Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers AD8613/AD8617/AD8619 Battery-powered instrumentation Multipole filters Current shunt sense Sensors ADC predrivers DAC drivers/level shifters Low power ASIC input or output amplifiers GENERAL DESCRIPTION The AD8613/AD8617/AD8619 are single, dual, and quad micropower, rail-to-rail input and output amplifiers that feature low supply current, as well as low input voltage and current noise. The parts are fully specified to operate from 1.8 V to 5 V single supply, or ±0.9 V and ±2.5 V dual supply. The combination of low noise, very low input bias currents, and low power consumption make the AD8613/AD8617/AD8619 especially useful in portable and loop-powered instrumentation. The ability to swing rail-to-rail at both the input and output enables designers to buffer CMOS ADCs, DACs, ASICs, and other wide output swing devices in low power, single-supply systems. 1 AD8613 V– 2 +IN 3 TOP VIEW (Not to Scale) V+ 4 –IN OUT A 1 –IN A 2 AD8617 +IN A 3 TOP VIEW (Not to Scale) V– 4 8 V+ 7 OUT B 6 –IN B 5 +IN B 05622-001 Figure 1. 5-Lead SC70 and 5-Lead TSOT-23 Figure 2. 8-Lead MSOP and 8-Lead SOIC_N OUT A 1 8 V+ AD8617 –IN A 2 7 OUT B TOP VIEW (Not to Scale) +IN A 3 6 –IN B 5 +IN B V– 4 NOTES 1. PIN 4 AND THE EXPOSED PAD MUST BE CONNECTED TO V–. Figure 3. 8-Lead LFCSP_VD OUT A 1 14 OUT D –IN A 2 13 +IN A 3 AD8619 V+ 4 TOP VIEW (Not to Scale) +IN B 5 10 +IN C –IN B 6 9 –IN C OUT B 7 8 OUT C –IN D 12 +IN D 11 V– Figure 4. 14-Lead TSSOP OUT A 1 14 OUT D –IN A 2 +IN A 3 V+ 4 +IN B 5 The AD8613 is available in a 5-lead SC70 package and a 5-lead TSOT-23 package. The AD8617 is available in 8-lead MSOP, 8-lead SOIC, and 8-lead LFCSP packages. The AD8619 is available in 14-lead TSSOP and 14-lead SOIC packages. The AD8617W is qualified for automotive applications and is available in an 8-lead MSOP package and an 8-lead SOIC package. 5 05622-037 OUT 05622-022 APPLICATIONS PIN CONFIGURATIONS 05622-035 Offset voltage: 2.2 mV maximum Low input bias current: 1 pA maximum Single-supply operation: 1.8 V to 5 V Low noise: 22 nV/√Hz Micropower: 50 μA/amplifier maximum over temperature No phase reversal Unity gain stable Qualified for automotive applications 13 AD8619 –IN D 12 +IN D TOP VIEW 11 V– (Not to Scale) 10 +IN C –IN B 6 9 –IN C OUT B 7 8 OUT C 05622-036 FEATURES Figure 5. 14-Lead SOIC_N Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2005–2010 Analog Devices, Inc. All rights reserved. AD8613/AD8617/AD8619 TABLE OF CONTENTS Features .............................................................................................. 1 Thermal Resistance .......................................................................5 Applications ....................................................................................... 1 ESD Caution...................................................................................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Pin Configurations ........................................................................... 1 Outline Dimensions ....................................................................... 12 Revision History ............................................................................... 2 Ordering Guide .......................................................................... 