AOZ8170 8-Line EMI Filter with Integrated ESD Protection General Description Features The AOZ8170 is an 8-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8170 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. z 8 lines for EMI filtering and ESD protection: The AOZ8170 consists of eight identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100Ω and a capacitance value of 8pF are used to achieve -20dB minimum attenuation from 700MHz to 3.0GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±15kV (air discharge) and ±15kV (contact discharge). This exceeds IEC 61000-4-2, level 4 ESD immunity test. z – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±15kV (air discharge) and ±15kV (contact discharge) z Trench Vertical Structure [TVS]2 ™ based technology z z z z z used to achieve excellent ESD clamping & filter performance over the full operating display range Filter performance: -20db attenuation from 700MHz to 3.0GHz Low operating voltage: 5.0V Capacitance stability over wide range of voltages and temperatures DFN package: 4.0mm x 1.6mm, 0.55mm pitch Pb-Free device Green product Applications z EMI filtering and ESD protection for data lines z LCD displays, camera interface, I/O interface z Portable handheld devices, cell phones, The AOZ8170 comes in an RoHS compliant, 4.0mm x 1.6mm, 0.55mm pitch DFN package and is rated over a -40°C to +85°C ambient temperature range. PDA phones Typical Application D0 100Ω CH1 8pF 8pF 100Ω D1 D7 CH2 8pF LCD/Camera Module 8pF 100Ω CH8 8pF 8pF Figure 1. Rev. 1.0 October 2010 www.aosmd.com Page 1 of 7 AOZ8170 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8170DT -40°C to +85°C TDFN-16 Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration 1 15 2 Exposed Pad (GND) 16 14 13 12 11 11 1616 22 1515 33 1414 44 1313 55 1212 66 1111 77 1010 88 99 3 4 5 6 10 7 9 8 TDFN-16 (Bottom View) TopView View Top Pin Description Rev. 1.0 October 2010 Pin Number Pin Name Pin Function 1,16 CH 1 Channel 1 Connections 2, 15 CH 2 Channel 2 Connections 3, 14 CH 3 Channel 3 Connections 4, 13 CH 4 Channel 4 Connections 5, 12 CH 5 Channel 5 Connections 6, 11 CH 6 Channel 6 Connections 7, 10 CH 7 Channel 7 Connections 8, 9 CH 8 Channel 8 Connections Exposed Pad GND Common Ground Connection www.aosmd.com Page 2 of 7 AOZ8170 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) ±15kV (1) ±15kV ESD Rating per Human Body Model(2) ±30kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM VBR IR VCL RCH CCH fC Parameter Reverse Working Voltage Conditions Max. Units 5.0 V 8 V 0.1 µA ILOAD = 1A, positive ILOAD = 1A, negative clamp(5)(8) 9.0 -2.5 V ILOAD = 5A, positive clamp(5)(8) ILOAD = 5A, negative clamp(5)(8) 11.5 -3.5 ILOAD = 12A, positive clamp(5)(8) ILOAD = 12A, negative clamp(5)(8) 14.0 -5.0 1mA(4) IT = Reverse Leakage Current VRWM = 3.3V Total Series Resistance Typ. (3) Reverse Breakdown Voltage Signal Clamp Voltage Min. 6 7 clamp(5)(8) IR = 20mA Ground(6)(7)(8) 90 100 110 Ω 7 8 9 pF Channel Capacitance Input to Cut-off Frequency Measured with 50Ω source and 50Ω load termination 220 MHz Attenuation from 700MHz to 3.0GHz VR = 0V Measured with 50Ω source and 50Ω load termination -20 dB Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. 6. Total capacitance is equal to 2 x CCH. 7. Measured at 25°C, VR = 2.5V, f = 1.0MHz. 8. Guaranteed by design. Rev. 1.0 October 2010 www.aosmd.com Page 3 of 7 AOZ8170 Typical Performance Characteristics Insertion Loss Characteristics Crosstalk (I/O-I/O) vs. Frequency 0 0 -5 -20 -10 Insertion Loss (dB) S21 (db) -15 -20 -25 -30 -35 -40 -40 -60 -80 -100 -45 -50 -120 1 10 100 1000 10000 1 10 Frequency (MHz) Clamping Voltage vs. Peak Pulse Current (tperiod = 100ns, tr = 1ns) 1000 10000 Forward Voltage vs. Forward Current (tperiod = 100ns, tr = 1ns) 6 16 Clamping Voltage, Vcl (V) 100 Frequency (MHz) 5 14 4 12 3 10 2 8 1 0 6 0 2 4 6 8 10 0 12 2 4 6 8 10 12 Forward Current (A) Peak Pulse Current, Ipp (A) Typical Resistance vs. Temperature 110 Resistance (Ω) 105 100 95 90 -45 -25 -5 5 25 45 65 85 Temparature (°C) Rev. 1.0 October 2010 www.aosmd.com Page 4 of 7 AOZ8170 Package Dimensions, TDFN 4 x 1.6 D D1 b E1 E L e Pin 1 Marking TOP VIEW Pin #1 ID Chamfer 0.2 x 45° BOTTOM VIEW A c A1 SIDE VIEW Dimensions in millimeters RECOMMENDED LAND PATTERN 3.30 0.25 0.45 1.35 Symbols A A1 b c D E D1 E1 e L Min. 0.50 0.00 0.20 Nom. Max. 0.55 0.60 — 0.05 0.25 0.30 0.152 REF. 3.95 4.00 4.05 1.55 1.60 1.65 3.15 3.20 3.25 0.40 0.45 0.50 0.50 BSC 0.25 0.30 0.35 Dimensions in inches Symbols A A1 b c D E D1 E1 e L Min. Nom. Max. 0.020 0.022 0.024 0.000 — 0.002 0.008 0.010 0.012 0.006 REF. 0.156 0.157 0.159 0.061 0.063 0.065 0.124 0.126 0.128 0.016 0.018 0.020 0.020 BSC 0.010 0.012 0.014 0.675 0.25 0.50 0.35 UNIT: mm Note: 1. Controlling dimension is millimeter. Converted inch dimensions are not necessarily exact. Rev. 1.0 October 2010 www.aosmd.com Page 5 of 7 AOZ8170 Tape and Reel Dimensions, TDFN 4 x 1.6 Carrier Tape P2 P1 B D1 D0 E1 K0 R0.3 Max. E2 E B0 5° Max A0 P0 T B Feeding Direction Unit: mm Package DFN 4x1.6 A0 2.00 ±0.1 B0 4.40 ±0.1 K0 0.95 ±0.1 D0 ø1.50 +0.1/-0 D1 ø1.00 +0.1/-0 E 12.00 ±0.3 E1 1.75 ±0.10 Reel E2 5.50 ±0.1 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.10 T 0.30 ±0.05 W1 S R K M N H Unit: mm Tape Size Reel Size 12mm ø330 M ø330.00 ±0.30/-4.00 N 55.00 ±0.40 W1 12.4 +2.0/-0 H 13.00 ±0.20 S 2.20 ±0.20 K 10.60 ±0.20 R — Leader / Trailer & Orientation Trailer Tape 300mm min. Rev. 1.0 October 2010 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. Page 6 of 7 AOZ8170 Part Marking H1F Assembly Lot Code Week and Year Code Part Number Code Alpha & Omega Semiconductor reserves the right to make changes to this data sheet at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.0 October 2010 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 7 of 7