Emerson Network Power IMP Intelligent mp sery Datasheet

Embedded Power for
Business-Critical Continuity
Rev.08.04.11_77
iMP Series
1 of 9
®
Intelligent MP
Series
Font: inion
M
Bold
or MP
f
Minion italic size
fororifeach
;
is the same
Created on Mac
Color:"i" 100% ,Blue
0%
5 Magenta
0% Yellow
, %0 Black
"MP" - 100% Black
Up to 1500 Watts
Total Power: Up to 1500 Watts
Input Voltage: 85 - 264 Vac
120-300 Vdc
# of Outputs: Up to 21
Special Features
• Full Medical EN60601 approval
• Intelligent I2C control
• Voltage adjustment on all outputs
(Manual or I2C)
• Configurable input and output
(case and module) OK signals and
indicators
• Configurable inhibit/enable
• Configurable output
UP/DOWN sequencing
• Configurable current limit
(foldback or constant current)
• High power density (8.8 W/cu-in)
• Intelligent fan
(speed control/fault status)
• Downloadable GUI from website
• Customer provided air option
• uP controlled PFC input with active
inrush protection
• I2C monitor of voltage, current, and
temp
• Programmable voltage, current limit,
inhibit/enable through I2C
• Optional extended hold-up module
(SEMI F47 compliance)
• Increased power density to 50% over
standard MP
• External switching frequency sync
input
• Optional conformal coating
• Industrial temp range (-40 ºC to 70 ºC)
• No preload required
• Industrial shock/vibration (> 50G’s)
Safety
•
•
•
•
UL
CSA
VDE
BABT
• CB
• CE
UL60950/UL2601**
CSA22.2 No. 234 Level 5
EN60950/EN60601-1**
Compliance to
EN60950/EN60601 BS7002
Certificate and report
Mark to LVD
Electrical Specifications
Input
Input ra­nge:
85 - 264 Vac 120 - 350 Vdc
(limited to 300 Vdc in medical applications)
Frequency:
47 - 440 Hz
Inrush current:
40 A peak max. (soft start)
Efficiency:
Up to 85% @ full case load
Power Factor:
0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
Turn-on time:
AC on 2.0 sec typ., inhibit/enable 150 ms typical
Programmable delay; 50 ms internal turn-on delay (Dual Output only)
EMI filter:
CISPR 22/EN55022 Level “B”**
Leakage current:
300 µA max. @ 240 Vac; 47 - 63 Hz
Radiated EMI:
CISPR 22/EN55022 Level “B”**
Holdover storage:
20 ms minimum (independent of input Vac) additional 34ms holdover
storage with optional HUP module
(SEMI F47 compatible). For iMP4 15 ms (low-line), 10 ms (high-line)
AC OK:
> 5 ms early warning min. before outputs lose regulation
Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)
Harmonic distortion:
Meets EN61000-3-2
Isolation:
Meets EN60950 and EN60601
Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; configurable
Input fuse (internal):
iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)
Warranty:
2 years
Embedded Power for
Business-Critical Continuity
Output
Adjustment range:*
± 10% minimum all outputs (manual)
(full module adjustment range using I2C)
Factory set point accuracy:
± 1%
I2C output program
accuracy:
± 5%
Margining:
± 4 - 6% nominal analog
(single output module only)
Overall regulation:
Rev.08.04.11_77
iMP Series
2 of 9
Output Continued
Reverse voltage protection: 100% of rated output current
Thermal protection:*
(OTP and OTW)
Configurable through I2C
All outputs disabled when internal temp
exceeds safe operating range. > 5 ms warning
(AC OK signal) before shutdown
0.4% or 20 mV max. (1500W modules 1% max.)
(36 W modules 4% maximum)
Remote sense:
p to 0.5 V total drop (not available on triple
U
output module)
Ripple:
RMS: 0.1% or 10mV, whichever is greater
Pk-Pk: 1.0% or 50mV, whichever is greater
Bandwidth limited to 20 MHz
Single wire parallel:
Current
share to within 2% of total rated
current
DC OK:*
± 5% of nominal. Configurable through I2C
Dynamic response:
< 2% or 100 mV, with 25% load step
Minimum load:
Not required
Recovery time:
To within 1% in < 300 µsec
Housekeeping standby:
Overcurrent
protection:**
Configurable through I2C (calibration required).