15 Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 5 REVISION HISTORY 3/10—Rev. D to Rev. E Changes to General Description .................................................... 1 Changes to Ordering Guide .......................................................... 15 3/10—Rev. C to Rev. D Changes to General Description .................................................... 1 Changes to Ordering Guide .......................................................... 15 10/09—Rev. B to Rev. C Added 8-Lead LFCSP Package .......................................... Universal Changes to Features Section, Figure 2 Caption, General Description Section, and Figure 3 .................................................. 1 Changed VS to VSY Throughout ...................................................... 3 Changes to Input Characteristics, Input Voltage Range Parameter; Dynamic Performance, Settling Time to 0.1% and Phase Margin Parameters; and Noise Performance, Peak-toPeak Noise Parameter, Table 1 ........................................................ 3 Changes to Input Characteristics, Input Voltage Range Parameter; Dynamic Performance, Settling Time to 0.1% and Phase Margin Parameters; and Noise Performance, Peak-toPeak Noise Parameter, Table 2 ........................................................ 4 Changes to Table 3 and Table 4 ....................................................... 5 Changes to Figure 12 to Figure 15 .................................................. 7 Changes to Figure 18 Caption......................................................... 8 Changes to Figure 30 and Figure 31 ............................................. 10 Updated Outline Dimensions ....................................................... 12 Added Figure 44; Renumbered Sequentially .............................. 14 Changes to Ordering Guide .......................................................... 15 1/06—Rev. A to Rev. B Added AD8613 ................................................................... Universal Changes to Features ..........................................................................1 Changes to Table 1.............................................................................3 Changes to Table 2.............................................................................4 Updated Outline Dimensions ....................................................... 12 Changes to Ordering Guide .......................................................... 13 10/05—Rev. 0 to Rev. A Added AD8619 ................................................................... Universal Change to Specifications Section ....................................................3 Updated Outline Dimensions ....................................................... 12 Changes to Ordering Guide .......................................................... 