MB05S THRU MB10S SINGLE PHASE 0.8AMP SURFACE MOUNT GLASS PASSIVATED BRIDGE RECTIFIER Features · Glass Passivated Die Construction · Low leakage · Ideal for printed circuit board MBS · Surge overload rating-30A peak - · Designed for Surface Mount Application · Plastic Material-UL Flammability 94V-0 ~ ) · Case:Reliable low cost construction utilizing molded plastic technique · ~ STD-202,Method208 Polarity:As Marked on Case · Mounting Position:Any · Marking:Type Number 0.090(2.3) MAX. Terminals:Plated Leads Solderable per MIL- · 0.106(2.7) 0.028(0.7) 0.020(0.5) 0.010 0.25 Mechanical Data + 0.195(4.95) 0.177(4.5) 0.161(4.1) 0.142(3.6) 0.043(1.1) 0.023(0.6) 0.067(1.7) 0.051(1.3) dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ ambient temperature unless otherwise specified. Single Phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER SYMBOL MB05S MB1S MB2S MB4S MB6S MB8S MB10S UNITS VRRM Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRWM RMS Reverse Voltage VRMS Average Rectified Output Current (Note 1)@TC=100℃ (Note 2)@TC=100℃ IF(AV) 0.5 0.8 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30 A I2t Rating for Fusing (t < 8.3ms) I 2t 3.735 A2s VFM 0.95 1.0 V 50 100 200 400 600 800 1000 V 35 70 140 280 420 560 700 V VDC Forward Voltage per element @IF=0.5A @IF=0.8A Peak Reverse Current At Rated DC Blocking Voltage @TA=25℃ @TA=125℃ IR 5.0 200 uA Typical Junction Capacitance per leg (Note 3) CJ 13 pF RθJA 60 RθJL 16 TJ,TSTG -55to+150 Typical Thermal Resistance per leg Operating and Storage Temperature Range ℃/W ℃ 2 Note:1. Mounted on glass epoxy PC board with 1.3mm solder pad. 2. Mounted on aluminum substrate PC board with 1.3mm 2 solder pad. 3. Measured at 1.0 MHz and applied reverse voltage of 4.0V D.C. version:02 1 of 3 www.dyelec.com Fig. 1 Output Current Derating Curve 1.0 IF, INSTANTANEOUS FORWARD CURRENT (A) I(AV), AVERAGE FORWARD RECTIFIED CURRENT (A) MB05S THRU MB10S Al. Substrate PC Board 0.6 0.4 Glass Epoxy PC Board 0.2 0 0 40 80 120 Fig. 2 Typical Forward Characteristics (per leg) 10 1.0 0.1 TA= 25°C Pulse Width = 300µs 0.01 0.2 160 0.6 0.8 1.0 1.2 1.4 Fig. 3 Maximum Peak Forward Surge Current (per leg) 35 Fig. 4 Typical Junction Capacitance 100 TJ = 25°C f = 1.0MHz Cj, JUNCTION CAPACITANCE (pF) 30 20 10 TA = 25°C Single Half Sine-Wave Pulse Width = 8.3ms (JEDEC Method) 0 1.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) TC , CASE TEMPERATURE (°C) IFSM, PEAK FORWARD SURGE CURRENT (A) 0.4 10 1 1.0 10 1 NUMBER OF CYCLES AT 60 Hz 10 100 VR, REVERSE VOLTAGE (V) INVSTANTANEOUS REVERSE CURRENT (µA) FIG.5 TYPICAL REVERSE CHRACTERISTICS FIG.6 MOUNTING PAD LAYOUT 1000 O TJ= 125 C 100 10 1.0 O TJ= 25 C 0.1 20 40 60 80 100 120 PERCENT OF RATED PEAK INVERSE VOLTGE (V) version:02 2 of 3 www.dyelec.com MB05S THRU MB10S Important Notice and Disclaimer •Reproducing and modifying information of the document is prohibited without permission from DIYI. • DIYI reserves the right to make changes to this document and its products and specifications at any time without notice. Customers should obtain and confirm the latest product information and specifications before final design, purchase or use. •DIYI disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. •DIYI does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Applications shown on the here in document are examples of standard use and • operation. Customers are responsible in comprehending the suitable use in particular applications. DIYI makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. •The products shown here in are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify DIYI for any damages resulting from such improper use or sale. •Since DIYI uses lot number as the tracking base, please provide the lot number for tracking when complaining. version:02 3 of 3 www.dyelec.com