Single output module and main output of the
dual output module 105 - 120% of rated output
current. Aux output of dual output module 105
- 140% of rated output current
5 Vdc @ 1.0 A max. present whenever AC input
is applied (Optional 2.0 A available)
Module inhibit:*
Configured and controlled through I2C
Switching frequency:
250k Hz accepts external sync signal
Output/Output isolation:
>1 Megohm, 500 V
Short-circuit protection:
Protected for continuous short-circuit
Recovery is automatic upon removal of short
Overvoltage protection:*
Configurable through I2C
Single output module:
2 - 5.5 V 122 - 134% ; 6 - 60 V 110 - 120%
Dual output module:
2 - 6 V 122 - 134% ; 8 - 28 V 110 - 120%
Triple output module:
110 - 120% of highest voltage rating
TTL clock input signal used to adjust switching
frequency. Frequency 500 kHz ± 20%; Duty
cycle 40 - 55%
* Can be controlled via I2C
** Controlled via I2C but requires load calibration
External sync:
Environmental Specifications
Operating temperature:
Storage temperature:
Electromagnetic susceptibility:
-40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. ( -20 °C start up)
-40 °C to 85 °C
Designed to meet EN61000-4; ­­­-2, -3, -4, -5, -6, -8, -11 Level 3
Humidity:
Vibration:
MTBF demonstrated
Operating; non-condensing 10% to 95% RH
IEC68-2-6 to the levels of IEC721-3-2
> 550,000 hours at full load, 220 Vac and 25 °C ambient conditions
Output Module Line-up
Module Code
1
2
3
5
4
—
Module Type
Single
Single
Single
Single
Dual
Triple
Max output power
210 W
360 W
750 W
1500 W
144 W
36 W
Max output current
35 A
60 A
150 A
140 A
10 A
8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 - 15*,
2 - 6; 2 - 6, 2 - 6; 24 - 28, 24 - 28;
24 - 28, 2 - 6
8-15, 8-15, 2-6; 8-15, 8-15, 8-15;
8-15, 8-15, 18-28; 8-15, 18-28, 2-6
Output voltages available*
2-60 V
2-60 V
2-60 V
6-60 V
2A
18
Standard voltage increments
25
25
25
18
Remote sense
Remote margin
V-Program - I2C Control
Active Current Share
Module Inhibit - I2C Control
Module Inhibit - Analog
Overvoltage/Overcurrent
protection
Minimum load required
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
1
2
3
4
Slots occupied in any iVS case
* Note: Contact Factory for extended range down to 6 V
16
1
1
Embedded Power for
Business-Critical Continuity
Output Module Voltage/Current
2A
2A
2A
2A
2A
2A
2A
2A
1A
1A
1A
1A
1A
1A
0.5 A
0.5 A
0.5 A
0.5 A
—
—
—
—
—
—
—
1.8 - 2.2
2.0 - 2.4
2.7 - 3.3
3.0 - 3.6
4.5 - 5.5
4.7 - 5.7
5.0 - 6.1
5.4 - 6.6
7.2 - 8.8
9.0 - 11.0
9.9 - 12.1
10.8 - 13.2
12.6 - 15.4
13.5 - 16.5
16.2 - 19.8
18.0 - 22.0
21.6 - 26.4
25.2 - 30.8
27.0 - 33.0
29.7 - 36.3
32.4 - 39.6
37.8 - 46.2
43.2 - 52.8
48.6 - 59.4
54.0 - 66.0
2. USB to I2C module order code 73-769-001
Parallel Codes
7
6
Slot 2
—
—
—
—
—
—
—
—
1A
1A
1A
1A
1A
1A
0.5 A
0.5 A
0.5 A
0.5 A
—
—
—
—
—
—
—
Slot 1
—
—
—
—
—
—
—
—
1A
1A
1A
1A
1A
1A
—
—
—
—
—
—
—
—
—
—
—
iMP4
iMP8
3
2
1
5 4
Slot 2
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A
10 A* 10 A*
10 A
4A
10 A
4A
10 A
4A
10 A
4A
9A
4A
8A
4A
—
—
—
—
4A
2A
3A
2A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Ordering Note:
1. The cases and modules of both MP and iMP
series can be interchanged to allow more
flexibility. If intelligent modules are used
with non-intelligent cases, a numeric code
“4” is placed at the end of the module code
(ex. 4LL0 becomes 4LL4).