13 9/05—Revision 0: Initial Version Rev. E | Page 2 of 16 AD8613/AD8617/AD8619 SPECIFICATIONS Electrical characteristics at VSY = 5 V, VCM = VSY/2, TA = 25°C, unless otherwise noted. Table 1. Parameter INPUT CHARACTERISTICS Offset Voltage Symbol Conditions VOS Offset Voltage Drift AD8613 Input Bias Current ∆VOS/∆T −0.3 V < VCM < +5.3 V −40°C < TA < +125°C, −0.3 V < VCM < +5.2 V −40°C < TA < +125°C Min Typ Max Unit 0.4 2.2 2.2 4.5 7.0 1 110 780 0.5 50 250 5 mV mV μV/°C μV/°C pA pA pA pA pA pA V dB dB V/mV pF pF 1 2.5 0.2 IB −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current IOS 0.1 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio IVR CMRR Large Signal Voltage Gain Input Capacitance AVO CDIFF CCM OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Settling Time to 0.1% Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Current Noise Density VOH VOL ISC ZOUT PSRR ISY SR tS GBP ØM en p-p en in 0 0 V < VCM < 5 V −40°C < TA < +125°C RL = 10 kΩ, 0.5 V < VO < 4.5 V IL = 1 mA −40°C to +125°C IL = 10 mA −40°C to +125°C IL = 1 mA −40°C to +125°C IL = 10 mA −40°C to +125°C 95 68 235 4.95 4.9 4.98 4.7 4.50 20 190 67 64 94 38 50 RL = 10 kΩ G = ±1, VIN = 2 V step, CL = 20 pF, RL = 1 kΩ RL = 100 kΩ RL = 10 kΩ RL = 10 kΩ, RL = 100 kΩ, CL = 20 pF 0.1 23 400 350 70 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 2.3 25 22 0.05 Rev. E | Page 3 of 16 30 50 275 335 ±80 15 f = 10 kHz, AV = 1 1.8 V < VSY < 5 V −40°C < TA < +125°C VO = VSY/2 −40°C <TA < +125°C 500 1.9 2.5 V V V V mV mV mV mV mA Ω dB dB μA μA V/μs μs kHz kHz Degrees 3.5 μV nV/√Hz nV/√Hz pA/√Hz AD8613/AD8617/AD8619 Electrical characteristics at VSY = 1.8 V, VCM = VSY/2, TA = 25°C, unless otherwise noted. Table 2. Parameter INPUT CHARACTERISTICS Offset Voltage Symbol Conditions VOS Offset Voltage Drift AD8613 Input Bias Current ∆VOS/∆T −0.3 V < VCM < +1.9 V −0.3 V < VCM < +1.8 V; −40°C < TA < +125°C −40°C < TA < +125°C Min Typ Max Unit 0.4 2.2 2.2 8.5 9.0 1 110 780 0.5 50 250 1.8 mV mV μV/°C μV/°C pA pA pA pA pA pA V dB dB V/mV pF pF 1 3.7 0.2 IB −40°C < TA < +85°C −40°C < TA < +125°C Input Offset Current IOS 0.1 −40°C < TA < +85°C −40°C < TA < +125°C Input Voltage Range Common-Mode Rejection Ratio IVR CMRR Large Signal Voltage Gain Input Capacitance AVO CDIFF CCM OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short-Circuit Current Closed-Loop Output Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Settling Time to 0.1% Gain Bandwidth Product Phase Margin NOISE PERFORMANCE Peak-to-Peak Noise Voltage Noise Density Current Noise Density 0 V < VCM < 1.8 V −40°C < TA < +125°C RL = 10 kΩ, 0.5 V < VO < 1.3 V 0 58 55 85 VOH IL = 1 mA −40°C to +125°C 1.65 1.6 VOL IL = 1 mA −40°C to +125°C ISC ZOUT PSRR ISY SR tS GBP ØM en p-p en in 1000 2.1 3.8 1.73 44 67 60 80 94 38 50 RL = 10 kΩ G = ±1, VIN = 1 V step, CL = 20 pF, RL = 1 kΩ RL = 100 kΩ RL = 10 kΩ RL = 10 kΩ, RL = 100 kΩ, CL = 20 pF 0.1 6.5 400 350 70 0.1 Hz to 10 Hz f = 1 kHz f = 10 kHz f = 1 kHz 2.3 25 22 0.05 Rev. E | Page 4 of 16 V V ±7 15 f = 10 kHz, AV = 1 1.8 V < VS < 5 V VO = VSY/2 −40°C <TA < +125°C 86 mV mV mA Ω dB μA μA V/μs μs kHz kHz Degrees 3.5 μV nV/√Hz nV/√Hz pA/√Hz AD8613/AD8617/AD8619 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. THERMAL RESISTANCE Table 3. θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Parameter Supply Voltage Input Voltage Input Current Differential Input Voltage Output Short-Circuit Duration to GND Storage Temperature Range Lead Temperature (Soldering, 60 sec) Operating Temperature Range Junction Temperature Range Rating 6V VSS − 0.3 V to VDD + 0.3 V ±10 mA ±6 V Indefinite −65°C to +150°C 300°C −40°C to +125°C −65°C to +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 4. Thermal Characteristics Package Type 5-Lead TSOT-23 (UJ-5) 5-Lead SC70 (KS-5) 8-Lead MSOP (RM-8) 8-Lead SOIC_N (R-8) 8-Lead LFCSP_VD (CP-8-9) 14-Lead SOIC_N (R-14) 14-Lead TSSOP (RU-14) ESD CAUTION Rev. E | Page 5 of 16 θJA 207 376 210 158 81 120 180 θJC 61 126 45 43 20 36 35 Unit °C/W °C/W °C/W °C/W °C/W °C/W °C/W AD8613/AD8617/AD8619 TYPICAL PERFORMANCE CHARACTERISTICS VSY = 5 V or ±2.5 V, unless otherwise noted. 