TI1 MSP430F6725AIPZR Mixed-signal microcontroller Datasheet

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
MSP430F673xA, MSP430F672xA Mixed-Signal Microcontrollers
1 Device Overview
1.1
Features
1
• Low Supply-Voltage Range:
3.6 V Down to 1.8 V
• Ultra-Low Power Consumption
– Active Mode (AM):
All System Clocks Active
265 µA/MHz at 8 MHz, 3.0 V, Flash Program
Execution (Typical)
140 µA/MHz at 8 MHz, 3.0 V, RAM Program
Execution (Typical)
– Standby Mode (LPM3):
Real-Time Clock (RTC) With Crystal, Watchdog,
and Supply Supervisor Operational, Full RAM
Retention, Fast Wakeup:
1.7 µA at 2.2 V, 2.5 µA at 3.0 V (Typical)
– Off Mode (LPM4):
Full RAM Retention, Supply Supervisor
Operational, Fast Wakeup:
1.6 µA at 3.0 V (Typical)
– Shutdown RTC Mode (LPM3.5):
Shutdown Mode, Active RTC With Crystal:
1.24 µA at 3.0 V (Typical)
– Shutdown Mode (LPM4.5):
0.78 µA at 3.0 V (Typical)
• Wakeup From Standby Mode in 3 µs (Typical)
• 16-Bit RISC Architecture, Extended Memory, up to
25-MHz System Clock
• Flexible Power Management System
– Fully Integrated LDO With Programmable
Regulated Core Supply Voltage
– Supply Voltage Supervision, Monitoring, and
Brownout
– System Operation From up to Two Auxiliary
Power Supplies
• Unified Clock System
– FLL Control Loop for Frequency Stabilization
– Low-Power Low-Frequency Internal Clock
Source (VLO)
– Low-Frequency Trimmed Internal Reference
Source (REFO)
– 32-kHz Crystals (XT1)
1.2
•
•
• One 16-Bit Timer With Three Capture/Compare
Registers
• Three 16-Bit Timers With Two Capture/Compare
Registers Each
• Enhanced Universal Serial Communication
Interfaces (eUSCIs)
– eUSCI_A0, eUSCI_A1, and eUSCI_A2
• Enhanced UART Supports Automatic BaudRate Detection
• IrDA Encoder and Decoder
• Synchronous SPI
– eUSCI_B0
• I2C With Multiple Slave Addressing
• Synchronous SPI
• Password-Protected RTC With Crystal Offset
Calibration and Temperature Compensation
• Separate Voltage Supply for Backup Subsystem
– 32-kHz Low-Frequency Oscillator (XT1)
– Real-Time Clock
– Backup Memory (4 × 16 Bits)
• Three 24-Bit Sigma-Delta Analog-to-Digital
Converters (ADCs) With Differential PGA Inputs
• Integrated LCD Driver With Contrast Control for up
to 320 Segments in 8-Mux Mode
• Hardware Multiplier Supports 32-Bit Operations
• 10-Bit 200-ksps ADC
– Internal Reference
– Sample-and-Hold, Autoscan Feature
– Up to Six External Channels and Two Internal
Channels, Including Temperature Sensor
• Three-Channel Internal DMA
• Serial Onboard Programming, No External
Programming Voltage Needed
• Table 3-1 Summarizes the Available Family
Members
• Available in 100-Pin and 80-Pin LQFP Packages
• For Complete Module Descriptions, See the
MSP430x5xx and MSP430x6xx Family User's
Guide (SLAU208)
Applications
Single-Phase Electronic Watt-Hour Meters
Energy Monitoring
•
Utility Metering
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
1.3
www.ti.com
Description
The Texas Instruments MSP430™ family of ultra-low-power microcontrollers consists of several devices
featuring different sets of peripherals targeted for various applications. The architecture, combined with
extensive low-power modes, is optimized to achieve extended battery life in portable measurement
applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators
that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to
wake up from low-power modes to active mode in 3 µs (typical).
The MSP430F673xA and MSP430F672xA devices are microcontrollers with three high-performance 24-bit
sigma-delta ADCs, a 10-bit ADC, four eUSCIs (three eUSCI_A modules and one eUSCI_B module), four
16-bit timers, a hardware multiplier, a DMA module, an RTC module with alarm capabilities, an LCD driver
with integrated contrast control, an auxiliary supply system, and up to 72 I/O pins in the 100‑pin devices
and 52 I/O pins in the 80‑pin devices.
Device Information (1)
PACKAGE
BODY SIZE (2)
MSP430F6736APZ
LQFP (100)
14 mm × 14 mm
MSP430F6736APN
LQFP (80)
12 mm × 12 mm
PART NUMBER
(1)
(2)
2
For the most current part, package, and ordering information, see the Package Option Addendum in ,
or see the TI web site at www.ti.com.
The sizes shown here are approximations. For the package dimensions with tolerances, see the
Mechanical Data in .
Device Overview
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
1.4
SLASE46 – FEBRUARY 2015
Functional Block Diagrams
Figure 1-1 shows the functional block diagram for all device variants in the PZ package.
XIN
DVCC DVSS
XOUT
AVCC AVSS
AUX1 AUX2 AUX3
PA
P1.x P2.x
RST/NMI
PB
P3.x P4.x
PC
P5.x P6.x
P7.x
PD
P8.x
PE
P9.x
(32kHz)
ACLK
Unified
Clock
System
SMCLK
128KB
96KB
64KB
32KB
16KB
8KB
4KB
2KB
1KB
Flash
RAM
MCLK
SYS
Watchdog
Port
Mapping
Controller
MPY32
CRC16
I/O Ports
P1/P2
2×8 I/Os
Interrupt
& Wakeup
I/O Ports
P3/P4
2×8 I/Os
I/O Ports
P5/P6
2×8 I/Os
I/O Ports
P7/P8
2×8 I/Os
I/O Ports
P9
1×4 I/O
PA
1×16 I/Os
PB
1×16 I/Os
PC
1×16 I/Os
PD
1×16 I/Os
PE
1×4 I/O
CPUXV2
and
Working
Registers
(25MHz)
EEM
(S: 3+1)
PMM
Auxiliary
Supplies
JTAG/
SBW
Interface/
LDO
SVM/SVS
BOR
Port PJ
SD24_B
ADC10_A
LCD_C
REF
3 Channel
2 Channel
10 Bit
200 KSPS
8MUX
Up to 320
Segments
Reference
1.5V, 2.0V,
2.5V
RTC_C
Timer_A
3 CC
Registers
PJ.x
eUSCI_A0
eUSCI_A1
eUSCI_A2
TA1
TA2
TA3
TA0
Timer_A
2 CC
Registers
eUSCI_B0
(SPI, I2C)
(UART,
IrDA,SPI)
DMA
3 Channel
Figure 1-1. Functional Block Diagram - MSP430F673xAIPZ and MSP430F672xAIPZ
Figure 1-2 shows the functional block diagram for all device variants in the PN package.
XIN
XOUT
DVCC DVSS
AVCC AVSS
AUX1 AUX2 AUX3
PA
P1.x P2.x
RST/NMI
PB
P3.x P4.x
PC
P5.x P6.x
(32kHz)
ACLK
Unified
Clock
System
SMCLK
MCLK
128KB
96KB
64KB
32KB
16KB
8KB
4KB
2KB
1KB
Flash
RAM
SYS
DMA
Watchdog
3 Channel
Port
Mapping
Controller
CRC16
MPY32
I/O Ports
P1/P2
2×8 I/Os
Interrupt
& Wakeup
I/O Ports
P3/P4
2×8 I/Os
I/O Ports
P5/P6
2×8 I/Os
PA
1×16 I/Os
PB
1×16 I/Os
PC
1×16 I/Os
TA0
TA1
TA2
TA3
eUSCI_A0
eUSCI_A1
eUSCI_A2
Timer_A
3 CC
Registers
Timer_A
2 CC
Registers
(UART,
IrDA,SPI)
CPUXV2
and
Working
Registers
(25MHz)
EEM
(S: 3+1)
JTAG/
SBW
Interface/
Port PJ
PMM
Auxiliary
Supplies
LDO
SVM/SVS
BOR
SD24_B
3 Channel
2 Channel
ADC10_A
10 Bit
200 KSPS
LCD_C
8MUX
Up to 320
Segments
REF
Reference
1.5V, 2.0V,
2.5V
RTC_C
eUSCI_B0
(SPI, I2C)
PJ.x
Figure 1-2. Functional Block Diagram - MSP430F673xAIPN and MSP430F672xAIPN
Device Overview
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
3
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
Device Overview ......................................... 1
6.2
CPU
1.1
Features .............................................. 1
6.3
Instruction Set ....................................... 70
1.2
Applications ........................................... 1
6.4
Operating Modes .................................... 71
1.3
Description ............................................ 2
6.5
Interrupt Vector Addresses.......................... 72
1.4
Functional Block Diagrams ........................... 3
6.6
Bootstrap Loader (BSL) ............................. 73
Revision History ......................................... 4
Device Comparison ..................................... 5
Terminal Configuration and Functions .............. 6
6.7
JTAG Operation ..................................... 73
6.8
Flash Memory ....................................... 74
69
6.9
RAM ................................................. 74
Backup RAM ........................................ 74
4.1
Pin Diagrams ......................................... 6
6.10
4.2
Pin Attributes ........................................ 10
4.3
Signal Descriptions .................................. 20
4.4
Pin Multiplexing
4.5
Connection of Unused Pins ......................... 31
.......................................... 75
6.12 Device Descriptors (TLV) .......................... 115
6.13 Memory ............................................ 117
6.14 Identification........................................ 132
Applications, Implementation, and Layout ...... 133
Device and Documentation Support .............. 134
8.1
Device Support..................................... 134
8.2
Documentation Support ............................ 137
8.3
Related Links ...................................... 138
8.4
Community Resources............................. 138
8.5
Trademarks ........................................ 138
8.6
Electrostatic Discharge Caution ................... 138
8.7
Export Control Notice .............................. 138
8.8
Glossary............................................ 139
.....................................
5.2
5.3
5.4
5.5
5.6
5.7
........................
ESD Ratings ........................................
Recommended Operating Conditions ...............
Absolute Maximum Ratings
32
7
8
32
32
Active Mode Supply Current Into VCC Excluding
External Current ..................................... 34
Low-Power Mode Supply Currents (Into VCC)
Excluding External Current.......................... 35
Low-Power Mode With LCD Supply Currents (Into
VCC) Excluding External Current .................... 36
Timing and Switching Characteristics ............... 37
Detailed Description ................................... 69
6.1
6.11
31
Specifications ........................................... 32
5.1
6
.................................................
Overview
............................................
69
9
Peripherals
Mechanical, Packaging, and Orderable
Information ............................................. 139
2 Revision History
4
DATE
REVISION
NOTES
February 2015
*
Initial Release
Revision History
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
3 Device Comparison
Table 3-1 summarizes the available family members.
Table 3-1. Device Comparison (1)
(2)
eUSCI
CHANNEL
A:
UART, IrDA,
SPI
CHANNEL
B:
SPI, I2C
I/O
PACKAGE
TYPE
3, 2, 2, 2
3
1
72
100 PZ
3, 2, 2, 2
3
1
72
100 PZ
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
3
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
2
3
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
16
1
3
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6726AIPZ
128
8
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6725AIPZ
128
4
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6724AIPZ
96
4
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6723AIPZ
64
4
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6721AIPZ
32
2
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6720AIPZ
16
1
2
6 ext, 2 int
3, 2, 2, 2
3
1
72
100 PZ
MSP430F6736AIPN
128
8
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6735AIPN
128
4
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6734AIPN
96
4
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6733AIPN
64
4
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6731AIPN
32
2
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6730AIPN
16
1
3
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6726AIPN
128
8
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6725AIPN
128
4
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6724AIPN
96
4
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6723AIPN
64
4
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6721AIPN
32
2
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
MSP430F6720AIPN
16
1
2
3 ext, 2 int
3, 2, 2, 2
3
1
52
80 PN
DEVICE
FLASH
(KB)
SRAM
(KB)
SD24_B
CONVERTERS
ADC10_A
CHANNELS
MSP430F6736AIPZ
128
8
3
6 ext, 2 int
MSP430F6735AIPZ
128
4
3
6 ext, 2 int
MSP430F6734AIPZ
96
4
3
MSP430F6733AIPZ
64
4
MSP430F6731AIPZ
32
MSP430F6730AIPZ
(1)
(2)
(3)
Timer_A
(3)
For the most current package and ordering information, see the Package Option Addendum in , or see the TI website at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
Each number in the sequence represents an instantiation of Timer_A with its associated number of capture compare registers and PWM
output generators available. For example, a number sequence of 3, 5 would represent two instantiations of Timer_A, the first
instantiation having 3 and the second instantiation having 5 capture compare registers and PWM output generators, respectively.
Device Comparison
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
5
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
4 Terminal Configuration and Functions
4.1
Pin Diagrams
P6.1/S18
P6.2/S17
P6.3/S16
P6.4/S15
P6.5/S14
P6.6/S13
P6.7/S12
P7.0/S11
P7.1/S10
P7.2/S9
P7.3/S8
P7.4/S7
P7.5/S6
P7.6/S5
P7.7/S4
P8.0/S3
P8.1/S2
P8.2/S1
P8.3/S0
TEST/SBWTCK
PJ.0/SMCLK/TDO
PJ.1/MCLK/TDI/TCLK
PJ.2/ADC10CLK/TMS
PJ.3/ACLK/TCK
RST/NMI/SBWTDIO
Figure 4-1 shows the pin assignments for the 100-pin PZ package. See Table 4-1 for differences between
the MSP430F673xA and MSP430F672xA devices in this package.
SD0P0
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
1
75
DVSS
SD0N0
2
74
DVSYS
SD1P0
3
73
P6.0/S19
SD1N0
4
72
P5.7/S20
SD2P0
5
71
P5.6/S21
SD2N0
6
70
P5.5/S22
VREF
7
69
P5.4/S23
AVSS
8
68
P5.3/S24
AVCC
9
67
P5.2/S25
VASYS
10
66
P5.1/S26
P9.1/A5
11
65
P5.0/S27
P9.2/A4
12
64
P4.7/S28
P9.3/A3
13
63
P4.6/S29
P1.0/PM_TA0.0/VeREF-/A2
14
62
P4.5/S30
P1.1/PM_TA0.1/VeREF+/A1
15
61
P4.4/S31
P1.2/PM_UCA0RXD/PM_UCA0SOMI/A0
16
60
P4.3/S32
P1.3/PM_UCA0TXD/PM_UCA0SIMO/R03
17
59
P4.2/S33
AUXVCC2
18
58
P4.1/S34
AUXVCC1
19
57
P4.0/S35
VDSYS
20
56
P3.7/PM_SD2DIO/S36
DVCC
21
55
P3.6/PM_SD1DIO/S37
DVSS
22
54
P3.5/PM_SD0DIO/S38
VCORE
23
53
P3.4/PM_SDCLK/S39
XIN
24
52
P3.3/PM_TA0.2
P3.2/PM_TACLK/PM_RTCCLK
P3.1/PM_TA2.1/BSL_RX
P3.0/PM_TA2.0/BSL_TX
P2.7/PM_TA1.1
P2.6/PM_TA1.0
P2.5/PM_UCA2CLK
P2.4/PM_UCA1CLK
P2.3/PM_UCA2TXD/PM_UCA2SIMO
P2.2/PM_UCA2RXD/PM_UCA2SOMI
P9.0/TACLK/RTCCLK
P8.7/TA2.1
P8.6/TA2.0
P2.1/PM_UCB0SIMO/PM_UCB0SDA/COM7
P2.0/PM_UCB0SOMI/PM_UCB0SCL/COM6
P1.7/PM_UCB0CLK/COM5
P1.6/PM_UCA0CLK/COM4
COM3
COM2
COM1
COM0
P8.5/TA1.1
P8.4/TA1.0
LCDCAP/R33
P1.5/PM_UCA1TXD/PM_UCA1SIMO/R23
AUXVCC3
25
51
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
P1.4/PM_UCA1RXD/PM_UCA1SOMI/LCDREF/R13
XOUT
PZ PACKAGE
NOTE: The secondary digital functions on Ports P1, P2, and P3 are fully mappable. The pin designation shows the default
mapping. See Table 6-7 for details.
NOTE: The pins VDSYS and DVSYS must be connected externally on board for proper device operation.
CAUTION: The LCDCAP/R33 pin must be connected to DVSS if not used.
Figure 4-1. 100-Pin PZ Package (Top View)
6
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-1. Pinout Differences Between MSP430F673xAIPZ and
MSP430F672xAIPZ (1)
PIN NAME
PIN NUMBER
(1)
MSP430F673xAIPZ
MSP430F672xAIPZ
1
SD0P0
SD0P0
2
SD0N0
SD0N0
3
SD1P0
SD1P0
4
SD1N0
SD1N0
5
SD2P0
NC
6
SD2N0
NC
7
VREF
VREF
53
P3.4/PM_SDCLK/S39
P3.4/PM_SDCLK/S39
54
P3.5/PM_SD0DIO/S38
P3.5/PM_SD0DIO/S38
55
P3.6/PM_SD1DIO/S37
P3.6/PM_SD1DIO/S37
56
P3.7/PM_SD2DIO/S36
P3.7/PM_NONE/S36
Signal names that differ between devices are indicated byitalic typeface.
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
7
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
P5.2/S13
P5.3/S12
P5.4/S11
P5.5/S10
P5.6/S9
P5.7/S8
P6.0/S7
P6.1/S6
P6.2/S5
P6.3/S4
P6.4/S3
P6.5/S2
P6.6/S1
P6.7/S0
TEST/SBWTCK
PJ.0/SMCLK/TDO
PJ.1/MCLK/TDI/TCLK
PJ.2/ADC10CLK/TMS
PJ.3/ACLK/TCK
RST/NMI/SBWTDIO
Figure 4-2 shows the pin assignments for the 80-pin PN package. See Table 4-2 for differences between
the MSP430F673xA and MSP430F672xA devices in this package.
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
SD0P0
1
60
DVSS
SD0N0
2
59
DVSYS
SD1P0
3
58
P5.1/S14
SD1N0
4
57
P5.0/S15
SD2P0
5
56
P4.7/S16
SD2N0
6
55
P4.6/S17
VREF
7
54
P4.5/S18
AVSS
8
53
P4.4/S19
AVCC
9
52
P4.3/S20
VASYS
10
51
P4.2/S21
P1.0/PM_TA0.0/VeREF-/A2
11
50
P4.1/S22
P1.1/PM_TA0.1/VeREF+/A1
12
49
P4.0/S23
P1.2/PM_UCA0RXD/PM_UCA0SOMI/A0
13
48
P3.7/PM_SD2DIO/S24
P1.3/PM_UCA0TXD/PM_UCA0SIMO/R03
14
47
P3.6/PM_SD1DIO/S25
AUXVCC2
15
46
P3.5/PM_SD0DIO/S26
AUXVCC1
16
45
P3.4/PM_SDCLK/S27
VDSYS
17
44
P3.3/PM_TA0.2/S28
DVCC
18
43
P3.2/PM_TACLK/PM_RTCCLK/S29
DVSS
19
42
P3.1/PM_TA2.1/S30/BSL_RX
20
41
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
P3.0/PM_TA2.0/S31/BSL_TX
P2.7/PM_TA1.1/S32
P2.6/PM_TA1.0/S33
P2.5/PM_UCA2CLK/S34
P2.4/PM_UCA1CLK/S35
P2.3/PM_UCA2TXD/PM_UCA2SIMO/S36
P2.2/PM_UCA2RXD/PM_UCA2SOMI/S37
P2.1/PM_UCB0SIMO/PM_UCB0SDA/COM7/S38
P2.0/PM_UCB0SOMI/PM_UCB0SCL/COM6/S39
P1.7/PM_UCB0CLK/COM5
P1.6/PM_UCA0CLK/COM4
COM3
COM2
COM1
COM0
LCDCAP/R33
P1.5/PM_UCA1TXD/PM_UCA1SIMO/R23
P1.4/PM_UCA1RXD/PM_UCA1SOMI/LCDREF/R13
AUXVCC3
XIN
XOUT
VCORE
PN PACKAGE
NOTE: The secondary digital functions on Ports P1, P2, and P3 are fully mappable. The pin designation shows the default
mapping. See Table 6-7 for details.
NOTE: The pins VDSYS and DVSYS must be connected externally on board for proper device operation.
CAUTION: The LCDCAP/R33 pin must be connected to DVSS if not used.
Figure 4-2. 80-Pin PN Package (Top View)
8
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-2. Pinout Differences Between MSP430F673xAIPN and
MSP430F672xAIPN (1)
PIN NAME
PIN NUMBER
(1)
MSP430F673xAIPN
MSP430F672xAIPN
1
SD0P0
SD0P0
2
SD0N0
SD0N0
3
SD1P0
SD1P0
4
SD1N0
SD1N0
5
SD2P0
NC
6
SD2N0
NC
7
VREF
VREF
45
P3.4/PM_SDCLK/S27
P3.4/PM_SDCLK/S27
46
P3.5/PM_SD0DIO/S26
P3.5/PM_SD0DIO/S26
47
P3.6/PM_SD1DIO/S25
P3.6/PM_SD1DIO/S25
48
P3.7/PM_SD2DIO/S24
P3.7/PM_NONE/S24
Signal names that differ between devices are indicated byitalic typeface.
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
9
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
4.2
www.ti.com
Pin Attributes
Table 4-3 lists the pin attributes for all device variants in the PZ package. For the PN package, see
Table 4-4.
Table 4-3. Pin Attributes, PZ Package
PIN NO.
SIGNAL NAME
(1) (2)
SIGNAL TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
SD0P0
I
Analog
AVCC
OFF
2
SD0N0
I
Analog
AVCC
OFF
3
SD1P0
I
Analog
AVCC
OFF
4
SD1N0
I
Analog
AVCC
OFF
5
SD2P0
I
Analog
AVCC
OFF
6
SD2N0
I
Analog
AVCC
OFF
7
VREF
I
Analog
-
OFF
8
AVSS
P
Power
-
N/A
9
AVCC
P
Power
-
N/A
10
VASYS
P
Power
-
N/A
I/O
LVCMOS
DVCC
OFF
12
13
14
15
P9.1
A5
I
Analog
AVCC
-
I/O
LVCMOS
DVCC
OFF
I
Analog
AVCC
-
I/O
LVCMOS
DVCC
OFF
I
Analog
AVCC
-
P1.0
I/O
LVCMOS
DVCC
OFF
PM_TA0.0
I/O
LVCMOS
DVCC
N/A
P9.2
A4
P9.3
A3
VeREF-
I
Power
-
A2
I
Analog
AVCC
-
P1.1
I/O
LVCMOS
DVCC
OFF
PM_TA0.1
I/O
LVCMOS
DVCC
-
VeREF+
I
Power
-
N/A
A1
I
Analog
AVCC
-
P1.2
16
I/O
LVCMOS
DVCC
OFF
PM_UCA0RXD
I
LVCMOS
DVCC
-
PM_UCA0SOMI
I/O
LVCMOS
DVCC
-
I
Analog
AVCC
-
P1.3
I/O
LVCMOS
DVCC
OFF
PM_UCA0TXD
O
LVCMOS
DVCC
-
PM_UCA0SIMO
I/O
LVCMOS
DVCC
-
R03
A0
17
10
BUFFER TYPE
1
11
(1)
(2)
(3)
(4)
(5)
(3)
I/O
Analog
AVCC
-
18
AUXVCC2
P
Power
-
N/A
19
AUXVCC1
P
Power
-
N/A
20
VDSYS
P
Power
-
N/A
For each multiplexed pin, the signal that is listed first in this table is the default after reset.
To determine the pin mux encodings for each pin, refer to the Port I/O Schematics section.
Signal Types: I = Input, O = Output, I/O = Input or Output.
Buffer Types: LVCMOS, Analog, or Power
Reset States:
OFF = High-impedance input with pullup or pulldown disabled (if available)
PD = High-impedance input with pulldown enabled
PU = High-impedance input with pullup enabled
DRIVE0 = Drive output low
DRIVE1 = Drive output high
N/A = Not applicable
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-3. Pin Attributes, PZ Package (continued)
PIN NO.
SIGNAL NAME
(1) (2)
SIGNAL TYPE
(3)
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
21
DVCC
P
Power
-
N/A
22
DVSS
P
Power
-
N/A
23
VCORE
P
Power
-
N/A
24
XIN
I
LVCMOS
DVCC
OFF
25
XOUT
O
LVCMOS
DVCC
OFF
26
AUXVCC3
P
Power
-
N/A
I/O
LVCMOS
DVCC
OFF
PM_UCA1RXD
I
LVCMOS
DVCC
-
PM_UCA1SOMI
I/O
LVCMOS
DVCC
-
I
Analog
AVCC
-
P1.4
27
LCDREF
28
29
30
31
R13
I/O
Analog
AVCC
-
P1.5
I/O
LVCMOS
DVCC
OFF
PM_UCA1TXD
O
LVCMOS
DVCC
-
PM_UCA1SIMO
I/O
LVCMOS
DVCC
-
R23
I/O
Analog
AVCC
-
LCDCAP
I/O
Analog
AVCC
OFF
R33
I/O
Analog
AVCC
-
P8.4
I/O
LVCMOS
DVCC
OFF
TA1.0
I/O
LVCMOS
DVCC
-
P8.5
I/O
LVCMOS
DVCC
OFF
TA1.1
I/O
LVCMOS
DVCC
-
32
COM0
O
LVCMOS
DVCC
OFF
33
COM1
O
LVCMOS
DVCC
OFF
34
COM2
O
LVCMOS
DVCC
OFF
35
COM3
O
LVCMOS
DVCC
OFF
P1.6
I/O
LVCMOS
DVCC
OFF
PM_UCA0CLK
I/O
LVCMOS
DVCC
-
COM4
O
LVCMOS
DVCC
-
P1.7
I/O
LVCMOS
DVCC
OFF
PM_UCB0CLK
I/O
LVCMOS
DVCC
-
COM5
O
LVCMOS
DVCC
-
P2.0
I/O
LVCMOS
DVCC
OFF
PM_UCB0SOMI
I/O
LVCMOS
DVCC
-
PM_UCB0SCL
I/O
LVCMOS
DVCC
-
COM6
O
LVCMOS
DVCC
-
P2.1
I/O
LVCMOS
DVCC
OFF
PM_UCB0SIMO
I/O
LVCMOS
DVCC
-
PM_UCB0SDA
I/O
LVCMOS
DVCC
-
COM7
O
LVCMOS
DVCC
-
P8.6
I/O
LVCMOS
DVCC
OFF
TA2.0
I/O
LVCMOS
DVCC
-
P8.7
I/O
LVCMOS
DVCC
OFF
TA2.1
I/O
LVCMOS
DVCC
-
P9.0
36
37
38
39
40
41
42
I/O
LVCMOS
DVCC
OFF
TACLK
I
LVCMOS
DVCC
-
RTCCLK
O
LVCMOS
DVCC
-
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
11
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-3. Pin Attributes, PZ Package (continued)
PIN NO.
SIGNAL NAME
(1) (2)
SIGNAL TYPE
P2.2
43
44
45
46
47
48
49
50
53
54
55
56
57
58
59
60
61
12
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
I/O
LVCMOS
DVCC
OFF
I
LVCMOS
DVCC
-
PM_UCA2SOMI
I/O
LVCMOS
DVCC
-
P2.3
I/O
LVCMOS
DVCC
OFF
PM_UCA2TXD
O
LVCMOS
DVCC
-
PM_UCA2SIMO
I/O
LVCMOS
DVCC
-
P2.4
I/O
LVCMOS
DVCC
OFF
PM_UCA1CLK
I/O
LVCMOS
DVCC
-
P2.5
I/O
LVCMOS
DVCC
OFF
PM_UCA2CLK
I/O
LVCMOS
DVCC
-
P2.6
I/O
LVCMOS
DVCC
OFF
PM_TA1.0
I/O
LVCMOS
DVCC
-
P2.7
I/O
LVCMOS
DVCC
OFF
PM_TA1.1
I/O
LVCMOS
DVCC
-
P3.0
I/O
LVCMOS
DVCC
OFF
PM_TA2.0
I/O
LVCMOS
DVCC
-
BSL_TX
O
LVCMOS
DVCC
-
P3.1
I/O
LVCMOS
DVCC
OFF
PM_TA2.1
I/O
LVCMOS
DVCC
-
I
LVCMOS
DVCC
-
P3.2
52
BUFFER TYPE
PM_UCA2RXD
BSL_RX
51
(3)
I/O
LVCMOS
DVCC
OFF
PM_TACLK
I
LVCMOS
DVCC
-
PM_RTCCLK
O
LVCMOS
DVCC
-
P3.3
I/O
LVCMOS
DVCC
OFF
PM_TA0.2
I/O
LVCMOS
DVCC
-
P3.4
I/O
LVCMOS
DVCC
OFF
PM_SDCLK
I/O
LVCMOS
DVCC
-
S39
O
LVCMOS
DVCC
-
P3.5
I/O
LVCMOS
DVCC
OFF
PM_SD0DIO
I/O
Analog
AVCC
-
S38
O
LVCMOS
DVCC
-
P3.6
I/O
LVCMOS
DVCC
OFF
PM_SD1DIO
I/O
Analog
AVCC
-
S37
O
LVCMOS
DVCC
-
P3.7
I/O
LVCMOS
DVCC
OFF
PM_SD2DIO
I/O
LVCMOS
DVCC
-
S36
O
LVCMOS
DVCC
-
P4.0
I/O
LVCMOS
DVCC
OFF
S35
O
LVCMOS
DVCC
-
P4.1
I/O
LVCMOS
DVCC
OFF
S34
O
LVCMOS
DVCC
-
P4.2
I/O
LVCMOS
DVCC
OFF
S33
O
LVCMOS
DVCC
-
P4.3
I/O
LVCMOS
DVCC
OFF
S32
O
LVCMOS
DVCC
-
P4.4
I/O
LVCMOS
DVCC
OFF
S31
O
LVCMOS
DVCC
-
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-3. Pin Attributes, PZ Package (continued)
PIN NO.
62
63
64
65
66
67
68
69
70
71
72
73
SIGNAL NAME
(1) (2)
SIGNAL TYPE
(3)
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
OFF
P4.5
I/O
LVCMOS
DVCC
S30
O
LVCMOS
DVCC
-
P4.6
I/O
LVCMOS
DVCC
OFF
S29
O
LVCMOS
DVCC
-
P4.7
I/O
LVCMOS
DVCC
OFF
S28
O
LVCMOS
DVCC
-
P5.0
I/O
LVCMOS
DVCC
OFF
S27
O
LVCMOS
DVCC
-
P5.1
I/O
LVCMOS
DVCC
OFF
S26
O
LVCMOS
DVCC
-
P5.2
I/O
LVCMOS
DVCC
OFF
S25
O
LVCMOS
DVCC
-
P5.3
I/O
LVCMOS
DVCC
OFF
S24
O
LVCMOS
DVCC
-
P5.4
I/O
LVCMOS
DVCC
OFF
S23
O
LVCMOS
DVCC
-
P5.5
I/O
LVCMOS
DVCC
OFF
S22
O
LVCMOS
DVCC
-
P5.6
I/O
LVCMOS
DVCC
OFF
S21
O
LVCMOS
DVCC
-
P5.7
I/O
LVCMOS
DVCC
OFF
S20
O
LVCMOS
DVCC
-
P6.0
I/O
LVCMOS
DVCC
OFF
S19
O
LVCMOS
DVCC
-
74
DVSYS
P
Power
-
N/A
75
DVSS
76
77
78
79
80
81
82
83
84
85
P
Power
-
N/A
I/O
LVCMOS
DVCC
OFF
S18
O
LVCMOS
DVCC
-
P6.2
I/O
LVCMOS
DVCC
OFF
S17
O
LVCMOS
DVCC
-
P6.3
I/O
LVCMOS
DVCC
OFF
S16
O
LVCMOS
DVCC
-
P6.4
I/O
LVCMOS
DVCC
OFF
S15
O
LVCMOS
DVCC
-
P6.5
I/O
LVCMOS
DVCC
OFF
S14
O
LVCMOS
DVCC
-
P6.6
I/O
LVCMOS
DVCC
OFF
S13
O
LVCMOS
DVCC
-
P6.7
I/O
LVCMOS
DVCC
OFF
S12
O
LVCMOS
DVCC
-
P7.0
I/O
LVCMOS
DVCC
OFF
S11
O
LVCMOS
DVCC
-
P7.1
I/O
LVCMOS
DVCC
OFF
S10
O
LVCMOS
DVCC
-
P7.2
I/O
LVCMOS
DVCC
OFF
S9
O
LVCMOS
DVCC
-
P6.1
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
13
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-3. Pin Attributes, PZ Package (continued)
PIN NO.
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SIGNAL NAME
(1) (2)
SIGNAL TYPE
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
OFF
P7.3
I/O
LVCMOS
DVCC
S8
O
LVCMOS
DVCC
-
P7.4
I/O
LVCMOS
DVCC
OFF
S7
O
LVCMOS
DVCC
-
P7.5
I/O
LVCMOS
DVCC
OFF
S6
O
LVCMOS
DVCC
-
P7.6
I/O
LVCMOS
DVCC
OFF
S5
O
LVCMOS
DVCC
-
P7.7
I/O
LVCMOS
DVCC
OFF
S4
O
LVCMOS
DVCC
-
P8.0
I/O
LVCMOS
DVCC
OFF
S3
O
LVCMOS
DVCC
-
P8.1
I/O
LVCMOS
DVCC
OFF
S2
O
LVCMOS
DVCC
-
P8.2
I/O
LVCMOS
DVCC
OFF
S1
O
LVCMOS
DVCC
-
P8.3
I/O
LVCMOS
DVCC
OFF
S0
O
LVCMOS
DVCC
-
TEST
I
LVCMOS
DVCC
OFF
SBWTCK
I
LVCMOS
DVCC
-
PJ.0
I/O
LVCMOS
DVCC
OFF
SMCLK
O
LVCMOS
DVCC
-
TDO
O
LVCMOS
DVCC
-
PJ.1
I/O
LVCMOS
DVCC
OFF
MCLK
O
LVCMOS
DVCC
-
TDI
I
LVCMOS
DVCC
-
TCLK
I
LVCMOS
DVCC
-
PJ.2
I/O
LVCMOS
DVCC
OFF
ADC10CLK
O
LVCMOS
DVCC
-
TMS
I
LVCMOS
DVCC
-
PJ.3
I/O
LVCMOS
DVCC
OFF
ACLK
O
LVCMOS
DVCC
-
TCK
I
LVCMOS
DVCC
-
RST
I
LVCMOS
DVCC
PU
NMI
I
LVCMOS
DVCC
-
I/O
LVCMOS
DVCC
-
SBWTDIO
14
(3)
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-4 lists the pin attributes for all device variants in the PN package. For the PZ package, see
Table 4-3.
Table 4-4. Pin Attributes, PN Package
PIN NO.
SIGNAL NAME
(2)
(1)
SIGNAL TYPE
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
1
SD0P0
I
Analog
AVCC
OFF
2
SD0N0
I
Analog
AVCC
OFF
3
SD1P0
I
Analog
AVCC
OFF
4
SD1N0
I
Analog
AVCC
OFF
5
SD2P0
I
Analog
AVCC
OFF
6
SD2N0
I
Analog
AVCC
OFF
7
VREF
I
Power
-
N/A
8
AVSS
P
Power
-
N/A
9
AVCC
P
Power
-
N/A
10
VASYS
11
12
P
Power
-
N/A
P1.0
I/O
LVCMOS
DVCC
OFF
PM_TA0.0
I/O
LVCMOS
DVCC
-
VeREF-
I
Power
-
A2
I
Analog
AVCC
-
P1.1
I/O
LVCMOS
DVCC
OFF
PM_TA0.1
I/O
LVCMOS
DVCC
-
VeREF+
I
Power
-
-
A1
I
Analog
AVCC
-
I/O
LVCMOS
DVCC
OFF
PM_UCA0RXD
I
LVCMOS
DVCC
-
PM_UCA0SOMI
I/O
LVCMOS
DVCC
-
I
Analog
AVCC
-
P1.3
I/O
LVCMOS
DVCC
OFF
PM_UCA0TXD
O
LVCMOS
DVCC
-
PM_UCA0SIMO
I/O
LVCMOS
DVCC
-
R03
P1.2
13
A0
14
(1)
(2)
(3)
(4)
(5)
(3)
I/O
Analog
AVCC
-
15
AUXVCC2
P
Power
-
N/A
16
AUXVCC1
P
Power
-
N/A
17
VDSYS
P
Power
-
N/A
18
DVCC
P
Power
-
N/A
19
DVSS
P
Power
-
N/A
20
VCORE
P
Power
-
N/A
21
XIN
I
LVCMOS
DVCC
OFF
22
XOUT
O
LVCMOS
DVCC
OFF
23
AUXVCC3
P
Power
-
N/A
For each multiplexed pin, the signal that is listed first in this table is the default after reset.
