HCC4051B/52B/53B HCF4051B/52B/53B ANALOG MULTIPLEXERS-DEMULTIPLEXERS 4051B - SINGLE 8-CHANNEL 4052B - DIFFERENTIAL 4-CHANNEL 4053B - TRIPLE 2-CHANNEL . . . .. . . .. .. QUIESCENT CURRENT SPECIFIED TO 20V FOR HCC DEVICE LOW ”ON” RESISTANCE : 125Ω (typ.) OVER 15V p.p. SIGNAL-INPUT RANGE FOR VDDVEE = 15V HIGH ”OFF” RESISTANCE : CHANNEL LEAKAGE ± 100pA (typ.) VDD – VEE = 18V BINARY ADDRESS DECODING ON CHIP VERY LOW QUIESCENT POWER DISSIPATION UNDER ALL DIGITAL CONTROL INPUT AND SUPPLY CONDITIONS : 0.2 µW (typ.), VDD – VSS = VDD – VEE = 10V MATCHED SWITCH CHARACTERISTICS : RON = 5Ω (typ.) for VDD – VEE = 15V WIDE RANGE OF DIGITAL AND ANALOG SIGNAL LEVELS : DIGITAL 3 TO 20V, ANALOG TO 20V p.p. 5V, 10V, AND 15V PARAMETRIC RATINGS INPUT CURRENT OF 100mA AT 18V AND 25°C FOR HCC DEVICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TENo TATIVE STANDARD N 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF ”B” SERIES CMOS DEVICES” EY (Plastic Package) M1 (Micro Package) F (Ceramic Frit Seal Package) C1 (Plastic Chip Carrier) ORDER CODES : HCC40XXBF HCF40XXBM1 HCF40XXBEY HCF40XXBC1 DESCRIPTION The HCC 4051B, 4052B and 4053B (extended temperature range) and HCF4051B, 4052B and 4053B (intermediate temperature range) are monolithic integrated circuits, available in 16-lead dual in-line plastic or ceramic package and plastic micropackage. HCC/HCF4051B, HCC/HCF4052B, and HCC/HCF4053B analog multiplexers/demultiplexers are digitally controlled analog switches having low ON impedance and very low OFF leakage PIN CONNECTIONS 4051B June 1989 4052B 4053B 1/17 HCC/HCF4051B/52B/53B current. These multiplexer circuits dissipate extremely low quiescent power over the full VDD – VSS and VDD – VEE supply-voltage ranges, independent of the logic state of the control signals. When a-logic ”1” is present at the inhibit input terminal all channel are off. The HCC/HCF4051B is a single 8-channel multiplexer having three binary control inputs, A, B, and C, and an inhibit input. The three binary signals select 1 of 8 channels to be turned on, and connect one of the 8 inputs to the output. The HCC/HCF4052B is a differential 4-channel multi- plexer having two binary control inputs, A and B, and an inhibit input. The two binary input signals select 1 of 4 pairs of channels to be turned on and connect the analog inputs to the outputs. The HCC/HCF4053B is a triple 2-channel multiplexer having three separate digital control inputs, A, B, and C, and an inhibit input. Each control input selects one of a pair of channels which are connected in a singlepole double-throw configuration. FUNCTIONAL DIAGRAMS AND TRUTH TABLES 4051B Input States ”On” Channel (S) Inhibit C B A 0 0 0 0 0 0 0 0 1 1 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 0 1 0 1 5 0 1 1 0 6 0 1 1 1 7 1 X X X None 4052B 2/17 Inhibit B A 0 0 0 0x, 0y 0 0 1 1x, 1y 0 1 0 2x, 2y 0 1 1 3x, 3y 1 X X None HCC/HCF4051B/52B/53B FUNCTIONAL DIAGRAMS AND TRUTH TABLES (continued) 4053 Inhibit A or B or C 0 0 ax or bx or cx 0 1 ay or by or cy 1 X None X = Don’t care. ABSOLUTE MAXIMUM RATINGS Symbol V DD* Parameter Supply Voltage : HC C Types H C F Types Vi Input Voltage II Value Unit – 0.5 to + 20 – 0.5 to + 18 V V – 0.5 to V DD + 0.5 V DC Input Current (any one input) ± 10 mA Pt ot Total Power Dissipation (per package) Dissipation per Output Transistor for T o p = Full Package-temperature Range 200 