1800 400 VSY = 5V AND 1.8V 350 1400 INPUT BIAS CURRENT (pA) 1200 1000 800 600 400 200 150 100 0 25 1900 1600 1300 1000 700 400 100 –200 –500 –800 –1100 –1400 –1700 –2000 0 250 50 05622-003 200 300 05622-006 NUMBER OF AMPLIFIERS VSY = 5.5V –0.5V < V < +5.5V 1600 T = 25°CCM A 50 75 100 150 125 TEMPERATURE (°C) INPUT OFFSET VOLTAGE (µV) Figure 9. Input Bias Current vs. Temperature Figure 6. Input Offset Voltage Distribution 50 40 –40°C < TA < 125°C VCM = 2.5V 35 TA = 25°C SUPPLY CURRENT (µA) NUMBER OF AMPLIFIERS 40 30 25 20 15 10 30 20 05622-004 0 0 1 2 3 4 5 6 7 8 9 05622-007 10 5 0 1 0 10 Figure 7. Input Offset Voltage Drift Distribution 50 SUPPLY CURRENT/AMPLIFIER (μA) INPUT OFFSET VOLTAGE (µV) 1500 1000 500 0 –500 –1000 05622-005 –1500 0.5 1.0 1.5 2.0 2.5 3.0 5 Figure 10. Supply Current vs. Supply Voltage VSY = 5V TA = 25°C 0 3 3.5 4.0 4.5 5.0 VSY = ±2.5V, ±1.35V, ±0.9V 40 30 20 10 0 –40 5.5 05622-008 2000 –2000 –0.5 2 SUPPLY VOLTAGE (V) TCVOS (µV/°C) –10 20 50 80 TEMPERATURE (°C) INPUT COMMON MODE VOLTAGE (V) Figure 8. Input Offset Voltage vs. Input Common-Mode Voltage Figure 11. Supply Current vs. Temperature Rev. E | Page 6 of 16 110 AD8613/AD8617/AD8619 135 60 VSY = 5V TA = 25ºC 50 OPEN-LOOP GAIN (dB) SOURCE 10 1 SINK 30 0.01 0.001 0.01 45 20 ΦM 10 0 0 VOL 0.1 90 40 0.1 VSY = ±2.5V AND ±0.9V RL = 100kΩ CL = 20pF –10 –20 1k 10 1 10k LOAD CURRENT (mA) 120 VSY = 5V AND 2.7V TA = 25°C 100 30 VSY – VOH @ 1mA CMRR (dB) 80 20 VOL @ 1mA 60 40 10 –25 –10 5 20 35 50 65 80 95 110 0 100 125 05622-013 20 05622-010 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) Figure 15. Open-Loop Gain and Phase vs. Frequency VSY = 5V 0 –40 1k Figure 13. Output Voltage to Supply Rail vs. Temperature (IL = 1 mA) 350 10k 100k 1M FREQUENCY (Hz) TEMPERATURE (°C) Figure 16. CMRR vs. Frequency 120 VSY = 5V VSY = ±2.5V AND ±1.35V TA = 25°C 300 100 VSY – VOH @ 10mA 250 PSRR (dB) 80 200 VOL @ 10mA 150 60 40 100 0 –40 –25 –10 5 20 35 50 65 80 95 110 0 100 125 05622-014 20 50 05622-011 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) –45 1M 100k FREQUENCY (Hz) Figure 12. Output Voltage to Supply Rail vs. Load Current 40 PHASE (Degrees) VSY – VOH 1k 10k 100k FREQUENCY (Hz) TEMPERATURE (°C) Figure 14. Output Voltage to Supply Rail vs. Temperature (IL = 10 mA) Figure 17. PSRR vs. Frequency Rev. E | Page 7 of 16 1M 05622-012 100 05622-009 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) 1k AD8613/AD8617/AD8619 1k VSY = 5V AV = 1 RL = 10kΩ CL = 200pF VOLTAGE (1V/DIV) 100 AV = 10 AV = 1 10 VSY = 5V AND 1.8V 0 100 1k 10k 100k 05622-018 1 05622-015 OUTPUT IMPEDANCE (Ω) AV = 100 TIME (20µs/DIV) 1M FREQUENCY (Hz) Figure 18. Output Impedance vs. Frequency Figure 21. Large Signal Transient Response 50 0 VOUT (V) SMALL SIGNAL OVERSHOOT (%) VSY = 5V 45 TA = 25°C 40 35 VSY = ±2.5V AV = –50 –2.5 30 –OS 25 20 VIN (mV) 100 15 +OS 0 05622-016 5 0 10 100 05622-019 10 TIME (20µs/DIV) 1000 LOAD CAPACITANCE (pF) Figure 19. Small Signal