To determine the pin mux encodings for each pin, refer to the Port I/O Schematics section.
Signal Types: I = Input, O = Output, I/O = Input or Output.
Buffer Types: LVCMOS, Analog, or Power
Reset States:
OFF = High-impedance input with pullup or pulldown disabled (if available)
PD = High-impedance input with pulldown enabled
PU = High-impedance input with pullup enabled
DRIVE0 = Drive output low
DRIVE1 = Drive output high
N/A = Not applicable
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
15
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-4. Pin Attributes, PN Package (continued)
PIN NO.
SIGNAL NAME
(2)
P1.4
24
26
(3)
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
I/O
LVCMOS
DVCC
OFF
I
LVCMOS
DVCC
-
PM_UCA1SOMI
I/O
LVCMOS
DVCC
-
I
Analog
AVCC
R13
I/O
Analog
AVCC
-
P1.5
I/O
LVCMOS
DVCC
OFF
PM_UCA1TXD
O
LVCMOS
DVCC
-
PM_UCA1SIMO
I/O
LVCMOS
DVCC
-
R23
I/O
Analog
AVCC
-
LCDCAP
I/O
Analog
AVCC
OFF
R33
I/O
Analog
AVCC
OFF
27
COM0
O
LVCMOS
DVCC
OFF
28
COM1
O
LVCMOS
DVCC
OFF
29
COM2
O
LVCMOS
DVCC
OFF
30
COM3
O
LVCMOS
DVCC
OFF
P1.6
I/O
LVCMOS
DVCC
OFF
PM_UCA0CLK
I/O
LVCMOS
DVCC
-
COM4
O
LVCMOS
DVCC
-
P1.7
I/O
LVCMOS
DVCC
OFF
PM_UCB0CLK
I/O
LVCMOS
DVCC
-
COM5
O
LVCMOS
DVCC
-
P2.0
I/O
LVCMOS
DVCC
OFF
PM_UCB0SOMI
I/O
LVCMOS
DVCC
-
PM_UCB0SCL
I/O
LVCMOS
DVCC
-
COM6
O
LVCMOS
DVCC
-
S39
O
LVCMOS
DVCC
-
P2.1
I/O
LVCMOS
DVCC
OFF
PM_UCB0SIMO
I/O
LVCMOS
DVCC
-
PM_UCB0SDA
I/O
LVCMOS
DVCC
-
COM7
O
LVCMOS
DVCC
-
S38
O
LVCMOS
DVCC
-
P2.2
I/O
LVCMOS
DVCC
OFF
PM_UCA2RXD
I
LVCMOS
DVCC
-
PM_UCA2SOMI
I/O
LVCMOS
DVCC
-
S37
O
LVCMOS
DVCC
-
P2.3
I/O
LVCMOS
DVCC
OFF
PM_UCA2TXD
O
LVCMOS
DVCC
-
PM_UCA2SIMO
I/O
LVCMOS
DVCC
-
S36
O
LVCMOS
DVCC
-
P2.4
I/O
LVCMOS
DVCC
OFF
PM_UCA1CLK
I/O
LVCMOS
DVCC
-
S35
O
LVCMOS
DVCC
-
P2.5
I/O
LVCMOS
DVCC
OFF
PM_UCA2CLK
I/O
LVCMOS
DVCC
-
S34
O
LVCMOS
DVCC
-
31
32
33
34
35
36
37
38
16
SIGNAL TYPE
PM_UCA1RXD
LCDREF
25
(1)
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-4. Pin Attributes, PN Package (continued)
PIN NO.
39
40
41
42
SIGNAL NAME
(2)
(1)
SIGNAL TYPE
45
46
47
48
49
50
51
52
53
54
55
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
I/O
LVCMOS
DVCC
OFF
PM_TA1.0
I/O
LVCMOS
DVCC
-
S33
O
LVCMOS
DVCC
-
P2.7
I/O
LVCMOS
DVCC
OFF
PM_TA1.1
I/O
LVCMOS
DVCC
-
S32
O
LVCMOS
DVCC
-
P3.0
I/O
LVCMOS
DVCC
OFF
PM_TA2.0
I/O
LVCMOS
DVCC
-
S31
O
LVCMOS
DVCC
-
BSL_TX
O
LVCMOS
DVCC
-
P3.1
I/O
LVCMOS
DVCC
OFF
PM_TA2.1
I/O
LVCMOS
DVCC
-
S30
O
LVCMOS
DVCC
-
I
LVCMOS
DVCC
-
I/O
LVCMOS
DVCC
OFF
PM_TACLK
I
LVCMOS
DVCC
-
PM_RTCCLK
O
LVCMOS
DVCC
-
S29
O
LVCMOS
DVCC
-
P3.3
I/O
LVCMOS
DVCC
OFF
PM_TA0.2
I/O
LVCMOS
DVCC
-
S28
O
LVCMOS
DVCC
-
P3.4
I/O
LVCMOS
DVCC
OFF
PM_SDCLK
I/O
LVCMOS
DVCC
-
S27
O
LVCMOS
DVCC
-
P3.5
I/O
LVCMOS
DVCC
OFF
PM_SD0DIO
I/O
LVCMOS
DVCC
-
S26
O
LVCMOS
DVCC
-
P3.6
I/O
LVCMOS
DVCC
OFF
PM_SD1DIO
I/O
LVCMOS
DVCC
-
S25
O
LVCMOS
DVCC
-
P3.7
I/O
LVCMOS
DVCC
OFF
PM_SD2DIO
I/O
LVCMOS
DVCC
-
S24
O
LVCMOS
DVCC
-
P4.0
I/O
LVCMOS
DVCC
OFF
S23
O
LVCMOS
DVCC
-
P4.1
I/O
LVCMOS
DVCC
OFF
S22
O
LVCMOS
DVCC
-
P4.2
I/O
LVCMOS
DVCC
OFF
S21
O
LVCMOS
DVCC
-
P4.3
I/O
LVCMOS
DVCC
OFF
S20
O
LVCMOS
DVCC
-
P4.4
I/O
LVCMOS
DVCC
OFF
S19
O
LVCMOS
DVCC
-
P4.5
I/O
LVCMOS
DVCC
OFF
S18
O
LVCMOS
DVCC
-
P4.6
I/O
LVCMOS
DVCC
OFF
S17
O
LVCMOS
DVCC
-
P3.2
44
BUFFER TYPE
P2.6
BSL_RX
43
(3)
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
17
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-4. Pin Attributes, PN Package (continued)
PIN NO.
56
57
58
(2)
SIGNAL TYPE
(3)
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
OFF
P4.7
I/O
LVCMOS
DVCC
S16
O
LVCMOS
DVCC
-
P5.0
I/O
LVCMOS
DVCC
OFF
S15
O
LVCMOS
DVCC
-
P5.1
I/O
LVCMOS
DVCC
OFF
S14
O
LVCMOS
DVCC
-
59
DVSYS
P
Power
-
N/A
60
DVSS
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
18
SIGNAL NAME
(1)
P
Power
-
N/A
P5.2
I/O
LVCMOS
DVCC
OFF
S13
O
LVCMOS
DVCC
-
P5.3
I/O
LVCMOS
DVCC
OFF
S12
O
LVCMOS
DVCC
-
P5.4
I/O
LVCMOS
DVCC
OFF
S11
O
LVCMOS
DVCC
-
P5.5
I/O
LVCMOS
DVCC
OFF
S10
O
LVCMOS
DVCC
-
P5.6
I/O
LVCMOS
DVCC
OFF
S9
O
LVCMOS
DVCC
-
P5.7
I/O
LVCMOS
DVCC
OFF
S8
O
LVCMOS
DVCC
-
P6.0
I/O
LVCMOS
DVCC
OFF
S7
O
LVCMOS
DVCC
-
P6.1
I/O
LVCMOS
DVCC
OFF
S6
O
LVCMOS
DVCC
-
P6.2
I/O
LVCMOS
DVCC
OFF
S5
O
LVCMOS
DVCC
-
P6.3
I/O
LVCMOS
DVCC
OFF
S4
O
LVCMOS
DVCC
-
P6.4
I/O
LVCMOS
DVCC
OFF
S3
O
LVCMOS
DVCC
-
P6.5
I/O
LVCMOS
DVCC
OFF
S2
O
LVCMOS
DVCC
-
P6.6
I/O
LVCMOS
DVCC
OFF
S1
O
LVCMOS
DVCC
-
P6.7
I/O
LVCMOS
DVCC
OFF
S0
O
LVCMOS
DVCC
-
TEST
I
LVCMOS
DVCC
OFF
SBWTCK
I
LVCMOS
DVCC
-
PJ.0
I/O
LVCMOS
DVCC
OFF
SMCLK
O
LVCMOS
DVCC
-
TDO
O
LVCMOS
DVCC
-
PJ.1
I/O
LVCMOS
DVCC
OFF
MCLK
O
LVCMOS
DVCC
-
TDI
I
LVCMOS
DVCC
-
TCLK
I
LVCMOS
DVCC
-
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-4. Pin Attributes, PN Package (continued)
PIN NO.
78
79
80
SIGNAL NAME
(2)
(1)
SIGNAL TYPE
(3)
BUFFER TYPE
(4)
POWER SOURCE
RESET STATE AFTER
BOR (5)
PJ.2
I/O
LVCMOS
DVCC
OFF
ADC10CLK
O
LVCMOS
DVCC
-
TMS
I
LVCMOS
DVCC
-
PJ.3
I/O
LVCMOS
DVCC
OFF
ACLK
O
LVCMOS
DVCC
-
TCK
I
LVCMOS
DVCC
-
RST
I/O
LVCMOS
DVCC
PU
I
LVCMOS
DVCC
-
I/O
LVCMOS
DVCC
-
NMI
SBWTDIO
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
19
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
4.3
www.ti.com
Signal Descriptions
Table 4-5 describes the signals for all device variants in the PZ package. See Table 4-6 for signal
descriptions in the PN package.
Table 4-5. Signal Descriptions, PZ Package
FUNCTION
ADC10
BSL
Clock
Debug
PIN NO.
SIGNAL
TYPE
A0
16
I
Analog input A0 for 10-bit ADC
A1
15
I
Analog input A1 for 10-bit ADC
A2
14
I
Analog input A2 for 10-bit ADC
A3
13
I
Analog input A3 for 10-bit ADC
A4
12
I
Analog input A4 for 10-bit ADC
A5
11
I
Analog input A5 for 10-bit ADC
ADC10CLK
98
O
ADC10_A clock output
VeREF+
15
I
Positive terminal for the ADC reference voltage for an external applied
reference voltage
VeREF-
14
I
Negative terminal for the ADC reference voltage for an external applied
reference voltage
BSL_RX
50
I
Bootstrap loader: Data receive
BSL_TX
49
O
Bootstrap loader: Data transmit
ACLK
99
O
ACLK clock output
MCLK
97
O
MCLK clock output
PM_RTCCLK
51
O
Default mapping: RTCCLK clock output
RTCCLK
42
O
RTCCLK clock output
SMCLK
96
O
SMCLK clock output
XIN
24
I
Input terminal for crystal oscillator
XOUT
25
O
Output terminal for crystal oscillator
Spy-Bi-Wire input clock
SIGNAL NAME
SBWTCK
95
I
SBWTDIO
100
I/O
TCK
99
I
Test clock
TCLK
97
I
Test clock input
TDI
97
I
Test data input
TDO
96
O
Test data output
TEST
95
I
Test mode pin – select digital I/O on JTAG pins
TMS
98
I
Test mode select
P1.0
14
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.1
15
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.2
16
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.3
17
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.4
27
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.5
28
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.6
36
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P1.7
37
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
GPIO
20
DESCRIPTION
Terminal Configuration and Functions
Spy-Bi-Wire data input/output
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-5. Signal Descriptions, PZ Package (continued)
FUNCTION
GPIO
PIN NO.
SIGNAL
TYPE
P2.0
38
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.1
39
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.2
43
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.3
44
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.4
45
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.5
46
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.6
47
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P2.7
48
I/O
General-purpose digital I/O with port interrupt and mappable secondary
function
P3.0
49
I/O
General-purpose digital I/O with mappable secondary function
P3.1
50
I/O
General-purpose digital I/O with mappable secondary function
P3.2
51
I/O
General-purpose digital I/O with mappable secondary function
P3.3
52
I/O
General-purpose digital I/O with mappable secondary function
P3.4
53
I/O
General-purpose digital I/O with mappable secondary function
P3.5
54
I/O
General-purpose digital I/O with mappable secondary function
P3.6
55
I/O
General-purpose digital I/O with mappable secondary function
P3.7
56
I/O
General-purpose digital I/O with mappable secondary function
P4.0
57
I/O
General-purpose digital I/O
P4.1
58
I/O
General-purpose digital I/O
P4.2
59
I/O
General-purpose digital I/O
P4.3
60
I/O
General-purpose digital I/O
P4.4
61
I/O
General-purpose digital I/O
P4.5
62
I/O
General-purpose digital I/O
P4.6
63
I/O
General-purpose digital I/O
P4.7
64
I/O
General-purpose digital I/O
P5.0
65
I/O
General-purpose digital I/O
P5.1
66
I/O
General-purpose digital I/O
P5.2
67
I/O
General-purpose digital I/O
P5.3
68
I/O
General-purpose digital I/O
P5.4
69
I/O
General-purpose digital I/O
P5.5
70
I/O
General-purpose digital I/O
P5.6
71
I/O
General-purpose digital I/O
P5.7
72
I/O
General-purpose digital I/O
P6.0
73
I/O
General-purpose digital I/O
P6.1
76
I/O
General-purpose digital I/O
P6.2
77
I/O
General-purpose digital I/O
P6.3
78
I/O
General-purpose digital I/O
P6.4
79
I/O
General-purpose digital I/O
P6.5
80
I/O
General-purpose digital I/O
P6.6
81
I/O
General-purpose digital I/O
P6.7
82
I/O
General-purpose digital I/O
SIGNAL NAME
DESCRIPTION
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
21
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-5. Signal Descriptions, PZ Package (continued)
FUNCTION
GPIO
I2C
LCD
22
PIN NO.
SIGNAL
TYPE
P7.0
83
I/O
General-purpose digital I/O
P7.1
84
I/O
General-purpose digital I/O
P7.2
85
I/O
General-purpose digital I/O
P7.3
86
I/O
General-purpose digital I/O
P7.4
87
I/O
General-purpose digital I/O
P7.5
88
I/O
General-purpose digital I/O
P7.6
89
I/O
General-purpose digital I/O
P7.7
90
I/O
General-purpose digital I/O
P8.0
91
I/O
General-purpose digital I/O
P8.1
92
I/O
General-purpose digital I/O
P8.2
93
I/O
General-purpose digital I/O
P8.3
94
I/O
General-purpose digital I/O
P8.4
30
I/O
General-purpose digital I/O
P8.5
31
I/O
General-purpose digital I/O
P8.6
40
I/O
General-purpose digital I/O
P8.7
41
I/O
General-purpose digital I/O
P9.0
42
I/O
General-purpose digital I/O
P9.1
11
I/O
General-purpose digital I/O
P9.2
12
I/O
General-purpose digital I/O
P9.3
13
I/O
General-purpose digital I/O
PJ.0
96
I/O
General-purpose digital I/O
PJ.1
97
I/O
General-purpose digital I/O
PJ.2
98
I/O
General-purpose digital I/O
PJ.3
99
I/O
General-purpose digital I/O
PM_UCB0SCL
38
I/O
Default mapping: eUSCI_B0 I2C clock
PM_UCB0SDA
39
I/O
Default mapping: eUSCI_B0 I2C data
COM0
32
O
LCD common output COM0 for LCD backplane
COM1
33
O
LCD common output COM1 for LCD backplane
COM2
34
O
LCD common output COM2 for LCD backplane
COM3
35
O
LCD common output COM3 for LCD backplane
COM4
36
O
LCD common output COM4 for LCD backplane
COM5
37
O
LCD common output COM5 for LCD backplane
COM6
38
O
LCD common output COM6 for LCD backplane
COM7
39
O
LCD common output COM7 for LCD backplane
LCDCAP
29
I/O
LCD capacitor connection
CAUTION: This pin must be connected to DVSS if not used.
LCDREF
27
I
R03
17
I/O
Input/output port of lowest analog LCD voltage (V5)
R13
27
I/O
Input/output port of third most positive analog LCD voltage (V3 or V4)
R23
28
I/O
Input/output port of second most positive analog LCD voltage (V2)
R33
29
I/O
Input/output port of most positive analog LCD voltage (V1)
CAUTION: This pin must be connected to DVSS if not used.
SIGNAL NAME
Terminal Configuration and Functions
DESCRIPTION
External reference voltage input for regulated LCD voltage
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-5. Signal Descriptions, PZ Package (continued)
FUNCTION
LCD
PIN NO.
SIGNAL
TYPE
S0
94
O
LCD segment output S0
S1
93
O
LCD segment output S1
S2
92
O
LCD segment output S2
S3
91
O
LCD segment output S3
S4
90
O
LCD segment output S4
S5
89
O
LCD segment output S5
S6
88
O
LCD segment output S6
S7
87
O
LCD segment output S7
S8
86
O
LCD segment output S8
S9
85
O
LCD segment output S9
S10
84
O
LCD segment output S10
S11
83
O
LCD segment output S11
S12
82
O
LCD segment output S12
S13
81
O
LCD segment output S13
S14
80
O
LCD segment output S14
S15
79
O
LCD segment output S15
S16
78
O
LCD segment output S16
S17
77
O
LCD segment output S17
S18
76
O
LCD segment output S18
S19
73
O
LCD segment output S19
S20
72
O
LCD segment output S20
S21
71
O
LCD segment output S21
S22
70
O
LCD segment output S22
S23
69
O
LCD segment output S23
S24
68
O
LCD segment output S24
S25
67
O
LCD segment output S25
S26
66
O
LCD segment output S26
S27
65
O
LCD segment output S27
S28
64
O
LCD segment output S28
S29
63
O
LCD segment output S29
S30
62
O
LCD segment output S30
S31
61
O
LCD segment output S31
S32
60
O
LCD segment output S32
S33
59
O
LCD segment output S33
S34
58
O
LCD segment output S34
S35
57
O
LCD segment output S35
S36
56
O
LCD segment output S36
S37
55
O
LCD segment output S37
S38
54
O
LCD segment output S38
S39
53
O
LCD segment output S39
SIGNAL NAME
DESCRIPTION
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
23
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-5. Signal Descriptions, PZ Package (continued)
FUNCTION
Power
PIN NO.
SIGNAL
TYPE
AUXVCC1
19
P
Auxiliary power supply AUXVCC1
AUXVCC2
18
P
Auxiliary power supply AUXVCC2
AUXVCC3
26
P
Auxiliary power supply AUXVCC3 for back up subsystem
AVCC
9
P
Analog power supply
AVSS
8
P
Analog ground supply
DVCC
21
P
Digital power supply
DVSS
22
75
P
Digital ground supply
74
P
Digital power supply for I/Os
VASYS
10
P
Analog power supply selected among AVCC, AUXVCC1, AUXVCC2.
Connect recommended capacitor value of CVSYS (see Table 5-18).
VCORE (2)
23
P
Regulated core power supply (internal use only, no external current
loading)
VDSYS (1)
20
P
Digital power supply selected between DVCC, AUXVCC1, AUXVCC2.
Connect recommended capacitor value of CVSYS (see Table 5-18).
PM_SD0DIO
54
I/O
Default mapping: SD24_B converter 0 bit stream data input/output
PM_SD1DIO
55
I/O
Default mapping: SD24_B converter 1 bit stream data input/output
PM_SD2DIO
56
I/O
Default mapping: SD24_B converter 2 bit stream data input/output (not
available on F672xA devices)
PM_SDCLK
53
I/O
Default mapping: SD24_B bit stream clock input/output
SD0N0
2
I
SD24_B negative analog input for converter 0 (3)
SD0P0
1
I
SD24_B positive analog input for converter 0 (3)
SD1N0
4
I
SD24_B negative analog input for converter 1 (3)
SD1P0
3
I
SD24_B positive analog input for converter 1 (3)
SD2N0
6
I
SD24_B negative analog input for converter 2 (3) (not available on F672xA
devices)
SD2P0
5
I
SD24_B positive analog input for converter 2 (3) (not available on F672xA
devices)
SIGNAL NAME
DVSYS
SD24
SPI
System
(1)
(2)
(3)
(4)
24
(1)
DESCRIPTION
VREF
7
O
SD24_B external reference voltage
PM_UCA0CLK
36
I/O
Default mapping: eUSCI_A0 clock input/output
PM_UCA0SIMO
17
I/O
Default mapping: eUSCI_A0 SPI slave in/master out
PM_UCA0SOMI
16
I/O
Default mapping: eUSCI_A0 SPI slave out/master in
PM_UCA1CLK
45
I/O
Default mapping: eUSCI_A1 clock input/output
PM_UCA1SIMO
28
I/O
Default mapping: eUSCI_A1 SPI slave in/master out
PM_UCA1SOMI
27
I/O
Default mapping: eUSCI_A1 SPI slave out/master in
PM_UCA2CLK
46
I/O
Default mapping: eUSCI_A2 clock input/output
PM_UCA2SIMO
44
I/O
Default mapping: eUSCI_A2 SPI slave in/master out
PM_UCA2SOMI
43
I/O
Default mapping: eUSCI_A2 SPI slave out/master in
PM_UCB0CLK
37
I/O
Default mapping: eUSCI_B0 clock input/output
PM_UCB0SIMO
39
I/O
Default mapping: eUSCI_B0 SPI slave in/master out
PM_UCB0SOMI
38
I/O
Default mapping: eUSCI_B0 SPI slave out/master in
NMI
100
I
Nonmaskable interrupt input
RST
100
I
Reset input active low (4)
The pins VDSYS and DVSYS must be connected externally on board for proper device operation.
VCORE is for internal use only. No external current loading is possible. VCORE should only be connected to the recommended
capacitor value, CVCORE.
TI recommends shorting unused analog input pairs and connect them to analog ground.
When this pin is configured as reset, the internal pullup resistor is enabled by default.
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-5. Signal Descriptions, PZ Package (continued)
FUNCTION
Timer_A
UART
PIN NO.
SIGNAL
TYPE
PM_TA0.0
14
I/O
Default mapping: Timer TA0 CCR0 capture: CCI0A input, compare: Out0
output
PM_TA0.1
15
I/O
Default mapping: Timer TA0 CCR1 capture: CCI1A input, compare: Out1
output
PM_TA0.2
52
I/O
Default mapping: Timer TA0 capture CCR2: CCI2A input, compare: Out2
output
PM_TA1.0
47
I/O
Default mapping: Timer TA1 capture CCR0: CCI0A input, compare: Out0
output
PM_TA1.1
48
I/O
Default mapping: Timer TA1 capture CCR1: CCI1A input, compare: Out1
output
PM_TA2.0
49
I/O
Default mapping: Timer TA2 capture CCR0: CCI0A input, compare: Out0
output
PM_TA2.1
50
I/O
Default mapping: Timer TA2 capture CCR1: CCI1A input, compare: Out1
output
PM_TACLK
51
I
TA1.0
30
I/O
Timer TA1 CCR0 capture: CCI0A input, compare: Out0 output
TA1.1
31
I/O
Timer TA1 CCR1 capture: CCI1A input, compare: Out1 output
TA2.0
40
I/O
Timer TA2 CCR0 capture: CCI0A input, compare: Out0 output
TA2.1
41
I/O
Timer TA2 CCR1 capture: CCI1A input, compare: Out1 output
TACLK
42
I
Timer clock input TACLK for TA0, TA1, TA2, TA3
PM_UCA0RXD
16
I
Default mapping: eUSCI_A0 UART receive data
PM_UCA0TXD
17
O
Default mapping: eUSCI_A0 UART transmit data
PM_UCA1RXD
27
I
Default mapping: eUSCI_A1 UART receive data
PM_UCA1TXD
28
O
Default mapping: eUSCI_A1 UART transmit data
PM_UCA2RXD
43
I
Default mapping: eUSCI_A2 UART receive data
PM_UCA2TXD
44
O
Default mapping: eUSCI_A2 UART transmit data
SIGNAL NAME
DESCRIPTION
Default mapping: Timer clock input TACLK for TA0, TA1, TA2, TA3
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
25
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-6 describes the signals for all device variants in the PN package. See Table 4-5 for signal
descriptions in the PZ package.
Table 4-6. Signal Descriptions, PN Package
FUNCTION
ADC10
BSL
Clock
Debug
PIN NO.
SIGNAL
TYPE (1)
A0
13
I
Analog input A0 for 10-bit ADC
A1
12
I
Analog input A1 for 10-bit ADC
A2
11
I
Analog input A2 for 10-bit ADC
ADC10CLK
78
O
ADC10_A clock output
VeREF+
12
I
Positive terminal for the ADC reference voltage for an external
applied reference voltage
VeREF-
11
I
Negative terminal for the ADC's reference voltage for an external
applied reference voltage
BSL_RX
42
I
Bootstrap loader: Data receive
BSL_TX
41
O
Bootstrap loader: Data transmit
ACLK
79
O
ACLK clock output
MCLK
77
O
MCLK clock output
PM_RTCCLK
43
O
Default mapping: RTCCLK clock output
SMCLK
76
O
SMCLK clock output
XIN
21
I
Input terminal for crystal oscillator
XOUT
22
O
Output terminal for crystal oscillator
SBWTCK
75
I
Spy-Bi-Wire input clock
SBWTDIO
80
I/O
TCK
79
I
Test clock
TCLK
77
I
Test clock input
TDI
77
I
Test data input
TDO
76
O
Test data output
TEST
75
I
Test mode pin – select digital I/O on JTAG pins
TMS
78
I
Test mode select
P1.0
11
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.1
12
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.2
13
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.3
14
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.4
24
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.5
25
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.6
31
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P1.7
32
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.0
33
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.1
34
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.2
35
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.3
36
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
SIGNAL NAME
GPIO
(1)
26
DESCRIPTION
Spy-Bi-Wire data input/output
I = input, O = output
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-6. Signal Descriptions, PN Package (continued)
FUNCTION
GPIO
I2C
PIN NO.
SIGNAL
TYPE (1)
P2.4
37
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.5
38
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.6
39
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P2.7
40
I/O
General-purpose digital I/O with port interrupt and mappable
secondary function
P3.0
41
I/O
General-purpose digital I/O with mappable secondary function
P3.1
42
I/O
General-purpose digital I/O with mappable secondary function
P3.2
43
I/O
General-purpose digital I/O with mappable secondary function
P3.3
44
I/O
General-purpose digital I/O with mappable secondary function
P3.4
45
I/O
General-purpose digital I/O with mappable secondary function
P3.5
46
I/O
General-purpose digital I/O with mappable secondary function
P3.6
47
I/O
General-purpose digital I/O with mappable secondary function
P3.7
48
I/O
General-purpose digital I/O with mappable secondary function
P4.0
49
I/O
General-purpose digital I/O
P4.1
50
I/O
General-purpose digital I/O
P4.2
51
I/O
General-purpose digital I/O
P4.3
52
I/O
General-purpose digital I/O
P4.4
53
I/O
General-purpose digital I/O
P4.5
54
I/O
General-purpose digital I/O
P4.6
55
I/O
General-purpose digital I/O
P4.7
56
I/O
General-purpose digital I/O
P5.0
57
I/O
General-purpose digital I/O
P5.1
58
I/O
General-purpose digital I/O
P5.2
61
I/O
General-purpose digital I/O
P5.3
62
I/O
General-purpose digital I/O
P5.4
63
I/O
General-purpose digital I/O
P5.5
64
I/O
General-purpose digital I/O
P5.6
65
I/O
General-purpose digital I/O
P5.7
66
I/O
General-purpose digital I/O
P6.0
67
I/O
General-purpose digital I/O
P6.1
68
I/O
General-purpose digital I/O
P6.2
69
I/O
General-purpose digital I/O
P6.3
70
I/O
General-purpose digital I/O
P6.4
71
I/O
General-purpose digital I/O
P6.5
72
I/O
General-purpose digital I/O
P6.6
73
I/O
General-purpose digital I/O
P6.7
74
I/O
General-purpose digital I/O
PJ.0
76
I/O
General-purpose digital I/O
PJ.1
77
I/O
General-purpose digital I/O
PJ.2
78
I/O
General-purpose digital I/O
PJ.3
79
I/O
General-purpose digital I/O
PM_UCB0SCL
33
I/O
Default mapping: eUSCI_B0 I2C clock
PM_UCB0SDA
34
I/O
Default mapping: eUSCI_B0 I2C data
SIGNAL NAME
DESCRIPTION
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
27
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-6. Signal Descriptions, PN Package (continued)
FUNCTION
LCD
28
PIN NO.
SIGNAL
TYPE (1)
COM0
27
O
LCD common output COM0 for LCD backplane
COM1
28
O
LCD common output COM1 for LCD backplane
COM2
29
O
LCD common output COM2 for LCD backplane
COM3
30
O
LCD common output COM3 for LCD backplane
COM4
31
O
LCD common output COM4 for LCD backplane
COM5
32
O
LCD common output COM5 for LCD backplane
COM6
33
O
LCD common output COM6 for LCD backplane
COM7
34
O
LCD common output COM7 for LCD backplane
LCDCAP
26
I/O
LCD capacitor connection
CAUTION: This pin must be connected to DVSS if not used.
LCDREF
24
I
R03
14
I/O
Input/output port of lowest analog LCD voltage (V5)
R13
24
I/O
Input/output port of third most positive analog LCD voltage (V3 or
V4)
R23
25
I/O
Input/output port of second most positive analog LCD voltage (V2)
R33
26
I/O
Input/output port of most positive analog LCD voltage (V1)
CAUTION: This pin must be connected to DVSS if not used.
S0
74
O
LCD segment output S0
S1
73
O
LCD segment output S1
S2
72
O
LCD segment output S2
S3
71
O
LCD segment output S3
S4
70
O
LCD segment output S4
S5
69
O
LCD segment output S5
S6
68
O
LCD segment output S6
S7
67
O
LCD segment output S7
S8
66
O
LCD segment output S8
S9
65
O
LCD segment output S9
S10
64
O
LCD segment output S10
S11
63
O
LCD segment output S11
S12
62
O
LCD segment output S12
S13
61
O
LCD segment output S13
S14
58
O
LCD segment output S14
S15
57
O
LCD segment output S15
S16
56
O
LCD segment output S16
S17
55
O
LCD segment output S17
S18
54
O
LCD segment output S18
S19
53
O
LCD segment output S19
S20
52
O
LCD segment output S20
S21
51
O
LCD segment output S21
S22
50
O
LCD segment output S22
S23
49
O
LCD segment output S23
S24
48
O
LCD segment output S24
S25
47
O
LCD segment output S25
S26
46
O
LCD segment output S26
SIGNAL NAME
Terminal Configuration and Functions
DESCRIPTION
External reference voltage input for regulated LCD voltage
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 4-6. Signal Descriptions, PN Package (continued)
FUNCTION
LCD
Power
SD24
(2)
(3)
(4)
PIN NO.
SIGNAL
TYPE (1)
S27
45
O
LCD segment output S27
S28
44
O
LCD segment output S28
S29
43
O
LCD segment output S29
S30
42
O
LCD segment output S30
S31
41
O
LCD segment output S31
S32
40
O
LCD segment output S32
S33
39
O
LCD segment output S33
S34
38
O
LCD segment output S34
S35
37
O
LCD segment output S35
S36
36
O
LCD segment output S36
S37
35
O
LCD segment output S37
S38
34
O
LCD segment output S38
S39
33
O
LCD segment output S39
AUXVCC1
16
P
Auxiliary power supply AUXVCC1
AUXVCC2
15
P
Auxiliary power supply AUXVCC2
AUXVCC3
23
P
Auxiliary power supply AUXVCC3 for backup subsystem
AVCC
9
P
Analog power supply
AVSS
8
P
Analog ground supply
DVCC
18
P
Digital power supply
DVSS
19
P
Digital ground supply
DVSS
60
P
Digital ground supply
DVSYS (2)
59
P
Digital power supply for I/Os
VASYS
10
P
Analog power supply selected between AVCC, AUXVCC1,
AUXVCC2. Connect recommended capacitor value of CVSYS (see
Table 5-18).
VCORE (3)
20
P
Regulated core power supply (internal use only, no external current
loading)
VDSYS (2)
17
P
Digital power supply selected between DVCC, AUXVCC1,
AUXVCC2. Connect recommended capacitor value of CVSYS (see
Table 5-18).
PM_SD0DIO
46
I/O
Default mapping: SD24_B converter 0 bit stream data input/output
PM_SD1DIO
47
I/O
Default mapping: SD24_B converter 1 bit stream data input/output
PM_SD2DIO
48
I/O
Default mapping: SD24_B converter 2 bit stream data input/output
(not available on F672xA devices)
PM_SDCLK
45
I/O
Default mapping: SD24_B bit stream clock input/output
SD0N0
2
I
SD24_B negative analog input for converter 0 (4)
SD0P0
1
I
SD24_B positive analog input for converter 0 (4)
SD1N0
4
I
SD24_B negative analog input for converter 1 (4)
SD1P0
3
I
SD24_B positive analog input for converter 1 (4)
SD2N0
6
I
SD24_B negative analog input for converter 2 (4) (not available on
F672xA devices)
SD2P0
5
I
SD24_B positive analog input for converter 2 (4) (not available on
F672xA devices)
VREF
7
I
SD24_B external reference voltage
SIGNAL NAME
DESCRIPTION
The pins VDSYS and DVSYS must be connected externally on board for proper device operation.
VCORE is for internal use only. No external current loading is possible. VCORE should only be connected to the recommended
capacitor value, CVCORE.
TI recommends shorting unused analog input pairs and connect them to analog ground.
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
29
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 4-6. Signal Descriptions, PN Package (continued)
FUNCTION
SPI
System
Timer_A
UART
(5)
30
PIN NO.
SIGNAL
TYPE (1)
PM_UCA0CLK
31
I/O
Default mapping: eUSCI_A0 clock input/output
PM_UCA0SIMO
14
I/O
Default mapping: eUSCI_A0 SPI slave in/master out
PM_UCA0SOMI
13
I/O
Default mapping: eUSCI_A0 SPI slave out/master in
PM_UCA1CLK
37
I/O
Default mapping: eUSCI_A1 clock input/output
PM_UCA1SIMO
25
I/O
Default mapping: eUSCI_A1 SPI slave in/master out
PM_UCA1SOMI
24
I/O
Default mapping: eUSCI_A1 SPI slave out/master in
PM_UCA2CLK
38
I/O
Default mapping: eUSCI_A2 clock input/output
PM_UCA2SIMO
36
I/O
Default mapping: eUSCI_A2 SPI slave in/master out
PM_UCA2SOMI
35
I/O
Default mapping: eUSCI_A2 SPI slave out/master in
PM_UCB0CLK
32
I/O
Default mapping: eUSCI_B0 clock input/output
PM_UCB0SIMO
34
I/O
Default mapping: eUSCI_B0 SPI slave in/master out
PM_UCB0SOMI
33
I/O
Default mapping: eUSCI_B0 SPI slave out/master in
NMI
80
I
RST
80
I/O
Reset input active low (5)
PM_TA0.0
11
I/O
Default mapping: Timer TA0 CCR0 capture: CCI0A input, compare:
Out0 output
PM_TA0.1
12
I/O
Default mapping: Timer TA0 CCR1 capture: CCI1A input, compare:
Out1 output
PM_TA0.2
44
I/O
Default mapping: Timer TA0 capture CCR2: CCI2A input, compare:
Out2 output
PM_TA1.0
39
I/O
Default mapping: Timer TA1 capture CCR0: CCI0A input, compare:
Out0 output
PM_TA1.1
40
I/O
Default mapping: Timer TA1 capture CCR1: CCI1A input, compare:
Out1 output
PM_TA2.0
41
I/O
Default mapping: Timer TA2 capture CCR0: CCI0A input, compare:
Out0 output
PM_TA2.1
42
I/O
Default mapping: Timer TA2 capture CCR1: CCI1A input, compare:
Out1 output
PM_TACLK
43
I
Default mapping: Timer clock input TACLK for TA0, TA1, TA2, TA3
PM_UCA0RXD
13
I
Default mapping: eUSCI_A0 UART receive data
PM_UCA0TXD
14
O
Default mapping: eUSCI_A0 UART transmit data
PM_UCA1RXD
24
I
Default mapping: eUSCI_A1 UART receive data
PM_UCA1TXD
25
O
Default mapping: eUSCI_A1 UART transmit data
PM_UCA2RXD
35
I
Default mapping: eUSCI_A2 UART receive data
PM_UCA2TXD
36
O
Default mapping: eUSCI_A2 UART transmit data
SIGNAL NAME
DESCRIPTION
Nonmaskable interrupt input
When this pin is configured as reset, the internal pullup resistor is enabled by default.
