POWER DCH2 Series 2 Watts Data Sheet Total Power: 2 Watts Input Voltage: 90 - 264 Vac # of Outputs: Single SPECIAL FEATURES Switching wallmount power supply Available in multiple AC plug configurations CE Mark EMC & LVD Universal AC input Overload and short circuit protection Constant voltage, constant current output Built in EMI filter (CISPR 22 Class B) No load power consumption < 300 mW SAFETY UL CSA TUV NEMKO CB CE 60950/6500 60950 60950 60950 Certificate and report EMC & LVD Electrical Specifications Input Input range 90 - 264 Vac (wide range) Frequency 47 - 63 Hz EMI/RFI FCC Part 15, Subpart B Class B & EN55022 (CISPR 22) Class B & EMC89/336/EEC Safety ground leakage current 10 μA @ 50/60 Hz, 230 Vac input Output Voltage (Vo) 6.5 V (6.5 - 10 V) Maximum power (Po) 2W Hold-up time 12 ms typical at full load @ 115 Vac Overvoltage protection 25% above nominal output maximum; Latching type Overload protection Output short circuit protection auto recover Overload protected > 2 A Output cable/connector barrel polarity DC cable with 2.8 mm x 5.5 mm barrel plug right angle DC plug center +V; DC plug outer -V Environmental Specifications Operating temperature 0° to 45 °C ambient Storage temperature -30 °C to +85 °C Electromagnetic susceptibility Designed to meet EN55082-1 Humidity Operating; non-condensing 20% to 90% RH Vibration Per IEC 60068-2-6 DCH2 Series Data Sheet Ordering Information Model Number Maximum Power Output Voltage Minimum Load Maximum Load Peak Load Ripple P/P (PARD)1 DCH2-050US-0001 2W 6.5 V 0 0.3 A 0.5 A 800 mV DCH2-050EU-0001 2W 6.5 V 0 0.3 A 0.5 A 800 mV DCH2-050UK-0001 2W 6.5 V 0 0.3 A 0.5 A 800 mV DCH2-050AU-0001 2W 6.5 V 0 0.3 A 0.5 A 800 mV 1. Peak-to-peak with 1MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 2. Output should not be grounded for EMI purpose. Mechanical Drawings DCH2-050US DCH2-050EU 1.50” (38) 72.83” (1850) 1.50” (38) 0.70” (17.9) 72.83” (1850) 1.75” (44.4) 0.374” (9.5) 1.75” (44.4) 0.70” (17.9) 1.02” (26) 1.50” (38 ± 0.2) 0.374” (9.5) 0.55” (14) 1.42” (36.1) OD (-) ID (+) OD (-) ID (+) PIN OUT DETAIL PIN OUT DETAIL Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ± .02”. 3. Warranty: 2 years 4. Weight: 0.181 lb./0.082kg. DCH2 Series Data Sheet Mechanical Drawings DCH2-050UK 1.69” (43.6) 72.83” (1850) 0.80” (20.4) 2.00” (51) PIN OUT DETAI L OD (-) ID (+) DCH2-050AU 1.50” (38) 72.83” (1850) .374” (9.5) 1.75” (44.4) .705” (17.9) OD(-) PIN OUT DETAIL 1.02” (26) ID(+) WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DCH2 Series-DS 16Jul2015