Overshoot vs. Load Capacitance Figure 22. Positive Overload Recovery VSY = 5V, 2.7V, 1.8V AV = 1 RL = 10kΩ CL = 200pF VSY = ±2.5V AV = –50 VOLTAGE (50mV/DIV) VOUT (V) 2.5 0 VIN (mV) 0 TIME (4µs/DIV) 05622-020 05622-017 –100 TIME (20µs/DIV) Figure 20. Small Signal Transient Response Figure 23. Negative Overload Recovery Rev. E | Page 8 of 16 AD8613/AD8617/AD8619 1000 VIN VOLTAGE (1V/DIV) VOUT 05622-021 VSY = ±2.5V AV = 1 RL = 10kΩ VIN = 6V p-p 100 10 1/F CORNER @ 100Hz 05622-023 INPUT VOLTAGE NOISE (nV/ Hz) VSY = 5V TA = 25ºC 1 TIME (20ms/DIV) 1 10 100 1000 10000 FREQUENCY (Hz) Figure 24. No Phase Reversal Figure 26. Voltage Noise Density 140 VSY = 5V AND 2.7V VSY = 5V 05622-022 CHANNEL SEPARATION (dB) VOLTAGE NOISE (1µV/DIV) 120 100 80 60 40 0 100 TIME (1s/DIV) 05622-024 20 1k 10k 100k FREQUENCY (Hz) Figure 25. 0.1 Hz to 10 Hz Input Voltage Noise Figure 27. Channel Separation Rev. E | Page 9 of 16 1M AD8613/AD8617/AD8619 VSY = 1.8 V or ±0.9 V, unless otherwise noted. 80 NUMBER OF AMPLIFIERS 400 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) VSY = 1.8V 0V < VCM < 1.8V TA = 25°C 350 300 250 200 150 05622-025 100 50 60 VSY–VOH @ 1mA 40 VOH @ 1mA 20 0 –40 1900 1600 1300 1000 700 400 100 –200 –500 –800 –1100 –1400 –1700 –2000 0 VSY = 1.8V 05622-028 450 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) INPUT OFFSET VOLTAGE (µV) Figure 28. Input Offset Voltage Distribution Figure 31. Output Voltage to Supply Rail vs. Temperature (IL = 1 mA) 2000 VSY = 1.8V TA = 25°C 80 1000 500 CMRR (dB) 0 –500 60 40 –1000 20 –2000 –0.5 05622-026 –1500 –0.2 0.1 0.4 0.7 1.0 1.3 1.6 1.9 0 100 2.2 05622-029 INPUT OFFSET VOLTAGE (µV) 1500 100 VSY = 1.8V TA = 25°C 1k 10k Figure 29. Input Offset Voltage vs. Input Common-Mode Voltage 1M Figure 32. CMRR vs. Frequency 1000 120 VSY = 1.8V TA = 25°C VSY = 1.8V TA = 25°C 100 100 VSY–VOH 80 SOURCE PSRR (dB) 10 1 SINK 60 40 VOL 0.1 0.01 0.001 0.01 0.1 1 0 100 10 LOAD CURRENT (mA) 05622-030 20 05622-027 OUTPUT VOLTAGE TO SUPPLY RAIL (mV) 100k FREQUENCY (Hz) INPUT COMMON-MODE VOLTAGE (V) 1k 10k FREQUENCY (Hz) Figure 33. PSRR vs. Frequency Figure 30. Output Voltage to Supply Rail vs. Load Current Rev. E | Page 10 of 16 1M AD8613/AD8617/AD8619 SMALL SIGNAL OVERSHOOT (%) 40 VSY = 1.8V VSY = 1.8V TA = 25°C VOLTAGE (1µV/DIV) 30 –OS 20 05622-031 05622-033 +OS 10 0 10 100 TIME (1s/DIV) 1k LOAD CAPACITANCE (pF) Figure 34. Small Signal Overshoot vs. Load Capacitance Figure 36. 0.1 Hz to 10 Hz Input Voltage Noise 1k VSY = 1.8V AV = 1 RL = 10kΩ CL = 200pF 100 1/F CORNER @ 100Hz 10 05622-034 05622-032 VOLTAGE (500mV/DIV) INPUT VOLTAGE NOISE (nV/ Hz) VSY = 1.8V TA = 25°C 1 TIME (20µs/DIV) 1 10 100 1k FREQUENCY (Hz) Figure 37. Voltage Noise Density Figure 35. Large Signal Transient Response Rev. E | Page 11 of 16 10k AD8613/AD8617/AD8619 OUTLINE DIMENSIONS 3.20 3.00 2.80 5.15 4.90 4.65 8 4.00 (0.1574) 3.80 (0.1497) 4 1 PIN 1 IDENTIFIER 4 6.20 (0.2441) 5.80 (0.2284) 1.27 (0.0500) BSC 0.65 BSC 0.95 0.85 0.75 15° MAX 6° 0° COPLANARITY 0.10 SEATING PLANE 0.80 0.55 0.40 0.23 0.09 COMPLIANT TO JEDEC STANDARDS MO-187-AA 0.51 (0.0201) 0.31 (0.0122) 8.75 (0.3445) 8.55 (0.3366) 8 14 1 7 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 0.51 (0.0201) 0.31 (0.0122) 6.20 (0.2441) 5.80 (0.2283) 0.50 (0.0197) 0.25 (0.0098) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 40. 