Terminal Configuration and Functions
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
4.4
SLASE46 – FEBRUARY 2015
Pin Multiplexing
Pin multiplexing for these devices is controlled by both register settings and operating modes (for
example, if the device is in test mode). For details of the settings for each pin and schematics of the
multiplexed ports, see Section 6.11.25.
4.5
Connection of Unused Pins
The correct termination of all unused pins is listed in Table 4-7.
Table 4-7. Connection of Unused Pins (1)
PIN
POTENTIAL
COMMENT
AVCC
DVCC
AVSS
DVSS
Px.y
Open
Switched to port function, output direction (PxDIR.n = 1). Px.y represents port x and bit y
of port x (for example, P1.0, P1.1, P2.2, PJ.0, PJ.1)
XIN
DVSS
For dedicated XIN pins only. XIN pins with shared GPIO functions should be
programmed to GPIO and follow Px.y recommendations.
XOUT
Open
For dedicated XOUT pins only. XOUT pins with shared GPIO functions should be
programmed to GPIO and follow Px.y recommendations.
LCDCAP
DVSS
RST/NMI
DVCC or VCC
47-kΩ pullup or internal pullup selected with 10-nF (2.2 nF) pulldown (2)
PJ.0/TDO
PJ.1/TDI
PJ.2/TMS
PJ.3/TCK
Open
The JTAG pins are shared with general-purpose I/O function (PJ.x). If not being used,
these should be switched to port function, output direction (PJDIR.n = 1). When used as
JTAG pins, these pins should remain open.
TEST
Open
This pin always has an internal pulldown enabled.
(1)
(2)
Any unused pin with a secondary function that is shared with a general-purpose I/O should follow the Px.y unused pin connection
guidelines.
The pulldown capacitor should not exceed 2.2 nF when using devices with Spy-Bi-Wire interface in Spy-Bi-Wire mode or in 4-wire JTAG
mode with TI tools such as FET interfaces or GANG programmers.
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
31
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
5 Specifications
Absolute Maximum Ratings (1)
5.1
over operating free-air temperature range (unless otherwise noted)
Voltage applied at DVCC to DVSS
Voltage applied to any pin (excluding VCORE)
(2)
MIN
MAX
–0.3
4.1
–0.3
VCC + 0.3
Diode current at any device pin
(1)
(2)
(3)
–55
V
V
±2
mA
95
°C
150
°C
Maximum junction temperature, TJ
Storage temperature, Tstg (3)
UNIT
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. VCORE is for internal device usage only. No external DC loading or voltage should be applied.
Higher temperature may be applied during board soldering according to the current JEDEC J-STD-020 specification with peak reflow
temperatures not higher than classified on the device label on the shipping boxes or reels.
5.2
ESD Ratings
VALUE
V(ESD)
(1)
(2)
5.3
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±1000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±250
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as
±1000 V may actually have higher performance.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Pins listed as ±250 V
may actually have higher performance.
Recommended Operating Conditions
Typical values are specified at VCC = 3.3 V and TA = 25°C (unless otherwise noted)
MIN
NOM
MAX
PMMCOREVx = 0
1.8
3.6
PMMCOREVx = 0, 1
2.0
3.6
PMMCOREVx = 0, 1, 2
2.2
3.6
PMMCOREVx = 0, 1, 2, 3
2.4
VCC
Supply voltage during program execution and flash
programming. V(AVCC) = V(DVCC) = VCC (1) (2)
VSS
Supply voltage V(AVSS) = V(DVSS) = VSS
TA
Operating free-air temperature
I version
–40
85
TJ
Operating junction temperature
I version
–40
85
CVCORE
Recommended capacitor at VCORE (3)
CDVCC /
CVCORE
Capacitor ratio of DVCC to VCORE
(1)
(2)
(3)
32
UNIT
V
3.6
0
470
V
°C
°C
nF
10
TI recommends powering AVCC and DVCC from the same source. A maximum difference of 0.3 V between V(AVCC) and V(DVCC) can
be tolerated during power up and operation.
The minimum supply voltage is defined by the supervisor SVS levels when it is enabled. See the Table 5-14 threshold parameters for
the exact values and further details.
A capacitor tolerance of ±20% or better is required.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Recommended Operating Conditions (continued)
Typical values are specified at VCC = 3.3 V and TA = 25°C (unless otherwise noted)
MIN
fSYSTEM
Processor frequency (maximum MCLK frequency) (4)
(see Figure 5-1)
(5)
NOM
MAX
PMMCOREVx = 0,
1.8 V ≤ VCC ≤ 3.6 V
(default condition)
0
8.0
PMMCOREVx = 1,
2.0 V ≤ VCC ≤ 3.6 V
0
12.0
PMMCOREVx = 2,
2.2 V ≤ VCC ≤ 3.6 V
0
20.0
PMMCOREVx = 3,
2.4 V ≤ VCC ≤ 3.6 V
0
25.0
UNIT
MHz
ILOAD,
DVCCD
Maximum load current that can be drawn from DVCC for core and IO
(ILOAD = ICORE + IIO)
20
mA
ILOAD,
AUX1D
Maximum load current that can be drawn from AUXVCC1 for core and IO
(ILOAD = ICORE + IIO)
20
mA
ILOAD,
AUX2D
Maximum load current that can be drawn from AUXVCC2 for core and IO
(ILOAD = ICORE + IIO)
20
mA
ILOAD,
AVCCA
Maximum load current that can be drawn from AVCC for analog modules
(ILOAD = IModules)
10
mA
ILOAD,
AUX1A
Maximum load current that can be drawn from AUXVCC1 for analog modules
(ILOAD = IModules)
5
mA
ILOAD,
AUX2A
Maximum load current that can be drawn from AUXVCC2 for analog modules
(ILOAD = IModules)
5
mA
(4)
(5)
The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse width of the
specified maximum frequency.
Modules may have a different maximum input clock specification. Refer to the specification of the respective module in this data sheet.
25
System Frequency - MHz
3
20
2
2, 3
1
1, 2
1, 2, 3
0, 1
0, 1, 2
0, 1, 2, 3
12
8
0
0
1.8
2.0
2.2
2.4
3.6
Supply Voltage - V
The numbers within the fields denote the supported PMMCOREVx settings.
Figure 5-1. Maximum System Frequency
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
33
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.4
www.ti.com
Active Mode Supply Current Into VCC Excluding External Current
over recommended operating free-air temperature (unless otherwise noted) (1)
(2) (3)
FREQUENCY (fDCO = fMCLK = fSMCLK)
PARAMETER
EXECUTION
MEMORY
VCC
PMMCOREVx
1 MHz
TYP
IAM,
IAM,
(1)
(2)
(3)
(4)
(5)
34
Flash
RAM
(4)
(5)
Flash
RAM
3.0 V
3.0 V
8 MHz
MAX
0.36
TYP
2.10
12 MHz
MAX
TYP
20 MHz
MAX
TYP
0
0.32
1
0.36
2.39
3.54
2
0.39
2.65
3.94
6.54
3
0.42
4.20
6.96
0
0.20
1
0.22
1.30
1.90
2
0.24
1.45
2.15
3.55
3
0.26
1.55
2.30
3.80
1.10
TYP
UNIT
MAX
2.30
2.82
0.22
25 MHz
MAX
3.90
mA
7.23
8.65
9.54
1.22
2.10
mA
4.0
4.70
5.30
All inputs are tied to 0 or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external load
capacitance are chosen to closely match the required 12.5 pF.
Characterized with program executing typical data processing.
fACLK = 32786 Hz, fDCO = fMCLK = fSMCLK at specified frequency.
XTS = CPUOFF = SCG0 = SCG1 = OSCOFF = SMCLKOFF = 0.
Active mode supply current when program executes in flash at a nominal supply voltage of 3 V.
Active mode supply current when program executes in RAM at a nominal supply voltage of 3 V.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
5.5
SLASE46 – FEBRUARY 2015
Low-Power Mode Supply Currents (Into VCC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
(2)
TEMPERATURE (TA)
PARAMETER
VCC
PMMCOREVx
–40°C
TYP
ILPM0,1MHz
Low-power mode 0 (3)
(4)
ILPM2
Low-power mode 2 (5)
(4)
ILPM3,XT1LF
Low-power mode 3, crystal
mode (6) (4)
ILPM3,XT1LF
ILPM3,VLO
ILPM4
Low-power mode 3, crystal
mode (6) (4)
Low-power mode 3,
VLO mode (7) (4)
(4)
ILPM4.5
Low-power mode 3.5, RTC
active on AUXVCC3 (9)
Low-power mode 4.5
(10)
60°C
TYP
MAX
TYP
85°C
MAX
TYP
UNIT
MAX
0
75
78
87
81
84
96
3.0 V
3
85
89
99
93
98
110
2.2 V
0
5.9
6.2
9
6.9
9.4
17
3.0 V
3
6.9
7.4
10
8.4
11
19
0
1.4
1.7
2.5
4.9
1
1.5
1.9
2.7
5.2
2
1.7
2.0
2.9
5.5
0
2.2
2.5
3.3
5.5
1
2.3
2.7
3.5
5.8
2
2.5
2.9
3.7
6.1
3
2.5
2.9
3.5
3.7
6.1
14.0
0
1.4
1.7
2.2
2.4
4.5
11.5
1
1.5
1.8
2.5
4.7
2
1.6
1.9
2.7
4.9
3
1.6
1.9
2.4
2.7
5.0
12.7
0
1.3
1.6
2.0
2.3
4.4
11.1
1
1.4
1.6
2.4
4.5
2
1.4
1.7
2.5
4.8
2.2 V
3.0 V
3.0 V
3
ILPM3.5
MAX
2.2 V
3.0 V
Low-power mode 4 (8)
25°C
1.4
1.7
2.2V
0.65
0.80
3.0V
1.16
1.24
3.0V
0.70
0.78
3.1
2.2
µA
µA
µA
12.7
µA
µA
µA
2.5
4.8
0.90
1.30
12.2
2.05
1.43
1.87
2.71
1.05
0.90
1.20
1.85
µA
µA
(1)
(2)
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external load
capacitance are chosen to closely match the required 12.5 pF.
(3) Current for watchdog timer clocked by SMCLK included. ACLK = low frequency crystal operation (XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 0, OSCOFF = 0 (LPM0), fACLK = 32768 Hz, fMCLK = 0 MHz, fSMCLK = fDCO = 1 MHz
(4) Current for brownout, high side supervisor (SVSH) normal mode included. Low side supervisor and monitors disabled (SVSL, SVML).
High side monitor disabled (SVMH). RAM retention enabled.
(5) Current for watchdog timer clocked by ACLK and RTC clocked by XT1 included. ACLK = low frequency crystal operation (XTS = 0,
XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 0, SCG1 = 1, OSCOFF = 0 (LPM2), fACLK = 32768 Hz, fMCLK = 0 MHz, fSMCLK = fDCO = 0 MHz, DCO setting
= 1 MHz operation, DCO bias generator enabled.
(6) Current for watchdog timer clocked by ACLK and RTC clocked by XT1 included. ACLK = low frequency crystal operation (XTS = 0,
XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3), fACLK = 32768 Hz, fMCLK = fSMCLK = fDCO = 0 MHz
(7) Current for watchdog timer clocked by ACLK included. RTC is disabled (RTCHOLD=1). ACLK = VLO.
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3), fACLK = fVLO, fMCLK = fSMCLK = fDCO = 0 MHz
(8) CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 1 (LPM4), fDCO = fACLK = fMCLK = fSMCLK = 0 MHz
(9) fDCO = fMCLK = fSMCLK = 0 MHz, fACLK = 32768 Hz, PMMREGOFF = 1, RTC active on AUXVCC3 supply
(10) fDCO = fMCLK = fSMCLK = 0 MHz, fACLK = 0 Hz, PMMREGOFF = 1
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
35
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.6
www.ti.com
Low-Power Mode With LCD Supply Currents (Into VCC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
(2)
Temperature (TA)
PARAMETER
VCC
PMMCOREVx
–40°C
TYP
ILPM3
LCD,
int. bias
Low-power mode 3
(LPM3) current, LCD 4mux mode, internal
biasing, charge pump
disabled (3) (4)
ILPM3
LCD,
int. bias
Low-power mode 3
(LPM3) current, LCD 4mux mode, internal
biasing, charge pump
disabled (3) (4)
2.2 V
3.0 V
2.2 V
ILPM3
LCD,CP
(1)
(2)
(3)
(4)
(5)
36
Low-power mode 3
(LPM3) current, LCD 4mux mode, internal
biasing, charge pump
enabled (3) (5)
3.0 V
MAX
25°C
TYP
0
2.4
2.9
1
2.5
3.1
2
2.6
3.3
0
2.8
3.2
1
2.9
2
3.1
3
3.1
3.6
60°C
MAX
TYP
85°C
TYP
UNIT
MAX
3.8
5.8
4.0
6.0
3.9
4.2
6.3
13.4
3.9
4.1
6.4
13.3
3.4
4.3
6.7
3.6
4.5
7.0
4.5
7.0
0
3.8
1
3.9
2
4.0
0
4.0
1
4.1
2
4.2
3
4.2
3.6
MAX
4.5
12.2
µA
µA
14.7
µA
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal MS1V-T1K crystal with a load capacitance of 12.5 pF. The internal and external load
capacitance are chosen to closely match the required 12.5 pF.
Current for watchdog timer clocked by ACLK and RTC clocked by XT1 included. ACLK = low-frequency crystal operation (XTS = 0,
XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3), fACLK = 32768 Hz, fMCLK = fSMCLK = fDCO = 0 MHz
Current for brownout and high-side supervisor (SVSH) normal mode included. Low-side supervisor and monitors disabled (SVSL, SVML).
High-side monitor disabled (SVMH). RAM retention enabled.
LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 0 (charge pump
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (fLCD = 32768 Hz / 32 / 4 = 256 Hz)
Even segments S0, S2, ... = 0 and odd segments S1, S3, ... = 1. No LCD panel load.
LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 1 (charge pump
enabled), VLCDx = 1000 (VLCD = 3V,typ.), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (fLCD = 32768 Hz / 32 / 4 = 256 Hz)
Even segments S0, S2, ... = 0 and odd segments S1, S3, ... = 1. No LCD panel load.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
5.7
SLASE46 – FEBRUARY 2015
Timing and Switching Characteristics
5.7.1
Power Supply Sequencing
TI recommends powering AVCC and DVCC pins from the same source. At a minimum, during power up, power
down, and device operation, the voltage difference between AVCC and DVCC must not exceed the limits
specified in Absolute Maximum Ratings. Exceeding the specified limits may cause malfunction of the device
including erroneous writes to RAM and FRAM.
5.7.2
Reset Timing
Table 5-1. Wake-up Time From Low-Power Modes and Reset
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
fMCLK ≥ 4 MHz
3
5
1 MHz < fMCLK <
4 MHz
4
6
150
160
µs
tWAKE-UP-FAST
Wake-up time from LPM2, LPM3,
or LPM4 to active mode (1)
PMMCOREV = SVSMLRRL = n
(where n = 0, 1, 2, or 3),
SVSLFP = 1
tWAKE-UP-SLOW
Wake-up time from LPM2, LPM3,
or LPM4 to active mode (2)
PMMCOREV = SVSMLRRL = n
(where n = 0, 1, 2, or 3),
SVSLFP = 0
tWAKE-UP-LPM4.5
Wake-up time from LPM4.5 to
active mode (3)
2
3
ms
tWAKE-UP-RESET
Wake-up time from RST or BOR
event to active mode (3)
2
3
ms
(1)
(2)
(3)
µs
This value represents the time from the wake-up event to the first active edge of MCLK. The wake-up time depends on the performance
mode of the low-side supervisor (SVSL) and low-side monitor (SVML). Fastest wake-up times are possible with SVSLand SVMLin fullperformance mode or disabled when operating in AM, LPM0, and LPM1. Various options are available for SVSLand SVML while
operating in LPM2, LPM3, and LPM4. See the Power Management Module and Supply Voltage Supervisor chapter in the MSP430x5xx
and MSP430x6xx Family User's Guide (SLAU208).
This value represents the time from the wake-up event to the first active edge of MCLK. The wake-up time depends on the performance
mode of the low side supervisor (SVSL) and low side monitor (SVML). In this case, the SVSLand SVML are in normal mode (low current)
mode when operating in AM, LPM0, and LPM1. Various options are available for SVSLand SVML while operating in LPM2, LPM3, and
LPM4. See the Power Management Module and Supply Voltage Supervisorchapter in the MSP430x5xx and MSP430x6xx Family User's
Guide (SLAU208).
This value represents the time from the wake-up event to the reset vector execution.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
37
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.7.3
www.ti.com
Clock Specifications
Table 5-2. Crystal Oscillator, XT1, Low-Frequency Mode (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
ΔIDVCC.LF
Differential XT1 oscillator
crystal current consumption
from lowest drive setting, LF
mode
TEST CONDITIONS
VCC
MIN
fOSC = 32768 Hz, XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 1, TA = 25°C
fOSC = 32768 Hz, XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 2, TA = 25°C
3.0 V
0.170
0.290
XTS = 0, XT1BYPASS = 0
32768
XT1 oscillator crystal
frequency, LF mode
fXT1,LF,SW
XT1 oscillator logic-level
square-wave input frequency, XTS = 0, XT1BYPASS = 1 (2)
LF mode
OALF
Oscillation allowance for
LF crystals (4)
(3)
10
fFault,LF
tSTART,LF
210
XTS = 0, XT1BYPASS = 0, XT1DRIVEx = 1,
fXT1,LF = 32768 Hz, CL,eff = 12 pF
300
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
38
XTS = 0, XCAPx = 2
8.5
XTS = 0, XCAPx = 3
12.0
Oscillator fault frequency,
LF mode (7)
XTS = 0 (8)
fOSC = 32768 Hz, XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 0, TA = 25°C, CL,eff = 6 pF
fOSC = 32768 Hz, XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 3, TA = 25°C, CL,eff = 12 pF
µA
Hz
50
kHz
1
5.5
Duty cycle, LF mode
UNIT
kΩ
XTS = 0, XCAPx = 1
XTS = 0, Measured at ACLK,
fXT1,LF = 32768 Hz
Start-up time, LF mode
32.768
XTS = 0, XT1BYPASS = 0, XT1DRIVEx = 0,
fXT1,LF = 32768 Hz, CL,eff = 6 pF
XTS = 0, XCAPx = 0 (6)
Integrated effective load
capacitance, LF mode (5)
MAX
0.075
fOSC = 32768 Hz, XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 3, TA = 25°C
fXT1,LF0
CL,eff
TYP
pF
30%
70%
10
10000
Hz
1000
3.0 V
ms
500
To improve EMI on the XT1 oscillator, the following guidelines should be observed.
• Keep the trace between the device and the crystal as short as possible.
• Design a good ground plane around the oscillator pins.
• Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
• Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
• Use assembly materials and processes that avoid any parasitic load on the oscillator XIN and XOUT pins.
• If conformal coating is used, ensure that it does not induce capacitive or resistive leakage between the oscillator pins.
When XT1BYPASS is set, XT1 circuits are automatically powered down. Input signal is a digital square wave with parametrics defined in
the Schmitt-Trigger Inputs section of this datasheet.
Maximum frequency of operation of the entire device cannot be exceeded.
Oscillation allowance is based on a safety factor of 5 for recommended crystals. The oscillation allowance is a function of the
XT1DRIVEx settings and the effective load. In general, comparable oscillator allowance can be achieved based on the following
guidelines, but should be evaluated based on the actual crystal selected for the application:
• For XT1DRIVEx = 0, CL,eff ≤ 6 pF
• For XT1DRIVEx = 1, 6 pF ≤ CL,eff ≤ 9 pF
• For XT1DRIVEx = 2, 6 pF ≤ CL,eff ≤ 10 pF
• For XT1DRIVEx = 3, CL,eff ≥ 6 pF
Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, TI recommends verifying the correct load by measuring the ACLK frequency. For a
correct setup, the effective load capacitance should always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency but also applies to operation with crystals.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 5-3. Internal Very-Low-Power Low-Frequency Oscillator (VLO)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fVLO
VLO frequency
dfVLO/dT
VLO frequency temperature drift
dfVLO/dVCC VLO frequency supply voltage drift
Duty cycle
(1)
(2)
TEST CONDITIONS
Measured at ACLK
VCC
MIN
TYP
MAX
6
9.4
15
1.8 V to 3.6 V
(1)
1.8 V to 3.6 V
0.5
Measured at ACLK (2)
1.8 V to 3.6 V
4
Measured at ACLK
1.8 V to 3.6 V
Measured at ACLK
30%
UNIT
kHz
%/°C
%/V
70%
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(85°C – (–40°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8 V to 3.6 V)) / MIN(1.8 V to 3.6 V) / (3.6 V – 1.8 V)
Table 5-4. Internal Reference, Low-Frequency Oscillator (REFO)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
IREFO
fREFO
dfREFO/dT
dfREFO/dVCC
tSTART
(1)
(2)
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
REFO oscillator current
consumption
TA = 25°C
1.8 V to 3.6 V
3
µA
REFO frequency calibrated
Measured at ACLK
1.8 V to 3.6 V
32768
Hz
Full temperature range
1.8 V to 3.6 V
REFO absolute tolerance calibrated
REFO frequency temperature drift
TA = 25°C
Measured at ACLK (1)
1.8 V to 3.6 V
(2)
1.8 V to 3.6 V
REFO frequency supply voltage drift Measured at ACLK
±3.5%
3V
Duty cycle
Measured at ACLK
1.8 V to 3.6 V
REFO start-up time
40%/60% duty cycle
1.8 V to 3.6 V
±1.5%
0.01
%/°C
1.0
40%
50%
%/V
60%
25
µs
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(85°C – (–40°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8 V to 3.6 V)) / MIN(1.8 V to 3.6 V) / (3.6 V – 1.8 V)
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
39
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-5. DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fDCO(0,0)
TEST CONDITIONS
DCO frequency (0, 0) (1)
(1)
MAX
UNIT
DCORSELx = 0, DCOx = 0, MODx = 0
0.07
MIN
TYP
0.20
MHz
fDCO(0,31)
DCO frequency (0, 31)
DCORSELx = 0, DCOx = 31, MODx = 0
0.70
1.70
MHz
fDCO(1,0)
DCO frequency (1, 0) (1)
DCORSELx = 1, DCOx = 0, MODx = 0
0.15
0.36
MHz
fDCO(1,31)
DCO frequency (1, 31) (1)
DCORSELx = 1, DCOx = 31, MODx = 0
1.47
3.45
MHz
fDCO(2,0)
DCO frequency (2, 0) (1)
DCORSELx = 2, DCOx = 0, MODx = 0
0.32
0.75
MHz
(1)
fDCO(2,31)
DCO frequency (2, 31)
DCORSELx = 2, DCOx = 31, MODx = 0
3.17
7.38
MHz
fDCO(3,0)
DCO frequency (3, 0) (1)
DCORSELx = 3, DCOx = 0, MODx = 0
0.64
1.51
MHz
fDCO(3,31)
DCO frequency (3, 31) (1)
DCORSELx = 3, DCOx = 31, MODx = 0
6.07
14.0
MHz
(1)
fDCO(4,0)
DCO frequency (4, 0)
DCORSELx = 4, DCOx = 0, MODx = 0
1.3
3.2
MHz
fDCO(4,31)
DCO frequency (4, 31) (1)
DCORSELx = 4, DCOx = 31, MODx = 0
12.3
28.2
MHz
fDCO(5,0)
DCO frequency (5, 0) (1)
DCORSELx = 5, DCOx = 0, MODx = 0
2.5
6.0
MHz
(1)
fDCO(5,31)
DCO frequency (5, 31)
DCORSELx = 5, DCOx = 31, MODx = 0
23.7
54.1
MHz
fDCO(6,0)
DCO frequency (6, 0) (1)
DCORSELx = 6, DCOx = 0, MODx = 0
4.6
10.7
MHz
fDCO(6,31)
DCO frequency (6, 31) (1)
DCORSELx = 6, DCOx = 31, MODx = 0
39.0
88.0
MHz
fDCO(7,0)
DCO frequency (7, 0) (1)
DCORSELx = 7, DCOx = 0, MODx = 0
8.5
19.6
MHz
(1)
fDCO(7,31)
DCO frequency (7, 31)
DCORSELx = 7, DCOx = 31, MODx = 0
60
135
MHz
SDCORSEL
Frequency step between range
DCORSEL and DCORSEL + 1
SRSEL = fDCO(DCORSEL+1,DCO)/fDCO(DCORSEL,DCO)
1.2
2.3
ratio
SDCO
Frequency step between tap
DCO and DCO + 1
SDCO = fDCO(DCORSEL,DCO+1)/fDCO(DCORSEL,DCO)
1.02
1.12
ratio
40%
Duty cycle
Measured at SMCLK
dfDCO/dT
DCO frequency temperature drift
fDCO = 1 MHz
0.1
%/°C
dfDCO/dVCORE
DCO frequency voltage drift
fDCO = 1 MHz
1.9
%/V
(1)
50%
60%
When selecting the proper DCO frequency range (DCORSELx), the target DCO frequency, fDCO, should be set to reside within the
range of fDCO(n, 0),MAX ≤ fDCO ≤ fDCO(n, 31),MIN, where fDCO(n, 0),MAX represents the maximum frequency specified for the DCO frequency,
range n, tap 0 (DCOx = 0) and fDCO(n,31),MIN represents the minimum frequency specified for the DCO frequency, range n, tap 31
(DCOx = 31). This ensures that the target DCO frequency resides within the range selected. It should also be noted that if the actual
fDCOfrequency for the selected range causes the FLL or the application to select tap 0 or 31, the DCO fault flag is set to report that the
selected range is at its minimum or maximum tap setting.
Typical DCO Frequency, VCC = 3.0 V, TA = 25°C
100
fDCO – MHz
10
DCOx = 31
1
0.1
DCOx = 0
0
1
2
3
4
5
6
7
DCORSEL
Figure 5-2. Typical DCO Frequency
40
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
5.7.4
SLASE46 – FEBRUARY 2015
Digital I/O Ports
Table 5-6. Schmitt-Trigger Inputs, General-Purpose I/O
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT+
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ – VIT–)
RPull
Pullup or pulldown resistor (1)
For pullup: VIN = VSS
For pulldown: VIN = VCC
CI
Input capacitance
VIN = VSS or VCC
(1)
VCC
MIN
1.8 V
0.80
TYP
1.40
3V
1.50
2.10
1.8 V
0.45
1.00
3V
0.75
1.65
1.8 V
0.3
0.85
3V
0.4
1.0
20
35
MAX
UNIT
V
V
V
50
kΩ
5
pF
Also applies to RST pin when pullup or pulldown resistor is enabled.
Table 5-7. Inputs, Ports P1 and P2 (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
t(int)
(1)
(2)
PARAMETER
TEST CONDITIONS
VCC
External interrupt timing (2)
Port P1, P2: P1.x to P2.x, External trigger pulse duration
to set interrupt flag
2.2 V, 3 V
MIN
MAX
UNIT
20
ns
Some devices may contain additional ports with interrupts. See the block diagram and terminal function descriptions.
An external signal sets the interrupt flag every time the minimum interrupt pulse duration t(int) is met. It might be set by trigger signals
shorter than t(int).
Table 5-8. Leakage Current, General-Purpose I/O
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.y)
(1)
(2)
TEST CONDITIONS
High-impedance leakage current
See
VCC
(1) (2)
MIN
1.8 V, 3 V
MAX
UNIT
±50
nA
The leakage current is measured with VSSor VCC applied to the corresponding pins, unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup or pulldown resistor is
disabled.
Table 5-9. Outputs, General-Purpose I/O (Full Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
I(OHmax) = –3 mA
VOH
High-level output voltage
I(OHmax) = –10 mA (1)
I(OHmax) = –5 mA (1)
I(OHmax) = –15 mA (1)
I(OLmax) = 3 mA (2)
VOL
Low-level output voltage
I(OLmax) = 10 mA (3)
I(OLmax) = 5 mA
(2)
(3)
1.8 V
3V
1.8 V
(2)
I(OLmax) = 15 mA (3)
(1)
VCC
(1)
3V
MIN
MAX
VCC – 0.25
VCC
VCC – 0.60
VCC
VCC – 0.25
VCC
VCC – 0.60
VCC
VSS
VSS + 0.25
VSS
VSS + 0.60
VSS
VSS + 0.25
VSS
VSS + 0.60
UNIT
V
V
The maximum total current, I(OHmax), for all outputs combined should not exceed ±20 mA to hold the maximum voltage drop specified.
SeeSection 5.3 for more details.
The maximum total current, I(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop specified.
The maximum total current, I(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage drop specified.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
41
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.7.4.1
www.ti.com
Typical Characteristics, General-Purpose I/O (Full Drive Strength)
0
-10
-5
IOH – High-Level Output Current – mA
IOH – High-Level Output Current – mA
0
-10
-15
TA = 85°C
-20
-20
-30
-40
TA = 85°C
-50
TA = 25°C
TA = 25°C
-60
-25
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
0
1.8
0.5
VCC = 1.8 V
Full Drive Strength
Figure 5-3. High-Level Output Current vs High-Level Output
Voltage
2
VCC = 3 V
2.5
3
Full Drive Strength
60
50
20
IOL – Low-Level Output Current – mA
IOL – Low-Level Output Current – mA
1.5
Figure 5-4. High-Level Output Current vs High-Level Output
Voltage
25
TA = 25°C
TA = 85°C
15
10
5
TA = 25°C
TA = 85°C
40
30
20
10
0
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
0
0.5
VCC = 1.8 V
Full Drive Strength
Figure 5-5. Low-Level Output Current vs Low-Level Output
Voltage
Specifications
1
1.5
2
2.5
3
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
42
1
VOH – High-Level Output Voltage – V
VOH – High-Level Output Voltage – V
VCC = 3 V
Full Drive Strength
Figure 5-6. Low-Level Output Current vs Low-Level Output
Voltage
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 5-10. Outputs, General-Purpose I/O (Reduced Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
I(OHmax) = –1 mA (2)
VOH
High-level output voltage
I(OHmax) = –3 mA (2)
I(OHmax) = –2 mA (2)
I(OHmax) = –6 mA (2)
I(OLmax) = 1 mA (3)
VOL
Low-level output voltage
I(OLmax) = 3 mA (4)
I(OLmax) = 2 mA (3)
I(OLmax) = 6 mA (4)
(1)
(2)
(3)
(4)
VCC
1.8 V
3.0 V
1.8 V
3.0 V
MIN
MAX
VCC – 0.25
VCC
VCC – 0.60
VCC
VCC – 0.25
VCC
VCC – 0.60
VCC
VSS
VSS + 0.25
VSS
VSS + 0.60
VSS
VSS + 0.25
VSS
VSS + 0.60
UNIT
V
V
Selecting reduced drive strength may reduce EMI.
The maximum total current, I(OHmax), for all outputs combined should not exceed ±20 mA to hold the maximum voltage drop specified.
SeeSection 5.3 for more details.
The maximum total current, I(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop specified.
The maximum total current, I(OLmax), for all outputs combined, should not exceed ±100 mA to hold the maximum voltage drop specified.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
43
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.7.4.2
www.ti.com
Typical Characteristics, General-Purpose I/O (Reduced Drive Strength)
0
0
IOH – High-Level Output Current – mA
IOH – High-Level Output Current – mA
-1
-2
-3
-4
-5
TA = 85°C
-6
-5
-10
-15
TA = 85°C
-20
TA = 25°C
-7
TA = 25°C
-8
-25
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
0
0.5
VOH – High-Level Output Voltage – V
VCC = 1.8 V
Reduced Drive Strength
Figure 5-7. High-Level Output Current vs High-Level Output
Voltage
VCC = 3 V
2
2.5
3
Reduced Drive Strength
20
18
7
TA = 25°C
TA = 25°C
IOL – Low-Level Output Current – mA
IOL – Low-Level Output Current – mA
1.5
Figure 5-8. High-Level Output Current vs High-Level Output
Voltage
8
6
TA = 85°C
5
4
3
2
1
16
TA = 85°C
14
12
10
8
6
4
2
0
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
0
0.5
VCC = 1.8 V
Reduced Drive Strength
Figure 5-9. Low-Level Output Current vs Low-Level Output
Voltage
Specifications
1
1.5
2
2.5
3
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
44
1
VOH – High-Level Output Voltage – V
VCC = 3 V
Reduced Drive Strength
Figure 5-10. Low-Level Output Current vs Low-Level Output
Voltage
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 5-11. Output Frequency, General-Purpose I/O
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fPx.y
Port output frequency (with load)
fPort_CLK
(1)
(2)
Clock output frequency
TEST CONDITIONS
See (1)
(2)
ACLK, SMCLK, MCLK,
CL = 20 pF (2)
MIN
MAX
VCC = 1.8 V,
PMMCOREVx = 0
16
VCC = 3 V,
PMMCOREVx = 3
25
VCC = 1.8 V,
PMMCOREVx = 0
16
VCC = 3 V,
PMMCOREVx = 3
25
UNIT
MHz
MHz
A resistive divider with 2 × R1 between VCC and VSS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. CL = 20 pF is connected to the output to VSS.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
45
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.7.5
www.ti.com
Power-Management Module (PMM)
Table 5-12. PMM, Brownout Reset (BOR)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
V(DVCC_BOR_IT–)
BORH on voltage, DVCC falling level
| dDVCC/dt | < 3 V/s
V(DVCC_BOR_IT+)
BORH off voltage, DVCC rising level
| dDVCC/dt | < 3 V/s
V(DVCC_BOR_hys)
BORH hysteresis
tRESET
(1)
0.80
TYP
1.30
60
Pulse duration required at RST/NMI pin to
accept a reset
(1)
MIN
MAX
UNIT
1.45
V
1.50
V
250
mV
2
µs
Pulse shorter than 2 µs might trigger reset.