mW 100 mW Top Operating Temperature : HCC Types H CF Types – 55 to + 125 – 40 to + 85 °C °C Tstg Storage Temperature – 65 to + 150 °C Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. * All voltage values are referred to VSS pin voltage. RECOMMENDED OPERATING CONDITIONS Symbol V DD VI Top Parameter Supply Voltage : HC C Types H C F Types Input Voltage Operating Temperature : H CC Types H C F Types Value Unit 3 to 18 3 to 15 V V 0 to V DD V – 55 to + 125 – 40 to + 85 °C °C 3/17 HCC/HCF4051B/52B/53B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Symbol IL Parameter Quiescent Device Current HCC Types HCF Types SWITCH ON Resistance HCC Types Test Conditions V EE V SS V DD V IS (V) (V) (V) (V) 5 10 15 20 5 10 15 0 ≤ VI ≤ V DD 0 ≤ VI HCF ≤ V DD Types ∆ON Resistance ∆RON (between any 2 channels) OFF (•) Any HCC Channel Channel Types Leakage OFF Current All Channels HCC OFF Types (common OUT/IN) Any HCF Channel Types OFF All Channels HCF OFF Types (common OUT/IN) C Input Capaci- Output 4051 Output 4052 tance Output 4053 Feedthrough CONTROL (Address or Inhibit) VIL Input Low Voltage = V DD Thru 1KΩ VIH IIH, IIL CI Input High Voltage Input Leakage Current Value T Lo w* 2 5 °C T High* Min. Max. Min. Typ. Max. Min. Max. 5 0.04 5 150 10 0.04 10 300 20 0.04 20 600 100 0.08 100 3000 20 0.04 20 150 40 0.04 40 300 80 0.04 80 600 5 10 15 5 10 15 5 10 15 880 310 220 880 330 230 0 18 0 0 0 0 1050 400 280 1050 400 280 100 ± 0.1 100 1000 nA 18 100 ± 0.1 100 1000 nA 0 15 300 ± 0.1 300 1000 nA 0 15 300 ± 0.1 300 1000 nA 0 0 0 0 0 0 – 5 – 5 5 VEE = V SS RL = 1KΩ to V SS IIS < 2µA (on all off channels) VI = 0/18V 5 10 15 5 10 15 HCC 18 Types HCF VI = 0/15V 15 Types Input Capacitance Any Address or Inhibit Input 1.5 3 4 3.5 7 11 pF 1.5 3 4 3.5 7 11 1.5 3 4 3.5 7 11 ±10–3 ± 0.1 ± 1 ± 0.3 ±10–3 ± 0.3 ± 1 7.5 V V ± 0.1 5 Ω Ω 5 30 18 9 0.2 ( •) Determined by minimum feasible leakage measurement for automatic testing. (*) TLow = – 55°C for HCC device : – 40°C for HCF device. (*) THigh = + 125°C for HCC device : + 85°C for HCF device. 4/17 µA 470 180 125 470 180 125 10 10 5 0 1200 580 400 1200 520 360 Unit µA pF HCC/HCF4051B/52B/53B DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, CL = 50pF all input square wave rise and fall time = 20ns) Parameter V EE R L fi V IS (V) (kΩ) (kHz) (V) SWITCH t p d Propagation Delay Time (signal input to output) Frequency Response Channel ”ON” (sine wave input) Vo at 20 Log __ = – 3dB VI Feedthrough (all channels OFF) Vo at 20 Log __ = – 40dB VI = VS S 200 10 __V _I I_ 1 5 (•) 5 10 15 10 V o at Common OUT/IN Value Typ. Max. 4053B 4052B 4051B V o at any Channel = VS S Frequency Signal Crosstalk Vo = VS S at 20 Log __ = – 40dB VI 1 5 (•) 1 = VS S 10 10 10 CONTROL (Address or Inhibit) Progation Delay Time : 0 Address-to Signal OUT 0 Channels ON or OFF 0 – 5 Propagation Delay Time : 0 Inhibit to Signal OUT 0 10 (channel turning ON) 0 – 10 Propagation Delay Time : 0 Inhibit to Signal OUT 0 0.3 (channel turning OFF) 0 – 10 Address or Inhibit to Signal 0 10* Crosstalk Sine Wave Distortion f i s = 1kHz Sine Wave Test Conditions V S S V DD (V) (V) 10 5 (•) 1 1 1 5 10 15 8 10 12 V o at any Channel 8 Between any 2 Channels 3 Between Sections measured 6 4052B only on common measured 10 on any channel Between any 2 in Pin 2 2.5 Sections 4053B out Pin 14 only in Pin 15 6 out Pin 14 0.3 0.2 0.12 5 10 15 5 5 10 15 5 5 10 15 5 360 160 120 225 360 160 120 200 200 90 70 130 10 2 (•) 3 (•) 5 (•) 0 0 0 0 0 0 0 0 0 10 V o at Common OUT/IN 30 15 11 30 25 20 60 30 60 20 65 ns MHz 4053 4052 4051 V C = V DD –V SS (square wave) Unit MHz MHz MHz % 720 320 240 450 720 320 240 400 450 210 160 300 ns ns ns mV peak ( •) Peak to peak voltage symmetrical about VDD-VEE 2 (*) Both ends of channel. 