Kingbright AM27SURC03 Subminiature solid state lamp Datasheet

SUBMINIATURE SOLID STATE LAMP
AM27SURC03
HYPER RED
Description
Features
The Hyper Red source color devices are
SUBMINIATURE PACKAGE.
made with DH InGaAlP on GaAs substrate
GULL WING.
LONG LIFE - SOLID STATE RELIABILITY.
Light Emitting Diode.
LOW PACKAGE PROFILE.
PACKAGE :1000PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1296
REV NO: V.3
DATE: APR/07/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: H.Q.YUAN
ERP:1202000388
Selection Guide
Part No.
Dice
AM27SURC03
Iv (mcd)
@ 20mA
Lens Type
HYPER RED (InGaAlP)
Viewing
Angle
Min.
Typ.
2 θ 1/2
280
1000
20°
WATER CLEAR
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Hyper Red
λD
Dominant Wavelength
∆λ1/2
Typ.
Max.
Units
Test Conditions
640
nm
IF=20mA
Hyper Red
628
nm
IF=20mA
Spectral Line Half-width
Hyper Red
27
nm
IF=20mA
C
Capacitance
Hyper Red
45
pF
VF=0V;f=1MHz
VF
Forward Voltage
Hyper Red
1.9
2.5
V
IF=20mA
IR
Reverse Current
Hyper Red
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Units
Power dissipation
170
mW
DC Forward Current
30
mA
Peak Forward Current [1]
185
mA
5
V
Reverse Voltage
Operating / Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1296
REV NO: V.3
DATE: APR/07/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: H.Q.YUAN
ERP:1202000388
Hyper Red
AM27SURC03
SPEC NO: DSAD1296
REV NO: V.3
DATE: APR/07/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: H.Q.YUAN
ERP:1202000388
AM27SURC03
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO: DSAD1296
REV NO: V.3
APPROVED: J. Lu
CHECKED: Allen Liu
DATE: APR/07/2005
PAGE: 4 OF 4
DRAWN: H.Q.YUAN
ERP:1202000388
D
i
g
i
t
a
l
l
y
s
i
g
n
e
d
b
y
N
I
N
G
T
I
N
G
c
n
=
N
I
N
G
T
I
N
G
,
o
=
N
I
N
G
T
I
N
G
,
c
=
C
N
D
a
t
e
:
2
0
0
5
.
0
4
.
0
7
1
5
:
3
4
:
4
5
+
0
8
'0
0
'R
e
a
s
o
n
:
<
n
o
n
e
>
Similar pages