Table 5-13. PMM, Core Voltage
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VCORE3(AM)
Core voltage, active mode, PMMCOREV = 3
2.4 V ≤ DVCC ≤ 3.6 V
1.93
V
VCORE2(AM)
Core voltage, active mode, PMMCOREV = 2
2.2 V ≤ DVCC ≤ 3.6 V
1.83
V
VCORE1(AM)
Core voltage, active mode, PMMCOREV = 1
2.0 V ≤ DVCC ≤ 3.6 V
1.62
V
VCORE0(AM)
Core voltage, active mode, PMMCOREV = 0
1.8 V ≤ DVCC ≤ 3.6 V
1.42
V
VCORE3(LPM)
Core voltage, low-current mode, PMMCOREV = 3
2.4 V ≤ DVCC ≤ 3.6 V
1.96
V
VCORE2(LPM)
Core voltage, low-current mode, PMMCOREV = 2
2.2 V ≤ DVCC ≤ 3.6 V
1.94
V
VCORE1(LPM)
Core voltage, low-current mode, PMMCOREV = 1
2.0 V ≤ DVCC ≤ 3.6 V
1.74
V
VCORE0(LPM)
Core voltage, low-current mode, PMMCOREV = 0
1.8 V ≤ DVCC ≤ 3.6 V
1.54
V
Table 5-14. PMM, SVS High Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
SVSHE = 0, DVCC = 3.6 V
I(SVSH)
SVS current consumption
V(SVSH_IT+)
SVSH on voltage level (1)
SVSH off voltage level (1)
tpd(SVSH)
SVSH propagation delay
t(SVSH)
SVSH on or off delay time
dVDVCC/dt
DVCC rise time
(1)
46
MAX
0
SVSHE = 1, DVCC = 3.6 V, SVSHFP = 0
1.5
µA
SVSHE = 1, SVSHRVL = 0
1.60
1.65
1.70
SVSHE = 1, SVSHRVL = 1
1.77
1.84
1.90
SVSHE = 1, SVSHRVL = 2
1.97
2.04
2.10
SVSHE = 1, SVSHRVL = 3
2.09
2.16
2.23
SVSHE = 1, SVSMHRRL = 0
1.68
1.74
1.80
SVSHE = 1, SVSMHRRL = 1
1.89
1.95
2.01
SVSHE = 1, SVSMHRRL = 2
2.08
2.14
2.21
SVSHE = 1, SVSMHRRL = 3
2.21
2.27
2.34
SVSHE = 1, SVSMHRRL = 4
2.35
2.41
2.49
SVSHE = 1, SVSMHRRL = 5
2.65
2.72
2.80
SVSHE = 1, SVSMHRRL = 6
2.96
3.04
3.13
SVSHE = 1, SVSMHRRL = 7
2.96
3.04
3.13
SVSHE = 1, dVDVCC/dt = 10 mV/µs, SVSHFP = 1
2.5
SVSHE = 1, dVDVCC/dt = 1 mV/µs, SVSHFP = 0
20
SVSHE = 0 → 1, SVSHFP = 1
12.5
SVSHE = 0 → 1, SVSHFP = 0
100
0
UNIT
nA
200
SVSHE = 1, DVCC = 3.6 V, SVSHFP = 1
V(SVSH_IT–)
TYP
V
V
µs
µs
1000
V/s
The SVSH settings available depend on the VCORE (PMMCOREVx) setting. Please refer to the Power Management Module and Supply
Voltage Supervisor chapter in the MSP430x5xx and MSP430x6xx Family User's Guide(SLAU208) on recommended settings and usage.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 5-15. PMM, SVM High Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
SVMHE = 0, DVCC = 3.6 V
I(SVMH)
SVMH current consumption
SVMH on or off voltage level (1)
SVMHE = 1, DVCC = 3.6 V, SVMHFP = 0
SVMH propagation delay
t(SVMH)
SVMH on or off delay time
(1)
UNIT
nA
200
1.5
µA
SVMHE = 1, SVSMHRRL = 0
1.68
1.74
1.80
SVMHE = 1, SVSMHRRL = 1
1.89
1.95
2.01
SVMHE = 1, SVSMHRRL = 2
2.08
2.14
2.21
SVMHE = 1, SVSMHRRL = 3
2.21
2.27
2.34
SVMHE = 1, SVSMHRRL = 4
2.35
2.41
2.49
SVMHE = 1, SVSMHRRL = 5
2.65
2.72
2.80
SVMHE = 1, SVSMHRRL = 6
2.96
3.04
3.13
SVMHE = 1, SVSMHRRL = 7
2.96
3.04
3.13
SVMHE = 1, SVMHOVPE = 1
tpd(SVMH)
MAX
0
SVMHE = 1, DVCC = 3.6 V, SVMHFP = 1
V(SVMH)
TYP
V
3.79
SVMHE = 1, dVDVCC/dt = 10 mV/µs, SVMHFP = 1
2.5
SVMHE = 1, dVDVCC/dt = 1 mV/µs, SVMHFP = 0
20
SVMHE = 0 → 1, SVMHFP = 1
12.5
SVMHE = 0 → 1, SVMHFP = 0
100
µs
µs
The SVMH settings available depend on the VCORE (PMMCOREVx) setting. Refer to the Power Management Module and Supply
Voltage Supervisor chapter in the MSP430x5xx and MSP430x6xx Family User's Guide(SLAU208) on recommended settings and usage.
Table 5-16. PMM, SVS Low Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
SVSLE = 0, PMMCOREV = 2
I(SVSL)
SVSL current consumption
tpd(SVSL)
SVSL propagation delay
t(SVSL)
SVSL on or off delay time
TYP
MAX
0
SVSLE = 1, PMMCOREV = 2, SVSLFP = 0
200
SVSLE = 1, PMMCOREV = 2, SVSLFP = 1
1.5
SVSLE = 1, dVCORE/dt = 10 mV/µs, SVSLFP = 1
2.5
SVSLE = 1, dVCORE/dt = 1 mV/µs, SVSLFP = 0
20
SVSLE = 0 → 1, SVSLFP = 1
12.5
SVSLE = 0 → 1, SVSLFP = 0
100
UNIT
nA
µA
µs
µs
Table 5-17. PMM, SVM Low Side
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SVMLE = 0, PMMCOREV = 2
I(SVML)
SVML current consumption
tpd(SVML)
SVML propagation delay
t(SVML)
SVML on or off delay time
MIN
TYP
MAX
0
SVMLE = 1, PMMCOREV = 2, SVMLFP = 0
200
SVMLE = 1, PMMCOREV = 2, SVMLFP = 1
1.5
SVMLE = 1, dVCORE/dt = 10 mV/µs, SVMLFP = 1
2.5
SVMLE = 1, dVCORE/dt = 1 mV/µs, SVMLFP = 0
20
SVMLE = 0 → 1, SVMLFP = 1
12.5
SVMLE = 0 → 1, SVMLFP = 0
100
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
UNIT
nA
µA
µs
µs
47
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
5.7.6
www.ti.com
Auxiliary Supplies Module
Table 5-18. Auxiliary Supplies, Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VCC
Supply voltage range for all supplies at pins DVCC, AVCC, AUX1, AUX2, AUX3
NOM
MAX
1.8
3.6
PMMCOREVx = 0
1.8
3.6
PMMCOREVx = 1
2.0
3.6
PMMCOREVx = 2
2.2
3.6
2.4
3.6
UNIT
V
VDSYS
Digital system supply voltage range,
VDSYS = VCC - RON×ILOAD
VASYS
Analog system supply voltage range, VASYS = VCC - RON × ILOAD
CVCC,CAUX
Recommended capacitor at pins DVCC, AVCC, AUX1, AUX2
4.7
µF
CVSYS
Recommended capacitor at pins VDSYS and VASYS
4.7
µF
CVCORE
Recommended capacitance at pin VCORE
0.47
µF
CAUX3
Recommended capacitor at pin AUX3
0.47
µF
PMMCOREVx = 3
Refer to modules
V
V
1/2
Table 5-19. Auxiliary Supplies, AUX3 (Backup Subsystem) Currents
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
IAUX3,RTCon
AUX3 current with RTC enabled
RTC and 32-kHz oscillator in
backup subsystem enabled
3V
IAUX3,RTCoff
AUX3 current with RTC disabled
RTC and 32-kHz oscillator in
backup subsystem disabled
3V
TA
MIN
MAX
25°C
0.83
85°C
0.95
25°C
110
85°C
165
UNIT
µA
nA
Table 5-20. Auxiliary Supplies, Auxiliary Supply Monitor
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ICC,Monitor
Average supply current for
monitoring circuitry drawn from
VDSYS
LOCKAUX = 0, AUXMRx = 0,
AUX0MD = 0, AUX1MD = 0, AUX2MD = 1,
VDSYS = DVCC, VASYS = AVCC,
Current measured at VDSYS pin
IMeas,Monitor
Average current drawn from
monitored supply during
measurement cycle
LOCKAUX = 0, AUXMRx = 0,
AUX0MD = 0, AUX1MD = 0, AUX2MD = 1,
VDSYS = DVCC, VASYS = AVCC,
AUXVCC1 = 3 V,
Current measured at AUXVCC1 pin
VMonitor
48
Auxiliary supply threshold level
Specifications
VCC
MIN
TYP
3V
MAX
UNIT
0.70
µA
0.11
µA
AUXLVLx = 0
1.67
1.74
1.80
AUXLVLx = 1
1.87
1.95
2.01
AUXLVLx = 2
2.06
2.14
2.21
AUXLVLx = 3
2.19
2.27
2.33
AUXLVLx = 4
2.33
2.41
2.48
AUXLVLx = 5
2.63
2.72
2.79
AUXLVLx = 6
2.91
3.02
3.10
AUXLVLx = 7
2.91
3.02
3.10
V
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
0.7
0.6
ICC, monitor – µA
0.5
0.4
0.3
0.2
0.1
0
1.8
2
2.2
2.4
2.6
2.8
VDSYS Voltage – V
3
3.2
3.4
3.6
3.2
3.4
3.6
Figure 5-11. VDSYS Voltage vs ICC,Monitor
120
Imeas, monitor – nA
100
80
60
40
20
0
1.8
2.0
2.2
2.4
2.6
2.8
AUXVCC1 Voltage – V
3.0
Figure 5-12. AUXVCC1 Voltage vs IMeas,Monitor
Table 5-21. Auxiliary Supplies, Switch ON-Resistance
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
RON,DVCC
ON-resistance of switch between DVCC
and VDSYS
ILOAD = ICORE + IIO = 10 mA + 10 mA = 20 mA
5
Ω
RON,DAUX1
ON-resistance of switch between AUX1
and VDSYS
ILOAD = ICORE + IIO = 10 mA + 10 mA = 20 mA
5
Ω
RON,DAUX2
ON-resistance of switch between AUX2
and VDSYS
ILOAD = ICORE + IIO = 10 mA + 10 mA = 20 mA
5
Ω
RON,AVCC
ON-resistance of switch between AVCC
and VASYS
ILOAD = IModules = 10 mA
5
Ω
RON,AAUX1
ON-resistance of switch between AUX1
and VASYS
ILOAD = IModules = 5 mA
20
Ω
RON,AAUX2
ON-resistance of switch between AUX2
and VASYS
ILOAD = IModules = 5 mA
20
Ω
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
49
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-22. Auxiliary Supplies, Switching Time
over operating free-air temperature range (unless otherwise noted)
PARAMETER
MIN
tSwitch
Time from occurence of trigger (SVM or software) to "new" supply connected to system supplies
tRecover
"Recovery time" after a switch over takes place; during this time, no further switching takes place
MAX
UNIT
100
ns
200
450
µs
TYP
MAX
UNIT
50
100
nA
450
730
nA
UNIT
Table 5-23. Auxiliary Supplies, Switch Leakage
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ISW,Lkg
Current into DVCC, AVCC, AUX1 or AUX2 if
not selected
IVmax
Current drawn from highest supply
MIN
Per supply (but not the highest supply)
Table 5-24. Auxiliary Supplies, Auxiliary Supplies to ADC10_A
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Supply voltage divider
V3 = VSupply/3
V3
RV3
Load resistance
tSample,V3
Sampling time required if V3
selected
VCC
MIN
TYP
MAX
1.8 V
0.58
0.60
0.62
3.0 V
0.98
1.00
1.02
3.6 V
1.18
1.20
1.22
AUXADCRx = 0
18
AUXADCRx = 1
1.5
AUXADCRx = 2
0.6
AUXADC = 1,
ADC10ON = 1,
INCH = 0Ch,
Error of conversion
result ≤ 1 LSB
AUXADCRx = 0
1000
AUXADCRx = 1
1000
AUXADCRx = 2
1000
V
kΩ
ns
Table 5-25. Auxiliary Supplies, Charge Limiting Resistor
over operating free-air temperature range (unless otherwise noted)
PARAMETER
RCHARGE
50
Charge limiting resistor
Specifications
TEST CONDITIONS
VCC
MIN
TYP
MAX
CHCx = 1
3V
5
CHCx = 2
3V
10
CHCx = 3
3V
20
UNIT
kΩ
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
5.7.7
SLASE46 – FEBRUARY 2015
Timer_A Module
Table 5-26. Timer_A
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTA
Timer_A input clock frequency
Internal: SMCLK, ACLK
External: TACLK
Duty cycle = 50% ± 10%
tTA,cap
Timer_A capture timing
All capture inputs, Minimum pulse
duration required for capture
5.7.8
VCC
1.8 V, 3 V
1.8 V, 3 V
MIN
TYP
MAX
UNIT
25
MHz
20
ns
eUSCI Module
Table 5-27. eUSCI (UART Mode) Recommended Operating Conditions
PARAMETER
feUSCI
eUSCI input clock frequency
fBITCLK
BITCLK clock frequency
(equals baud rate in MBaud)
CONDITIONS
VCC
MIN
TYP
Internal: SMCLK, ACLK
External: UCLK
Duty cycle = 50% ± 10%
MAX
UNIT
fSYSTEM
MHz
5
MHz
UNIT
Table 5-28. eUSCI (UART Mode) Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
UCGLITx = 0
tt
UART receive deglitch time (1)
UCGLITx = 1
UCGLITx = 2
UCGLITx = 3
(1)
2 V, 3 V
MIN
TYP
MAX
10
15
25
30
50
85
50
80
150
70
120
200
ns
Pulses on the UART receive input (UCxRX) shorter than the UART receive deglitch time are suppressed. To ensure that pulses are
correctly recognized their width should exceed the maximum specification of the deglitch time.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
51
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-29. eUSCI (SPI Master Mode) Recommended Operating Conditions
PARAMETER
feUSCI
eUSCI input clock frequency
CONDITIONS
VCC
MIN
TYP
Internal: SMCLK, ACLK
Duty cycle = 50% ± 10%
MAX
UNIT
fSYSTEM
MHz
MAX
UNIT
Table 5-30. eUSCI (SPI Master Mode) Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
VCC
MIN
2 V, 3 V
150
tSTE,LEAD
STE lead time, STE active to
clock
UCSTEM = 0, UCMODEx = 01 or 10
UCSTEM = 1, UCMODEx = 01 or 10
2 V, 3 V
150
tSTE,LAG
STE lag time, Last clock to
STE inactive
UCSTEM = 0, UCMODEx = 01 or 10
2 V, 3 V
200
UCSTEM = 1, UCMODEx = 01 or 10
2 V, 3 V
200
UCSTEM = 0, UCMODEx = 01 or 10
tSTE,ACC
STE access time, STE active
to SIMO data out
UCSTEM = 1, UCMODEx = 01 or 10
STE disable time, STE
inactive to SIMO high
impedance
tSTE,DIS
UCSTEM = 0, UCMODEx = 01 or 10
UCSTEM = 1, UCMODEx = 01 or 10
tSU,MI
SOMI input data setup time
tHD,MI
SOMI input data hold time
tVALID,MO
SIMO output data valid time (2) UCLK edge to SIMO valid, CL = 20 pF
tHD,MO
SIMO output data hold time (3)
(1)
(2)
(3)
52
CL = 20 pF
TYP
ns
ns
2V
50
3V
30
2V
50
3V
30
2V
40
3V
25
2V
40
3V
25
2V
50
3V
30
2V
0
3V
0
ns
9
3V
5
0
3V
0
ns
ns
2V
2V
ns
ns
ns
fUCxCLK = 1/2tLO/HI with tLO/HI = max(tVALID,MO(eUSCI) + tSU,SI(Slave), tSU,MI(eUSCI) + tVALID,SO(Slave)).
For the slave parameters tSU,SI(Slave) and tVALID,SO(Slave) refer to the SPI parameters of the attached slave.
Specifies the time to drive the next valid data to the SIMO output after the output changing UCLK clock edge. See the timing diagrams
in Figure 5-15 and Figure 5-16.
Specifies how long data on the SIMO output is valid after the output changing UCLK clock edge. Negative values indicate that the data
on the SIMO output can become invalid before the output changing clock edge observed on UCLK. See the timing diagrams in Figure 515 and Figure 5-16.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
UCMODEx = 01
tSTE,LEAD
STE
tSTE,LAG
UCMODEx = 10
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW/HIGH
tLOW/HIGH
tSU,MI
tHD,MI
SOMI
tSTE,DIS
tVALID,MO
tSTE,ACC
SIMO
Figure 5-13. SPI Master Mode, CKPH = 0
UCMODEx = 01
tSTE,LEAD
STE
tSTE,LAG
UCMODEx = 10
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW/HIGH
tLOW/HIGH
tSU,MI
tHD,MI
SOMI
tSTE,ACC
tVALID,MO
tSTE,DIS
SIMO
Figure 5-14. SPI Master Mode, CKPH = 1
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
53
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-31. eUSCI (SPI Slave Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
VCC
tSTE,LEAD
STE lead time, STE active to clock
tSTE,LAG
STE lag time, Last clock to STE inactive
tSTE,ACC
STE access time, STE active to SOMI data out
tSTE,DIS
STE disable time, STE inactive to SOMI high
impedance
tSU,SI
SIMO input data setup time
tHD,SI
SIMO input data hold time
tVALID,SO
SOMI output data valid time (2)
UCLK edge to SOMI valid,
CL = 20 pF
tHD,SO
SOMI output data hold time (3)
CL = 20 pF
(1)
(2)
(3)
MIN
2.0 V
4
3.0 V
3
2.0 V
0
3.0 V
0
MAX
ns
ns
2.0 V
46
3.0 V
24
2.0 V
38
3.0 V
25
2.0 V
2
3.0 V
1
2.0 V
2
3.0 V
2
55
32
3.0 V
16
ns
ns
3.0 V
24
ns
ns
2.0 V
2.0 V
UNIT
ns
ns
fUCxCLK = 1/2tLO/HI with tLO/HI = max(tVALID,MO(Master) + tSU,SI(eUSCI), tSU,MI(Master) + tVALID,SO(eUSCI)).
For the master parameters tSU,MI(Master) and tVALID,MO(Master) refer to the SPI parameters of the attached slave.
Specifies the time to drive the next valid data to the SOMI output after the output changing UCLK clock edge. Refer to the timing
diagrams in Figure 5-15 and Figure 5-16.
Specifies how long data on the SOMI output is valid after the output changing UCLK clock edge. Refer to the timing diagrams in
Figure 5-15 and Figure 5-16.
UCMODEx = 01
tSTE,LEAD
STE
tSTE,LAG
UCMODEx = 10
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW/HIGH
tSU,SIMO
tLOW/HIGH
tHD,SIMO
SIMO
tACC
tVALID,SOMI
tDIS
SOMI
Figure 5-15. SPI Slave Mode, CKPH = 0
54
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
UCMODEx = 01
tSTE,LEAD
STE
tSTE,LAG
UCMODEx = 10
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW/HIGH
tLOW/HIGH
tHD,SI
tSU,SI
SIMO
tACC
tVALID,SO
tDIS
SOMI
Figure 5-16. SPI Slave Mode, CKPH = 1
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
55
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-32. eUSCI (I2C Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5-17)
PARAMETER
TEST CONDITIONS
feUSCI
eUSCI input clock frequency
fSCL
SCL clock frequency
Hold time (repeated) START
tSU,STA
Setup time for a repeated START
tHD,DAT
Data hold time
Data setup time
tSU,STO
Setup time for STOP
fSCL = 100 kHz
fSCL > 100 kHz
fSCL = 100 kHz
fSCL > 100 kHz
TYP
2 V, 3 V
2 V, 3 V
400
kHz
µs
µs
1.4
5.0
fSCL > 100 kHz
2 V, 3 V
1.3
µs
µs
5.2
µs
1.7
UCGLITx = 0
75
220
UCGLITx = 1
35
120
30
60
UCGLITx = 2
2 V, 3 V
20
UCCLTOx = 2
30
2 V, 3 V
33
UCCLTOx = 3
tSU,STA
tHD,STA
ns
35
UCCLTOx = 1
Clock low timeout
MHz
5.1
0.4
UCGLITx = 3
tTIMEOUT
fSYSTEM
1.5
2 V, 3 V
fSCL > 100 kHz
UNIT
0
2 V, 3 V
2 V, 3 V
MAX
5.1
fSCL = 100 kHz
fSCL = 100 kHz
Pulse duration of spikes suppressed by input
filter
tSP
MIN
2 V, 3 V
tHD,STA
tSU,DAT
VCC
Internal: SMCLK, ACLK
External: UCLK
Duty cycle = 50% ± 10%
ms
37
tHD,STA
tBUF
SDA
tLOW
tHIGH
tSP
SCL
tSU,DAT
tSU,STO
tHD,DAT
Figure 5-17. I2C Mode Timing
56
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
5.7.9
SLASE46 – FEBRUARY 2015
LCD Controller
Table 5-33. LCD_C Recommended Operating Conditions
PARAMETER
CONDITIONS
MIN
NOM
MAX
UNIT
VCC,LCD_C,CP en,3.6
Supply voltage range, charge
pump enabled, VLCD ≤ 3.6 V
LCDCPEN = 1, 0000 < VLCDx ≤ 1111
(charge pump enabled, VLCD ≤ 3.6 V)
2.2
3.6
V
VCC,LCD_C,CP en,3.3
Supply voltage range, charge
pump enabled, VLCD ≤ 3.3 V
LCDCPEN = 1, 0000 < VLCDx ≤ 1100
(charge pump enabled, VLCD ≤ 3.3 V)
2.0
3.6
V
VCC,LCD_C,int.
bias
Supply voltage range, internal
biasing, charge pump disabled
LCDCPEN = 0, VLCDEXT = 0
2.4
3.6
V
VCC,LCD_C,ext.
bias
Supply voltage range, external
biasing, charge pump disabled
LCDCPEN = 0, VLCDEXT = 0
2.4
3.6
V
VCC,LCD_C,VLCDEXT
Supply voltage range, external
LCD voltage, internal or external
biasing, charge pump disabled
LCDCPEN = 0, VLCDEXT = 1
2.0
3.6
V
VLCDCAP/R33
External LCD voltage at
LCDCAP/R33, internal or external
biasing, charge pump disabled
LCDCPEN = 0, VLCDEXT = 1
2.4
3.6
V
CLCDCAP
Capacitor on LCDCAP when
charge pump enabled
LCDCPEN = 1, VLCDx > 0000
(charge pump enabled)
10
µF
fFrame
LCD frame frequency range
fLCD = 2 × mux × fFRAME
with mux = 1 (static), 2, 3, 4 up to 8
100
Hz
fACLK,in
ACLK input frequency range
CPanel
Panel capacitance
4.7
0
40
kHz
100-Hz frame frequency
30
32
10000
pF
VCC +
0.2
V
VR33
Analog input voltage at R33
LCDCPEN = 0, VLCDEXT = 1
2.4
VR23,1/3bias
Analog input voltage at R23
LCDREXT = 1, LCDEXTBIAS = 1,
LCD2B = 0
VR13
VR03 + 2/3 ×
(VR33 –
VR03)
VR33
V
VR13,1/3bias
Analog input voltage at R13 with
1/3 biasing
LCDREXT = 1, LCDEXTBIAS = 1,
LCD2B = 0
VR03
VR03 + 1/3 ×
(VR33 –
VR03)
VR23
V
VR13,1/2bias
Analog input voltage at R13 with
1/2 biasing
LCDREXT = 1, LCDEXTBIAS = 1,
LCD2B = 1
VR03
VR03 + 1/2 ×
(VR33 –
VR03)
VR33
V
VR03
Analog input voltage at R03
R0EXT = 1
VSS
VLCD-VR03
Voltage difference between VLCD
and R03
LCDCPEN = 0, R0EXT = 1
2.4
VLCDREF/R13
External LCD reference voltage
applied at LCDREF/R13
VLCDREFx = 01
0.8
V
1.2
VCC +
0.2
V
1.5
V
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
57
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-34. LCD_C Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
VLCD
LCD voltage
TEST CONDITIONS
VCC
VCC
LCDCPEN = 1, VLCDx = 0001
2 V to 3.6 V
2.58
LCDCPEN = 1, VLCDx = 0010
2 V to 3.6 V
2.64
LCDCPEN = 1, VLCDx = 0011
2 V to 3.6 V
2.71
LCDCPEN = 1, VLCDx = 0100
2 V to 3.6 V
2.78
LCDCPEN = 1, VLCDx = 0101
2 V to 3.6 V
2.83
LCDCPEN = 1, VLCDx = 0110
2 V to 3.6 V
2.90
LCDCPEN = 1, VLCDx = 0111
2 V to 3.6 V
2.96
LCDCPEN = 1, VLCDx = 1000
2 V to 3.6 V
3.02
LCDCPEN = 1, VLCDx = 1001
2 V to 3.6 V
3.07
LCDCPEN = 1, VLCDx = 1010
2 V to 3.6 V
3.14
LCDCPEN = 1, VLCDx = 1011
2 V to 3.6 V
3.21
LCDCPEN = 1, VLCDx = 1100
2 V to 3.6 V
3.27
LCDCPEN = 1, VLCDx = 1101
2.2 V to 3.6 V
3.32
LCDCPEN = 1, VLCDx = 1110
2.2 V to 3.6 V
3.38
LCDCPEN = 1, VLCDx = 1111
2.2 V to 3.6 V
3.44
ICC,Peak,CP
LCDCPEN = 1, VLCDx = 1111
tLCD,CP,on
Time to charge CLCD when
discharged
CLCD = 4.7µF, LCDCPEN = 0→1,
VLCDx = 1111
ICP,Load
Maximum charge pump load
current
LCDCPEN = 1, VLCDx = 1111
RLCD,Seg
LCD driver output impedance,
segment lines
LCDCPEN = 1, VLCDx = 1000,
ILOAD = ±10 µA
2.2 V
RLCD,COM
LCD driver output impedance,
common lines
LCDCPEN = 1, VLCDx = 1000,
ILOAD = ±10 µA
2.2 V
Specifications
TYP
2.4 V to 3.6 V
Peak supply currents due to
charge pump activities
58
MIN
VLCDx = 0000, VLCDEXT = 0
2.2 V
150
UNIT
V
3.6
400
2.2 V
2.2 V
MAX
µA
500
50
ms
µA
10
kΩ
10
kΩ
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
5.7.10 SD24_B Module
Table 5-35. SD24_B Power Supply and Recommended Operating Conditions
MIN
AVCC
Analog supply voltage
fSD
TYP
MAX
UNIT
2.4
3.6
V
Modulator clock frequency (1)
0.03
2.3
MHz
VI
Absolute input voltage range
AVSS - 1V
AVCC
V
VIC
Common-mode input voltage range
AVSS - 1V
AVCC
V
VID,FS
Differential full-scale input voltage
-VREF/GAIN
+VREF/GAIN
CREF
(3)
VID = VI,A+ - VI,A-
Differential input voltage for specified
performance (2)
VID
(1)
(2)
AVCC = DVCC, AVSS = DVSS = 0 V
SD24REFS = 1
VREF load capacitance (3)
SD24GAINx = 1
±910
±920
SD24GAINx = 2
±455
±460
SD24GAINx = 4
±227
±230
SD24GAINx = 8
±113
±115
SD24GAINx = 16
±57
±58
SD24GAINx = 32
±28
±29
SD24GAINx = 64
±14
±14.5
SD24GAINx = 128
±7
±7.2
SD24REFS = 1
100
PARAMETER
Input capacitance
TEST CONDITIONS
(1)
VCC
MIN
ZID
(1)
Input impedance
(Pin A+ or A- to AVSS)
Differential input impedance
(Pin A+ to pin A-)
TYP
SD24GAINx = 1
5
SD24GAINx = 2
5
SD24GAINx = 4
5
SD24GAINx = 8
5
SD24GAINx = 16
5
SD24GAINx = 32, 64, 128
ZI
nF
Modulator clock frequency: MIN = 32.768 kHz - 10% ≈ 30 kHz. MAX = 32.768 kHz × 64 + 10% ≈ 2.3 MHz
The full-scale range (FSR) is defined by VFS+ = +VREF/GAIN and VFS- = -VREF/GAIN: FSR = VFS+ - VFS- = 2*VREF/GAIN. If VREF is
sourced externally, the analog input range should not exceed 80% of VFS+ or VFS-; that is, VID = 0.8 VFS- to 0.8 VFS+. If VREF is sourced
internally, the given VID ranges apply.
There is no capacitance required on VREF. However, a capacitance of 100 nF is recommended to reduce any reference voltage noise.
Table 5-36. SD24_B Analog Input
CI
mV
fSD24 = 1 MHz
fSD24 = 1 MHz
MAX
UNIT
pF
5
SD24GAINx = 1
3V
200
SD24GAINx = 8
3V
200
SD24GAINx = 32
3V
SD24GAINx = 1
3V
SD24GAINx = 8
3V
SD24GAINx = 32
3V
kΩ
200
300
400
400
300
kΩ
400
All parameters pertain to each SD24_B converter.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
59
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
1600
Input Leakage Current – nA
1400
1200
1000
800
600
400
200
0
-200
-1
-0.5
0
0.5
1
Input Voltage – V
1.5
2
2.5
3
Figure 5-18. Input Leakage Current vs Input Voltage
(Modulator OFF)
Table 5-37. SD24_B Supply Currents
PARAMETER
ISD,256
ISD,512
TEST CONDITIONS
Analog plus digital supply current per
converter (reference not included)
Analog plus digital supply current per
converter (reference not included)
fSD24 = 1 MHz,
SD24OSR = 256
fSD24 = 2 MHz,
SD24OSR = 512
TYP
MAX
SD24GAIN: 1
VCC
3V
MIN
600
675
SD24GAIN: 2
3V
600
675
SD24GAIN: 4
3V
600
675
SD24GAIN: 8
3V
700
750
SD24GAIN: 16
3V
700
750
SD24GAIN: 32
3V
775
850
SD24GAIN: 64
3V
775
850
SD24GAIN: 128
3V
775
850
SD24GAIN: 1
3V
750
800
SD24GAIN: 8
3V
825
900
SD24GAIN: 32
3V
900
1000
UNIT
µA
µA
Table 5-38. SD24_B Performance
fSD24 = 1 MHz, SD24OSRx = 256, SD24REFS = 1
PARAMETER
INL
Gnom
60
Integral nonlinearity, endpoint fit
Nominal gain
Specifications
VCC
MIN
SD24GAIN: 1
TEST CONDITIONS
3V
-0.01
TYP
MAX
0.01
UNIT
SD24GAIN: 8
3V
-0.01
0.01 % of FSR
SD24GAIN: 32
3V
-0.01
0.01
SD24GAIN: 1
3V
1
SD24GAIN: 2
3V
2
SD24GAIN: 4
3V
4
SD24GAIN: 8
3V
8
SD24GAIN: 16
3V
16
SD24GAIN: 32
3V
31.7
SD24GAIN: 64
3V
63.4
SD24GAIN: 128
3V
126.8
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
SD24_B Performance (continued)
fSD24 = 1 MHz, SD24OSRx = 256, SD24REFS = 1
PARAMETER
TEST CONDITIONS
EG
Gain error (1)
ΔEG/ΔT
Gain error temperature
coefficient (2), internal
reference
ΔEG/ΔVC
C
EOS[V]
EOS[FS]
ΔEOS/ΔT
ΔEOS/ΔV
CC
CMRR,D
C
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Gain error vs VCC
(3)
Offset error (4)
Offset error (4)
Offset error temperature
coefficient (5)
Offset error vs VCC
(6)
Common mode rejection at
DC (7)
VCC
MIN
SD24GAIN: 1, with external reference (1.2 V)
3V
-1%
TYP
MAX
+1%
SD24GAIN: 8, with external reference (1.2 V)
3V
-2%
+2%
SD24GAIN: 32, with external reference (1.2 V)
3V
-2%
+2%
SD24GAIN: 1, 8, or 32 (with internal reference)
3V
50
SD24GAIN: 1
0.15
SD24GAIN: 8
0.15
SD24GAIN: 32
0.4
3V
2.3
SD24GAIN: 8
3V
0.73
SD24GAIN: 32
3V
0.18
SD24GAIN: 1 (with Vdiff = 0 V)
3V
-0.2
0.2
SD24GAIN: 8
3V
-0.5
0.5
SD24GAIN: 32
3V
-0.5
0.5
SD24GAIN: 1
3V
1
SD24GAIN: 8
3V
0.15
SD24GAIN: 32
3V
0.1
600
SD24GAIN: 8
100
SD24GAIN: 32
50
SD24GAIN: 1
3V
-110
SD24GAIN: 8
3V
-110
SD24GAIN: 32
3V
-110
ppm/°C
%/V
SD24GAIN: 1 (with Vdiff = 0 V)
SD24GAIN: 1
UNIT
mV
% FS
µV/°C
µV/V
dB
The gain error EG specifies the deviation of the actual gain Gact from the nominal gain Gnom: EG = (Gact - Gnom)/Gnom. It covers process,
temperature and supply voltage variations.
The gain error temperature coefficient ΔEG/ ΔT specifies the variation of the gain error EG over temperature (EG(T) = (Gact(T) Gnom)/Gnom) using the box method (that is, MIN and MAX values):
ΔEG/ ΔT = (MAX(EG(T)) - MIN(EG(T) ) / (MAX(T) - MIN(T)) = (MAX(Gact(T)) - MIN(Gact(T)) / Gnom / (MAX(T) - MIN(T))
with T ranging from -40°C to +85°C.
The gain error vs VCC coefficient ΔEG/ ΔVCC specifies the variation of the gain error EG over supply voltage (EG(VCC) = (Gact(VCC) Gnom)/Gnom) using the box method (that is, MIN and MAX values):
ΔEG/ ΔVCC = (MAX(EG(VCC)) - MIN(EG(VCC) ) / (MAX(VCC) - MIN(VCC)) = (MAX(Gact(VCC)) - MIN(Gact(VCC)) / Gnom / (MAX(VCC) MIN(VCC))
with VCC ranging from 2.4V to 3.6V.
The offset error EOS is measured with shorted inputs in 2s complement mode with +100% FS = VREF/G and -100% FS = -VREF/G.
Conversion between EOS [FS] and EOS [V] is as follows: EOS [FS] = EOS [V]×G/VREF; EOS [V] = EOS [FS]×VREF/G.
The offset error temperature coefficient ΔEOS/ ΔT specifies the variation of the offset error EOS over temperature using the box method
(that is, MIN and MAX values):
ΔEOS/ ΔT = (MAX(EOS(T)) - MIN(EOS(T) ) / (MAX(T) - MIN(T))
with T ranging from -40°C to +85°C.
The offset error vs VCC ΔEOS/ ΔVCC specifies the variation of the offset error EOS over supply voltage using the box method (that is, MIN
and MAX values):
ΔEOS/ ΔVCC = (MAX(EOS(VCC)) - MIN(EOS(VCC) ) / (MAX(VCC) - MIN(VCC))
with VCC ranging from 2.4 V to 3.6 V.
The DC CMRR specifies the change in the measured differential input voltage value when the common mode voltage varies:
DC CMRR = -20log(ΔMAX/FSR) with ΔMAX being the difference between the minium value and the maximum value measured when
sweeping the common mode voltage (for example, calculating with 16-bits FSR = 65536 a maximum change by 1 LSB results in 20log(1/65536) ≈ -96 dB) .
The DC CMRR is measured with both inputs connected to the common mode voltage (that is, no differential input signal is applied), and
the common mode voltage is swept from -1 V to VCC.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
61
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
SD24_B Performance (continued)
fSD24 = 1 MHz, SD24OSRx = 256, SD24REFS = 1
PARAMETER
CMRR,5
0Hz
Common mode rejection at
50 Hz (8)
AC
AC power supply rejection
PSRR,ex
ratio, external reference (9)
t
AC
AC power supply rejection
PSRR,int ratio, internal reference (9)
XT
Crosstalk between
converters (10)
TEST CONDITIONS
VCC
MIN
TYP
SD24GAIN: 1, fCM = 50 Hz, VCM = 930 mV
3V
-110
SD24GAIN: 8, fCM = 50 Hz, VCM = 120 mV
3V
-110
SD24GAIN: 32, fCM = 50 Hz, VCM = 30 mV
3V
-110
SD24GAIN: 1,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-61
SD24GAIN: 8,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-77
SD24GAIN: 32,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-79
SD24GAIN: 1,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-61
SD24GAIN: 8,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-77
SD24GAIN: 32,
VCC = 3 V + 50 mV × sin(2π × fVcc × t),
fVcc = 50 Hz
-79
Crosstalk source: SD24GAIN: 1,
Sine wave with maximum possible Vpp,
fIN = 50 Hz, 100 Hz,
Converter under test: SD24GAIN: 1
3V
-120
Crosstalk source: SD24GAIN: 1,
Sine wave with maximum possible Vpp,
fIN = 50 Hz, 100 Hz,
Converter under test: SD24GAIN: 8
3V
-115
Crosstalk source: SD24GAIN: 1,
Sine wave with maximum possible Vpp,
fIN = 50 Hz, 100 Hz,
Converter under test: SD24GAIN: 32
3V
-100
MAX
UNIT
dB
dB
dB
dB
(8)
The AC CMRR is the difference between a hypothetical signal with the amplitude and frequency of the applied common mode ripple
applied to the inputs of the ADC and the actual common mode signal spur visible in the FFT spectrum:
AC CMRR = Error Spur [dBFS] - 20log(VCM/1.2V/G) [dBFS] with a common mode signal of VCM × sin(2π × fCM × t) applied to the analog
inputs.
