M54HC163 RAD-HARD SYNCHRONOUS PRESETTABLE 4-BIT COUNTER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: fMAX = 62 MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 163 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9204-073 DESCRIPTION The M54HC163 is an high speed CMOS SYNCHRONOUS 4 BIT BINARY PRESETTABLE COUNTER fabricated with silicon gate C2MOS technology. DILC-16 FPC-16 ORDER CODES PACKAGE FM EM DILC FPC M54HC163D M54HC163K M54HC163D1 M54HC163K1 The CLOCK input is active on the rising edge. Both LOAD and CLEAR inputs are active LOW. Presetting is synchronous on the rising edge of the clock, the function is synchronous to the CLOCK. Two enable inputs (TE and PE) and CARRY output are provided to enable easy cascading of counters, which facilities easy implementation of N-bit counters without using external gates. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION March 2004 1/12 M54HC163 IEC LOGIC SYMBOLS INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° SYMBOL NAME AND FUNCTION 1 CLEAR 2 CLOCK 3, 4, 5, 6 7 10 9 14, 13, 12, 11 15 8 A, B, C, D PE TE LOAD Asynchronous Master Reset Clock Input (LOW to HIGH, Edge-triggered) Data Inputs Count Enable Input Count Enable Carry Input Parallel Enable Input QA to QD Flip Flop Outputs 16 CARRY GND VCC Terminal Count Output Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OUTPUTS FUNCTION CLEAR LOAD PE TE L X X H L H QA QB QC QD X L L L L RESET TO "0" X X A B C D PRESET DATA H X L NO CHANGE NO COUNT H H L X NO CHANGE NO COUNT H H H H COUNT UP COUNT H X X X NO CHANGE NO COUNT X : Don’t Care A, B, C, D: Logic level of data inputs Carry : CARRY = TE·QA·QB·QC·QD 2/12 CLOCK M54HC163 LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays TIMING CHART 3/12 M54HC163 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage Top Operating Temperature Input Rise and Fall Time tr, tf 4/12 Value Unit 2 to 6 V 0 to VCC V 0 to VCC V -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns M54HC163 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 Unit V 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10 6.0 IO=-5.2 mA 5.68 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=4.0 mA 0.17 0.26 0.33 0.40 6.0 IO=5.2 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VCC or GND 4 40 80 µA 5.8 5.63 V 5.60 V 5/12 M54HC163 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (CLOCK - Q) tPLH tPHL Propagation Delay Time (CLOCK - CARRY) tPLH tPHL Propagation Delay Time (TE - CARRY) tPHL tPHL fMAX Propagation Delay Time (CLEAR-Q) Propagation Delay Time (CLEAR - CARRY) Maximum Clock Frequency tW(H) tW(L) Minimum Pulse Width (CLOCK) ts Minimum Set-up Time (LOAD, PE, TE) ts ts th tREM 6/12 Minimum Set-up Time (A, B, C, D) Minimum Set-up Time (CLEAR) Minimum Hold Time (A, B - CLOCK) Minimum Removal Time VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C Min. 6.2 31 37 Typ. Max. 25 7 6 48 16 14 57 19 16 39 13 11 72 24 20 39 13 11 18 53 62 18 6 6 40 10 8 20 5 3 20 5 3 75 15 13 125 25 21 150 30 26 100 20 17 200 40 34 100 20 17 18 4 3 -40 to 85°C -55 to 125°C Min. Min. Max. 95 19 16 155 31 26 190 38 32 125 25 21 250 50 43 125 25 21 5 25 30 75 15 13 100 20 17 75 15 13 75 15 13 0 0 0 50 10 9 Max. 110 22 19 190 38 32 225 45 38 150 30 26 300 60 51 150 30 26 4.2 21 25 95 19 16 125 25 21 95 19 16 95 19 16 0 0 0 65 13 11 Unit ns ns ns ns ns ns MHz 110 22 19 150 30 26 110 22 19 110 22 19 0 0 0 75 15 13 ns ns ns ns ns ns M54HC163 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 50 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAY TIMES, MINIMUM PULSE WIDTH (COUNT MODE) (f=1MHz; 50% duty cycle) 7/12 M54HC163 WAVEFORM 2: SETUP AND HOLD TIMES (CLEAR MODE) (f=1MHz; 50% duty cycle) WAVEFORM 3: SETUP AND HOLD TIMES (PRESET MODE) (f=1MHz; 50% duty cycle) 8/12 M54HC163 WAVEFORM 4: SETUP AND HOLD TIMES (COUNTENABLE MODE) (f=1MHz; 50% duty cycle) WAVEFORM 5: PROPAGATION DELAY TIMES (CASCADE MODE) (f=1MHz; 50% duty cycle) 9/12 M54HC163 DILC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.71 0.083 0.107 a1 3.00 3.70 0.118 0.146 a2 0.63 1.14 0.025 B 1.82 2.39 0.072 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 20.06 20.32 20.58 0.790 0.800 0.810 e 7.36 7.62 7.87 0.290 0.300 0.310 e1 0.88 2.54 0.035 0.045 0.094 0.100 e2 17.65 17.78 17.90 0.695 0.700 0.705 e3 7.62 7.87 8.12 0.300 0.310 0.320 F 7.29 7.49 7.70 0.287 0.295 0.303 I 3.83 0.151 K 10.90 12.1 0.429 0.476 L 1.14 1.5 0.045 0.059 0056437F 10/12 M54HC163 FPC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.94 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.102 0.127 0.152 0.004 0.005 0.006 E 8.76 8.89 9.01 0.345 0.350 0.355 F 0.077 1.27 G 0.38 H 6.0 L 18.75 M 0.33 0.050 0.43 0.48 0.015 0.017 0.019 0.237 0.38 N 22.0 0.738 0.43 0.013 0.867 0.015 4.31 0.017 0.170 G F D H 9 16 A N L 8 1 H E B M C 0016030E 11/12 M54HC163 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 12/12