5/17 HCC/HCF4051B/52B/53B Typical Channel ON Resistance vs. Input Signal Voltage (all types). Typical Channel ON Resistance vs. Input Signal Voltage (all types). Typical Channel ON Resistance vs. Input Signal Voltage (all types). Typical Channel ON Resistance vs. Input Signal Voltage (all types). Typical Dynamic Power Dissipation/Package vs. Switching Frequency and Test Circuit (4051B). 6/17 HCC/HCF4051B/52B/53B Typical ON Characteristics for 1 of 8 Channels (4051B). Typical Dynamic Power Dissipation/Package vs. Switching Frequency and Test Circuit (4052B). Typical Dynamic Power Dissipation/Package vs. Switching Frequency and Test Circuit (4053B). 7/17 HCC/HCF4051B/52B/53B WAVEFORMS Channel Being Turned ON (RL = 10KΩ). Channel Being Turned OFF (RL = 300KΩ). TYPICAL BIAS VOLTAGES Fig. (a) Fig. (b) Fig. (c) Fig. (d) The ADDRESS (digital-control inputs) and INHIBIT logic levels are : ”0”=VSS and ”1”=V DD . The analog signal (trough the TG) may swing from VEE to VDD . 8/17 HCC/HCF4051B/52B/53B TYPICAL APPLICATIONS TYPICAL TIME-DIVISION APPLICATION OF THE 4052B SPECIAL CONSIDERATIONS Control of analog signals up to 20V peak-to-peak can be achieved by digital signal amplitudes of 4.5 to 20V (if VDD – VSS = 3V, a VDD – VEE of up to 13V can be controlled ; for VDD – VEE level differences above 13V, a VDD – VSS of at least 4.5V is required). For example, if VDD = + 5V, VSS = 0, and VEE = –13.5V, analog signals from – 13.5V to + 4.5V can be controlled by digital inputs of 0 to 4.5V. In certain applications, the external load-resistor current may include both VDD and signal-line components. To avoid drawing VDD current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0,8 volt (valvulated from RON values shown in ELECTRICAL CHARACTERISTICS CHART). No VDD current will flow through RL if the switch current flows into lead 3 on the HCC/HCF4051 ; leads 3 and 13 on the HCC/HCF4052 ; leads 4, 14, and 15 on the HCC/HCF4053. 9/17 HCC/HCF4051B/52B/53B TEST CIRCUITS Off Channel Leakage Current-any Channel OFF. 4051 4052 4053 Off Channel Leakage Current-all Channel OFF. 4051 4052 4053 Propagation Delay-adress Input to Signal Output. 4051 10/17 4052 4053 HCC/HCF4051B/52B/53B TEST CIRCUITS (continued) Propagation Delay-Inhibit Input to Signal Output. 4051 4052 4053 Input Voltage. 4051 4052 Quiescent Device Current. 4051 4053 4053 Channel ON Resistance Meaurement Circuit. 4052 11/17 HCC/HCF4051B/52B/53B TEST CIRCUITS (continued) Input Current. 4051 - 4053 Feedthrough (All Types). 4052 Crosstalk Betwen any two Channels (All Types). 12/17 Crosstalk Betweenn Duals or Triplets (4052-4053). HCC/HCF4051B/52B/53B Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 13/17 HCC/HCF4051B/52B/53B Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 14/17 HCC/HCF4051B/52B/53B SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 15/17 HCC/HCF4051B/52B/53B PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 16/17 HCC/HCF4051B/52B/53B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 17/17