The AC CMRR is measured with the both inputs connected to the common mode signal (that is, no differential input signal is applied).
With the specified typical values the error spur is within the noise floor (as specified by the SINAD values).
(9) The AC PSRR is the difference between a hypothetical signal with the amplitude and frequency of the applied supply voltage ripple
applied to the inputs of the ADC and the actual supply ripple spur visible in the FFT spectrum:
AC PSRR = Error Spur [dBFS] - 20log(50 mV / 1.2 V / G) [dBFS] with a signal of 50 mV × sin(2π × fVcc × t) added to VCC.
The AC PSRR is measured with the inputs grounded (that is, no analog input signal is applied).
With the specified typical values the error spur is within the noise floor (as specified by the SINAD values).
SD24GAIN: 1 → Hypothetical signal: 20log(50 mV / 1.2 V / 1) = -27.6 dBFS
SD24GAIN: 8 → Hypothetical signal: 20log(50 mV / 1.2 V / 8) = -9.5 dBFS
SD24GAIN: 32 → Hypothetical signal: 20log(50 mV / 1.2 V / 32) = 2.5 dBFS
(10) The crosstalk (XT) is specified as the tone level of the signal applied to the crosstalk source seen in the spectrum of the converter under
test. It is measured with the inputs of the converter under test being grounded.
62
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 5-39. SD24_B AC Performance
fSD24 = 1MHz, SD24OSRx = 256, SD24REFS = 1
PARAMETER
SINAD
Signal-to-noise + distortion ratio
VCC
MIN
TYP
SD24GAIN: 1
TEST CONDITIONS
3V
85
87
SD24GAIN: 2
3V
SD24GAIN: 4
3V
SD24GAIN: 8
3V
SD24GAIN: 16
fIN = 50 Hz (1)
Total harmonic distortion
3V
84
3V
68
SD24GAIN: 128
3V
62
3V
100
3V
90
3V
80
fIN = 50 Hz (1)
dB
80
3V
SD24GAIN: 32
(1)
85
82
SD24GAIN: 64
SD24GAIN: 8
UNIT
86
SD24GAIN: 32
SD24GAIN: 1
THD
MAX
73
74
dB
The following voltages were applied to the SD24_B inputs:
VI,A+(t) = 0 V + VPP/2 × sin(2π × fIN × t)
VI,A-(t) = 0 V - VPP/2 × sin(2π × fIN × t)
resulting in a differential voltage of VID = VI,A+(t) - VI,A-(t) = VPP × sin(2π × fIN × t) with VPP being selected as the maximum value allowed
for a given range (according to SD24_B recommended operating conditions).
Table 5-40. SD24_B AC Performance
fSD24 = 2MHz, SD24OSRx = 512, SD24REFS = 1
PARAMETER
SINAD
(1)
Signal-to-noise + distortion ratio
TEST CONDITIONS
VCC
MIN
TYP
SD24GAIN: 1
3V
87
SD24GAIN: 2
3V
86
SD24GAIN: 4
3V
85
3V
84
3V
81
SD24GAIN: 32
3V
76
SD24GAIN: 64
3V
71
SD24GAIN: 128
3V
65
SD24GAIN: 8
SD24GAIN: 16
fIN = 50 Hz (1)
MAX
UNIT
dB
The following voltages were applied to the SD24_B inputs:
VI,A+(t) = 0 V + VPP/2 × sin(2π × fIN × t)
VI,A-(t) = 0 V - VPP/2 × sin(2π × fIN × t)
resulting in a differential voltage of VID = VI,A+(t) - VI,A-(t) = VPP × sin(2π × fIN × t) with VPP being selected as the maximum value allowed
for a given range (according to SD24_B recommended operating conditions).
Table 5-41. SD24_B AC Performance
fSD24 = 32 kHz, SD24OSRx = 512, SD24REFS = 1
PARAMETER
SINAD
(1)
Signal-to-noise + distortion ratio
TEST CONDITIONS
VCC
MIN
TYP
SD24GAIN: 1
3V
89
SD24GAIN: 2
3V
85
SD24GAIN: 4
3V
84
SD24GAIN: 8
3V
86
3V
80
SD24GAIN: 32
3V
76
SD24GAIN: 64
3V
67
SD24GAIN: 128
3V
61
SD24GAIN: 16
fIN = 12 Hz (1)
MAX
UNIT
dB
The following voltages were applied to the SD24_B inputs:
VI,A+(t) = 0 V + VPP/2 × sin(2π × fIN × t)
VI,A-(t) = 0 V - VPP/2 × sin(2π × fIN × t)
resulting in a differential voltage of VID = VI,A+(t) - VI,A-(t) = VPP × sin(2π × fIN × t) with VPP being selected as the maximum value allowed
for a given range (according to SD24_B recommended operating conditions).
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
63
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
95
90
SINAD – dB
85
80
75
70
65
60
55
32
64
128
256
512
1024
SD24OSRx
Figure 5-19. SINAD vs OSR
(fSD24 = 1 MHz, SD24REFS = 1, SD24GAIN = 1)
90
85
SINAD – dB
80
75
70
65
60
0.1
0.2
0.3
0.4
0.5
0.6
Vpp/Vref/Gain
0.7
0.8
0.9
1
Figure 5-20. SINAD vs VPP
Table 5-42. SD24_B External Reference Input
ensure correct input voltage range according to VREF
VCC
MIN
TYP
MAX
VREF(I)
Input voltage
PARAMETER
SD24REFS = 0
3V
1.0
1.20
1.5
V
IREF(I)
Input current
SD24REFS = 0
3V
50
nA
64
Specifications
TEST CONDITIONS
UNIT
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
5.7.11 ADC10_A Module
Table 5-43. 10-Bit ADC, Power Supply and Input Range Conditions
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
AVCC
Analog supply voltage
AVCC and DVCC are connected together,
AVSS and DVSS are connected together,
V(AVSS) = V(DVSS) = 0 V
V(Ax)
Analog input voltage range (1)
All ADC10_A pins
Operating supply current into
AVCC terminal, REF module
and reference buffer off
fADC10CLK = 5 MHz, ADC10ON =1, REFON = 0,
SHT0 = 0, SHT1 = 0, ADC10DIV = 0,
ADC10SREF = 00
Operating supply current into
AVCC terminal, REF module
on, reference buffer on
VCC
MIN
TYP
1.8
0
MAX
UNIT
3.6
V
AVCC
V
2.2 V
70
105
3V
80
115
fADC10CLK = 5 MHz, ADC10ON = 1, REFON = 1,
SHT0 = 0, SHT1 = 0, ADC10DIV = 0,
ADC10SREF = 01
3V
130
185
µA
Operating supply current into
AVCC terminal, REF module
off, reference buffer on
fADC10CLK = 5 MHz, ADC10ON = 1, REFON = 0,
SHT0 = 0, SHT1 = 0, ADC10DIV = 0,
ADC10SREF = 10, VEREF = 2.5 V
3V
108
160
µA
Operating supply current into
AVCC terminal, REF module
off, reference buffer off
fADC10CLK = 5 MHz, ADC10ON = 1, REFON = 0,
SHT0 = 0, SHT1 = 0, ADC10DIV = 0,
ADC10SREF = 11, VEREF = 2.5 V
3V
74
105
µA
CI
Input capacitance
Only one terminal Ax can be selected at one time
from the pad to the ADC10_A capacitor array
including wiring and pad.
2.2 V
3.5
RI
Input MUX ON resistance
IADC10_A
(1)
µA
pF
AVCC > 2 V, 0 V ≤ VAx ≤ AVCC
36
1.8 V < AVCC < 2 V, 0 V ≤ VAx ≤ AVCC
96
kΩ
The analog input voltage range must be within the selected reference voltage range VR+ to VR– for valid conversion results. The external
reference voltage requires decoupling capacitors. Two decoupling capacitors, 10 µF and 100 nF, should be connected to VREF to
decouple the dynamic current required for an external reference source if it is used for the ADC10_A. Also see theMSP430x5xx and
MSP430x6xx Family User's Guide (SLAU208).
Table 5-44. 10-Bit ADC, Timing Parameters
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
MIN
TYP
MAX
UNIT
For specified performance of ADC10_A linearity
parameters
2.2 V, 3 V
0.45
5
5.5
MHz
Internal ADC10_A
oscillator (1)
ADC10DIV = 0, fADC10CLK = fADC10OSC
2.2 V, 3 V
4.4
5.0
5.6
MHz
2.2 V, 3 V
2.4
Conversion time
REFON = 0, Internal oscillator, 12 ADC10CLK
cycles, 10-bit mode
fADC10OSC = 4 MHz to 5 MHz
fADC10CLK
fADC10OSC
tCONVERT
TEST CONDITIONS
µs
External fADC10CLK from ACLK, MCLK or SMCLK,
ADC10SSEL ≠ 0
tADC10ON
Turnon settling time of
the ADC
tSample
Sampling time
(1)
(2)
(3)
(4)
See
(2)
(3)
100
RS = 1000 Ω, RI = 96 kΩ, CI = 3.5 pF (4)
RS = 1000 Ω, RI = 36 kΩ, CI = 3.5 pF
3.0
(4)
ns
1.8 V
3
µs
3V
1
µs
The ADC10OSC is sourced directly from MODOSC inside the UCS.
12 × ADC10DIV × 1/fADC10CLK
The condition is that the error in a conversion started after tADC10ON is less than ±0.5 LSB. The reference and input signal are already
settled.
Approximately eight Tau (t) are needed to get an error of less than ±0.5 LSB
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
65
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 5-45. 10-Bit ADC, Linearity Parameters
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
EI
Integral
linearity error
1.4 V ≤ (VeREF+ – VeREF–)min ≤ 1.6 V
ED
Differential
linearity error
(VeREF+ – VeREF–)min ≤ (VeREF+ – VeREF–),
CVeREF+ = 20 pF
2.2 V, 3 V
±1.0
LSB
EO
Offset error
(VeREF+ – VeREF–)min ≤ (VeREF+ – VeREF–),
Internal impedance of source RS < 100 Ω, CVREF+ = 20 pF
2.2 V, 3 V
±1.0
LSB
EG
Gain error
(VeREF+ – VeREF–)min ≤ (VeREF+ – VeREF–),
CVeREF+ = 20 pF, ADC10SREFx = 11b
2.2 V, 3 V
±1.0
LSB
ET
Total unadjusted
error
(VeREF+ – VeREF–)min ≤ (VeREF+ – VeREF–),
CVeREF+ = 20 pF, ADC10SREFx = 11b
2.2 V, 3 V
±2.0
LSB
MAX
UNIT
1.6 V < (VeREF+ – VeREF–)min ≤ VAVCC
±1.0
2.2 V, 3 V
±1.0
±1.0
LSB
Table 5-46. 10-Bit ADC, External Reference
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
VeREF+
Positive external reference
VeREF+ > VeREF–
voltage input
(2)
1.4
AVCC
V
VeREF–
Negative external
reference voltage input
VeREF+ > VeREF–
(3)
0
1.2
V
(VeREF+ –
VeREF–)
Differential external
reference voltage input
VeREF+ > VeREF–
(4)
1.4
AVCC
V
±26
µA
±1
µA
IVeREF+
IVeREF–
Static input current
CVeREF+/(1)
(2)
(3)
(4)
(5)
66
Capacitance at VeREF+
or VeREF- terminal
1.4 V ≤ VeREF+ ≤ VAVCC , VeREF– = 0 V,
fADC10CLK = 5 MHz, ADC10SHTx = 0x0001,
Conversion rate 200 ksps
2.2 V, 3 V
1.4 V ≤ VeREF+ ≤ VAVCC , VeREF– = 0 V,
fADC10CLK = 5 MHz, ADC10SHTX = 0x1000,
Conversion rate 20 ksps
2.2 V, 3 V
See
(5)
±8.5
10
µF
The external reference is used during ADC conversion to charge and discharge the capacitance array. The input capacitance, CI, is also
the dynamic load for an external reference during conversion. The dynamic impedance of the reference supply should follow the
recommendations on analog-source impedance to allow the charge to settle for 10-bit accuracy.
The accuracy limits the minimum positive external reference voltage. Lower reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the maximum negative external reference voltage. Higher reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the minimum external differential reference voltage. Lower differential reference voltage levels may be applied with
reduced accuracy requirements.
Two decoupling capacitors, 10 µF and 100 nF, should be connected to VeREF to decouple the dynamic current required for an external
reference source if it is used for the ADC10_A. Also see the MSP430x5xx and MSP430x6xx Family User's Guide (SLAU208).
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
5.7.12 REF Module
Table 5-47. REF, Built-In Reference
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VREF+
AVCC(min)
Positive built-in reference
voltage
AVCC minimum voltage,
Positive built-in reference
active
VCC
MIN
TYP
MAX
REFVSEL = {2} for 2.5 V, REFON = 1
TEST CONDITIONS
3V
2.47
2.51
2.55
REFVSEL = {1} for 2.0 V, REFON = 1
3V
1.95
1.99
2.03
REFVSEL = {0} for 1.5 V, REFON = 1
2.2 V, 3 V
1.46
1.50
1.54
REFVSEL = {0} for 1.5 V
1.8
REFVSEL = {1} for 2.0 V
2.2
REFVSEL = {2} for 2.5 V
2.7
fADC10CLK = 5 MHz,
REFON = 1, REFBURST = 0,
REFVSEL = {2} for 2.5 V
IREF+
Operating supply current
into AVCC terminal (1)
30
21
27
fADC10CLK = 5 MHz,
REFON = 1, REFBURST = 0,
REFVSEL = {0} for 1.5 V
19
25
10
50
3V
V
V
23
fADC10CLK = 5 MHz,
REFON = 1, REFBURST = 0,
REFVSEL = {1} for 2.0 V
UNIT
µA
TCREF+
Temperature coefficient of
built-in reference (2)
REFVSEL = {0, 1, 2}, REFON = 1
ISENSOR
Operating supply current
into AVCC terminal
REFON = 1, ADC10ON = 1,
INCH = 0Ah, TA = 30°C
2.2 V
145
220
3V
170
245
VSENSOR
See
REFON = 1, ADC10ON = 1,
INCH = 0Ah, TA = 30°C
2.2 V
780
3V
780
VMID
AVCC divider at channel 11
ADC10ON = 1, INCH = 0Bh,
VMID is ~0.5 × VAVCC
2.2 V
1.08
1.1
1.12
3V
1.48
1.5
1.52
tSENSOR(sample)
Sample time required if
channel 10 is selected (4)
REFON = 1, ADC10ON = 1, INCH = 0Ah,
Error of conversion result ≤ 1 LSB
tVMID(sample)
Sample time required if
channel 11 is selected (5)
ADC10ON = 1, INCH = 0Bh,
Error of conversion result ≤ 1 LSB
PSRR_DC
Power supply rejection ratio
(dc)
AVCC = AVCC (min) - AVCC(max)
TA = 25°C,
REFVSEL = {0, 1, 2}, REFON = 1
PSRR_AC
Power supply rejection ratio
(ac)
AVCC = AVCC (min) - AVCC(max)
TA = 25°C, f = 1 kHz, ΔVpp = 100 mV,
REFVSEL = {0, 1, 2}, REFON = 1
1
mV/V
tSETTLE
Settling time of reference
voltage (6)
AVCC = AVCC (min) - AVCC(max)
REFVSEL = {0, 1, 2}, REFON = 0 → 1
75
µs
VSD24REF
SD24_B internal reference
voltage
SD24REFS = 1
3V
tON
SD24_B internal reference
turnon time (7)
SD24REFS = 0→1, CREF = 100 nF
3V
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(3)
ppm/
°C
µA
mV
V
30
µs
1
µs
120
1.137
1.151
300
1.165
200
µV/V
V
µs
The internal reference current is supplied by terminal AVCC. Consumption is independent of the ADC10ON control bit, unless a
conversion is active. The REFON bit enables to settle the built-in reference before starting an A/D conversion.
Calculated using the box method: (MAX(–40°C to 85°C) – MIN(–40°C to 85°C)) / MIN(–40°C to 85°C)/(85°C – (–40°C)).
The temperature sensor offset can be as much as ±20°C. A single-point calibration is recommended to minimize the offset error of the
built-in temperature sensor.
The typical equivalent impedance of the sensor is 51 kΩ. The sample time required includes the sensor-on time tSENSOR(on).
The on-time tVMID(on) is included in the sampling time tVMID(sample); no additional on time is needed.
The condition is that the error in a conversion started after tREFON is ≤ 1 LSB.
The condition is that SD24_B conversion started after tON should ensure specified SINAD values for the selected Gain, OSR, and fSD24.
Specifications
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
67
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
5.7.13 Flash
Table 5-48. Flash Memory
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TEST
CONDITIONS
PARAMETER
MIN
DVCC(PGM/ERASE) Program and erase supply voltage
TYP
1.8
MAX
3.6
UNIT
V
IPGM
Average supply current from DVCC during program
3
5
mA
IERASE
Average supply current from DVCC during erase
6
11
mA
IMERASE, IBANK
Average supply current from DVCC during mass erase or bank
erase
6
11
mA
tCPT
Cumulative program time
See
(1)
16
104
Program and erase endurance
tRetention
Data retention duration
TJ = 25°C
105
ms
cycles
100
years
Word or byte program time
See
(2)
64
85
µs
0
Block program time for first byte or word
See
(2)
49
65
µs
tBlock,
1–(N–1)
Block program time for each additional byte or word, except for last
byte or word
See
(2)
37
49
µs
tBlock,
N
Block program time for last byte or word
See
(2)
55
73
µs
See
(2)
23
32
ms
0
1
MHz
tWord
tBlock,
tErase
Erase time for segment erase, mass erase, and bank erase when
available
fMCLK,MGR
MCLK frequency in marginal read mode
(FCTL4.MGR0 = 1 or FCTL4. MGR1 = 1)
(1)
(2)
The cumulative program time must not be exceeded when writing to a 128-byte flash block. This parameter applies to all programming
methods: individual word- or byte-write and block-write modes.
These values are hardwired into the flash controller state machine.
5.7.14 Emulation and Debug
5.7.14.1 Emulation and Debug
Table 5-49. JTAG and Spy-Bi-Wire Interface
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST
CONDITIONS
MIN
TYP
MAX
UNIT
fSBW
Spy-Bi-Wire input frequency
2.2 V, 3 V
0
20
MHz
tSBW,Low
Spy-Bi-Wire low clock pulse duration
2.2 V, 3 V
0.025
15
µs
tSBW, En
Spy-Bi-Wire enable time (TEST high to acceptance of first clock
edge) (1)
2.2 V, 3 V
1
µs
tSBW,Rst
Spy-Bi-Wire return to normal operation time
µs
fTCK
TCK input frequency for 4-wire JTAG (2)
Rinternal
Internal pulldown resistance on TEST
(1)
(2)
68
15
100
2.2 V
0
5
3V
0
10
2.2 V, 3 V
45
60
80
MHz
kΩ
Tools accessing the Spy-Bi-Wire interface need to wait for the minimum tSBW,En time after pulling the TEST/SBWTCK pin high before
applying the first SBWTCK clock edge.
fTCK may be restricted to meet the timing requirements of the module selected.
Specifications
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6 Detailed Description
6.1
Overview
The MSP430F673xA and MSP430F673xA devices are microcontrollers with three high-performance 24-bit
sigma-delta ADCs, a 10-bit ADC, four enhanced universal serial communication interfaces (three
eUSCI_A modules and one eUSCI_B module), four 16-bit timers, a hardware multiplier, a DMA module, a
real-time clock module with alarm capabilities, an LCD driver with integrated contrast control, an auxiliary
supply system, and up to 72 I/O pins in the 100-pin devices and 52 I/O pins in the 80-pin devices.
6.2
CPU
The MSP430 CPU has a 16-bit RISC architecture that is highly transparent to the application. All
operations, other than program-flow instructions, are performed as register operations in conjunction with
seven addressing modes for source operand and four addressing modes for destination operand.
The CPU is integrated with 16 registers that provide reduced instruction execution time. The register-toregister operation execution time is one cycle of the CPU clock.
Four of the registers, R0 to R3, are dedicated as program counter, stack pointer, status register, and
constant generator, respectively. The remaining registers are general-purpose registers.
Peripherals are connected to the CPU using data, address, and control buses, and can be handled with all
instructions.
Program Counter
PC/R0
Stack Pointer
SP/R1
Status Register
Constant Generator
SR/CG1/R2
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
General-Purpose Register
R11
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
69
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
6.3
www.ti.com
Instruction Set
The instruction set consists of the original 51 instructions with three formats and seven address modes
and additional instructions for the expanded address range. Each instruction can operate on word and
byte data. Table 6-1 shows examples of the three types of instruction formats; Table 6-2 shows the
address modes.
Table 6-1. Instruction Word Formats
INSTRUCTION WORD FORMAT
EXAMPLE
Dual operands, source-destination
ADD
R4,R5
Single operands, destination only
CALL
Relative jump, un/conditional
JNE
R8
OPERATION
R4 + R5 → R5
PC → (TOS), R8 → PC
Jump-on-equal bit = 0
Table 6-2. Address Mode Descriptions
ADDRESS MODE
S (1)
D (1)
SYNTAX
EXAMPLE
Register
+
+
MOV Rs,Rd
MOV R10,R11
R10 → R11
Indexed
+
+
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
M(2+R5) → M(6+R6)
Symbolic (PC relative)
+
+
MOV EDE,TONI
Absolute
+
+
MOV & MEM, & TCDAT
Indirect
+
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) → M(Tab+R6)
Indirect autoincrement
+
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) → R11
R10 + 2 → R10
Immediate
+
MOV #X,TONI
MOV #45,TONI
#45 → M(TONI)
(1)
S = source, D = destination
70
Detailed Description
OPERATION
M(EDE) → M(TONI)
M(MEM) → M(TCDAT)
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
6.4
SLASE46 – FEBRUARY 2015
Operating Modes
The MSP430 has one active mode and seven software selectable low-power modes of operation. An
interrupt event can wake up the device from any of the low-power modes, service the request, and restore
back to the low-power mode on return from the interrupt program.
The following seven operating modes can be configured by software:
• Active mode (AM)
– All clocks are active
• Low-power mode 0 (LPM0)
– CPU is disabled
– ACLK and SMCLK remain active, MCLK is disabled
– FLL loop control remains active
• Low-power mode 1 (LPM1)
– CPU is disabled
– FLL loop control is disabled
– ACLK and SMCLK remain active, MCLK is disabled
• Low-power mode 2 (LPM2)
– CPU is disabled
– MCLK and FLL loop control and DCOCLK are disabled
– DCO dc generator remains enabled
– ACLK remains active
• Low-power mode 3 (LPM3)
– CPU is disabled
– MCLK, FLL loop control, and DCOCLK are disabled
– DCO dc generator is disabled
– ACLK remains active
• Low-power mode 4 (LPM4)
– CPU is disabled
– ACLK is disabled
– MCLK, FLL loop control, and DCOCLK are disabled
– DCO dc generator is disabled
– Crystal oscillator is stopped
– Complete data retention
• Low-power mode 3.5 (LPM3.5)
– Internal regulator disabled
– No RAM retention, Backup RAM retained
– I/O pad state retention
– RTC clocked by low-frequency oscillator
– Wakeup from RST/NMI, RTC_C events, Ports P1 and P2
• Low-power mode 4.5 (LPM4.5)
– Internal regulator disabled
– No RAM retention, Backup RAM retained
– RTC is disabled
– I/O pad state retention
– Wakeup from RST/NMI, Ports P1 and P2
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
71
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
6.5
www.ti.com
Interrupt Vector Addresses
The interrupt vectors and the power-up start address are located in the address range 0FFFFh to 0FF80h.
The vector contains the 16-bit address of the appropriate interrupt-handler instruction sequence.
Table 6-3. Interrupt Sources, Flags, and Vectors
INTERRUPT SOURCE
System Reset
Power-Up
External Reset
Watchdog Timeout, Key Violation
Flash Memory Key Violation
INTERRUPT FLAG
WDTIFG, KEYV (SYSRSTIV) (1)
(2)
SYSTEM
INTERRUPT
WORD
ADDRESS
PRIORITY
Reset
0FFFEh
63, highest
System NMI
PMM
Vacant Memory Access
JTAG Mailbox
SVMLIFG, SVMHIFG, DLYLIFG, DLYHIFG,
VLRLIFG, VLRHIFG, VMAIFG, JMBNIFG,
JMBOUTIFG (SYSSNIV) (1) (3)
(Non)maskable
0FFFCh
62
User NMI
NMI
Oscillator Fault
Flash Memory Access Violation
Supply Switch
NMIIFG, OFIFG, ACCVIFG, AUXSWNMIFG
(SYSUNIV) (1) (3)
(Non)maskable
0FFFAh
61
Watchdog Timer_A Interval Timer
Mode
WDTIFG
Maskable
0FFF8h
60
(4)
Maskable
0FFF6h
59
(1) (4)
Maskable
0FFF4h
58
Maskable
0FFF2h
57
Maskable
0FFF0h
56
Maskable
0FFEEh
55
Maskable
0FFECh
54
Maskable
0FFEAh
53
Maskable
0FFE8h
52
Maskable
0FFE6h
51
Maskable
0FFE4h
50
Maskable
0FFE2h
49
Maskable
0FFE0h
48
Maskable
0FFDEh
47
Maskable
0FFDCh
46
Maskable
0FFDAh
45
eUSCI_A0 Receive or Transmit
eUSCI_B0 Receive or Transmit
ADC10_A
SD24_B
Timer TA0
Timer TA0
UCA0RXIFG, UCA0TXIFG (UCA0IV) (1)
UCB0RXIFG, UCB0TXIFG (UCB0IV)
ADC10IFG0, ADC10INIFG, ADC10LOIFG,
ADC10HIIFG, ADC10TOVIFG, ADC10OVIFG
(ADC10IV) (1) (4)
SD24_B Interrupt Flags (SD24IV) (1)
TA0CCR0 CCIFG0
(4)
(4)
TA0CCR1 CCIFG1, TA0CCR2 CCIFG2,
TA0IFG (TA0IV) (1) (4)
(1) (4)
eUSCI_A1 Receive or Transmit
UCA1RXIFG, UCA1TXIFG (UCA1IV)
eUSCI_A2 Receive or Transmit
UCA2RXIFG, UCA2TXIFG (UCA2IV) (1)
Auxiliary Supplies
DMA
(1)
(2)
(3)
(4)
72
Auxiliary Supplies Interrupt Flags (AUXIV)
(4)
(1) (4)
DMA0IFG, DMA1IFG, DMA2IFG (DMAIV) (1)
Timer TA1
TA1CCR0 CCIFG0 (4)
Timer TA1
TA1CCR1 CCIFG1,
TA1IFG (TA1IV) (1) (4)
I/O Port P1
P1IFG.0 to P1IFG.7 (P1IV)
Timer TA2
TA2CCR0 CCIFG0 (4)
Timer TA2
TA2CCR1 CCIFG1,
TA2IFG (TA2IV) (1) (4)
(4)
(1) (4)
(1) (4)
I/O Port P2
P2IFG.0 to P2IFG.7 (P2IV)
Maskable
0FFD8h
44
Timer TA3
TA3CCR0 CCIFG0
(4)
Maskable
0FFD6h
43
Timer TA3
TA3CCR1 CCIFG1,
TA3IFG (TA3IV) (1) (4)
Maskable
0FFD4h
42
Maskable
0FFD2h
41
Maskable
0FFD0h
40
LCD_C
LCD_C Interrupt Flags (LCDCIV) (1)
(4)
RTC_C
RTCOFIFG, RTCRDYIFG, RTCTEVIFG,
RTCAIFG, RT0PSIFG, RT1PSIFG (RTCIV) (1)
(4)
Multiple source flags
A reset is generated if the CPU tries to fetch instructions from within peripheral space or vacant memory space.
(Non)maskable: the individual interrupt-enable bit can disable an interrupt event, but the general-interrupt enable cannot disable it.
Interrupt flags are located in the module.
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-3. Interrupt Sources, Flags, and Vectors (continued)
(5)
INTERRUPT SOURCE
INTERRUPT FLAG
Reserved
Reserved (5)
SYSTEM
INTERRUPT
WORD
ADDRESS
PRIORITY
0FFCEh
39
⋮
⋮
0FF80h
0, lowest
Reserved interrupt vectors at addresses are not used in this device and can be used for regular program code if necessary. To maintain
compatibility with other devices, TI recommends reserving these locations.
6.6
Bootstrap Loader (BSL)
The BSL enables users to program the flash memory or RAM using various serial interfaces. Access to
the device memory via the BSL is protected by an user-defined password. BSL entry requires a specific
entry sequence on the RST/NMI/SBWTDIO and TEST/SBWTCK pins. For complete description of the
features of the BSL and its implementation, seeMSP430 Programming via the Bootstrap Loader (BSL)
(SLAU319).
Table 6-4. UART BSL Pin Requirements and Functions
6.7
6.7.1
DEVICE SIGNAL
BSL FUNCTION
RST/NMI/SBWTDIO
Entry sequence signal
TEST/SBWTCK
Entry sequence signal
P3.0
Data transmit
P3.1
Data receive
VCC
Power supply
VSS
Ground supply
JTAG Operation
JTAG Standard Interface
The MSP430 family supports the standard JTAG interface which requires four signals for sending and
receiving data. The JTAG signals are shared with general-purpose I/O. The TEST/SBWTCK pin is used to
enable the JTAG signals. In addition to these signals, theRST/NMI/SBWTDIO is required to interface with
MSP430 development tools and device programmers. The JTAG pin requirements are shown in Table 65. For further details on interfacing to development tools and device programmers, see the MSP430
Hardware Tools User's Guide (SLAU278) and MSP430 Programming Via the JTAG Interface (SLAU320).
Table 6-5. JTAG Pin Requirements and Functions
DEVICE SIGNAL
DIRECTION
FUNCTION
PJ.3/ACLK/TCK
IN
JTAG clock input
PJ.2/ADC10CLK/TMS
IN
JTAG state control
PJ.1/MCLK/TDI/TCLK
IN
JTAG data input/TCLK input
PJ.0/SMCLK/TDO
OUT
JTAG data output
TEST/SBWTCK
IN
Enable JTAG pins
RST/NMI/SBWTDIO
IN
External reset
VCC
Power supply
VSS
Ground supply
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
73
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
6.7.2
www.ti.com
Spy-Bi-Wire Interface
In addition to the standard JTAG interface, the MSP430 family supports the two-wire Spy-Bi-Wire
interface. Spy-Bi-Wire can be used to interface with MSP430 development tools and device programmers.
The Spy-Bi-Wire interface pin requirements are shown in Table 6-6. For further details on interfacing to
development tools and device programmers, see the MSP430 Hardware Tools User's Guide (SLAU278)
and MSP430 Programming Via the JTAG Interface (SLAU320).
Table 6-6. Spy-Bi-Wire Pin Requirements and Functions
6.8
DEVICE SIGNAL
DIRECTION
FUNCTION
TEST/SBWTCK
IN
Spy-Bi-Wire clock input
RST/NMI/SBWTDIO
IN, OUT
Spy-Bi-Wire data input/output
VCC
Power supply
VSS
Ground supply
Flash Memory
The flash memory can be programmed via the JTAG port, Spy-Bi-Wire (SBW), the BSL, or in-system by
the CPU. The CPU can perform single-byte, single-word, and long-word writes to the flash memory.
Features of the flash memory include:
• Flash memory has n segments of main memory and four segments of information memory (A to D) of
128 bytes each. Each segment in main memory is 512 bytes in size.
• Segments 0 to n may be erased in one step, or each segment may be individually erased.
• Segments A to D can be erased individually, or as a group with segments 0 to n. Segments A to D are
also called information memory.
• Segment A can be locked separately.
6.9
RAM
The RAM is made up of n sectors. Each sector can be completely powered down to save leakage,
however all data is lost. Features of the RAM include:
• RAM has n sectors of 2k bytes each.
• Each sector 0 to n can be complete disabled; however, data retention is lost.
• Each sector 0 to n automatically enters low-power retention mode when possible.
6.10 Backup RAM
The backup RAM provides a limited number of bytes of RAM that are retained during LPMx.5. This
Backup RAM is part of the Backup subsystem that operates on dedicated power supply AUXVCC3.There
are 8 bytes of Backup RAM available in this device. It can be word-wise accessed through the registers
BAKMEM0, BAKMEM1, BAKMEM2, and BAKMEM3. The Backup RAM registers can not be accessed by
the CPU when the high-side SVS is disabled by user.
74
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11 Peripherals
Peripherals are connected to the CPU through data, address, and control buses. The peripherals can be
handled using all instructions. For complete module descriptions, see theMSP430x5xx and MSP430x6xx
Family User's Guide (SLAU208).
6.11.1 Oscillator and System Clock
The Unified Clock System (UCS) module includes support for a 32768-Hz watch crystal oscillator, an
internal very-low-power low-frequency oscillator (VLO), an internal trimmed low-frequency oscillator
(REFO), and an integrated internal digitally-controlled oscillator (DCO). The UCS module is designed to
meet the requirements of both low system cost and low power consumption. The UCS module features
digital frequency-locked loop (FLL) hardware that, in conjunction with a digital modulator, stabilizes the
DCO frequency to a programmable multiple of the selected FLL reference frequency. The internal DCO
provides a fast turn-on clock source and stabilizes in 3 µs (typical). The UCS module provides the
following clock signals:
• Auxiliary clock (ACLK), sourced from a 32768-Hz watch crystal, the internal low-frequency oscillator
(VLO), or the trimmed low-frequency oscillator (REFO).
• Main clock (MCLK), the system clock used by the CPU. MCLK can be sourced by same sources made
available to ACLK.
• Sub-Main clock (SMCLK), the subsystem clock used by the peripheral modules. SMCLK can be
sourced by same sources made available to ACLK.
• ACLK/n, the buffered output of ACLK, ACLK/2, ACLK/4, ACLK/8, ACLK/16, ACLK/32.
6.11.2 Power-Management Module (PMM)
The PMM includes an integrated voltage regulator that supplies the core voltage to the device and
contains programmable output levels to provide for power optimization. The PMM also includes supply
voltage supervisor (SVS) and supply voltage monitoring (SVM) circuitry, as well as brownout protection.
The brownout circuit is implemented to provide the proper internal reset signal to the device during poweron and power-off. The SVS/SVM circuitry detects if the supply voltage drops below a user-selectable level
and supports both supply voltage supervision (the device is automatically reset) and supply voltage
monitoring (the device is not automatically reset). SVS and SVM circuitry is available on the primary
supply and core supply.
6.11.3 Auxiliary Supply System
The auxiliary supply system provides the possibility to operate the device from auxiliary supplies when the
primary supply fails.There are two auxililary supplies (AUXVCC1 and AUXVCC2) are supported. This
module supports automatic and manual switching from primary supply to auxiliary suppllies while
maintaining full functionality. It allows threshold based monitoring of primary and auxiliary supplies. The
device can be started from primary supply or AUXVCC1, whichever is higher. Auxiliary supply system
enables internal monitoring of voltage levels on primary and auxiliary supplies using ADC10_A. Also this
module implements simple charger for backup supplies.