Slot 1 Slot 1
-
Slot 2
-
Slot 4
-
Slot 3 Slot 3
4
Slot 3
Z
35 A
60 A
150 A
—
35 A
60 A
150 A
—
35 A
60 A
150 A
—
35 A
60 A
150 A
—
35 A
60 A
150 A
—
35 A
60 A
144 A
—
34 A
58 A
136 A
—
23 A
42 A 97.5 A 140 A
20 A
36 A 84.4 A 140 A
75 A
140 A
18 A
32 A
17 A
31 A
68 A 136.3 A
17 A
30 A 62.5 A 125 A
14 A
21 A 53.5 A 107 A
14 A
20 A
50 A
100 A
11 A
19 A 41.6 A 83.3 A
10.5 A 18 A 37.5 A 75 A
8.5 A 15 A
30 A 62.5 A
6.7 A 11 A 26.8 A 53.5 A
50 A
6.5 A 11 A
25 A
6.2 A 10.9 A 22.7 A 35.8 A
5.8 A 10 A 20.8 A 35.8 A
4.2 A 7.5 A
16 A 35.7 A
4.0 A 7.5 A 15.6 A 31.2 A
3.7 A 6.0 A 13.9 A 27.7 A
3.5 A 6.0 A 12.5 A 25 A
4
Slot 5
Non-std**
5+
Slot 4
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
3
Slot 4
2V
2.2 V
3V
3.3 V
5V
5.2 V
5.5 V
6.0 V
8.0 V
10 V
11 V
12 V
14 V
15 V
18 V
20 V
24 V
28 V
30 V
33 V
36 V
42 V
48 V
54 V
60 V
2
Triple Output
Slot 6
1
I2C
Adjustment
Ranges****
Dual Output***
Slot 5 Slot 5
Single Output Module Code
Slot 7
Voltage
Code
Slot 6
­Voltage
Rev.08.04.11_77
iMP Series
3 of 9
available slots
available slots
iMP1
available slots
0 = no parallel
1=1&2
2=2&3
3=3&4
4=4&5
5=3&4&5
6=5&6
7=4&5&6
8=6&7
Special Voltage - Consult Factory for specifications
9 = 3 & 4, 6 & 7
*Note: Contact Factory for extended range down to 6 V.
**Increments of current not shown can be achieved by paralleling modules
(add currents of each module selected).
***Total output power on dual module must not exceed 144 W.
**** For single output modules only.
+ Applicable for iMP1 only.
A = 1 & 2, 3 & 4, 5 & 6
C = 2 & 3, 4 & 5
E = 3 & 4, 5 & 6
F = 2 & 3, 4 & 5, 6 & 7
Ordering Information
Case Size
iMP1*
Case Size (mm)
4 = 2.5” x 5” x 10”; 750 W-1100 W, 5 Slots
(63.5 x 127 x 254)
8 = 2.5” x 7” x 10”; 1000 W-1200 W, 6 Slots
(63.5 x 177.8 x 254)
1 = 2.5” x 8” x 11”; 1200 W-1500 W, 7 Slots
(63.5 x 203.2 x 279.4)
*Note: Add “E” after iMP4 to denote IEC
input option. e.g. iMP4E
(Not available on iMP8 or iMP1)
Module/Voltage/Option Codes
First - Module Code
Second - Voltage Code
Third - Option Code
- 3L0 - 2E2 - 1Q1 - 4LL0 Module Codes
Module/voltage/option codes
Module codes:
(None) = 36 W triple O/P (1 slot)
1 = 210 W single O/P (1 slot)
2 = 360 W single O/P (2 slot)
3 = 750 W single O/P (3 slot)
4 = 144 W dual O/P (1 slot)
5 = 1500 W single O/P (4 slot)
6 - 9 = future
Voltage Codes:
See Output Module Voltage/Current
table above
Option Codes:
0 = Standard
1 = Module enable
2 = Constant current
3 = 1 & 2 combined
4 = Set for use in standard
(non-intelligent case)
5 = Shutdown mode for 1500W
6 = 1 & 5 combined
7 - 9 = future
Software Code
Case Option Codes
00
Case Option Codes
First digit
0 - 9 = parallel code
(See Parallel Codes table above)
Second digit
0 = No options
1 = Reverse air
3 = Global enable
4 = Fan idle with inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 +3 +4
9 = CAN BUS/RS485 73-544-002
C = Opt 3 + Opt 9
-
A
Software code
used for configuration change. “A” is
standard
Hardware Code
-
###
Factory assembled
for hardware of
firmware mods.
