10 Goldhill Plaza,
Singapore, 308900
Phone: +65-6358-2160
Fax:
+65-6358-2015
e-mail:
[email protected]
m
APPLICATIONS HOTLINE
World Wide +1-408-414-9660
APPLICATIONS FAX
World Wide +1-408-414-9760
ER or EPR template – Rev 3.6 – Single sided
Page 31 of 31
Power Integrations
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
Similar pages