Ordering number : ENA0896A LV7150V Bi-CMOS IC Switch for the Wideband Video Signal (with LPF) Overview The LV7150V is switch for the wideband video signal. It has the two input switches by three channels. It built in the 6MHz/12MHz/30MHz-LPF. It is the best for the filter to remove the digital clock noise of the Y/Pb/Pr or RGB Analog video signal before the A/D converter. It can correspond to the full HD signal because it provides the flat frequency response to 60MHz. Functions • Two input switches × three channels • Y/Pb/Pr and RGB signal inputs • Flat frequency response to 60MHz (Bypass filter) • 6MHz/12MHz/30MHz-LPF Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Pd max Unit 6 Ta≤75°C Mounted on a specified board * 300 V mW Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +125 °C Note *: Mounted on a specified board: 114.3mm×76.1mm×1.6mm glass epoxy Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. D1907 TI IM 20071127-S00006 / 72507 TI IM No.A0896-1/7 LV7150V Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommended supply voltage Conditions Ratings Unit VCC Operating supply voltage Range VCC opg 5 V 4.75 to 5.25 V Electrical Characteristics at Ta = 25°C, VCC = 5.0V Parameter Input signal Input Point Signal Freq Out Mag Ratings Test Condition Point min typ unit max VCC supply current & Internal reference regulator VCC supply current At non-signal, The current V3 26 34 42 mA 2.8 3.0 3.2 V -0.5 -0.2 0.0 dB -3.0 -1.0 1.0 dB -3.0 0.0 1.0 dB -30.0 -20.0 dB 0.0 1.0 dB -30.0 -20.0 dB -1.0 0.0 1.0 dB -3.5 -1.0 1.5 dB -45.0 -33.0 dB -60.0 -50.0 dB -60.0 -55.0 dB flows to 3pin Internal reference T16 regulator voltage The voltage of 16pin Voltage gain Voltage gain Py/Pb/Pr R/G/B T1A T2A T4A T5A T15 SIG2 100k 300mVpp T7A T8A Output gain for input T13 T11 Frequency response Frequency response at LPF_Through Frequency response 1 at 6MHz_LPF Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Frequency response 2 at 6MHz _LPF Frequency response 1 at 12MHz_LPF Frequency response 2 at 12MHz_LPF Frequency response 1 at 30MHz_LPF Frequency response 2 at 30MHz_LPF Frequency response 3 at 30MHz_LPF Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B Py/Pb/Pr R/G/B T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A 60M 100k 6M 100k 13.5M 100k 12M 100k 27M 100k 20M 100k 30M 100k 74M 100k 300mVpp 300mVpp T15 LPF_Through is selected, T13 Output gain difference T11 between 100kHz and 60MHz T15 6MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 6MHz T15 300mVpp T13 T11 300mVpp 300mVpp 300mVpp 300mVpp 300mVpp 6MHz_LPF is selected, Output gain difference between 100kHz and 13.5MHz T15 12MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 12MHz T15 12MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 27MHz T15 30MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 20MHz T15 30MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 30MHz T15 30MHz_LPF is selected, T13 Output gain difference T11 between 100kHz and 74MHz -3.0 S/N S/N ratio Py at 30MHz_LPF R G B T1A T2A T4A T5A SIG1 T7A T8A 30M 100k T15 650mVpp T13 T11 30MHz_LPF is selected, The S/N ratio from 100kHz to 30MHz Crosstalk Crosstalk Py/Pb/Pr R/G/B T1A T2A T4A T5A T7A T8A SIG2 5M 700mVpp T15 The ratio of the output leak of T13 the non-selection input T11 Continued on next page. No.A0896-2/7 LV7150V Continued from preceding page. Parameter