Embedded Power for
Business-Critical Continuity
Single
Rev.08.04.11_77
iMP Series
4 of 9
iMP4 (AC input on opposite side)
S
L
O
T
S
L
O
T
S
L
O
T
S
L
O
T
S
L
O
T
5
4
3
2
1
-A
Input
90-264 Vac
180-264 Vac
iMP4 = 2.5” x 5” x 10” 5 available slots
(63.5 x 127 x 254)
210 W
750 W max.
1100 W max.
iMP8 and iMP1
S
L
O
T
7
AC input
S
L
O
T
6
S
L
O
T
5
S
L
O
T
4
S
L
O
T
3
S
L
O
T
2
S
L
O
T
1
iMP1 only
Input
85-264 Vac
180-264 Vac
360 W
iMP8 = 2.5” x 7” x 10” 6 available slots
(63.5 x 177.8 x 254mm)
1000 W max.
1200 W max.
iMP1 = 2.5” x 8” x 11”­­7 available slots
(63.5 x 203.2 x 279.4mm)
1200 W max.
1500 W max.
1
N
2
~
Pin Connectors
AC Input
Figure
3 1. AC Input
750 W
1
N
2
~
Pin No.
1
2
3
3 Figure 1. AC Input
PFC Input Connector (control and signals)
Figure 1. AC Input
Figure 2. Connector J1
1
5
16
5
6
10
10
Figure 2. Connector J1
Mates
Figure 2. with
Connector J1
Molex
90142-0010 Housing
90119-2110 Pin
Connector Kit Part No.:
70-841-004
1500 W
Figure 3. Connector J2
Dual
Triple
1
5
6
10
Figure
3. Connector J2
Mates
with
Landwin 2050S1000 Housing
2053T011V Pin
or
JST PHDR-10VS Housing
JST SPHD-002T-P0.5 (28-24)
JST SPHD-001T-P0.5 (26-22)
144 W
36 W
Connector Kit Part No.:
70-841-023
3
Function
AC neutral
AC line (hot)
Chassis (earth) ground
7
Pin No.
1
2
3
4
5
6
7
8
9
10
Function
Input AC OK - “emitter”
Input AC OK - “collector”
Global DC OK - “emitter”
Global DC OK - “collector”
External Sync
Global inhibit/optional enable logic “0”
Global inhibit/optional enable logic “1”
Global inhibit/optional enable return
+5 VSB housekeeping
+5 VSB housekeeping return
I2C Bus Output Connector
Pin No.
1
2
3
4
5
6
7
8
9
10
Function
No connection
No connection
No connection
Serial clock signal (SCL)
Serial data signal (SDA)
Address bit 0 (A0)
Address bit 1 (A1)
Address bit 2 (A2)
Secondary return (GND)
5 Vcc external bus (5 VCC. Bus)
Embedded Power for
Business-Critical Continuity
Rev.08.04.11_77
iMP Series
5 of 9
iMP Modules
DC-DC Converter Output Modules
Control Signal Information, J1 Control Connector
Single 210 Watt
.44” (11.2)
Function
1
2
3
4
5
6
7
8
9
10
+ Remote Sense
single or dual o/p main
Remote Margin / V. Program single o/p
N
Margin High
single o/p
1
- Remote Sense / Margin Low single or dual o/p main
2
Spare
3
Module, Isolated
Inhibit
single or dual o/p
Module Inhibit return
single or dual o/p
Current Share (SWP)
single or dual o/p main
+ Remote Sense V2
dual o/p, single is spare
Figure 1. AC Input
- Remote Sense V2
dual o/p, single is spare
*Note: All iMP modules have a green DCOK LED.
(except for 36 W module)
2X
.48"
~
(12.1)
Pin No.