14-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-14) Dimensions shown in millimeters and (inches) Rev. E | Page 12 of 16 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) Figure 39. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) Figure 38. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 4.00 (0.1575) 3.80 (0.1496) 0.50 (0.0196) 0.25 (0.0099) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 100709-B 0.40 0.25 1.75 (0.0688) 1.35 (0.0532) 0.25 (0.0098) 0.10 (0.0040) 1.10 MAX 0.15 0.05 COPLANARITY 0.10 5 012407-A 1 5 060606-A 8 3.20 3.00 2.80 5.00 (0.1968) 4.80 (0.1890) AD8613/AD8617/AD8619 5.10 5.00 4.90 14 8 4.50 4.40 4.30 6.40 BSC 1 7 PIN 1 0.65 BSC 1.20 MAX 0.15 0.05 COPLANARITY 0.10 0.20 0.09 SEATING PLANE 0.30 0.19 0.75 0.60 0.45 8° 0° 061908-A 1.05 1.00 0.80 COMPLIANT TO JEDEC STANDARDS MO-153-AB-1 Figure 41. 14-Lead Thin Shrink Small Outline Package [TSSOP] (RU-14) Dimensions shown in millimeters 2.20 2.00 1.80 1.35 1.25 1.15 5 1 4 2 3 2.40 2.10 1.80 0.65 BSC 0.10 MAX COPLANARITY 0.10 1.10 0.80 0.30 0.15 SEATING PLANE 0.40 0.10 0.22 0.08 0.46 0.36 0.26 COMPLIANT TO JEDEC STANDARDS MO-203-AA Figure 42. 5-Lead Thin Shrink Small Outline Transistor Package [SC70] (KS-5) Dimensions shown in millimeters Rev. E | Page 13 of 16 072809-A 1.00 0.90 0.70 AD8613/AD8617/AD8619 2.90 BSC 5 4 2.80 BSC 1.60 BSC 1 2 3 0.95 BSC 1.90 BSC *0.90 MAX 0.70 MIN 0.10 MAX 0.50 0.30 0.20 0.08 8° 4° 0° SEATING PLANE 0.60 0.45 0.30 100708-A *1.00 MAX *COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS. Figure 43. 5-Lead Thin Small Outline Transistor Package [TSOT-23] (UJ-5) Dimensions shown in millimeters 0.60 MAX 5 2.95 2.75 SQ 2.55 PIN 1 INDICATOR 8 EXPOSED PAD 4 0.50 0.40 0.30 TOP VIEW 12° MAX 0.90 MAX 0.85 NOM SEATING PLANE 0.70 MAX 0.65 TYP 0.05 MAX 0.01 NOM 0.30 0.23 0.18 0.50 BSC 0.60 MAX 0.20 REF 1.60 1.50 1.40 1 BOTTOM VIEW 2.23 2.13 2.03 PIN 1 INDICATOR FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. Figure 44. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD] 3 mm × 3 mm Body, Very Thin, Dual Lead (CP-8-9) Dimensions shown in millimeters Rev. E | Page 14 of 16 051909-A 3.25 3.00 SQ 2.75 AD8613/AD8617/AD8619 ORDERING GUIDE Model 1 AD8613AKSZ-R2 AD8613AKSZ-REEL AD8613AKSZ-REEL7 AD8613AUJZ-R2 AD8613AUJZ-REEL AD8613AUJZ-REEL7 AD8617ACPZ-R2 AD8617ACPZ-R7 AD8617ACPZ-RL AD8617ARMZ AD8617ARMZ-REEL AD8617ARZ AD8617ARZ-REEL AD8617ARZ-REEL7 AD8617WARMZ-REEL 2 AD8617WARZ-R72 AD8617WARZ-RL2 AD8619ARUZ AD8619ARUZ-REEL AD8619ARZ AD8619ARZ-REEL AD8619ARZ-REEL7 1 2 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 5-Lead SC70 5-Lead SC70 5-Lead SC70 5-Lead TSOT-23 5-Lead TSOT-23 5-Lead TSOT-23 8-Lead LFCSP_VD 8-Lead LFCSP_VD 8-Lead LFCSP_VD 8-Lead MSOP 8-Lead MSOP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead MSOP 8-Lead SOIC_N 8-Lead SOIC_N 14-Lead TSSOP 14-Lead TSSOP 14-Lead SOIC_N 14-Lead SOIC_N 14-Lead SOIC_N Z = RoHS Compliant Part. Qualified for automotive applications. Rev. E | Page 15 of 16 Package Option KS-5 KS-5 KS-5 UJ-5 UJ-5 UJ-5 CP-8-9 CP-8-9 CP-8-9 RM-8 RM-8 R-8 R-8 R-8 RM-8 R-8 R-8 RU-14 RU-14 R-14 R-14 R-14 Branding A0Y A0Y A0Y A0Y A0Y A0Y A0T A0T A0T A0T A0T A23 AD8613/AD8617/AD8619 NOTES ©2005–2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05622-0-3/10(E) Rev. E | Page 16 of 16