6.11.4 Backup Subsystem
The Backup subsystem operates on a dedicated power supply AUXVCC3. This subsystem includes lowfrequency oscillator (XT1), Real-Time Clock module, and Backup RAM. The functionality of Backup
subsystem is retained during LPM3.5. The Backup subsystem module registers can not be accessed by
CPU when the high side SVS is disabled by user. It is necessary to keep the high-side SVS enabled with
SVSHMD = 1 and SVSMHACE = 0 to turn off the low-frequency oscillator (XT1) in LPM4.
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
75
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.5 Digital I/O
There are up to nine 8-bit I/O ports implemented. For 100 pin options, Ports P1 to P8 are complete. P9 is
reduced to 4-bit I/O. For 80 pin options, Ports P1 to P6 are complete. P7, P8 and P9 are completely
removed. Port PJ contains four individual I/O pins, common to all devices. All I/O bits are individually
programmable.
• Any combination of input, output and interrupt conditions is possible.
• Pullup or pulldown on all ports is programmable.
• Programmable drive strength on all ports.
• Edge-selectable interrupt and LPM3.5, LPM4.5 wakeup input capability available for all bits of ports P1
and P2.
• Read and write access to port-control registers is supported by all instructions.
• Ports can be accessed byte-wise (P1 through P9) or word-wise in pairs (PA through PE).
6.11.6 Port Mapping Controller
The port mapping controller allows flexible and reconfigurable mapping of digital functions to P1, P2, and
P3.
Table 6-7. Port Mapping Mnemonics and Functions
VALUE
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
0
PM_NONE
None
DVSS
1
2
3
4
5
6
eUSCI_A0 UART RXD (direction controlled by eUSCI – Input)
PM_UCA0SOMI
eUSCI_A0 SPI slave out master in (direction controlled by eUSCI)
PM_UCA0TXD
eUSCI_A0 UART TXD (direction controlled by eUSCI – Output)
PM_UCA0SIMO
eUSCI_A0 SPI slave in master out (direction controlled by eUSCI)
PM_UCA0CLK
eUSCI_A0 clock input/output (direction controlled by eUSCI)
PM_UCA0STE
eUSCI_A0 SPI slave transmit enable (direction controlled by eUSCI)
PM_UCA1RXD
eUSCI_A1 UART RXD (direction controlled by eUSCI – Input)
PM_UCA1SOMI
eUSCI_A1 SPI slave out master in (direction controlled by eUSCI)
PM_UCA1TXD
eUSCI_A1 UART TXD (direction controlled by eUSCI – Output)
PM_UCA1SIMO
eUSCI_A1 SPI slave in master out (direction controlled by eUSCI)
7
PM_UCA1CLK
eUSCI_A1 clock input/output (direction controlled by eUSCI)
8
PM_UCA1STE
eUSCI_A1 SPI slave transmit enable (direction controlled by eUSCI)
9
10
PM_UCA2RXD
eUSCI_A2 UART RXD (direction controlled by eUSCI – Input)
PM_UCA2SOMI
eUSCI_A2 SPI slave out master in (direction controlled by eUSCI)
PM_UCA2TXD
eUSCI_A2 UART TXD (direction controlled by eUSCI – Output)
PM_ UCA2SIMO
eUSCI_A2 SPI slave in master out (direction controlled by eUSCI)
11
PM_UCA2CLK
eUSCI_A2 clock input/output (direction controlled by eUSCI)
12
PM_UCA2STE
eUSCI_A2 SPI slave transmit enable (direction controlled by eUSCI)
13
14
76
PM_UCA0RXD
PM_UCB0SIMO
eUSCI_B0 SPI slave in master out (direction controlled by eUSCI)
PM_UCB0SDA
eUSCI_B0 I2C data (open drain and direction controlled by eUSCI)
PM_UCB0SOMI
eUSCI_B0 SPI slave out master in (direction controlled by eUSCI)
PM_UCB0SCL
eUSCI_B0 I2C clock (open drain and direction controlled by eUSCI)
15
PM_UCB0CLK
eUSCI_B0 clock input/output (direction controlled by eUSCI)
16
PM_UCB0STE
eUSCI_B0 SPI slave transmit enable (direction controlled by eUSCI)
17
PM_TA0.0
TA0 CCR0 capture input CCI0A
TA0 CCR0 compare output Out0
18
PM_TA0.1
TA0 CCR1 capture input CCI1A
TA0 CCR1 compare output Out1
19
PM_TA0.2
TA0 CCR2 capture input CCI2A
TA0 CCR2 compare output Out2
20
PM_TA1.0
TA1 CCR0 capture input CCI0A
TA1 CCR0 compare output Out0
21
PM_TA1.1
TA1 CCR1 capture input CCI1A
TA1 CCR1 compare output Out1
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-7. Port Mapping Mnemonics and Functions (continued)
VALUE
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
22
PM_TA2.0
TA2 CCR0 capture input CCI0A
TA2 CCR0 compare output Out0
23
PM_TA2.1
TA2 CCR1 capture input CCI1A
TA2 CCR1 compare output Out1
24
PM_TA3.0
TA3 CCR0 capture input CCI0A
TA3 CCR0 compare output Out0
25
PM_TA3.1
TA3 CCR1 capture input CCI1A
TA3 CCR1 compare output Out1
PM_TACLK
Timer_A clock input to
TA0, TA1, TA2, TA3
None
None
RTC_C clock output
26
PM_RTCCLK
27
PM_SDCLK
SD24_B bit stream clock input/output (direction controlled by SD24_B)
28
PM_SD0DIO
SD24_B converter 0 bit stream data input/output (direction controlled by SD24_B)
29
PM_SD1DIO
SD24_B converter 1 bit stream data input/output (direction controlled by SD24_B)
30
PM_SD2DIO
SD24_B converter 2 bit stream data input/output (direction controlled by SD24_B)
PM_ANALOG
Disables the output driver and the input Schmitt-trigger to prevent parasitic cross currents
when applying analog signals.
31(0FFh)
(1)
(1)
The value of the PM_ANALOG mnemonic is set to 0FFh. The port mapping registers are only 5 bits wide, and the upper bits are
ignored, which results in a read out value of 31.
Table 6-8. Default Mapping
PIN NAME
PZ
PN
PxMAPy MNEMONIC
INPUT PIN FUNCTION
OUTPUT PIN FUNCTION
P1.0/PM_TA0.0/
VeREF-/A2
P1.0/PM_TA0.0/
VeREF-/A2
PM_TA0.0
TA0 CCR0 capture input CCI0A
TA0 CCR0 compare output Out0
P1.1/PM_TA0.1/
VeREF+/A1
P1.1/PM_TA0.1/
VeREF+/A1
PM_TA0.1
TA0 CCR1 capture input CCI1A
TA0 CCR1 compare output Out1
P1.2/PM_UCA0RXD/
PM_UCA0SOMI/A0
P1.2/PM_UCA0RXD/
PM_UCA0SOMI/A0
PM_UCA0RXD,
PM_UCA0SOMI
eUSCI_A0 UART RXD
(direction controlled by eUSCI – input),
eUSCI_A0 SPI slave out master in
(direction controlled by eUSCI)
P1.3/PM_UCA0TXD/
PM_UCA0SIMO/R03
P1.3/PM_UCA0TXD/
PM_UCA0SIMO/R03
PM_UCA0TXD,
PM_UCA0SIMO
eUSCI_A0 UART TXD
(direction controlled by eUSCI – output),
eUSCI_A0 SPI slave in master out
(direction controlled by eUSCI)
P1.4/PM_UCA1RXD/
PM_UCA1SOMI/
LCDREF/R13
P1.4/PM_UCA1RXD/
PM_UCA1SOMI/
LCDREF/R13
PM_UCA1RXD,
PM_UCA1SOMI
eUSCI_A1 UART RXD
(direction controlled by eUSCI – input),
eUSCI_A1 SPI slave out master in
(direction controlled by eUSCI)
P1.5/PM_UCA1TXD/
PM_UCA1SIMO/R23
P1.5/PM_UCA1TXD/
PM_UCA1SIMO/R23
PM_UCA1TXD,
PM_UCA1SIMO
eUSCI_A1 UART TXD
(direction controlled by eUSCI – output),
eUSCI_A1 SPI slave in master out
(direction controlled by eUSCI)
P1.6/PM_UCA0CLK/
COM4
P1.6/PM_UCA0CLK/
COM4
PM_UCA0CLK
eUSCI_A0 clock input/output (direction controlled by eUSCI)
P1.7/PM_UCB0CLK/
COM5
P1.7/PM_UCB0CLK/
COM5
PM_UCB0CLK
eUSCI_B0 clock input/output (direction controlled by eUSCI)
P2.0/PM_UCB0SOMI/
PM_UCB0SCL/COM6
P2.0/PM_UCB0SOMI/
PM_UCB0SCL/COM6/S39
PM_UCB0SOMI,
PM_UCB0SCL
eUSCI_B0 SPI slave out master in
(direction controlled by eUSCI),
eUSCI_B0 I2C clock
(open drain and direction controlled by eUSCI)
P2.1/PM_UCB0SIMO/
PM_UCB0SDA/COM7
P2.1/PM_UCB0SIMO/
PM_UCB0SDA/COM7/S38
PM_UCB0SIMO,
PM_UCB0SDA
eUSCI_B0 SPI slave in master out
(direction controlled by eUSCI),
eUSCI_B0 I2C data
(open drain and direction controlled by eUSCI)
P2.2/PM_UCA2RXD/
PM_UCA2SOMI
P2.2/PM_UCA2RXD/
PM_UCA2SOMI/S37
PM_UCA2RXD,
PM_UCA2SOMI
eUSCI_A2 UART RXD
(direction controlled by eUSCI – input),
eUSCI_A2 SPI slave out master in
(direction controlled by eUSCI)
P2.3/PM_UCA2TXD/
PM_UCA2SIMO
P2.3/PM_UCA2TXD/
PM_UCA2SIMO/S36
PM_UCA2TXD,
PM_UCA2SIMO
eUSCI_A2 UART TXD
(direction controlled by eUSCI – output),
eUSCI_A2 SPI slave in master out
(direction controlled by eUSCI)
P2.4/PM_UCA1CLK
P2.4/PM_UCA1CLK/S35
PM_UCA1CLK
eUSCI_A1 clock input/output (direction controlled by eUSCI)
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
77
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-8. Default Mapping (continued)
PIN NAME
PZ
PN
PxMAPy MNEMONIC
INPUT PIN FUNCTION
PM_UCA2CLK
OUTPUT PIN FUNCTION
P2.5/PM_UCA2CLK
P2.5/PM_UCA2CLK/S34
P2.6/PM_TA1.0
P2.6/PM_TA1.0/S33
PM_TA1.0
TA1 CCR0 capture input CCI0A
eUSCI_A2 clock input/output (direction controlled by eUSCI)
TA1 CCR0 compare output Out0
P2.7/PM_TA1.1
P2.7/PM_TA1.1/S32
PM_TA1.1
TA1 CCR1 capture input CCI1A
TA1 CCR1 compare output Out1
P3.0/PM_TA2.0
P3.0/PM_TA2.0/S31
PM_TA2.0
TA2 CCR0 capture input CCI0A
TA2 CCR0 compare output Out0
P3.1/PM_TA2.1
P3.1/PM_TA2.1/S30
PM_TA2.1
TA2 CCR1 capture input CCI1A
TA2 CCR1 compare output Out1
P3.2/PM_TACLK/
PM_RTCCLK
P3.2/PM_TACLK/
PM_RTCCLK/S29
PM_TACLK,
PM_RTCCLK
Timer_A clock input to
TA0, TA1, TA2, TA3
RTC_C clock output
P3.3/PM_TA0.2
P3.3/PM_TA0.2/S28
PM_TA0.2
TA0 CCR2 capture input CCI2A
TA0 CCR2 compare output Out2
P3.4/PM_SDCLK/S39
P3.4/PM_SDCLK/S27
PM_SDCLK
SD24_B bit stream clock input/output
(direction controlled by SD24_B)
P3.5/PM_SD0DIO/S38
P3.5/PM_SD0DIO/S26
PM_SD0DIO
SD24_B converter 0 bit stream data input/output
(direction controlled by SD24_B)
P3.6/PM_SD1DIO/S37
P3.6/PM_SD1DIO/S25
PM_SD1DIO
SD24_B converter 1 bit stream data input/output
(direction controlled by SD24_B)
P3.7/PM_SD2DIO/S36
P3.7/PM_SD2DIO/S24
PM_SD2DIO
SD24_B converter 2 bit stream data input/output
(direction controlled by SD24_B)
6.11.7 System Module (SYS)
The SYS module handles many of the system functions within the device. These include power on reset
(POR) and power up clear (PUC) handling, NMI source selection and management, reset interrupt vector
generators, boot strap loader entry mechanisms, as well as, configuration management (device
descriptors). It also includes a data exchange mechanism via JTAG called a JTAG mailbox that can be
used in the application.
Table 6-9. System Module Interrupt Vector Registers
INTERRUPT VECTOR REGISTER
SYSRSTIV, System Reset
78
Detailed Description
INTERRUPT EVENT
WORD
ADDRESS
OFFSET
No interrupt pending
00h
Brownout (BOR)
02h
RST/NMI (POR)
04h
DoBOR (BOR)
06h
Wakeup from LPMx.5 (BOR)
08h
Security violation (BOR)
0Ah
SVSL (POR)
0Ch
SVSH (POR)
0Eh
SVML_OVP (POR)
SVMH_OVP (POR)
019Eh
PRIORITY
Highest
10h
12h
DoPOR (POR)
14h
WDT timeout (PUC)
16h
WDT key violation (PUC)
18h
KEYV flash key violation (PUC)
1Ah
Reserved
1Ch
Peripheral area fetch (PUC)
1Eh
PMM key violation (PUC)
20h
Reserved
22h to 3Eh
Lowest
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-9. System Module Interrupt Vector Registers (continued)
INTERRUPT VECTOR REGISTER
INTERRUPT EVENT
WORD
ADDRESS
OFFSET
No interrupt pending
00h
SVMLIFG
02h
SVMHIFG
04h
DLYLIFG
06h
DLYHIFG
SYSSNIV, System NMI
Highest
08h
VMAIFG
019Ch
0Ah
JMBINIFG
0Ch
JMBOUTIFG
0Eh
VLRLIFG
10h
VLRHIFG
12h
Reserved
14h to 1Eh
No interrupt pending
00h
NMIFG
02h
OFIFG
SYSUNIV, User NMI
PRIORITY
019Ah
ACCVIFG
Lowest
Highest
04h
06h
AUXSWNMIFG
08h
Reserved
0Ah to 1Eh
Lowest
6.11.8 Watchdog Timer (WDT_A)
The primary function of the watchdog timer (WDT_A) module is to perform a controlled system restart
after a software problem occurs. If the selected time interval expires, a system reset is generated. If the
watchdog function is not needed in an application, the timer can be configured as an interval timer and
can generate interrupts at selected time intervals.
6.11.9 DMA Controller
The DMA controller allows movement of data from one memory address to another without CPU
intervention. For example, the DMA controller can be used to move data from the ADC10_A conversion
memory to RAM. Using the DMA controller can increase the throughput of peripheral modules. The DMA
controller reduces system power consumption by allowing the CPU to remain in sleep mode, without
having to awaken to move data to or from a peripheral.
Table 6-10. DMA Trigger Assignments (1)
TRIGGER
(1)
CHANNEL
0
1
0
DMAREQ
1
TA0CCR0 CCIFG
2
TA0CCR2 CCIFG
3
TA1CCR0 CCIFG
4
Reserved
5
TA2CCR0 CCIFG
6
Reserved
7
TA3CCR0 CCIFG
8
Reserved
9
Reserved
2
Reserved DMA triggers may be used by other devices in the family.
Reserved DMA triggers do not cause any DMA trigger event when
selected.
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
79
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-10. DMA Trigger Assignments(1) (continued)
TRIGGER
CHANNEL
0
1
10
Reserved
11
Reserved
12
Reserved
13
SD24IFG
14
Reserved
15
Reserved
16
UCA0RXIFG
17
UCA0TXIFG
18
UCA1RXIFG
19
UCA1TXIFG
20
UCA2RXIFG
21
UCA2TXIFG
22
UCB0RXIFG0
23
UCB0TXIFG0
24
ADC10IFG0
25
Reserved
26
Reserved
27
Reserved
28
Reserved
29
MPY ready
30
31
DMA2IFG
DMA0IFG
2
DMA1IFG
Reserved
6.11.10 CRC16
The CRC16 module produces a signature based on a sequence of entered data values and can be used
for data checking purposes. The CRC16 module signature is based on the CRC-CCITT standard.
6.11.11 Hardware Multiplier
The multiplication operation is supported by a dedicated peripheral module. The module performs
operations with 32-bit, 24-bit, 16-bit, and 8-bit operands. The module is capable of supporting signed and
unsigned multiplication as well as signed and unsigned multiply and accumulate operations.
6.11.12 Enhanced Universal Serial Communication Interface (eUSCI)
The eUSCI module is used for serial data communication. The eUSCI module supports synchronous
communication protocols such as SPI (3 or 4 pin) and I2C, and asynchronous communication protocols
such as UART, enhanced UART with automatic baudrate detection, and IrDA.
The eUSCI_An module supports for SPI (3 or 4 pin), UART, enhanced UART, or IrDA.
The eUSCI_Bn module supports for SPI (3 or 4 pin) or I2C.
Three eUSCI_A and one eUSCI_B module are implemented.
6.11.13 ADC10_A
The ADC10_A module supports fast 10-bit analog-to-digital conversions. The module implements a 10-bit
SAR core, sample select control, reference generator, and a conversion results buffer. A window
comparator with a lower and upper limit allows CPU independent result monitoring with three window
comparator interrupt flags.
80
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.14 SD24_B
The SD24_B module integrates up to three independent 24-bit sigma-delta A/D converters. Each
converter is designed with a fully differential analog input pair and programmable gain amplifier input
stage. The converters are based on second-order over-sampling sigma-delta modulators and digital
decimation filters. The decimation filters are comb type filters with selectable oversampling ratios of up to
1024.
6.11.15 TA0
TA0 is a 16-bit timer/counter (Timer_A type) with three capture/compare registers. TA0 can support
multiple capture/compares, PWM outputs, and interval timing. TA0 also has extensive interrupt
capabilities. Interrupts may be generated from the counter on overflow conditions and from each of the
capture/compare registers.
Table 6-11. TA0 Signal Connections
DEVICE INPUT SIGNAL
MODULE INPUT NAME
PM_TACLK
TACLK
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
PM_TACLK
INCLK
PM_TA0.0
CCI0A
DVSS
CCI0B
DVSS
GND
MODULE BLOCK
MODULE OUTPUT
SIGNAL
DEVICE OUTPUT
SIGNAL
Timer
NA
NA
PM_TA0.0
CCR0
TA0
DVCC
VCC
PM_TA0.1
CCI1A
PM_TA0.1
ACLK (internal)
CCI1B
ADC10_A (internal)
ADC10SHSx = {1}
DVSS
GND
DVCC
VCC
PM_TA0.2
CCI2A
DVSS
CCI2B
DVSS
GND
DVCC
VCC
CCR1
TA1
SD24_B (internal)
SD24SCSx = {1}
PM_TA0.2
CCR2
TA2
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
81
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.16 TA1
TA1 is a 16-bit timer/counter (Timer_A type) with two capture/compare registers. TA1 can support multiple
capture/compares, PWM outputs, and interval timing. TA1 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the
capture/compare registers.
Table 6-12. TA1 Signal Connections
DEVICE INPUT SIGNAL
PM_TACLK
MODULE INPUT NAME
MODULE BLOCK
MODULE OUTPUT
SIGNAL
DEVICE OUTPUT
SIGNAL
PZ
TACLK
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
PM_TACLK
INCLK
PM_TA1.0
CCI0A
DVSS
CCI0B
DVSS
GND
DVCC
VCC
PM_TA1.1
CCI1A
ACLK (internal)
CCI1B
DVSS
GND
DVCC
VCC
Timer
NA
NA
PM_TA1.0
CCR0
TA0
PM_TA1.1
CCR1
TA1
6.11.17 TA2
TA2 is a 16-bit timer/counter (Timer_A type) with two capture/compare registers. TA2 can support multiple
capture/compares, PWM outputs, and interval timing. TA2 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the
capture/compare registers.
Table 6-13. TA2 Signal Connections
DEVICE INPUT SIGNAL
MODULE INPUT NAME
PM_TACLK
TACLK
82
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
PM_TACLK
INCLK
PM_TA2.0
CCI0A
DVSS
CCI0B
DVSS
GND
MODULE BLOCK
MODULE OUTPUT
SIGNAL
DEVICE OUTPUT
SIGNAL
Timer
NA
NA
PM_TA2.0
CCR0
TA0
DVCC
VCC
PM_TA2.1
CCI1A
PM_TA2.1
ACLK (internal)
CCI1B
SD24_B (internal)
SD24SCSx = {2}
DVSS
GND
DVCC
VCC
Detailed Description
CCR1
TA1
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.18 TA3
TA3 is a 16-bit timer/counter (Timer_A type) with two capture/compare registers. TA3 can support multiple
capture/compares, PWM outputs, and interval timing. TA3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the
capture/compare registers.
Table 6-14. TA3 Signal Connections
DEVICE INPUT SIGNAL
MODULE INPUT NAME
PM_TACLK
TACLK
MODULE BLOCK
MODULE OUTPUT
SIGNAL
Timer
NA
DEVICE OUTPUT
SIGNAL
ACLK (internal)
ACLK
SMCLK (internal)
SMCLK
PM_TACLK
INCLK
PM_TA3.0
CCI0A
PM_TA3.0
DVSS
CCI0B
TA0
ADC10_A (internal)
ADC10SHSx = {2}
DVSS
GND
TA1
CCR0
DVCC
VCC
PM_TA3.1
CCI1A
PM_TA3.1
ACLK (internal)
CCI1B
SD24_B (internal)
SD24SCSx = {3}
DVSS
GND
DVCC
VCC
CCR1
6.11.19 SD24_B Triggers
Table 6-15 shows the input trigger connections to SD24_B converters from Timer_A modules and output
trigger pulse connection from SD24_B to ADC10_A.
Table 6-15. SD24_B Input/Output Trigger Connections
DEVICE INPUT SIGNAL MODULE INPUT SIGNAL
TA0.1 (internal)
SD24_B
SD24SCSx = {1}
TA2.1 (internal)
SD24_B
SD24SCSx = {2}
TA3.1 (internal)
SD24_B
SD24SCSx = {3}
MODULE BLOCK
MODULE OUTPUT
SIGNAL
DEVICE OUTPUT
SIGNAL
Trigger Pulse
ADC10_A (internal)
ADC10SHSx = {3}
SD24_B
6.11.20 ADC10_A Triggers
Table 6-16 shows input trigger connections to ADC10_A from Timer_A modules and SD24_B.
Table 6-16. ADC10_A Input Trigger Connections
DEVICE INPUT SIGNAL
MODULE INPUT SIGNAL
TA0.1 (internal)
ADC10_A
ADC10SHSx = {1}
TA3.0 (internal)
ADC10_A
ADC10SHSx = {2}
MODULE BLOCK
ADC10_A
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
83
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.21 Real-Time Clock (RTC_C)
The RTC_C module can be configured for real-time clock (RTC) or calendar mode providing seconds,
hours, day of week, day of month, month, and year. The RTC_C control and configuration registers are
password protected to ensure clock integrity against runaway code. Calendar mode integrates an internal
calendar that compensates for months with less than 31 days and includes leap year correction. The
RTC_C also supports flexible alarm functions, offset calibration, and temperature compensation. The
RTC_C on this device operates on dedicated AUXVCC3 supply and supports operation in LPM3.5.
6.11.22 REF Voltage Reference
The reference module (REF) is responsible for generation of all critical reference voltages that can be
used by the various analog peripherals in the device. These include the ADC10_A, LCD_C, and SD24_B
modules.
6.11.23 LCD_C
The LCD_C driver generates the segment and common signals required to drive a segment liquid crystal
display (LCD). The LCD_C controller has dedicated data memories to hold segment drive information.
Common and segment signals are generated as defined by the mode. Static, 2-mux, 3-mux, 4-mux, up to
8-mux LCDs are supported. The module can provide a LCD voltage independent of the supply voltage
with its integrated charge pump. It is possible to control the level of the LCD voltage and thus contrast by
software. The module also provides an automatic blinking capability for individual segments in static, 2mux, 3-mux, and 4-mux modes.
6.11.24 Embedded Emulation Module (EEM) (S Version)
The EEM supports real-time in-system debugging. The S version of the EEM implemented on all devices
has the following features:
• Three hardware triggers or breakpoints on memory access
• One hardware trigger or breakpoint on CPU register write access
• Up to four hardware triggers can be combined to form complex triggers or breakpoints
• One cycle counter
• Clock control on module level
84
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25 Input/Output Schematics
6.11.25.1 Port P1, P1.0 and P1.1, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ and
MSP430F67xxAIPN)
Pad Logic
to/from Reference
To ADC10_A
INCHx = y
P1REN.x
P1MAP.x = PMAP_ANALOG
P1DIR.x
0
from Port Mapping
1
P1OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P1.0/PM_TA0.0/VeREF-/A2
P1.1/PM_TA0.1/VeREF+/A1
P1DS.x
0: Low drive
1: High drive
P1SEL.x
P1IN.x
Bus
Keeper
EN
to Port Mapping
D
P1IE.x
EN
P1IRQ.x
Q
P1IFG.x
Set
P1SEL.x
Interrupt
Edge
Select
P1IES.x
Table 6-17. Port P1 (P1.0 and P1.1) Pin Functions (MSP430F67xxAIPZ and MSP430F67xxAIPN)
PIN NAME (P1.x)
P1.0/PM_TA0.0/
VeREF-/A2
x
0
FUNCTION
P1.0 (I/O)
TA0.CCI0A
TA0.TA0
VeREF-/A2
P1.1/PM_TA0.1/
VeREF+/A1
(1)
(2)
1
(2)
CONTROL BITS OR SIGNALS (1)
P1DIR.x
P1SEL.x
P1MAPx
I: 0; O: 1
0
X
0
1
default
1
1
default
= 31
X
1
I: 0; O: 1
0
X
0
1
default
TA0.TA1
1
1
default
VeREF+/A1 (2)
X
1
= 31
P1.1 (I/O)
TA0.CCI1A
X = Don't care
Setting P1SEL.x bit together with P1MAPx = PM_ANALOG disables the output driver and the input Schmitt trigger.
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
85
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.2 Port P1, P1.2, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ and MSP430F67xxAIPN)
Pad Logic
To ADC10_A
INCHx = y
P1REN.x
P1MAP.x = PMAP_ANALOG
P1DIR.x
0
from Port Mapping
1
P1OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P1.2/PM_UCA0RXD/PM_UCA0SOMI/A0
P1DS.x
0: Low drive
1: High drive
P1SEL.x
P1IN.x
Bus
Keeper
EN
to Port Mapping
D
P1IE.x
EN
P1IRQ.x
Q
P1IFG.x
P1SEL.x
P1IES.x
Set
Interrupt
Edge
Select
Table 6-18. Port P1 (P1.2) Pin Functions (MSP430F67xxAIPZ and MSP430F67xxAIPN)
PIN NAME (P1.x)
x
P1.2/PM_UCA0RXD/
PM_UCA0SOMI/A0
2
(1)
(2)
86
FUNCTION
CONTROL BITS OR SIGNALS (1)
P1DIR.x
P1SEL.x
P1MAPx
I: 0; O: 1
0
X
UCA0RXD/UCA0SOMI
X
1
default
A0 (2)
X
1
= 31
P1.2 (I/O)
X = Don't care
Setting P1SEL.x bit together with P1MAPx = PM_ANALOG disables the output driver and the input Schmitt trigger.
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.3 Port P1, P1.3 to P1.5, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ and
MSP430F67xxAIPN)
to LCD_C
Pad Logic
P1REN.x
P1MAP.x = PMAP_ANALOG
P1DIR.x
0
from Port Mapping
1
P1OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P1DS.x
0: Low drive
1: High drive
P1SEL.x
P1.3/PM_UCA0TXD/PM_UCA0SIMO/R03
P1.4/PM_UCA1RXD/PM_UCA1SOMI/LCDREF/R13
P1.5/PM_UCA1TXD/PM_UCA1SIMO/R23
P1IN.x
Bus
Keeper
EN
to Port Mapping
D
P1IE.x
EN
P1IRQ.x
Q
P1IFG.x
P1SEL.x
P1IES.x
Set
Interrupt
Edge
Select
Table 6-19. Port P1 (P1.3 to P1.5) Pin Functions (MSP430F67xxAIPZ and MSP430F67xxAIPN)
PIN NAME (P1.x)
x
P1.3/PM_UCA0TXD/
PM_UCA0SIMO/R03
3
P1.4/PM_UCA1RXD/
PM_UCA1SOMI/
LCDREF/R13
P1.5/PM_UCA1TXD/
PM_UCA1SIMO/R23
(1)
(2)
4
5
FUNCTION
CONTROL BITS OR SIGNALS (1)
P1DIR.x
P1SEL.x
I: 0; O: 1
0
X
UCA0TXD/UCA0SIMO
X
1
default
R03 (2)
X
1
= 31
P1.3 (I/O)
P1.4 (I/O)
P1MAPx
I: 0; O: 1
0
X
UCA1RXD/UCA1SOMI
X
1
default
LCDREF/R13 (2)
X
1
= 31
P1.5 (I/O)
I: 0; O: 1
0
X
UCA1TXD/UCA1SIMO
X
1
default
R23 (2)
X
1
= 31
X = Don't care
Setting P1SEL.x bit together with P1MAPx = PM_ANALOG disables the output driver and the input Schmitt trigger.