M4X8 SCREWS WITH CONICAL WASHER
1.38"
(35.1)
V-
.44"
(11.4)
V ADJ
PIN 1
DC OUTPUT CONNECTOR
Figure 4. Connector J1
1
5
6
10
V+
.32"
(8.1)
Mates
with
Figure
2. Connector J1
Molex 90142-0010 Housing
90119-2110 Pin
Single 750 Watt
Single 360 Watt
.63”
.33”
(16.0)
(8.5)
V+
.63"
(16.0)
59.3 ± 0.2
(3x) 31.6 ±0.8
.59"
(15.0)
V+
11.3 ±0.8
V ADJ
.61"(15.6)
(2X)
.32"
(8.1)
.46 (11.7)
V1 +
(4X)
V1 V2 +
V2 -
.30 (7.5)(3X)
M3X8 SCREWS WITH SPRING WASHER
(4X)
1.17 (29.7)
.42 (10.7)
.32
(8.1)
PI
N
D
CO C O
NN UTP
EC UT
TO
R
Dual 144 Watt
V2 ADJ
V1 ADJ
PIN 1
DC OUTPUT CONNECTOR
(2x) 16.0 ±0.2
PIN 1
(2x) 16.0 ±0.2
M4X8 SCREWS W/
CONICAL WASHER (6X)
VADJ
DC OUTPUT CONNECTOR
.32”
(8.1)
(2x) 15.0 ±0.8
For Factory-Use Only
.44"
(11.0)
1.38” (35.2)
(2X)
.44”
(11.4)
V-
8.1 ±0.8
1.24"(11.0)
(2X)
.48” (12.1)
(2X)
M 4 X 8 SCREWS WITH
CONICAL WASHER
PIN 1
Single 1500 Watt
1
V
AD
J
M
(4 4X8
X) S
C
VRE
W
S
V-
V+
Triple 36 Watt
V1 ADJ
V2 ADJ
V1+
V2+
V3+
V3 ADJ
V1 +
V1-
V1 -
V2-
V2 +
V2 -
V3-
V3 +
V3 -
Mates with
Molex 09-91-0600 Housing
26-60-5060 Pin
Embedded Power for
Business-Critical Continuity
iMP Series
iMP4 (750/1100 Watts Max)
Notes
5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5mm x 127mm x 254mm)
Weight: iMP4 Case: 3 lbs. • 360 W Single 1.0 lb.
• 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Rev.08.04.11_77
iMP Series
6 of 9
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). (Optional IEC input connector)
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000
(Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
xy
xy
171.45
38.10
#8-32 MOUNTING HOLES
(4X) MARKED AS Y
Rev.08.04.11_77
iMP Series
7 of 9
171.45
Reverse Air Flow
7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5mm x 177.8mm x 254mm)
Weight: iMP8 Case: 4.1 lbs. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.
• 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.
Normal Air Flow
iMP Series
iMP8 (1000/1200 Watts Max)
M4 MOUNTING HOLES (4X)
IDENTICAL BOTH SIDES
Embedded Power for
Business-Critical Continuity
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series)
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000
(Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
Embedded Power for
Business-Critical Continuity
iMP Series
iMP1 (1200/1500 Watts Max)
8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5mm x 203.2mm x 279.4mm)
Weight: iMP1 Case: 5.0 lb. • 210 W Single: 0.6 lb.
• 360 W Single: 1.0 lb. • 750 W Single: 1.6 lb.
• 144 W Dual: 0.6 lb.
Rev.08.04.11_77
iMP Series
8 of 9
Normal Air Flow
Reverse Air Flow
M4 MOUNTING HOLES (4X)
IDENTICAL BOTH SIDES
171.45
38.10
#8-32 MOUNTING HOLES
(4X) MARKED AS Y
171.45
xy
xy
177.8
x
19.05
Notes
y
xy
M4 MOUNTING HOLES (4X)
MARKED AS X
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
Embedded Power for
Business-Critical Continuity
Optional CANBUS or RS485 Interface
­Americas
Rev.08.04.11_77
iMP Series
9 of 9
5810 Van Allen Way
Carlsbad, CA 92008
USA
Telephone: +1 760 930 4600
The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified
Facsimile: +1 760 930 0698
The RS485/CAN-to-I2C uses 2 Input Protocols and 1 Output Protocol.
Modus (Command Index: 0x02).
The Output Protocol use is: I2C with SMBus support (Command Index: 0x80).
S lav e/S erv er D ev ice(s)
A d ap te r
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
Telephone: +852 2176 3333
Facsimile: +852 2176 3888
O u tp u t P ro toco ls
I 2 C w ith S M B us
S upport
For global contact, visit:
www.Emerson.com/EmbeddedPower
A dapter P rotoc ol
A d ap te r C om m a n d
A d ap te r C o n tro ls
techsupport.embeddedpower
@emerson.com
While every precaution has been taken to ensure
accuracy and completeness in this literature, Emerson
Network Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
Inp ut P rotocols
R S 485 us in g
M o dbus
C AN usin g
M o difie d M od bus
Emerson Network Power.
The global leader in enabling
business-critical continuity.
AC Power
Connectivity
DC Power
M aster/C lie nt D ev ice(s)
RS485/CAN - to - I2C
For Detailed Info, Download the Software Requirements Specification (SRS) from
www.PowerConversion.com/imp
Embedded Computing
Embedded Power
Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
Racks & Integrated Cabinets
Services
Surge Protection
EmersonNetworkPower.com
iMP CAN RS485
Emerson Network Power and the Emerson
Network Power logo are trademarks and
service marks of Emerson Electric Co.
©2011 Emerson Electric Co.