Input signal Input Point Signal Freq Out Mag Ratings Test Condition Point min typ unit max Group delay Group delay Py/Pb/Pr at LPF_Through R/G/B Group delay Py/Pb/Pr at 6MHz_LPF R/G/B Group delay Py/Pb/Pr at 12MHz_LPF R/G/B Group delay Py/Pb/Pr at 30MHz_LPF R/G/B T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A T1A T2A T4A T5A SIG2 T7A T8A 60M 100k 6M 100k 12M 100k 30M 100k 300mVpp 300mVpp 300mVpp 300mVpp T15 LPF_Through is selected, T13 Delay difference between T11 100kHz and 60MHz T15 6MHz_LPF is selected, T13 Delay difference between T11 100kHz and 6MHz T15 12MHz_LPF is selected, T13 Delay difference between T11 100kHz and 12MHz T15 30MHz_LPF is selected, T13 Delay difference between T11 100kHz and 30MHz 0.5 2.0 ns 40.0 70.0 ns 20.0 40.0 ns 10.0 20.0 ns Package Dimensions unit : mm (typ) 3178B 5.2 0.5 6.4 9 4.4 16 1 8 0.65 0.15 (0.33) 0.1 (1.3) 1.5max 0.22 SANYO : SSOP16(225mil) Pin Control Table Pin Control Table SW No. Pin No. SW function name SW1 Pin12 CLAMP/BIAS_CTL SW2 Pin10 Filter_CTL1 SW3 Pin9 Filter_CTL2 SW4 Pin14 Input_Select_CTL Input Control Table CLAMP/BIAS_CTL Mode selected Low (0 to 0.7V) CLAMP (Y/Pb/Pr_Mode) High (2.3V to VCC) BIAS (RGB_Mode) Continued on next page. No.A0896-3/7 LV7150V Continued from preceding page. Filter Control Table Filter_CTL1 Filter_CTL2 Mode selected Low (0 to 0.7V) Low (0 to 0.7V) 6Mz_LPF Low (0 to 0.7V) High (2.3V to VCC) 12Mz_LPF High (2.3V to VCC) Low (0 to 0.7V) 30Mz_LPF High (2.3V to VCC) High (2.3V to VCC) LPF_Through Input Select Control Table Input_Select_CTL Mode selected Low (0 to 0.7V) CH1_select High (2.3V to VCC) CH2_select Block Diagram Pr/R_IN1 Pr/R_IN2 1 F + 1 F + 1 2 BIAS 100k SW4: Input_Select _CTL VREG_3V 16 6MHz LPF 12MHz LPF BIAS 100k 1 F + BUF 30MHz LPF 15 10 F + Pr/R_OUT SW2&SW3: Filter_CTL Through VCC 3 14 SW4:Input_Select_CTL 6MHz LPF Py/G_IN1 Py/G_IN2 1 F + 1 F + 12MHz LPF CLAMP 4 BUF BIAS 100k SW4: Input_Select _CTL CLAMP 5 BIAS 100k 30MHz LPF SW1: CLAMP/BIAS_ CTL SW1: CLAMP/BIAS_ CTL 13 Py/G_OUT SW2&SW3: Filter_CTL Through 12 SW1:CLAMP/BIAS_CTL 6MHz LPF 12MHz LPF GND 10 F + 6 BUF 30MHz LPF 11 10 F + Pb/B_OUT SW2&SW3: Filter_CTL Through Pb/B_IN1 Pb/B_IN2 1 F + 1 F + 7 BIAS 100k 8 BIAS 100k 10 SW2:Filter_CTL1 9 SW3:Filter_CTL2 SW4: Input_Select_CTL No.A0896-4/7 LV7150V Pin Function Pin No. Pin name DC voltage P1 Pr/R_IN1 2.3V P2 Pr/R_IN2 2.3V P3 VCC P4 Py/G_IN1 Signal wave form Input/Output form Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) P5 Py/G_IN2 Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) P6 GND P7 Pb/B_IN1 2.3V Continued on next page. No.A0896-5/7 LV7150V Continued from preceding page. Pin No. Pin name DC voltage P8 Pb/RB_IN2 2.3V P9 Filter_CTL2 High: 2.3 to VCC Low: 0 to 0.7V P10 Filter_CTL1 High: 2.3 to VCC Low: 0 to 0.7V P11 Pb/B_OUT 2.3V Signal wave form Input/Output form 200 50 11 200 P12 CLP/BIAS_CTL High: 2.3 to VCC RGB (Bias) Low: 0 to 0.7V Y/Pb/Pr (Clamp) P13 Py/G_OUT Y/Pb/Pr: 1.8V (Clamp) RGB: 2.3V (Bias) Continued on next page. No.A0896-6/7 LV7150V Continued from preceding page. Pin No. Pin name P14 Input_Select_CTL DC voltage Signal wave form Input/Output form High: 2.3 to VCC Ch2 Low: 0 to 0.7V Ch1 P15 Pr/R_OUT 2.3V P16 REG3V 3.0V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of December, 2007. Specifications and information herein are subject to change without notice. PS No.A0896-7/7