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
87
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.4 Port P1, P1.6 and P1.7 (MSP430F67xxAIPZ and MSP430F67xxAIPN),
Port P2, P2.0 and P2.1 (MSP430F67xxAIPZ Only) Input/Output With Schmitt Trigger
COM4 to COM7
from LCD_C
Pad Logic
PyREN.x
PyMAP.x = PMAP_ANALOG
PyDIR.x
0
from Port Mapping
1
PyOUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
PyDS.x
0: Low drive
1: High drive
PySEL.x
P1.6/PM_UCA0CLK/COM4
P1.7/PM_UCB0CLK/COM5
P2.0/PM_UCB0SOMI/PM_UCB0SCL/COM6
P2.1/PM_UCB0SIMO/PM_UCB0SDA/COM7
PyIN.x
Bus
Keeper
EN
to Port Mapping
D
PyIE.x
EN
PyIRQ.x
Q
PyIFG.x
PySEL.x
PyIES.x
88
Detailed Description
Set
Interrupt
Edge
Select
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-20. Port P1 (P1.6 and P1.7) Pin Functions (MSP430F67xxAIPZ and MSP430F67xxAIPN)
CONTROL BITS OR SIGNALS (1)
PIN NAME (P1.x)
P1.6/PM_UCA0CLK/COM4
x
6
FUNCTION
P1DIR.x
P1SEL.x
P1MAPx
COM4,5
Enable Signal
P1.6 (I/O)
I: 0; O: 1
0
X
0
UCA0CLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
COM4
P1.7/PM_UCB0CLK/COM5
(1)
7
X
X
X
1
P1.7 (I/O)
I: 0; O: 1
0
X
0
UCB0CLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
COM5
X
X
X
1
X = Don't care
Table 6-21. Port P2 (P2.0 and P2.1) Pin Functions (MSP430F67xxAIPZ Only)
CONTROL BITS OR SIGNALS (1)
PIN NAME (P2.x)
P2.0/PM_UCB0SOMI/
PM_UCB0SCL/COM6
x
0
FUNCTION
P2DIR.x
P2SEL.x
P2MAPx
COM6,7
Enable Signal
I: 0; O: 1
0
X
0
UCB0SOMI/UCB0SCL
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
P2.0 (I/O)
COM6
P2.1/PM_UCB0SIMO/
PM_UCB0SDA/COM7
(1)
1
X
X
X
1
I: 0; O: 1
0
X
0
UCB0SIMO/UCB0SDA
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
COM7
X
X
X
1
P2.1 (I/O)
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
89
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.5 Port P2, P2.2 to P2.7, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
Pad Logic
P2REN.x
P2MAP.x = PMAP_ANALOG
P2DIR.x
0
from Port Mapping
1
P2OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
Direction
0: Input
1: Output
P2DS.x
0: Low drive
1: High drive
P2SEL.x
P2IN.x
P2.2/PM_UCA2RXD/PM_UCA2SOMI
P2.3/PM_UCA2TXD/PM_UCA2SIMO
P2.4/PM_UCA1CLK
P2.5/PM_UCA2CLK
P2.6/PM_TA1.0
P2.7/PM_TA1.1
Bus
Keeper
EN
to Port Mapping
1
D
P2IE.x
EN
P2IRQ.x
Q
P2IFG.x
P2SEL.x
P2IES.x
90
Detailed Description
Set
Interrupt
Edge
Select
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-22. Port P2 (P2.2 to P2.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P2.x)
x
P2.2/PM_UCA2RXD/
PM_UCA2SOMI
2
P2.3/PM_UCA2TXD/
PM_UCA2SIMO
3
P2.4/PM_UCA1CLK
4
FUNCTION
P2.2 (I/O)
UCA2RXD/UCA2SOMI
Output driver and input Schmitt trigger disabled
P2.3 (I/O)
UCA2TXD/UCA2SIMO
Output driver and input Schmitt trigger disabled
P2.6/PM_TA1.0
5
6
7
0
P2MAPx
X
X
1
default
= 31
X
1
I: 0; O: 1
0
X
X
1
default
= 31
X
1
0
X
UCA1CLK
X
1
default
= 31
X
1
P2.5 (I/O)
I: 0; O: 1
0
X
UCA2CLK
X
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
P2.6 (I/O)
I: 0; O: 1
0
X
TA1.CC10A
0
1
default
TA1.TA0
1
1
default
= 31
X
1
I: 0; O: 1
0
X
0
1
default
TA1.TA1
1
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
P2.7 (I/O)
TA1.CCI1A
(1)
P2SEL.x
I: 0; O: 1
Output driver and input Schmitt trigger disabled
P2.7/PM_TA1.1
P2DIR.x
I: 0; O: 1
P2.4 (I/O)
Output driver and input Schmitt trigger disabled
P2.5/PM_UCA2CLK
CONTROL BITS OR SIGNALS (1)
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
91
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.6 Port P3, P3.0 to P3.3, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
Pad Logic
P3REN.x
P3MAP.x = PMAP_ANALOG
P3DIR.x
0
from Port Mapping
1
P3OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P3.0/PM_TA2.0
P3.1/PM_TA2.1
P3.2/PM_TACLK/PM_RTCCLK
P3.3/PM_TA0.2
P3DS.x
0: Low drive
1: High drive
P3SEL.x
P3IN.x
Bus
Keeper
EN
to Port Mapping
D
Table 6-23. Port P3 (P3.0 to P3.3) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P3.x)
P3.0/PM_TA2.0
x
0
FUNCTION
P3DIR.x
P3SEL.x
I: 0; O: 1
0
X
0
1
default
TA2.TA0
1
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
I: 0; O: 1
0
X
TA2.CCI1A
0
1
default
TA2.TA1
1
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
I: 0; O: 1
0
X
TACLK
0
1
default
RTCCLK
1
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
P3.0 (I/O)
TA2.CC10A
P3.1/PM_TA2.1
P3.2/PM_TACLK/
PM_RTCCLK
P3.3/PM_TA0.2
(1)
92
1
2
3
CONTROL BITS OR SIGNALS (1)
P3.1 (I/O)
P3.2 (I/O)
P3.3 (I/O)
P3MAPx
I: 0; O: 1
0
X
TA0.CCI2A
0
1
default
TA0.TA2
1
1
default
Output driver and input Schmitt trigger disabled
X
1
= 31
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.7 Port P3, P3.4 to P3.7 , Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
S39 to S37
LCDS39 to LCDS37
Pad Logic
P3REN.x
P3MAP.x = PMAP_ANALOG
P3DIR.x
0
from Port Mapping
1
P3OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P3.4/PM_SDCLK/S39
P3.5/PM_SD0DIO/S38
P3.6/PM_SD1DIO/S37
P3.7/PM_SD2DIO/S36
P3DS.x
0: Low drive
1: High drive
P3SEL.x
P3IN.x
Bus
Keeper
EN
to Port Mapping
D
Table 6-24. Port P3 (P3.4 to P3.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P3.x)
P3.4/PM_SDCLK/S39
P3.5/PM_SD0DIO/S38
x
4
5
FUNCTION
P3DIR.x
P3SEL.x
P3MAPx
LCDS39...36
I: 0; O: 1
0
X
0
SDCLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S39
X
X
X
1
P3.4 (I/O)
P3.5 (I/O)
I: 0; O: 1
0
X
0
SD0DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S38
P3.6/PM_SD1DIO/S37
P3.7/PM_SD2DIO/S36
(1)
6
7
CONTROL BITS OR SIGNALS (1)
X
X
X
1
I: 0; O: 1
0
X
0
SD1DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S37
X
X
X
1
P3.6 (I/O)
P3.7 (I/O)
I: 0; O: 1
0
X
0
SD2DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S36
X
X
X
1
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
93
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.8 Port P4, Port P5, Port P6, Port P7, Port P8, P8.0 to P8.3 Input/Output With Schmitt Trigger
(MSP430F67xxAIPZ Only)
Sz
LCDSz
Pad Logic
PyREN.x
PyDIR.x
0
0
DVSS
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
PyOUT.x
DVSS
PyDS.x
0: Low drive
1: High drive
PySEL.x
Py.x/Sz
PyIN.x
EN
Not Used
94
Bus
Keeper
D
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-25. Port P4 (P4.0 to P4.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P4.x)
P4.0/S35
x
0
FUNCTION
P4.0 (I/O)
N/A
P4.1/S34
1
P4.2/S33
2
P4.3/S32
3
4
5
6
P4.7/S28
(1)
7
LCDS35...28
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S34
X
X
1
P4.1 (I/O)
P4.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S33
X
X
1
P4.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P4.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S31
X
X
1
I: 0; O: 1
0
0
0
1
0
P4.5 (I/O)
N/A
P4.6/S29
P4SEL.x
S35
N/A
P4.5/S30
P4DIR.x
I: 0; O: 1
DVSS
S32
P4.4/S31
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S30
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S29
X
X
1
P4.6 (I/O)
P4.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S28
X
X
1
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
95
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-26. Port P5 (P5.0 to P5.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P5.x)
P5.0/S27
x
0
FUNCTION
P5.0 (I/O)
N/A
P5.1/S26
1
P5.2/S25
2
P5.3/S24
3
4
5
6
P5.7/S20
(1)
96
7
LCDS27...20
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S26
X
X
1
P5.1 (I/O)
P5.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S25
X
X
1
P5.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P5.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S23
X
X
1
I: 0; O: 1
0
0
0
1
0
P5.5 (I/O)
N/A
P5.6/S21
P5SEL.x
S27
N/A
P5.5/S22
P5DIR.x
I: 0; O: 1
DVSS
S24
P5.4/S23
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S22
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S21
X
X
1
P5.6 (I/O)
P5.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S20
X
X
1
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-27. Port P6 (P6.0 to P6.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P6.x)
P6.0/S19
x
0
FUNCTION
P6.0 (I/O)
N/A
P6.1/S18
1
P6.2/S17
2
P6.3/S16
3
4
5
6
P6.7/S12
(1)
7
LCDS19...12
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S18
X
X
1
P6.1 (I/O)
P6.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S17
X
X
1
P6.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P6.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S15
X
X
1
I: 0; O: 1
0
0
0
1
0
P6.5 (I/O)
N/A
P6.6/S13
P6SEL.x
S19
N/A
P6.5/S14
P6DIR.x
I: 0; O: 1
DVSS
S16
P6.4/S15
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S14
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S13
X
X
1
P6.6 (I/O)
P6.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S12
X
X
1
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
97
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-28. Port P7 (P7.0 to P7.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P7.x)
P7.0/S11
x
0
FUNCTION
P7.0 (I/O)
N/A
P7.1/S10
1
P7.2/S9
2
P7.3/S8
3
4
5
6
P7.7/S4
(1)
98
7
LCDS11...4
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S10
X
X
1
P7.1 (I/O)
P7.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S9
X
X
1
P7.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P7.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S7
X
X
1
I: 0; O: 1
0
0
0
1
0
P7.5 (I/O)
N/A
P7.6/S5
P7SEL.x
S11
N/A
P7.5/S6
P7DIR.x
I: 0; O: 1
DVSS
S8
P7.4/S7
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S6
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S5
X
X
1
P7.6 (I/O)
P7.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S4
X
X
1
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-29. Port P8 (P8.0 to P8.3) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P8.x)
P8.0/S3
x
0
FUNCTION
P8.0 (I/O)
N/A
P8.1/S2
1
P8.2/S1
2
P8.3/S0
(1)
3
CONTROL BITS OR SIGNALS (1)
P8DIR.x
P8SEL.x
LCDS3...0
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S3
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S2
X
X
1
P8.1 (I/O)
P8.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S1
X
X
1
P8.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S0
X
X
1
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
99
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.9 Port P8, P8.4 to P8.7, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
Pad Logic
P8REN.x
P8DIR.x
0
0
DVCC
1
1
Direction
0: Input
1: Output
1
P8OUT.x
DVSS
0
1
Module X OUT
P8.4/TA1.0
P8.5/TA1.1
P8.6/TA2.0
P8.7/TA2.1
P8DS.x
0: Low drive
1: High drive
P8SEL.x
P8IN.x
EN
Module X IN
D
Table 6-30. Port P8 (P8.4 to P8.7) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P8.x)
P8.4/TA1.0
4
P8.5/TA1.1
5
P8.6/TA2.0
6
P8.7/TA2.1
100
x
7
Detailed Description
FUNCTION
CONTROL BITS OR SIGNALS
P8DIR.x
P8SEL.x
I: 0; O: 1
0
TA1.CCI0A
0
1
TA1.TA0
1
1
P8.5 (I/O)
P8.4 (I/O)
I: 0; O: 1
0
TA1.CCI1A
0
1
TA1.TA1
1
1
P8.6 (I/O)
I: 0; O: 1
0
TA2.CCI0A
0
1
TA2.TA0
1
1
P8.7 (I/O)
I: 0; O: 1
0
TA2.CCI1A
0
1
TA2.TA1
1
1
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.10 Port P9, P9.0, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
Pad Logic
P9REN.x
P9DIR.x
0
Module X OUT
0
DVCC
1
1
Direction
0: Input
1: Output
1
P9OUT.x
DVSS
0
1
P9.0/TACLK/RTCCLK
P9DS.x
0: Low drive
1: High drive
P9SEL.x
P9IN.x
EN
Module X IN
D
Table 6-31. Port P9 (P9.0) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P9.x)
P9.0/TACLK/RTCCLK
x
0
FUNCTION
CONTROL BITS OR SIGNALS
P9DIR.x
P9SEL.x
I: 0; O: 1
0
TACLK
0
1
RTCCLK
1
1
P9.0 (I/O)
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
101
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.11 Port P9, P9.1 to P9.3, Input/Output With Schmitt Trigger (MSP430F67xxAIPZ Only)
Pad Logic
To ADC10
INCHx = y
P9REN.x
DVSS
0
DVCC
1
1
P9DIR.x
P9OUT.x
P9.1/A5
P9.2/A4
P9.3/A3
P9DS.x
0: Low drive
1: High drive
P9SEL.x
P9IN.x
Bus
Keeper
Table 6-32. Port P9 (P9.1 to P9.3) Pin Functions (MSP430F67xxAIPZ Only)
PIN NAME (P9.x)
P9.1/A5
x
1
FUNCTION
P9.1 (I/O)
A5
P9.2/A4
2
(2)
P9.2 (I/O)
A4 (2)
P9.3/A3
3
P9.3 (I/O)
A3 (2)
(1)
(2)
102
CONTROL BITS OR SIGNALS (1)
P9DIR.x
P9SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
X = Don't care
Setting P9SEL.x bit disables the output driver and the input Schmitt trigger.
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.12 Port P2, P2.0 and P2.1, Input/Output With Schmitt Trigger (MSP430F67xxAIPN Only)
S39, S38
LCDS39, LCDS38
COM6, COM7
from LCD_C
Pad Logic
P2REN.x
P2MAP.x = PMAP_ANALOG
P2DIR.x
0
from Port Mapping
1
P2OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P2DS.x
0: Low drive
1: High drive
P2SEL.x
P2.0/PM_UCB0SOMI/PM_UCB0SCL/COM6/S39
P2.1/PM_UCB0SIMO/PM_UCB0SDA/COM7/S38
P2IN.x
Bus
Keeper
EN
to Port Mapping
D
P2IE.x
EN
P2IRQ.x
Q
P2IFG.x
P2SEL.x
P2IES.x
Set
Interrupt
Edge
Select
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
103
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-33. Port P2 (P2.0 and P2.1) Pin Functions (MSP430F67xxAIPN Only)
CONTROL BITS OR SIGNALS (1)
PIN NAME (P2.x)
P2.0/PM_UCB0SOMI/
PM_UCB0SCL/COM6/
S39
P2.1/PM_UCB0SIMO/
PM_UCB0SDA/COM7/
S38
(1)
104
x
0
1
FUNCTION
P2.0 (I/O)
P2DIR.x
P2SEL.x
P2MAPx
LCDS39,
LCDS38
COM6,7
Enable
Signal
I: 0; O: 1
0
X
0
0
UCB0SOMI/UCB0SCL
X
1
default
0
0
Output driver and input
Schmitt trigger disabled
X
1
= 31
0
0
COM6
X
X
X
X
1
S39
X
X
X
1
0
I: 0; O: 1
0
X
0
0
UCB0SIMO/UCB0SDA
X
1
default
0
0
Output driver and input
Schmitt trigger disabled
X
1
= 31
0
0
COM7
X
X
X
X
1
S38
X
X
X
1
0
P2.1 (I/O)
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.13 Port P2, P2.2 to P2.7 , Input/Output With Schmitt Trigger (MSP430F67xxAIPN Only)
S37...S32
LCDS37...LCDS32
Pad Logic
P2REN.x
P2MAP.x = PMAP_ANALOG
P2DIR.x
0
from Port Mapping
1
P2OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
Direction
0: Input
1: Output
P2DS.x
0: Low drive
1: High drive
P2SEL.x
P2IN.x
P2.2/PM_UCA2RXD/PM_UCA2SOMI/S37
P2.3/PM_UCA2TXD/PM_UCA2SIMO/S36
P2.4/PM_UCA1CLK/S35
P2.5/PM_UCA2CLK/S34
P2.6/PM_TA1.0/S33
P2.7/PM_TA1.1/S32
Bus
Keeper
EN
to Port Mapping
1
D
P2IE.x
EN
P2IRQ.x
Q
P2IFG.x
P2SEL.x
P2IES.x
Set
Interrupt
Edge
Select
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
105
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-34. Port P2 (P2.2 to P2.7) Pin Functions (MSP430F67xxAIPN Only)
PIN NAME (P2.x)
P2.2/PM_UCA2RXD/
PM_UCA2SOMI/S37
P2.3/PM_UCA2TXD/
PM_UCA2SIMO/S36
x
2
3
FUNCTION
P2DIR.x
P2SEL.x
P2MAPx
LCDS37...32
I: 0; O: 1
0
X
0
UCA2RXD/UCA2SOMI
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S37
X
X
X
1
P2.2 (I/O)
P2.3 (I/O)
I: 0; O: 1
0
X
0
UCA2TXD/UCA2SIMO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S36
P2.4/PM_UCA1CLK/S35
4
X
X
X
1
P2.4 (I/O)
I: 0; O: 1
0
X
0
UCA1CLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S35
P2.5/PM_UCA2CLK/S34
5
X
X
X
1
P2.5 (I/O)
I: 0; O: 1
0
X
0
UCA2CLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S34
P2.6/PM_TA1.0/S33
P2.7/PM_TA1.1/S32
(1)
106
6
7
CONTROL BITS OR SIGNALS (1)
X
X
X
1
I: 0; O: 1
0
X
0
TA1.CCI0A
0
1
default
0
TA1.TA0
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S33
X
X
X
1
P2.6 (I/O)
P2.7 (I/O)
I: 0; O: 1
0
X
0
TA1.CCI1A
0
1
default
0
TA1.TA1
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S32
X
X
X
1
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.14 Port P3, P3.0 to P3.7 , Input/Output With Schmitt Trigger (MSP430F67xxAIPN Only)
S31 to S24
LCDS31 to LCDS24
Pad Logic
P3REN.x
P3MAP.x = PMAP_ANALOG
P3DIR.x
0
from Port Mapping
1
P3OUT.x
0
from Port Mapping
1
DVSS
0
DVCC
1
Direction
0: Input
1: Output
P3DS.x
0: Low drive
1: High drive
P3SEL.x
P3IN.x
EN
to Port Mapping
1
Bus
Keeper
P3.0/PM_TA2.0/S31
P3.1/PM_TA2.1/S30
P3.2/PM_TACLK/PM_RTCCLK/S29
P3.3/PM_TA0.2/S28
P3.4/PM_SDCLK/S27
P3.5/PM_SD0DIO/S26
P3.6/PM_SD1DIO/S25
P3.7/PM_SD2DIO/S24
D
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
107
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-35. Port P3 (P3.0 to P3.7) Pin Functions (MSP430F67xxAIPN Only)
PIN NAME (P3.x)
P3.0/PM_TA2.0/S31
x
0
FUNCTION
P3DIR.x
P3SEL.x
P3MAPx
LCDS31...24
I: 0; O: 1
0
X
0
TA2.CCI0A
0
1
default
0
TA2.TA0
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
P3.0 (I/O)
S31
P3.1/PM_TA2.1/S30
P3.2/PM_TACLK/
PM_RTCCLK/S29
1
2
X
X
X
1
I: 0; O: 1
0
X
0
TA2.CCI1A
0
1
default
0
TA2.TA1
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S30
X
X
X
1
P3.1 (I/O)
P3.2 (I/O)
I: 0; O: 1
0
X
0
TACLK
0
1
default
0
RTCCLK
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S29
P3.3/PM_TA0.2/S28
3
X
X
X
1
I: 0; O: 1
0
X
0
TA0.CCI2A
0
1
default
0
TA0.TA2
1
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
P3.3 (I/O)
S28
P3.4/PM_SDCLK/S27
P3.5/PM_SD0DIO/S26
4
5
X
X
X
1
I: 0; O: 1
0
X
0
SDCLK
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S27
X
X
X
1
P3.4 (I/O)
P3.5 (I/O)
I: 0; O: 1
0
X
0
SD0DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S26
P3.6/PM_SD1DIO/S25
6
X
X
X
1
I: 0; O: 1
0
X
0
SD1DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
P3.6 (I/O)
S25
P3.7/PM_SD2DIO/S24
(1)
108
7
CONTROL BITS OR SIGNALS (1)
X
X
X
1
I: 0; O: 1
0
X
0
SD2DIO
X
1
default
0
Output driver and input Schmitt
trigger disabled
X
1
= 31
0
S24
X
X
X
1
P3.7 (I/O)
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.15 Port P4, Port P5, Port P6, Input/Output With Schmitt Trigger (MSP430F67xxAIPN Only)
Sz
LCDSz
Pad Logic
PyREN.x
PyDIR.x
0
0
DVSS
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
PyOUT.x
DVSS
PyDS.x
0: Low drive
1: High drive
PySEL.x
Py.x/Sz
PyIN.x
EN
Not Used
Bus
Keeper
D
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
109
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-36. Port P4 (P4.0 to P4.7) Pin Functions (MSP430F67xxAIPN Only)
PIN NAME (P4.x)
P4.0/S23
x
0
FUNCTION
P4.0 (I/O)
N/A
P4.1/S22
1
P4.2/S21
2
P4.3/S20
3
4
5
6
P4.7/S16
(1)
110
7
LCDS23...16
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S22
X
X
1
P4.1 (I/O)
P4.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S21
X
X
1
P4.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P4.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S19
X
X
1
I: 0; O: 1
0
0
0
1
0
P4.5 (I/O)
N/A
P4.6/S17
P4SEL.x
S23
N/A
P4.5/S18
P4DIR.x
I: 0; O: 1
DVSS
S20
P4.4/S19
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S18
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S17
X
X
1
P4.6 (I/O)
P4.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S16
X
X
1
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-37. Port P5 (P5.0 to P5.7) Pin Functions (MSP430F67xxAIPN Only)
PIN NAME (P5.x)
P5.0/S15
x
0
FUNCTION
P5.0 (I/O)
N/A
P5.1/S14
1
P5.2/S13
2
P5.3/S12
3
4
5
6
P5.7/S8
(1)
7
LCDS15...8
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S14
X
X
1
P5.1 (I/O)
P5.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S13
X
X
1
P5.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P5.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S11
X
X
1
I: 0; O: 1
0
0
0
1
0
P5.5 (I/O)
N/A
P5.6/S9
P5SEL.x
S15
N/A
P5.5/S10
P5DIR.x
I: 0; O: 1
DVSS
S12
P5.4/S11
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S10
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S9
X
X
1
P5.6 (I/O)
P5.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S8
X
X
1
X = Don't care
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
111
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-38. Port P6 (P6.0 to P6.7) Pin Functions (MSP430F67xxAIPN Only)
PIN NAME (P6.x)
P6.0/S7
x
0
FUNCTION
P6.0 (I/O)
N/A
P6.1/S6
1
P6.2/S5
2
P6.3/S4
3
4
5
6
P6.7/S0
(1)
112
7
LCDS7...0
0
0
0
1
0
1
1
0
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S6
X
X
1
P6.1 (I/O)
P6.2 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S5
X
X
1
P6.3 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
P6.4 (I/O)
X
X
1
I: 0; O: 1
0
0
0
1
0
DVSS
1
1
0
S3
X
X
1
I: 0; O: 1
0
0
0
1
0
P6.5 (I/O)
N/A
P6.6/S1
P6SEL.x
S7
N/A
P6.5/S2
P6DIR.x
I: 0; O: 1
DVSS
S4
P6.4/S3
CONTROL BITS OR SIGNALS (1)
DVSS
1
1
0
S2
X
X
1
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S1
X
X
1
P6.6 (I/O)
P6.7 (I/O)
I: 0; O: 1
0
0
N/A
0
1
0
DVSS
1
1
0
S0
X
X
1
X = Don't care
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.11.25.16 Port J, J.0, JTAG pin TDO, Input/Output With Schmitt Trigger or Output
Pad Logic
PJREN.x
PJDIR.x
0
DVCC
1
PJOUT.x
00
From JTAG
01
SMCLK
10
DVSS
0
DVCC
1
PJDS.0
0: Low drive
1: High drive
11
1
PJ.0/SMCLK/TDO
PJSEL.x
From JTAG
PJIN.x
EN
Bus
Holder
D
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
113
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.11.25.17 Port J, J.1 to J.3, JTAG pins TMS, TCK, TDI/TCLK, Input/Output With Schmitt Trigger or
Output
Pad Logic
PJREN.x
PJDIR.x
DVSS
PJOUT.x
DVSS
0
DVCC
1
1
0
1
00
From JTAG
01
MCLK/ADC10CLK/ACLK
10
PJ.1/MCLK/TDI/TCLK
PJ.2/ADC10CLK/TMS
PJ.3/ACLK/TCK
PJDS.x
0: Low drive
1: High drive
11
PJSEL.x
From JTAG
PJIN.x
Bus
Holder
EN
D
To JTAG
Table 6-39. Port PJ (PJ.0 to PJ.3) Pin Functions
CONTROL BITS OR SIGNALS (1)
PIN NAME (PJ.x)
PJ.0/SMCLK/TDO
PJ.1/MCLK/TDI/TCLK
x
0
1
FUNCTION
PJ.0 (I/O) (2)
0
0
1
1
0
TDO (3)
X
X
1
I: 0; O: 1
0
0
1
1
0
X
X
1
I: 0; O: 1
0
0
PJ.1 (I/O)
(2)
(3) (4)
PJ.2 (I/O) (2)
ADC10CLK
TMS
PJ.3/ACLK/TCK
3
(3) (4)
PJ.3 (I/O) (2)
ACLK
TCK
(1)
(2)
(3)
(4)
114
JTAG
Mode
Signal
I: 0; O: 1
TDI/TCLK
2
PJSEL.x
SMCLK
MCLK
PJ.2/ADC10CLK/TMS
PJDIR.x
(3) (4)
1
1
0
X
X
1
I: 0; O: 1
0
0
1
1
0
X
X
1
X = Don't care
Default condition
The pin direction is controlled by the JTAG module.
In JTAG mode, pullups are activated automatically on TMS, TCK, and TDI/TCLK. PJREN.x are don't care.
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.12 Device Descriptors (TLV)
Table 6-40 and Table 6-41 list the complete contents of the device descriptor tag-length-value (TLV)
structure for each device type.
Table 6-40. MSP430F673xA Device Descriptors
Info Block
Die Record
ADC10
Calibration
DESCRIPTION
ADDRESS
SIZE
(bytes)
F6736A
F6735A
F6734A
F6733A
F6731A
F6730A
VALUE
VALUE
VALUE
VALUE
VALUE
VALUE
Info length
01A00h
1
06h
06h
06h
06h
06h
06h
CRC length
01A01h
1
06h
06h
06h
06h
06h
06h
CRC value
01A02h
2
per unit
per unit
per unit
per unit
per unit
per unit
Device ID
01A04h
1
86h
85h
84h
83h
81h
80h
Device ID
01A05h
1
82h
82h
82h
82h
82h
82h
Hardware revision
01A06h
1
per unit
per unit
per unit
per unit
per unit
per unit
Firmware revision
01A07h
1
per unit
per unit
per unit
per unit
per unit
per unit
Die Record Tag
01A08h
1
08h
08h
08h
08h
08h
08h
Die Record length
01A09h
1
0Ah
0Ah
0Ah
0Ah
0Ah
0Ah
Lot/Wafer ID
01A0Ah
4
per unit
per unit
per unit
per unit
per unit
per unit
Die X position
01A0Eh
2
per unit
per unit
per unit
per unit
per unit
per unit
Die Y position
01A10h
2
per unit
per unit
per unit
per unit
per unit
per unit
Test results
01A12h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC10 Calibration Tag
01A14h
1
13h
13h
13h
13h
13h
13h
ADC10 Calibration length
01A15h
1
10h
10h
10h
10h
10h
10h
ADC Gain Factor
01A16h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC Offset
01A18h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 1.5-V Reference
Temp. Sensor 30°C
01A1Ah
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 1.5-V Reference
Temp. Sensor 85°C
01A1Ch
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.0-V Reference
Temp. Sensor 30°C
01A1Eh
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.0-V Reference
Temp. Sensor 85°C
01A20h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.5-V Reference
Temp. Sensor 30°C
01A22h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.5-V Reference
Temp. Sensor 85°C
01A24h
2
per unit
per unit
per unit
per unit
per unit
per unit
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
115
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-41. MSP430F672xA Device Descriptors
Info Block
Die Record
ADC10
Calibration
116
ADDRES
S
SIZE
(byte
s)
F6726A
F6725A
F6724A
F6723A
F6721A
F6720A
DESCRIPTION
VALUE
VALUE
VALUE
VALUE
VALUE
VALUE
Info length
01A00h
1
06h
06h
06h
06h
06h
06h
CRC length
01A01h
1
06h
06h
06h
06h
06h
06h
CRC value
01A02h
2
per unit
per unit
per unit
per unit
per unit
per unit
Device ID
01A04h
1
7Ch
7Bh
7Ah
79h
77h
76h
Device ID
01A05h
1
82h
82h
82h
82h
82h
82h
Hardware revision
01A06h
1
per unit
per unit
per unit
per unit
per unit
per unit
Firmware revision
01A07h
1
per unit
per unit
per unit
per unit
per unit
per unit
Die Record Tag
01A08h
1
08h
08h
08h
08h
08h
08h
Die Record length
01A09h
1
0Ah
0Ah
0Ah
0Ah
0Ah
0Ah
Lot/Wafer ID
01A0Ah
4
per unit
per unit
per unit
per unit
per unit
per unit
Die X position
01A0Eh
2
per unit
per unit
per unit
per unit
per unit
per unit
Die Y position
01A10h
2
per unit
per unit
per unit
per unit
per unit
per unit
Test results
01A12h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC10 Calibration Tag
01A14h
1
13h
13h
13h
13h
13h
13h
ADC10 Calibration length
01A15h
1
10h
10h
10h
10h
10h
10h
ADC Gain Factor
01A16h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC Offset
01A18h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 1.5-V Reference
Temp. Sensor 30°C
01A1Ah
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 1.5-V Reference
Temp. Sensor 85°C
01A1Ch
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.0-V Reference
Temp. Sensor 30°C
01A1Eh
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.0-V Reference
Temp. Sensor 85°C
01A20h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.5-V Reference
Temp. Sensor 30°C
01A22h
2
per unit
per unit
per unit
per unit
per unit
per unit
ADC 2.5-V Reference
Temp. Sensor 85°C
01A24h
2
per unit
per unit
per unit
per unit
per unit
per unit
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.13 Memory
6.13.1 Memory Organization
Table 6-42 and Table 6-43 show the memory organization for all device variants.
Table 6-42. Memory Organization
Main Memory
(flash)
MSP430F6730A
MSP430F6720A
MSP430F6731A
MSP430F6721A
MSP430F6733A
MSP430F6723A
16KB
32KB
64KB
00FFFFh to 00FF80h
00FFFFh to 00FF80h
00FFFFh to 00FF80h
Bank 3
not available
not available
not available
Bank 2
not available
not available
not available
Bank 1
not available
16KB
00FFFFh to 00C000h
32KB
013FFFh to 00C000h
Bank 0
16KB
00FFFFh to 00C000h
16KB
00BFFFh to 008000h
32KB
00BFFFh to 004000h
Total Size
Main: Interrupt
vector
Main: code
memory
RAM
Total Size
Information
memory (flash)
Bootstrap loader
(BSL) memory
(flash)
1KB
2KB
4KB
Sector 3
not available
not available
not available
Sector 2
not available
not available
not available
Sector 1
not available
not available
2KB
002BFFh to 002400h
Sector 0
1KB
001FFFh to 001C00h
2KB
0023FFh to 001C00h
2KB
0023FFh to 001C00h
Info A
128 B
0019FFh to 001980h
128 B
0019FFh to 001980h
128 B
0019FFh to 001980h
Info B
128 B
00197Fh to 001900h
128 B
00197Fh to 001900h
128 B
00197Fh to 001900h
Info C
128 B
0018FFh to 001880h
128 B
0018FFh to 001880h
128 B
0018FFh to 001880h
Info D
128 B
00187Fh to 001800h
128 B
00187Fh to 001800h
128 B
00187Fh to 001800h
BSL 3
512 B
0017FFh to 001600h
512 B
0017FFh to 001600h
512 B
0017FFh to 001600h
BSL 2
512 B
0015FFh to 001400h
512 B
0015FFh to 001400h
512 B
0015FFh to 001400h
BSL 1
512 B
0013FFh to 001200h
512 B
0013FFh to 001200h
512 B
0013FFh to 001200h
BSL 0
512 B
0011FFh to 001000h
512 B
0011FFh to 001000h
512 B
0011FFh to 001000h
4 KB
000FFFh to 0h
4 KB
000FFFh to 0h
4 KB
000FFFh to 0h
Peripherals
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
117
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-43. Memory Organization
Total
Size
Main Memory (flash)
Main: Interrupt vector
Main: code memory
96KB
128KB
128KB
00FFFFh to 00FF80h
00FFFFh to 00FF80h
not available
32KB
023FFFh to 01C000h
32KB
023FFFh to 01C000h
Bank 2
32KB
01BFFFh to 014000h
32KB
01BFFFh to 014000h
32KB
01BFFFh to 014000h
Bank 1
32KB
013FFFh to 00C000h
32KB
013FFFh to 00C000h
32KB
013FFFh to 00C000h
Bank 0
32KB
00BFFFh to 004000h
32KB
00BFFFh to 004000h
32KB
00BFFFh to 004000h
4KB
4KB
8KB
Sector 3
not available
not available
2KB
003BFFh to 003400h
Sector 2
not available
not available
2KB
0033FFh to 002C00h
Sector 1
2KB
002BFFh to 002400h
2KB
002BFFh to 002400h
2KB
002BFFh to 002400h
Sector 0
2KB
0023FFh to 001C00h
2KB
0023FFh to 001C00h
2KB
0023FFh to 001C00h
Info A
128 B
0019FFh to 001980h
128 B
0019FFh to 001980h
128 B
0019FFh to 001980h
Info B
128 B
00197Fh to 001900h
128 B
00197Fh to 001900h
128 B
00197Fh to 001900h
Info C
128 B
0018FFh to 001880h
128 B
0018FFh to 001880h
128 B
0018FFh to 001880h
Info D
128 B
00187Fh to 001800h
128 B
00187Fh to 001800h
128 B
00187Fh to 001800h
BSL 3
512 B
0017FFh to 001600h
512 B
0017FFh to 001600h
512 B
0017FFh to 001600h
BSL 2
512 B
0015FFh to 001400h
512 B
0015FFh to 001400h
512 B
0015FFh to 001400h
BSL 1
512 B
0013FFh to 001200h
512 B
0013FFh to 001200h
512 B
0013FFh to 001200h
BSL 0
512 B
0011FFh to 001000h
512 B
0011FFh to 001000h
512 B
0011FFh to 001000h
4 KB
000FFFh to 0h
4 KB
000FFFh to 0h
4 KB
000FFFh to 0h
Peripherals
118
MSP430F6736A
MSP430F6726A
00FFFFh to 00FF80h
Total
Size
Bootstrap loader
(BSL) memory (flash)
MSP430F6735A
MSP430F6725A
Bank 3
RAM
Information memory
(flash)
MSP430F6734A
MSP430F6724A
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
6.13.2 Peripheral File Map
Table 6-44 shows the available modules with the base address and the offset range for each. Table 6-45
through Table 6-82 show all of the available registers for each module.
Table 6-44. Peripheral File Map
MODULE NAME
BASE ADDRESS
OFFSET ADDRESS
RANGE
Special Functions (see Table 6-45)
0100h
000h-01Fh
PMM (see Table 6-46)
0120h
000h-01Fh
Flash Control (see Table 6-47)
0140h
000h-00Fh
CRC16 (see Table 6-48)
0150h
000h-007h
RAM Control (see Table 6-49)
0158h
000h-001h
Watchdog (see Table 6-50)
015Ch
000h-001h
UCS (see Table 6-51)
0160h
000h-01Fh
SYS (see Table 6-52)
0180h
000h-01Fh
Shared Reference (see Table 6-53)
01B0h
000h-001h
Port Mapping Control (see Table 6-54)
01C0h
000h-007h
Port Mapping Port P1 (see Table 6-55)
01C8h
000h-007h
Port Mapping Port P2 (see Table 6-56)
01D0h
000h-007h
Port Mapping Port P3 (see Table 6-57)
01D8h
000h-007h
Port P1/P2 (see Table 6-58)
0200h
000h-01Fh
Port P3/P4 (see Table 6-59)
0220h
000h-00Bh
Port P5/P6 (see Table 6-60)
0240h
000h-00Bh
Port P7/P8 (see Table 6-61)
(Port P7/P8 not available in MSP430F67xxAIPN)
0260h
000h-00Bh
Port P9 (Port P9 not available in
MSP430F67xxAIPN)
(see Table 6-62)
0280h
000h-00Bh
Port PJ (refer toTable 6-63)
0320h
000h-01Fh
Timer TA0 (see Table 6-64)
0340h
000h-03Fh
Timer TA1 (see Table 6-65)
0380h
000h-03Fh
Timer TA2 (see Table 6-66)
0400h
000h-03Fh
Timer TA3 (see Table 6-67)
0440h
000h-03Fh
Backup Memory (see Table 6-68)
0480h
000h-00Fh
RTC_C (see Table 6-69)
04A0h
000h-01Fh
32-bit Hardware Multiplier (see Table 6-70)
04C0h
000h-02Fh
DMA General Control (see Table 6-71)
0500h
000h-00Fh
DMA Channel 0 (see Table 6-72)
0500h
010h-01Fh
DMA Channel 1 (see Table 6-73)
0500h
020h-02Fh
DMA Channel 2 (see Table 6-74)
0500h
030h-03Fh
eUSCI_A0 (see Table 6-75)
05C0h
000h-01Fh
eUSCI_A1 (see Table 6-76)
05E0h
000h-01Fh
eUSCI_A2 (see Table 6-77)
0600h
000h-01Fh
eUSCI_B0 (see Table 6-78)
0640h
000h-02Fh
ADC10_A (see Table 6-79)
0740h
000h-01Fh
SD24_B(see Table 6-80)
0800h
000h-06Fh
Auxiliary Supply (see Table 6-74)
09E0h
000h-01Fh
LCD_C (see Table 6-82)
0A00h
000h-05Fh
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
119
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-45. Special Function Registers (Base Address: 0100h)
REGISTER DESCRIPTION
REGISTER
OFFSET
SFR interrupt enable
SFRIE1
00h
SFR interrupt flag
SFRIFG1
02h
SFR reset pin control
SFRRPCR
04h
Table 6-46. PMM Registers (Base Address: 0120h)
REGISTER DESCRIPTION
REGISTER
OFFSET
PMM Control 0
PMMCTL0
00h
PMM control 1
PMMCTL1
02h
SVS high side control
SVSMHCTL
04h
SVS low side control
SVSMLCTL
06h
PMM interrupt flags
PMMIFG
0Ch
PMM interrupt enable
PMMIE
0Eh
PMM Power Mode 5 control register 0
PM5CTL0
10h
Table 6-47. Flash Control Registers (Base Address: 0140h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Flash control 1
FCTL1
00h
Flash control 3
FCTL3
04h
Flash control 4
FCTL4
06h
Table 6-48. CRC16 Registers (Base Address: 0150h)
REGISTER DESCRIPTION
REGISTER
OFFSET
CRC data input
CRC16DI
00h
CRC data input reverse byte
CRC16DIRB
02h
CRC result
CRCINIRES
04h
CRC result reverse byte
CRCRESR
06h
Table 6-49. RAM Control Registers (Base Address: 0158h)
REGISTER DESCRIPTION
RAM control 0
REGISTER
RCCTL0
OFFSET
00h
Table 6-50. Watchdog Registers (Base Address: 015Ch)
REGISTER DESCRIPTION
Watchdog timer control
REGISTER
WDTCTL
OFFSET
00h
Table 6-51. UCS Registers (Base Address: 0160h)
REGISTER DESCRIPTION
REGISTER
OFFSET
UCS control 0
UCSCTL0
00h
UCS control 1
UCSCTL1
02h
UCS control 2
UCSCTL2
04h
UCS control 3
UCSCTL3
06h
UCS control 4
UCSCTL4
08h
UCS control 5
UCSCTL5
0Ah
UCS control 6
UCSCTL6
0Ch
UCS control 7
UCSCTL7
0Eh
120
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-51. UCS Registers (Base Address: 0160h) (continued)
REGISTER DESCRIPTION
UCS control 8
REGISTER
UCSCTL8
OFFSET
10h
Table 6-52. SYS Registers (Base Address: 0180h)
REGISTER DESCRIPTION
REGISTER
OFFSET
System control
SYSCTL
00h
Bootstrap loader configuration area
SYSBSLC
02h
JTAG mailbox control
SYSJMBC
06h
JTAG mailbox input 0
SYSJMBI0
08h
JTAG mailbox input 1
SYSJMBI1
0Ah
JTAG mailbox output 0
SYSJMBO0
0Ch
JTAG mailbox output 1
SYSJMBO1
0Eh
Bus Error vector generator
SYSBERRIV
18h
User NMI vector generator
SYSUNIV
1Ah
System NMI vector generator
SYSSNIV
1Ch
Reset vector generator
SYSRSTIV
1Eh
Table 6-53. Shared Reference Registers (Base Address: 01B0h)
REGISTER DESCRIPTION
Shared reference control
REGISTER
REFCTL
OFFSET
00h
Table 6-54. Port Mapping Controller (Base Address: 01C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port mapping password register
PMAPPWD
00h
Port mapping control register
PMAPCTL
02h
Table 6-55. Port Mapping for Port P1 (Base Address: 01C8h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P1.0 mapping register
P1MAP0
00h
Port P1.1 mapping register
P1MAP1
01h
Port P1.2 mapping register
P1MAP2
02h
Port P1.3 mapping register
P1MAP3
03h
Port P1.4 mapping register
P1MAP4
04h
Port P1.5 mapping register
P1MAP5
05h
Port P1.6 mapping register
P1MAP6
06h
Port P1.7 mapping register
P1MAP7
07h
Table 6-56. Port Mapping for Port P2 (Base Address: 01D0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P2.0 mapping register
P2MAP0
00h
Port P2.1 mapping register
P2MAP2
01h
Port P2.2 mapping register
P2MAP2
02h
Port P2.3 mapping register
P2MAP3
03h
Port P2.4 mapping register
P2MAP4
04h
Port P2.5 mapping register
P2MAP5
05h
Port P2.6 mapping register
P2MAP6
06h
Port P2.7 mapping register
P2MAP7
07h
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
121
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-57. Port Mapping for Port P3 (Base Address: 01D8h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P3.0 mapping register
P3MAP0
00h
Port P3.1 mapping register
P3MAP3
01h
Port P3.2 mapping register
P3MAP2
02h
Port P3.3 mapping register
P3MAP3
03h
Port P3.4 mapping register
P3MAP4
04h
Port P3.5 mapping register
P3MAP5
05h
Port P3.6 mapping register
P3MAP6
06h
Port P3.7 mapping register
P3MAP7
07h
Table 6-58. Port P1, P2 Registers (Base Address: 0200h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P1 input
P1IN
00h
Port P1 output
P1OUT
02h
Port P1 direction
P1DIR
04h
Port P1 pullup/pulldown enable
P1REN
06h
Port P1 drive strength
P1DS
08h
Port P1 selection
P1SEL
0Ah
Port P1 interrupt vector word
P1IV
0Eh
Port P1 interrupt edge select
P1IES
18h
Port P1 interrupt enable
P1IE
1Ah
Port P1 interrupt flag
P1IFG
1Ch
Port P2 input
P2IN
01h
Port P2 output
P2OUT
03h
Port P2 direction
P2DIR
05h
Port P2 pullup/pulldown enable
P2REN
07h
Port P2 drive strength
P2DS
09h
Port P2 selection
P2SEL
0Bh
Port P2 interrupt vector word
P2IV
1Eh
Port P2 interrupt edge select
P2IES
19h
Port P2 interrupt enable
P2IE
1Bh
Port P2 interrupt flag
P2IFG
1Dh
Table 6-59. Port P3, P4 Registers (Base Address: 0220h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P3 input
P3IN
00h
Port P3 output
P3OUT
02h
Port P3 direction
P3DIR
04h
Port P3 pullup/pulldown enable
P3REN
06h
Port P3 drive strength
P3DS
08h
Port P3 selection
P3SEL
0Ah
Port P4 input
P4IN
01h
Port P4 output
P4OUT
03h
Port P4 direction
P4DIR
05h
Port P4 pullup/pulldown enable
P4REN
07h
Port P4 drive strength
P4DS
09h
Port P4 selection
P4SEL
0Bh
122
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-60. Port P5, P6 Registers (Base Address: 0240h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P5 input
P5IN
00h
Port P5 output
P5OUT
02h
Port P5 direction
P5DIR
04h
Port P5 pullup/pulldown enable
P5REN
06h
Port P5 drive strength
P5DS
08h
Port P5 selection
P5SEL
0Ah
Port P6 input
P6IN
01h
Port P6 output
P6OUT
03h
Port P6 direction
P6DIR
05h
Port P6 pullup/pulldown enable
P6REN
07h
Port P6 drive strength
P6DS
09h
Port P6 selection
P6SEL
0Bh
Table 6-61. Port P7, P8 Registers (Base Address: 0260h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P7 input
P7IN
00h
Port P7 output
P7OUT
02h
Port P7 direction
P7DIR
04h
Port P7 pullup/pulldown enable
P7REN
06h
Port P7 drive strength
P7DS
08h
Port P7 selection
P7SEL
0Ah
Port P8 input
P8IN
01h
Port P8 output
P8OUT
03h
Port P8 direction
P8DIR
05h
Port P8 pullup/pulldown enable
P8REN
07h
Port P8 drive strength
P8DS
09h
Port P8 selection
P8SEL
0Bh
Table 6-62. Port P9 Registers (Base Address: 0280h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port P9 input
P9IN
00h
Port P9 output
P9OUT
02h
Port P9 direction
P9DIR
04h
Port P9 pullup/pulldown enable
P9REN
06h
Port P9 drive strength
P9DS
08h
Port P9 selection
P9SEL
0Ah
Table 6-63. Port J Registers (Base Address: 0320h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Port PJ input
PJIN
00h
Port PJ output
PJOUT
02h
Port PJ direction
PJDIR
04h
Port PJ pullup/pulldown enable
PJREN
06h
Port PJ drive strength
PJDS
08h
Port PJ selection
PJSEL
0Ah
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
123
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-64. TA0 Registers (Base Address: 0340h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA0 control
TA0CTL
00h
Capture/compare control 0
TA0CCTL0
02h
Capture/compare control 1
TA0CCTL1
04h
Capture/compare control 2
TA0CCTL2
06h
TA0 counter register
TA0R
10h
Capture/compare register 0
TA0CCR0
12h
Capture/compare register 1
TA0CCR1
14h
Capture/compare register 2
TA0CCR2
16h
TA0 expansion register 0
TA0EX0
20h
TA0 interrupt vector
TA0IV
2Eh
Table 6-65. TA1 Registers (Base Address: 0380h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA1 control
TA1CTL
00h
Capture/compare control 0
TA1CCTL0
02h
Capture/compare control 1
TA1CCTL1
04h
TA1 counter register
TA1R
10h
Capture/compare register 0
TA1CCR0
12h
Capture/compare register 1
TA1CCR1
14h
TA1 expansion register 0
TA1EX0
20h
TA1 interrupt vector
TA1IV
2Eh
Table 6-66. TA2 Registers (Base Address: 0400h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA2 control
TA2CTL
00h
Capture/compare control 0
TA2CCTL0
02h
Capture/compare control 1
TA2CCTL1
04h
TA2 counter register
TA2R
10h
Capture/compare register 0
TA2CCR0
12h
Capture/compare register 1
TA2CCR1
14h
TA2 expansion register 0
TA2EX0
20h
TA2 interrupt vector
TA2IV
2Eh
Table 6-67. TA3 Registers (Base Address: 0440h)
REGISTER DESCRIPTION
REGISTER
OFFSET
TA3 control
TA3CTL
00h
Capture/compare control 0
TA3CCTL0
02h
Capture/compare control 1
TA3CCTL1
04h
TA3 counter register
TA3R
10h
Capture/compare register 0
TA3CCR0
12h
Capture/compare register 1
TA3CCR1
14h
TA3 expansion register 0
TA3EX0
20h
TA3 interrupt vector
TA3IV
2Eh
124
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-68. Backup Memory Registers (Base Address: 0480h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Backup Memory 0
BAKMEM0
00h
Backup Memory 1
BAKMEM1
02h
Backup Memory 2
BAKMEM2
04h
Backup Memory 3
BAKMEM3
06h
Table 6-69. RTC_C Registers (Base Address: 04A0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
RTC control 0
RTCCTL0
00h
RTC password
RTCPWD
01h
RTC control 1
RTCCTL1
02h
RTC control 3
RTCCTL3
03h
RTC offset calibration
RTCOCAL
04h
RTC temperature compensation
RTCTCMP
06h
RTC prescaler 0 control
RTCPS0CTL
08h
RTC prescaler 1 control
RTCPS1CTL
0Ah
RTC prescaler 0
RTCPS0
0Ch
RTC prescaler 1
RTCPS1
0Dh
RTC interrupt vector word
RTCIV
0Eh
RTC seconds
RTCSEC
10h
RTC minutes
RTCMIN
11h
RTC hours
RTCHOUR
12h
RTC day of week
RTCDOW
13h
RTC days
RTCDAY
14h
RTC month
RTCMON
15h
RTC year
RTCYEAR
16h
RTC alarm minutes
RTCAMIN
18h
RTC alarm hours
RTCAHOUR
19h
RTC alarm day of week
RTCADOW
1Ah
RTC alarm days
RTCADAY
1Bh
Binary-to-BCD conversion register
BIN2BCD
1Ch
BCD-to-Binary conversion register
BCD2BIN
1Eh
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
125
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-70. 32-Bit Hardware Multiplier Registers (Base Address: 04C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
16-bit operand 1 – multiply
MPY
00h
16-bit operand 1 – signed multiply
MPYS
02h
16-bit operand 1 – multiply accumulate
MAC
04h
16-bit operand 1 – signed multiply accumulate
MACS
06h
16-bit operand 2
OP2
08h
16 × 16 result low word
RESLO
0Ah
16 × 16 result high word
RESHI
0Ch
16 × 16 sum extension register
SUMEXT
0Eh
32-bit operand 1 – multiply low word
MPY32L
10h
32-bit operand 1 – multiply high word
MPY32H
12h
32-bit operand 1 – signed multiply low word
MPYS32L
14h
32-bit operand 1 – signed multiply high word
MPYS32H
16h
32-bit operand 1 – multiply accumulate low word
MAC32L
18h
32-bit operand 1 – multiply accumulate high word
MAC32H
1Ah
32-bit operand 1 – signed multiply accumulate low word
MACS32L
1Ch
32-bit operand 1 – signed multiply accumulate high word
MACS32H
1Eh
32-bit operand 2 – low word
OP2L
20h
32-bit operand 2 – high word
OP2H
22h
32 × 32 result 0 – least significant word
RES0
24h
32 × 32 result 1
RES1
26h
32 × 32 result 2
RES2
28h
32 × 32 result 3 – most significant word
RES3
2Ah
MPY32 control register 0
MPY32CTL0
2Ch
Table 6-71. DMA General Control Registers (Base Address: 0500h)
REGISTER DESCRIPTION
REGISTER
OFFSET
DMA module control 0
DMACTL0
00h
DMA module control 1
DMACTL1
02h
DMA module control 2
DMACTL2
04h
DMA module control 3
DMACTL3
06h
DMA module control 4
DMACTL4
08h
DMA interrupt vector
DMAIV
0Eh
Table 6-72. DMA Channel 0 Registers (Base Address: 0500h)
REGISTER DESCRIPTION
REGISTER
OFFSET
DMA channel 0 control
DMA0CTL
10h
DMA channel 0 source address low
DMA0SAL
12h
DMA channel 0 source address high
DMA0SAH
14h
DMA channel 0 destination address low
DMA0DAL
16h
DMA channel 0 destination address high
DMA0DAH
18h
DMA channel 0 transfer size
DMA0SZ
1Ah
126
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-73. DMA Channel 1 Registers (Base Address: 0500h)
REGISTER DESCRIPTION
REGISTER
OFFSET
DMA channel 1 control
DMA1CTL
20h
DMA channel 1 source address low
DMA1SAL
22h
DMA channel 1 source address high
DMA1SAH
24h
DMA channel 1 destination address low
DMA1DAL
26h
DMA channel 1 destination address high
DMA1DAH
28h
DMA channel 1 transfer size
DMA1SZ
2Ah
Table 6-74. DMA Channel 2 Registers (Base Address: 0500h)
REGISTER DESCRIPTION
REGISTER
OFFSET
DMA channel 2 control
DMA2CTL
30h
DMA channel 2 source address low
DMA2SAL
32h
DMA channel 2 source address high
DMA2SAH
34h
DMA channel 2 destination address low
DMA2DAL
36h
DMA channel 2 destination address high
DMA2DAH
38h
DMA channel 2 transfer size
DMA2SZ
3Ah
Table 6-75. eUSCI_A0 Registers (Base Address: 05C0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
eUSCI_A control word 0
UCA0CTLW0
00h
eUSCI _A control word 1
UCA0CTLW1
02h
eUSCI_A baud rate 0
UCA0BR0
06h
eUSCI_A baud rate 1
UCA0BR1
07h
eUSCI_A modulation control
UCA0MCTLW
08h
eUSCI_A status
UCA0STAT
0Ah
eUSCI_A receive buffer
UCA0RXBUF
0Ch
eUSCI_A transmit buffer
UCA0TXBUF
0Eh
eUSCI_A LIN control
UCA0ABCTL
10h
eUSCI_A IrDA transmit control
UCA0IRTCTL
12h
eUSCI_A IrDA receive control
UCA0IRRCTL
13h
eUSCI_A interrupt enable
UCA0IE
1Ah
eUSCI_A interrupt flags
UCA0IFG
1Ch
eUSCI_A interrupt vector word
UCA0IV
1Eh
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
127
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-76. eUSCI_A1 Registers (Base Address:05E0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
eUSCI_A control word 0
UCA1CTLW0
00h
eUSCI _A control word 1
UCA1CTLW1
02h
eUSCI_A baud rate 0
UCA1BR0
06h
eUSCI_A baud rate 1
UCA1BR1
07h
eUSCI_A modulation control
UCA1MCTLW
08h
eUSCI_A status
UCA1STAT
0Ah
eUSCI_A receive buffer
UCA1RXBUF
0Ch
eUSCI_A transmit buffer
UCA1TXBUF
0Eh
eUSCI_A LIN control
UCA1ABCTL
10h
eUSCI_A IrDA transmit control
UCA1IRTCTL
12h
eUSCI_A IrDA receive control
UCA1IRRCTL
13h
eUSCI_A interrupt enable
UCA1IE
1Ah
eUSCI_A interrupt flags
UCA1IFG
1Ch
eUSCI_A interrupt vector word
UCA1IV
1Eh
Table 6-77. eUSCI_A2 Registers (Base Address:0600h)
REGISTER DESCRIPTION
REGISTER
OFFSET
eUSCI_A control word 0
UCA2CTLW0
00h
eUSCI _A control word 1
UCA2CTLW1
02h
eUSCI_A baud rate 0
UCA2BR0
06h
eUSCI_A baud rate 1
UCA2BR1
07h
eUSCI_A modulation control
UCA2MCTLW
08h
eUSCI_A status
UCA2STAT
0Ah
eUSCI_A receive buffer
UCA2RXBUF
0Ch
eUSCI_A transmit buffer
UCA2TXBUF
0Eh
eUSCI_A LIN control
UCA2ABCTL
10h
eUSCI_A IrDA transmit control
UCA2IRTCTL
12h
eUSCI_A IrDA receive control
UCA2IRRCTL
13h
eUSCI_A interrupt enable
UCA2IE
1Ah
eUSCI_A interrupt flags
UCA2IFG
1Ch
eUSCI_A interrupt vector word
UCA2IV
1Eh
128
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-78. eUSCI_B0 Registers (Base Address: 0640h)
REGISTER DESCRIPTION
REGISTER
OFFSET
eUSCI_B control word 0
UCB0CTLW0
00h
eUSCI_B control word 1
UCB0CTLW1
02h
eUSCI_B bit rate 0
UCB0BR0
06h
eUSCI_B bit rate 1
UCB0BR1
07h
eUSCI_B status word
UCB0STATW
08h
eUSCI_B byte counter threshold
UCB0TBCNT
0Ah
eUSCI_B receive buffer
UCB0RXBUF
0Ch
eUSCI_B transmit buffer
UCB0TXBUF
0Eh
eUSCI_B I2C own address 0
UCB0I2COA0
14h
eUSCI_B I2C own address 1
UCB0I2COA1
16h
eUSCI_B I2C own address 2
UCB0I2COA2
18h
eUSCI_B I2C own address 3
UCB0I2COA3
1Ah
eUSCI_B received address
UCB0ADDRX
1Ch
eUSCI_B address mask
UCB0ADDMASK
1Eh
eUSCI I2C slave address
UCB0I2CSA
20h
eUSCI interrupt enable
UCB0IE
2Ah
eUSCI interrupt flags
UCB0IFG
2Ch
eUSCI interrupt vector word
UCB0IV
2Eh
Table 6-79. ADC10_A Registers (Base Address: 0740h)
REGISTER DESCRIPTION
REGISTER
OFFSET
ADC10_A control register 0
ADC10CTL0
00h
ADC10_A control register 1
ADC10CTL1
02h
ADC10_A control register 2
ADC10CTL2
04h
ADC10_A window comparator low threshold
ADC10LO
06h
ADC10_A window comparator high threshold
ADC10HI
08h
ADC10_A memory control register 0
ADC10MCTL0
0Ah
ADC10_A conversion memory register
ADC10MCTL0
12h
ADC10_A interrupt enable
ADC10IE
1Ah
ADC10_A interrupt flags
ADC10IGH
1Ch
ADC10_A interrupt vector word
ADC10IV
1Eh
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
129
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
Table 6-80. SD24_B Registers (Base Address: 0800h)
REGISTER DESCRIPTION
REGISTER
OFFSET
SD24_B control 0 register
SD24BCTL0
00h
SD24_B control 1 register
SD24BCTL1
02h
SD24_B interrupt flag register
SD24BIFG
0Ah
SD24_B interrupt enable register
SD24BIE
0Ch
SD24_B interrupt vector register
SD24BIV
0Eh
SD24_B converter 0 control register
SD24BCCTL0
10h
SD24_B converter 0 input control register
SD24BINCTL0
12h
SD24_B converter 0 OSR control register
SD24BOSR0
14h
SD24_B converter 0 preload register
SD24BPRE0
16h
SD24_B converter 1 control register
SD24BCCTL1
18h
SD24_B converter 1 input control register
SD24BINCTL1
1Ah
SD24_B converter 1 OSR control register
SD24BOSR1
1Ch
SD24_B converter 1 preload register
SD24BPRE1
1Eh
SD24_B converter 2 control register
SD24BCCTL2
20h
SD24_B converter 2 input control register
SD24BINCTL2
22h
SD24_B converter 2 OSR control register
SD24BOSR2
24h
SD24_B converter 2 preload register
SD24BPRE2
26h
SD24_B converter 0 conversion memory low word register
SD24BMEML0
50h
SD24_B converter 0 conversion memory high word register
SD24BMEMH0
52h
SD24_B converter 1 conversion memory low word register
SD24BMEML1
54h
SD24_B converter 1 conversion memory high word register
SD24BMEMH1
56h
SD24_B converter 2 conversion memory low word register
SD24BMEML2
58h
SD24_B converter 2 conversion memory high word register
SD24BMEMH2
5Ah
Table 6-81. Auxiliary Supplies Registers (Base Address: 09E0h)
REGISTER DESCRIPTION
REGISTER
OFFSET
Auxiliary supply control 0 register
AUXCTL0
00h
Auxiliary supply control 1 register
AUXCTL1
02h
Auxiliary supply control 2 register
AUXCTL2
04h
AUX2 charger control
AUX2CHCTL
12h
AUX3 charger control
AUX3CHCTL
14h
AUX ADC control
AUXADCCTL
16h
AUX interrupt flag
AUXIFG
1Ah
AUX interrupt enable
AUXIE
1Ch
AUX interrupt vector word
AUXIV
1Eh
130
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
Table 6-82. LCD_C Registers (Base Address: 0A00h)
REGISTER DESCRIPTION
REGISTER
OFFSET
LCD_C control register 0
LCDCCTL0
000h
LCD_C control register 1
LCDCCTL1
002h
LCD_C blinking control register
LCDCBLKCTL
004h
LCD_C memory control register
LCDCMEMCTL
006h
LCD_C voltage control register
LCDCVCTL
008h
LCD_C port control 0
LCDCPCTL0
00Ah
LCD_C port control 1
LCDCPCTL1
00Ch
LCD_C port control 2
LCDCPCTL2
00Eh
LCD_C charge pump control register
LCDCCPCTL
012h
LCD_C interrupt vector
LCDCIV
01Eh
LCD_C memory 1
LCDM1
020h
LCD_C memory 2
LCDM2
021h
Static and 2 to 4 mux modes
⋮
⋮
⋮
LCD_C memory 20
LCDM20
033h
LCD_C blinking memory 1
LCDBM1
040h
LCD_C blinking memory 2
LCDBM2
041h
⋮
⋮
LCD_C blinking memory 20
⋮
LCDBM20
053h
LCD_C memory 1
LCDM1
020h
LCD_C memory 2
LCDM2
021h
5 to 8 mux modes
⋮
⋮
LCD_C memory 40
LCDM40
⋮
047h
Detailed Description
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
131
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
6.14 Identification
6.14.1 Revision Identification
The device revision information is shown as part of the top-side marking on the device package. The
device-specific erratasheet describes these markings. For links to all of the erratasheets for the devices in
this data sheet, see Section 8.2.
The hardware revision is also stored in the Device Descriptor structure in the Info Block section. For
details on this value, see the "Hardware Revision" entries in Section 6.12.
6.14.2 Device Identification
The device type can be identified from the top-side marking on the device package. The device-specific
erratasheet describes these markings. For links to all of the erratasheets for the devices in this data sheet,
see Section 8.2.
A device identification value is also stored in the Device Descriptor structure in the Info Block section. For
details on this value, see the "Device ID" entries in Section 6.12.
6.14.3 JTAG Identification
Programming through the JTAG interface, including reading and identifying the JTAG ID, is described in
detail in the MSP430 Programming Via the JTAG Interface User's Guide (SLAU320).
132
Detailed Description
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
7 Applications, Implementation, and Layout
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
The following resources provide application guidelines and best practices when designing with the
MSP430F673xA and MSP430F672xA.
Implementation of a Single-Phase Electronic Watt-Hour Meter Using the MSP430F6736(A)
(SLAA517)
This application report describes the implementation of a single-phase electronic electricity meter using
the Texas Instruments MSP430F673x(A) metering processor. It also includes the necessary information
with regard to metrology software and hardware procedures for this single-chip implementation.
High Accuracy Single-Phase Electricity Meter With Tamper Detection (TIDM-SINGLEPHASEMETER)
This design, featuring the MSP430F6736(A) device, implements a highly-integrated single-chip electricity
metering (e-meter) solution. Hardware and software design files are provided to enable calculation of
various parameters for single phase energy measurement, such as RMS current & voltage, active and
reactive power and energies, power-factor and frequency.
Features
• Low-power single-phase e-metering implementation
• Calculate parameters such as RMS current & voltage, active and reactive power and energies, power
factor & frequency
• Based on the highly-integrated MSP430F67xx(A) family of metering-focused MCU SoCs
• Segmented LCD is also implemented in this design
• RF modules can also be added to this design to enable unique connectivity solutions.
Applications, Implementation, and Layout
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
133
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
8 Device and Documentation Support
8.1
Device Support
8.1.1
Getting Started and Next Steps
For more information on the MSP430™ family of devices and the tools and libraries that are available to
help with your development, visit the Getting Started page.
8.1.2
Development Tools Support
All MSP430™ microcontrollers are supported by a wide variety of software and hardware development
tools. Tools are available from TI and various third parties. See them all at www.ti.com/msp430tools.
8.1.2.1
Hardware Features
See the Code Composer Studio for MSP430 User's Guide(SLAU157) for details on the available features.
MSP430
Architecture
4-Wire
JTAG
2-Wire
JTAG
Breakpoints
(N)
Range
Breakpoints
Clock
Control
State
Sequencer
Trace
Buffer
LPMx.5
Debugging
Support
MSP430Xv2
Yes
Yes
3
Yes
Yes
No
No
No
8.1.2.2
Recommended Hardware Options
8.1.2.2.1 Target Socket Boards
The target socket boards allow easy programming and debugging of the device using JTAG. They also
feature header pin outs for prototyping. Target socket boards are orderable individually or as a kit with the
JTAG programmer and debugger included. The following table shows the compatible target boards and
the supported packages.
Package
Target Board and Programmer Bundle
Target Board Only
100-pin LQFP (PZ)
MSP-FET430U100B
MSP-TS430PZ100B
8.1.2.2.2 Experimenter Boards
Experimenter Boards and Evaluation kits are available for some MSP430 devices. These kits feature
additional hardware components and connectivity for full system evaluation and prototyping. See
www.ti.com/msp430tools for details.
8.1.2.2.3 Debugging and Programming Tools
Hardware programming and debugging tools are available from TI and from its third party suppliers. See
the full list of available tools at www.ti.com/msp430tools.
8.1.2.2.4 Production Programmers
The production programmers expedite loading firmware to devices by programming several devices
simultaneously.
Part Number
PC Port
MSP-GANG
Serial and USB
8.1.2.3
Features
Provider
Program up to eight devices at a time. Works with PC or standalone.
Texas Instruments
Recommended Software Options
8.1.2.3.1 Integrated Development Environments
Software development tools are available from TI or from third parties. Open source solutions are also
available.
This device is supported by Code Composer Studio™ IDE (CCS).
134
Device and Documentation Support
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
SLASE46 – FEBRUARY 2015
8.1.2.3.2 MSP430Ware
MSP430Ware is a collection of code examples, data sheets, and other design resources for all MSP430
devices delivered in a convenient package. In addition to providing a complete collection of existing
MSP430 design resources, MSP430Ware also includes a high-level API called MSP430 Driver Library.
This library makes it easy to program MSP430 hardware. MSP430Ware is available as a component of
CCS or as a standalone package.
8.1.2.3.3 Command-Line Programmer
MSP430 Flasher is an open-source, shell-based interface for programming MSP430 microcontrollers
through a FET programmer or eZ430 using JTAG or Spy-Bi-Wire (SBW) communication. MSP430 Flasher
can be used to download binary files (.txt or .hex) files directly to the MSP430 microcontroller without the
need for an IDE.
8.1.3
Device and Development Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
MSP430 MCU devices and support tools. Each MSP430 MCU commercial family member has one of
three prefixes: MSP, PMS, or XMS (for example, MSP430F5259). Texas Instruments recommends two of
three possible prefix designators for its support tools: MSP and MSPX. These prefixes represent
evolutionary stages of product development from engineering prototypes (with XMS for devices and MSPX
for tools) through fully qualified production devices and tools (with MSP for devices and MSP for tools).
Device development evolutionary flow:
XMS – Experimental device that is not necessarily representative of the final device's electrical
specifications
PMS – Final silicon die that conforms to the device's electrical specifications but has not completed quality
and reliability verification
MSP – Fully qualified production device
Support tool development evolutionary flow:
MSPX – Development-support product that has not yet completed Texas Instruments internal qualification
testing.
MSP – Fully-qualified development-support product
XMS and PMS devices and MSPX development-support tools are shipped against the following
disclaimer:
"Developmental product is intended for internal evaluation purposes."
MSP devices and MSP development-support tools have been characterized fully, and the quality and
reliability of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (XMS and PMS) have a greater failure rate than the standard
production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are
to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the
package type (for example, PZP) and temperature range (for example, T). Figure 8-1 provides a legend
for reading the complete device name for any family member.
Device and Documentation Support
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
135
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
www.ti.com
MSP 430 F 5 438 A I ZQW T XX
Processor Family
Optional: Additional Features
430 MCU Platform
Optional: Tape and Reel
Device Type
Packaging
Series
Feature Set
Processor Family
430 MCU Platform
Optional: Temperature Range
Optional: A = Revision
CC = Embedded RF Radio
MSP = Mixed Signal Processor
XMS = Experimental Silicon
PMS = Prototype Device
TI’s Low Power Microcontroller Platform
Device Type
Memory Type
C = ROM
F = Flash
FR = FRAM
G = Flash or FRAM (Value Line)
L = No Nonvolatile Memory
Specialized Application
AFE = Analog Front End
BT = Preprogrammed with Bluetooth
BQ = Contactless Power
CG = ROM Medical
FE = Flash Energy Meter
FG = Flash Medical
FW = Flash Electronic Flow Meter
Series
1 Series = Up to 8 MHz
2 Series = Up to 16 MHz
3 Series = Legacy
4 Series = Up to 16 MHz w/ LCD
5 Series = Up to 25 MHz
6 Series = Up to 25 MHz w/ LCD
0 = Low Voltage Series
Feature Set
Various Levels of Integration Within a Series
Optional: A = Revision
N/A
Optional: Temperature Range S = 0°C to 50°C
C = 0°C to 70°C
I = –40°C to 85°C
T = –40°C to 105°C
Packaging
http://www.ti.com/packaging
Optional: Tape and Reel
T = Small Reel
R = Large Reel
No Markings = Tube or Tray
Optional: Additional Features -EP = Enhanced Product (–40°C to 105°C)
-HT = Extreme Temperature Parts (–55°C to 150°C)
-Q1 = Automotive Q100 Qualified
Figure 8-1. Device Nomenclature
136
Device and Documentation Support
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
8.2
SLASE46 – FEBRUARY 2015
Documentation Support
The following documents describe the MSP430F673xA and MSP430F672xA devices. Copies of these
documents are available on the Internet at www.ti.com.
SLAU208
MSP430x5xx and MSP430x6xx Family User's Guide. Detailed information on the modules
and peripherals available in this device family.
SLAZ646
MSP430F6736A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ647
MSP430F6735A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ648
MSP430F6734A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ649
MSP430F6733A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ650
MSP430F6731A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ651
MSP430F6730A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ652
MSP430F6726A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ653
MSP430F6725A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ654
MSP430F6724A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ655
MSP430F6723A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ656
MSP430F6721A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
SLAZ657
MSP430F6720A Device Erratasheet. Describes the known exceptions to the functional
specifications for this device.
Device and Documentation Support
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
137
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
SLASE46 – FEBRUARY 2015
8.3
www.ti.com
Related Links
Table 8-1 lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 8-1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
MSP430F6736A
Click here
Click here
Click here
Click here
Click here
MSP430F6735A
Click here
Click here
Click here
Click here
Click here
MSP430F6734A
Click here
Click here
Click here
Click here
Click here
MSP430F6733A
Click here
Click here
Click here
Click here
Click here
MSP430F6731A
Click here
Click here
Click here
Click here
Click here
MSP430F6730A
Click here
Click here
Click here
Click here
Click here
MSP430F6726A
Click here
Click here
Click here
Click here
Click here
MSP430F6725A
Click here
Click here
Click here
Click here
Click here
MSP430F6724A
Click here
Click here
Click here
Click here
Click here
MSP430F6723A
Click here
Click here
Click here
Click here
Click here
MSP430F6721A
Click here
Click here
Click here
Click here
Click here
MSP430F6720A
Click here
Click here
Click here
Click here
Click here
8.4
Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the
respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views;
see TI's Terms of Use.
TI E2E™ Community
TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At
e2e.ti.com, you can ask questions, share knowledge, explore ideas, and help solve problems with fellow
engineers.
TI Embedded Processors Wiki
Texas Instruments Embedded Processors Wiki. Established to help developers get started with embedded
processors from Texas Instruments and to foster innovation and growth of general knowledge about the
hardware and software surrounding these devices.
8.5
Trademarks
MSP430, Code Composer Studio, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
8.6
Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
8.7
Export Control Notice
Recipient agrees to not knowingly export or re-export, directly or indirectly, any product or technical data
(as defined by the U.S., EU, and other Export Administration Regulations) including software, or any
controlled product restricted by other applicable national regulations, received from disclosing party under
nondisclosure obligations (if any), or any direct product of such technology, to any destination to which
such export or re-export is restricted or prohibited by U.S. or other applicable laws, without obtaining prior
authorization from U.S. Department of Commerce and other competent Government authorities to the
extent required by those laws.
138
Device and Documentation Support
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
MSP430F6736A, MSP430F6735A, MSP430F6734A, MSP430F6733A
MSP430F6731A, MSP430F6730A, MSP430F6726A, MSP430F6725A
MSP430F6724A, MSP430F6723A, MSP430F6721A, MSP430F6720A
www.ti.com
8.8
SLASE46 – FEBRUARY 2015
Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
9 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the
most current data available for the designated devices. This data is subject to change without notice and
revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Mechanical, Packaging, and Orderable Information
Submit Documentation Feedback
Product Folder Links: MSP430F6736A MSP430F6735A MSP430F6734A MSP430F6733A MSP430F6731A
MSP430F6730A MSP430F6726A MSP430F6725A MSP430F6724A MSP430F6723A MSP430F6721A
MSP430F6720A
Copyright © 2015, Texas Instruments Incorporated
139
PACKAGE OPTION ADDENDUM
www.ti.com
8-Mar-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
MSP430F6720AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6720A
MSP430F6720AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6720A
MSP430F6720AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6720A
MSP430F6720AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6720A
MSP430F6721AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6721A
MSP430F6721AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6721A
MSP430F6721AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6721A
MSP430F6721AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6721A
MSP430F6723AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6723A
MSP430F6723AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6723A
MSP430F6723AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6723A
MSP430F6723AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6723A
MSP430F6724AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6724A
MSP430F6724AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6724A
MSP430F6724AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6724A
MSP430F6724AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6724A
MSP430F6725AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6725A
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
8-Mar-2015
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
MSP430F6725AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6725A
MSP430F6725AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6725A
MSP430F6725AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6725A
MSP430F6726AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6726A
MSP430F6726AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6726A
MSP430F6726AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6726A
MSP430F6726AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6726A
MSP430F6730AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6730A
MSP430F6730AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6730A
MSP430F6730AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6730A
MSP430F6730AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6730A
MSP430F6731AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6731A
MSP430F6731AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6731A
MSP430F6731AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6731A
MSP430F6731AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6731A
MSP430F6733AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6733A
MSP430F6733AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6733A
MSP430F6733AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6733A
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
8-Mar-2015
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
MSP430F6733AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6733A
MSP430F6734AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6734A
MSP430F6734AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6734A
MSP430F6734AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6734A
MSP430F6734AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6734A
MSP430F6735AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6735A
MSP430F6735AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6735A
MSP430F6735AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6735A
MSP430F6735AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6735A
MSP430F6736AIPN
ACTIVE
LQFP
PN
80
119
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6736A
MSP430F6736AIPNR
ACTIVE
LQFP
PN
80
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6736A
MSP430F6736AIPZ
ACTIVE
LQFP
PZ
100
90
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6736A
MSP430F6736AIPZR
ACTIVE
LQFP
PZ
100
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
F6736A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Mar-2015
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Mar-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
MSP430F6720AIPNR
LQFP
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6720AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6721AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6721AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6723AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6723AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6724AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6724AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6725AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6725AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6726AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6726AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6730AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6730AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6731AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6731AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6733AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6733AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Mar-2015
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
MSP430F6734AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6734AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6735AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6735AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
MSP430F6736AIPNR
LQFP
PN
80
1000
330.0
24.4
15.0
15.0
2.1
20.0
24.0
Q2
MSP430F6736AIPZR
LQFP
PZ
100
1000
330.0
24.4
17.0
17.0
2.1
20.0
24.0
Q2
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MSP430F6720AIPNR
LQFP
MSP430F6720AIPZR
LQFP
PN
80
1000
367.0
367.0
45.0
PZ
100
1000
367.0
367.0
45.0
MSP430F6721AIPNR
LQFP
MSP430F6721AIPZR
LQFP
PN
80
1000
367.0
367.0
45.0
PZ
100
1000
367.0
367.0
MSP430F6723AIPNR
LQFP
45.0
PN
80
1000
367.0
367.0
45.0
MSP430F6723AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6724AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6724AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6725AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6725AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6726AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Mar-2015
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MSP430F6726AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6730AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6730AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6731AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6731AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6733AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6733AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6734AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6734AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6735AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6735AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
MSP430F6736AIPNR
LQFP
PN
80
1000
367.0
367.0
45.0
MSP430F6736AIPZR
LQFP
PZ
100
1000
367.0
367.0
45.0
Pack Materials-Page 3
MECHANICAL DATA
MTQF010A – JANUARY 1995 – REVISED DECEMBER 1996
PN (S-PQFP-G80)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
0,08 M
41
60
61
40
80
21
0,13 NOM
1
20
Gage Plane
9,50 TYP
12,20
SQ
11,80
14,20
SQ
13,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040135 / B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MTQF013A – OCTOBER 1994 – REVISED DECEMBER 1996
PZ (S-PQFP-G100)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
75
0,08 M
51
76
50
100
26
1
0,13 NOM
25
12,00 TYP
Gage Plane
14,20
SQ
13,80
16,20
SQ
15,80
0,05 MIN
1,45
1,35
0,25
0°– 7°
0,75
0,45
Seating Plane
0,08
1,60 MAX
4040149 /B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated