Rohm BD6370GUL 5ch system lens drivers for digital still camera Datasheet

System Lens Driver for Digital Still Cameras / Single-lens Reflex Cameras
5ch System Lens Drivers
for Digital Still Cameras
BD6370GUL, BD6758MWV, BD6758KN
No.09014EAT01
●Description
The BD6370GUL motor driver provides 3 Constant-Voltage Drive / Full-ON Drive H-bridge channels, 1 Constant-Voltage
Drive / Linear Constant-Current Drive / Full-ON Drive H-bridge channel, and 1 Constant-Current Drive H-bridge channel,
while the BD6758MWV and the BD6758KN provides 4 Full-ON Drive H-bridge channels and 1 Linear Constant-Current
Drive H-bridge channel.
A Stepping motor can be used for auto focus and a DC motor for zoom and iris. ROHM offers both an advance type equipped
with a D/A converter in all channels and a standard type, allowing selection of the ideal unit depending on the application.
●Features
3
1) Subminiature 24PIN Wafer-level CSP (Chip Size Package): 2.6 x 2.6 x 0.55mm (BD6370GUL)
2) Resemblance 6ch drive function (BD6370GUL)
3) Drive type selection (BD6370GUL)
4) Low ON-Resistance Power CMOS output:
All blocks (Const.-V/Full-ON Drive, Const.-V/Const.-C/Full-ON Drive, and Const.-Current Drive) with 1.4Ω Typ. (BD6370GUL)
Full-ON Drive block with 1.2Ω Typ. and Linear Constant-Current Drive block with 1.0Ω Typ. (BD6758MWV / KN)
5) Serial interface 3-line bus control input (BD6370GUL)
6) Built-in Constant-Voltage control 6-bit D/A converter and Constant-Current control 6-bit D/A converter resolution (BD6370GUL)
7) Built-in ±5% high-precision Constant-Voltage Driver (BD6370GUL)
8) Built-in ±3% high-precision Linear Constant-Current Driver
9) Constant-Voltage Drive block and Constant-Current Drive block features phase compensation capacitor-free design
10) 1.2V±3% high-precision reference voltage output (BD6758MWV / KN)
11) Drive mode switching function (BD6758MWV / KN)
12) UVLO (Under Voltage Lockout Protection) function
13) Built-in TSD (Thermal Shut Down) circuit
14) Standby current consumption: 0μA Typ.
●Absolute Maximum Ratings
Parameter
Symbol
Power supply voltage
Motor power supply voltage
Control input voltage
Power dissipation
Operating temperature range
Junction temperature
Storage temperature range
H-bridge output current
VCC
VM
VIN
Pd
Topr
Tjmax
Tstg
Iout
BD6370GUL
-0.3 to +6.5
-0.3 to +6.5
-0.3 to VCC+0.3
830※1
-25 to +85
+150
-55 to +150
-500 to +500※4
Limit
BD6758MWV
0 to +7.0
0 to +7.0
0 to VCC
880※2
-25 to +85
+150
-55 to +150
-800 to +800※4
BD6758KN
0 to +7.0
0 to +7.0
0 to VCC
875※3
-25 to +85
+150
-55 to +150
-800 to +800※4
Unit
V
V
V
mW
°C
°C
°C
mA/ch
※1 Reduced by 6.64mW/°C over 25°C, when mounted on a glass epoxy board (50mm  58mm  1.75mm; 8layers).
※2 Reduced by 7.0mW/°C over 25°C, when mounted on a glass epoxy board (74.2mm  74.2mm  1.6mm).
※3 Reduced by 7.0mW/°C over 25°C, when mounted on a glass epoxy board (70mm  70mm  1.6mm).
※4 Must not exceed Pd, ASO, or Tjmax of 150°C.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
1/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●Operating Conditions (Ta=-25 to +85°C)
Parameter
Power supply voltage
Motor power supply voltage
Control input voltage
Control input frequency
Serial clock input frequency
H-bridge output current
Symbol
VCC
VM
VIN
FIN
FSCLK
Iout
BD6370GUL
2.7 to 5.5
2.7 to 5.5
0 to VCC
100※5
10※5
-400 to +400※6
Limit
BD6758MWV
2.5 to 5.5
2.5 to 5.5
0 to VCC
100※5
-500 to +500※6
Unit
BD6758KN
2.5 to 5.5
2.5 to 5.5
0 to VCC
100※5
-500 to +500※6
V
V
V
kHz
MHz
mA/ch
※5 ON duty=50%
※6 Must not exceed Pd or ASO.
●Electrical Characteristics and Diagrams
1) BD6370GUL Electrical DC Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V, VM=5.0V)
Limit
Parameter
Symbol
Unit
Conditions
Min.
Typ.
Max.
Overall
Circuit current (Standby mode)
ICCST
0
3.0
μA PS=0V
Circuit current (Active mode)
ICC
1.3
2.0
mA PS=3V with no control signal, and no load
Control input (IN=PS, INPUT1, 2, 34, 45, STROBE, SCLK, and SDATA)
High level input voltage
VINH
2.0
VCC
V
Low level input voltage
VINL
0
0.7
V
High level input current 1
IINH1
15
30
60
μA VINH1 (PS, INPUT1, 2, 34, 45) =3V
High level input current 2
IINH2
7.5
15
30
μA VINH2 (STROBE, SCLK, SDATA) =3V
Low level input current
IINL
-1
0
μA VINL=0V
UVLO
UVLO voltage
VUVLO
1.6
2.4
V
Constant-Voltage Drive / Full-ON Drive block (ch1 to ch3)
Output ON-Resistance
RON
1.40
1.75
Ω
Io=±400mA on high and low sides in total
Output high voltage 1
VVOH1
1.35
1.50
1.65
V
DACx=6’b01_0100, RL=20Ω
Output high voltage 2
VVOH2
2.85
3.00
3.15
V
DACx=6’b10_1000, RL=20Ω
Output high voltage 3
VVOH3
4.49
4.725
4.96
V
DACx=6’b11_1111, RL=20Ω
DAC resolution
DVRES
6
BITS 75mV/LSB
Differential non-linear tolerance
DVDNL
-1
1
LSB
Integral non-linear tolerance
DVINL
-2
2
LSB
Min. voltage of DAC setting
DVRNG
1.5
V
DACx=6’b01_0100
Constant-Voltage Drive / Constant-Current Drive / Full-ON Drive block (ch4)
Output ON-Resistance
RON
1.40
1.75
Ω
Io=±400mA on high and low sides in total
Constant-Voltage Drive block in ch4
Output high voltage 1
VVOH1
1.35
1.50
1.65
V
DACV4=6’b01_0100, RL=20Ω
Output high voltage 2
VVOH2
2.85
3.00
3.15
V
DACV4=6’b10_1000, RL=20Ω
Output high voltage 3
VVOH3
4.49
4.725
4.96
V
DACV4=6’b11_1111, RL=20Ω
DAC resolution
DVRES
6
BITS 75mV/LSB
Differential non-linear tolerance
DVDNL
-1
1
LSB
Integral non-linear tolerance
DVINL
-2
2
LSB
Min. voltage of DAC setting
DVRNG
1.5
V
DACV4=6’b01_0100
Constant-Current Drive block in ch4
RNF voltage 1
VIRNF1
40
50
60
mV DACI4=6’b00_1010, RRNF4=0.5Ω, RL=10Ω
RNF voltage 2
VIRNF2
94
99
104
mV DACI4=6’b01_0100, RRNF4=0.5Ω, RL=10Ω
RNF voltage 3
VIRNF3
178
198
218
mV DACI4=6’b10_1000, RRNF4=0.5Ω, RL=10Ω
DAC resolution
DIRES
6
BITS 5mV/LSB
Differential non-linear tolerance
DIDNL
-1
1
LSB
Integral non-linear tolerance
DIINL
-2
2
LSB
Min. voltage of DAC setting
DIRNG
50
mV DACI4=6’b00_1010
Constant-Current Drive block (ch5)
Output ON-Resistance
RON
1.4
1.75
Ω
Io=±400mA on high and low sides in total
RNF voltage 1
VIRNF1
38
48
58
mV DAC5=6’b00_1010, RRNF5=0.5Ω, RL=10Ω
RNF voltage 2
VIRNF2
91
96
101
mV DAC5=6’b01_0100, RRNF5=0.5Ω, RL=10Ω
RNF voltage 3
VIRNF3
172
192
212
mV DAC5=6’b10_1000, RRNF5=0.5Ω, RL=10Ω
DAC resolution
DIRES
6
BITS 5mV/LSB
Differential non-linear tolerance
DIDNL
-1
1
LSB
Integral non-linear tolerance
DIINL
-2
2
LSB
Min. voltage of DAC setting
DIRNG
50
mV DAC5=6’b00_1010
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
2/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
2) BD6370GUL Electrical DC Characteristic Diagrams
4.0
Op. range
3.0
(2.7V to 5.5V)
2.0
1.0
BD6370GUL
5.0
Output ON resistance : RON [Ω]
Top 85°C
Mid 25°C
Low -25°C
4.0
Op. range
(2.7V to 5.5V)
3.0
2.0
1.0
0.0
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
2.0
1.0
1.0 2.0
3.0 4.0
5.0 6.0
7.0
0.0
Supply voltage : VM [V]
1.0 2.0
3.0 4.0
5.0 6.0
Fig.2 Output ON-Resistance
Fig.3 Output ON-Resistance
(ch1 to ch3)
(ch4 to ch5)
85°C
0.5
0.0
-25°C
25°C
-0.5
Operating range
BD6370GUL
2.0
-1.0
1.0
25°C
-25°C
0.0
85°C
-1.0
Operating range
-2.0
8
16
24
32
40
48
56
64
0
Serial setting value : DAC code [BIT]
Fig.4 Differential Non-Linear
Tolerance
25°C
-25°C
0.0
85°C
-0.5
Operating range
BD6370GUL
2.0
1.0
25°C
-25°C
0.0
85°C
-1.0
Operating range
-25°C
85°C
25°C
-0.5
Operating range
0
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
Fig.10 Differential Non-Linear
Tolerance
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
10
-25°C
25°C
0
85°C
-10
Operating range
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
0
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
Fig.9 RNF Voltage Accuracy
(Const.-Current drive block, RRNFx=0.5Ω, RL=10Ω)
(Const.-Current drive block, RRNFx=0.5Ω, RL=10Ω)
BD6370GUL
2.0
1.0
25°C
-25°C
0.0
85°C
-1.0
Operating range
-2.0
-1.0
BD6370GUL
20
Fig.8 Integral Non-Linear Tolerance
Integ.non-linear tolerance: DIINL [LSB]
0.0
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
-20
0
BD6370GUL
0.5
-20
0
-2.0
1.0
Operating range
(Const.-Voltage drive block, RL=20Ω)
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
Fig.7 Differential Non-Linear
Tolerance
85°C
-10
Fig.6 Output High Voltage Accuracy
-1.0
0
-25°C
(Const.-Voltage drive block, RL=20Ω)
Integ.non-linear tolerance: DIINL [LSB]
0.5
25°C
0
Fig.5 Integral Non-Linear Tolerance
BD6370GUL
1.0
10
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
RNF voltage accuracy: VIRNF [%]
0
BD6370GUL
20
Output high voltage accuracy: VVOH [%]
BD6370GUL
7.0
Supply voltage : VM [V]
(Active mode)
Integ.non-linear tolerance: DVINL [LSB]
Diff. non-linear tolerance : DVDNL [LSB]
(2.7V to 5.5V)
3.0
Fig.1 Circuit Current
1.0
Diff. non-linear tolerance : DIDNL [LSB]
Top 85°C
Mid 25°C
Low -25°C
Op. range
4.0
0.0
0.0
Supply voltage : VCC [V]
Diff. non-linear tolerance : DIDNL [LSB]
BD6370GUL
5.0
BD6370GUL
20
RNF voltage accuracy: VIRNF [%]
Circuit current : ICC [mA]
Top 85°C
Mid 25°C
Low -25°C
Output ON resistance : RON [Ω]
BD6370GUL
5.0
10
25°C
-25°C
0
85°C
-10
Operating Range
-20
0
8
16
24
32
40
48
56
Serial setting value : DAC code [BIT]
Fig.11 Integral Non-Linear
Tolerance
3/32
64
0
8 16 24 32 40 48 56 64
Serial setting value : DAC code [BIT]
Fig.12 RNF Voltage Accuracy
(Const.-Current drive block, RRNFx=1.0Ω, RL=10Ω)
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
3) BD6370GUL Electrical AC Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V, VM=5.0V)
Constant-Voltage / Full-ON Type Drive blocks (ch1 to ch3)
7
Information※
Parameter
Symbol
Unit
Conditions
ch1
ch2
ch3
Full-ON Drive Mode
Turn on time
ton
1.11
1.04
1.10
μs
Turn off time
toff
0.06
0.06
0.06
μs
DACx=6’b11_1111, RL=20Ω
Rise time
tr
1.64
1.42
1.50
μs
Fall time
tf
0.01
0.01
0.01
μs
Constant-Voltage Drive Mode
Turn on time
ton
1.26
1.23
1.22
μs
Turn off time
toff
0.04
0.04
0.04
μs
DACx=6’b10_1000, RL=20Ω
Rise time
tr
1.31
1.35
1.30
μs
Fall time
tf
0.02
0.02
0.02
μs
Constant-Voltage / Constant-Current / Full-ON Type Drive block (ch4)
Information※7
Parameter
Symbol
Unit
Conditions
ch4
Full-ON Drive Mode
Turn on time
ton
0.76
μs
DACV4=6’b11_1111,
Turn off time
toff
0.05
μs
DACI4=6’b11_1111,
Rise time
tr
0.68
μs
RL=20Ω
Fall time
tf
0.02
μs
Constant-Voltage Drive Mode
Turn on time
ton
1.19
μs
DACV4=6’b10_1000,
Turn off time
toff
0.04
μs
DACI4=6’b11_1111,
Rise time
tr
1.31
μs
RL=20Ω
Fall time
tf
0.01
μs
Constant-Current Drive Mode
Turn on time
ton
0.83
μs
DACV4=6’b11_1111,
Turn off time
toff
0.05
μs
DACI4=6’b10_1100 (IO=400mA),
RRNFI4=0.5Ω, RL=10Ω,
Rise time
tr
0.89
μs
RMETALI4=4mΩ, RW=40mΩ
Fall time
tf
0.03
μs
Turn on time
ton
0.69
μs
DACV4=6’b11_1111,
Turn off time
toff
0.04
μs
DACI4=6’b10_1010 (IO=200mA),
Rise time
tr
0.29
μs
RRNFI4=1.0Ω, RL=10Ω,
RMETALI4=4mΩ, RW=40mΩ
Fall time
tf
0.03
μs
Constant-Current Type Drive block (ch5)
Information※7
Parameter
Symbol
Unit
Conditions
ch5
Constant-Current Drive Mode
Turn on time
ton
0.77
μs
DAC5=6’b10_1101 (IO=400mA),
Turn off time
toff
0.04
μs
RRNF5=0.5Ω, RL=10Ω,
Rise time
tr
0.47
μs
RMETAL5=22mΩ, RW=40mΩ
Fall time
tf
0.04
μs
Turn on time
ton
0.69
μs
DAC5=6’b10_1010 (IO=200mA),
Turn off time
toff
0.04
μs
RRNF5=1.0Ω, RL=10Ω,
Rise time
tr
0.24
μs
RMETAL5=22mΩ, RW=40mΩ
Fall time
tf
0.02
μs
※7 AC characteristics are reference values, then the performance of IC’s characteristics is not guaranteed.
100%
INPUTx
50%
50%
toff
toff
90%
Dead
Time
OUTxA-OUTxB current
0%
ton
ton
100%
90%
Dead
Time
50%
50%
10%
10%
-10%
-10%
-50%
0%
-50%
-90%
-90%
tf
tr
tf
-100%
tr
Fig.13 The Definition of I/O Switching
Waveforms
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
4/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
4) BD6370GUL Electrical AC Characteristic Diagrams
BD6370GUL
BD6370GUL
BD6370GUL
INPUT1,2,or34
voltage
[5V/div]
INPUT1,2,or34
voltage
[5V/div]
INPUT34or45
voltage
[5V/div]
OUTxA-xB
current
[100mA/div]
OUTxA-xB
current
[100mA/div]
OUT4A-4B
current
[100mA/div]
[500nsec/div]
[500nsec/div]
[500nsec/div]
Fig.14 I/O AC Responses (ton, tr)
Fig.15 I/O AC Responses (ton, tr)
Fig.16 I/O AC Responses (ton, tr)
ch1 to ch3 Full-ON Drive Mode
DACx=6’b11_1111, RL=20Ω
ch1 to ch3Constant-Voltage Drive Mode
DACx=6’b10_1000, RL=20Ω
ch4 Full-ON Drive Mode
DACV4=DACI4=6’b11_1111, RL=20Ω
BD6370GUL
BD6370GUL
BD6370GUL
INPUT1,2,or34
voltage
[5V/div]
INPUT1,2,or34
voltage
[5V/div]
INPUT34or45
voltage
[5V/div]
OUTxA-xB
current
[100mA/div]
OUTxA-xB
current
[100mA/div]
OUT4A-4B
current
[100mA/div]
[20nsec/div]
[20nsec/div]
[20nsec/div]
Fig.17 I/O AC Responses (toff, tf)
Fig.18 I/O AC Responses (toff, tf)
Fig.19 I/O AC Responses (toff, tf)
ch1 to ch3 Full-ON Drive Mode
DACx=6’b11_1111, RL=20Ω
ch1 to ch3Constant-Voltage Drive Mode
DACx=6’b10_1000, RL=20Ω
ch4 Full-ON Drive Mode
DACV4=DACI4=6’b11_1111, RL=20Ω
BD6370GUL
BD6370GUL
BD6370GUL
INPUT34or45
voltage
[5V/div]
INPUT34or45
voltage
[5V/div]
OUT4A-4B
current
[200mA/div]
OUT4A-4B
current
[100mA/div]
OUT5A-5B
current
[200mA/div]
[500nsec/div]
[500nsec/div]
[500nsec/div]
Fig.20 I/O AC Responses (ton, tr)
Fig.21 I/O AC Responses (ton, tr)
Fig.22 I/O AC Responses (ton, tr)
ch4 Constant-Voltage Drive Mode
DACV4=6’b10_1000, DACI4=6’b11_1111, RL=20Ω
ch4 Constant-Current Drive Mode
DACV4=6’b11_1111, DACI4=6’b10_1100, RRNFI4=0.5Ω, RL=10Ω
ch5 Constant-Current Drive Mode
DAC5=6’b10_1101, RRNF5=0.5Ω, RL=10Ω
BD6370GUL
BD6370GUL
BD6370GUL
INPUT34or45
voltage
[5V/div]
INPUT34or45
voltage
[5V/div]
INPUT45
voltage
[5V/div]
OUT4A-4B
current
[100mA/div]
OUT4A-4B
current
[200mA/div]
OUT5A-5B
current
[200mA/div]
[20nsec/div]
[20nsec/div]
[20nsec/div]
Fig.23 I/O AC Responses (toff, tf)
Fig.24 I/O AC Responses (toff, tf)
Fig.25 I/O AC Responses (toff, tf)
ch4 Constant-Voltage Drive Mode
DACV4=6’b10_1000, DACI4=6’b11_1111, RL=20Ω
ch4 Constant-Current Drive Mode
DACV4=6’b11_1111, DACI4=6’b10_1100, RRNFI4=0.5Ω, RL=10Ω
ch5 Constant-Current Drive Mode
DAC5=6’b10_1101, RRNF5=0.5Ω, RL=10Ω
AC characteristics are reference values, then the performance of IC’s characteristics is not guaranteed.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
5/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
BD6370GUL
BD6370GUL
INPUT34or45
voltage
[5V/div]
OUT4A-4B
current
[200mA/div]
OUT5A-5B
current
[200mA/div]
[500nsec/div]
[500nsec/div]
Fig.26 I/O AC Responses (ton, tr)
Fig.27 I/O AC Responses (ton, tr)
ch4 Constant-Current Drive Mode
DACV4=6’b11_1111, DACI4=6’b10_1010, RRNFI4=1.0Ω, RL=10Ω
ch5 Constant-Current Drive Mode
DAC5=6’b10_1010, RRNF5=1.0Ω, RL=10Ω
BD6370GUL
BD6370GUL
INPUT34or45
voltage
[5V/div]
INPUT45
voltage
[5V/div]
OUT4A-4B
current
[200mA/div]
OUT5A-5B
current
[200mA/div]
[20nsec/div]
[20nsec/div]
Fig.28 I/O AC Responses (toff, tf)
Fig.29 I/O AC Responses (toff, tf)
ch4 Constant-Current Drive Mode
DACV4=6’b11_1111, DACI4=6’b10_1010, RRNFI4=1.0Ω, RL=10Ω
ch5 Constant-Current Drive Mode
DAC5=6’b10_1010, RRNF5=1.0Ω, RL=10Ω
AC characteristics are reference values, then the performance of IC’s characteristics is not guaranteed.
5) BD6758MWV and BD6758KN Electrical Characteristics (Unless otherwise specified, Ta=25°C, VCC=3.0V, VM=5.0V)
Limit
Symbol
Unit
Parameter
Conditions
Min.
Typ.
Max.
Overall
Circuit current
ICCST
0
10
μA
PS=0V
during standby operation
Circuit current
ICC
1.4
2.5
mA
PS=VCC with no signal
Control input (IN=PS, IN1A to 5B, SEL1 to 2, BRK1 to 2, EN1, and IN5)
High level input voltage
VINH
2.0
V
Low level input voltage
VINL
0.7
V
High level input current
IINH
15
30
60
μA
VINH=3V
Low level input current
IINL
-1
0
μA
IVINL=0V
Pull-down resistor
RIN
50
100
200
kΩ
UVLO
UVLO voltage
VUVLO
1.6
2.4
V
Full-ON Drive block (ch1 to ch4)
Output ON-Resistance
RON
1.2
1.5
Ω
Io=±400mA on high and low sides in total
Linear Constant-Current Drive block (ch5)
Output ON-Resistance
RON
1.0
1.25
Ω
Io=±400mA on high and low sides in total
VREF output voltage
VREF
1.16
1.20
1.24
V
Iout=0~1mA
Output limit voltage
VOL
194
200
206
mV
RNF=0.5Ω, VLIM=0.2V
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
6/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
6) BD6758MWV and BD6758KN Electrical AC Characteristic Diagrams
4.0
Op. range
3.0
(2.5V to 5.5V)
2.0
1.0
BD6758MWV, BD6758KN
5.0
Output ON resistance : RON [Ω]
Circuit current : ICC [mA]
Top 85°C
Mid 25°C
Low -25°C
Top 85°C
Mid 25°C
Low -25°C
4.0
Op. range
3.0
(2.5V to 5.5V)
2.0
1.0
0.0
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Op. range
3.0
(2.5V to 5.5V)
2.0
1.0
1.0 2.0
3.0 4.0
5.0 6.0
7.0
0.0
Supply voltage : VM [V]
Supply voltage : VCC [V]
Fig.30 Circuit current
1.0 2.0
3.0 4.0
5.0 6.0
7.0
Supply voltage : VM [V]
Fig.31 Output ON-Resistance
Fig.32 Output ON-Resistance
(Full-ON Drive block)
(Linear Constant-Current Drive block)
BD6758MWV, BD6758KN
250
RNF voltage : VRNF [mV]
Top 85°C
Mid 25°C
Low -25°C
4.0
0.0
0.0
7.0
BD6758MWV, BD6758KN
5.0
Output ON resistance : RON [Ω]
BD6758MWV, BD6758KN
5.0
200
150
100
Top 85°C
Mid 25°C
Low -25°C
50
0
0
50
100
150
200
250
VLIM voltage : VLIM [mV]
Fig.33 Output limit voltage
(RNF=0.5Ω)
●Power Dissipation Reduction
BD6370GUL
880mW
830mW
600
400
432mW
200
85°C
0
0
25
50
75
100 125 150
Ambient temperature : Ta [°C]
Fig.34 Power Dissipation
Reduction
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
875mW
800
600
458mW
400
200
85°C
0
0
25
BD6758KN
1000
Power dissipation : Pd [mW]
800
BD6758MWV
1000
Power dissipation : Pd [mW]
Power dissipation : Pd [mW]
1000
50
75
100 125 150
Ambient temperature : Ta [°C]
Fig.35 Power Dissipation
Reduction
7/32
800
600
455mW
400
200
85°C
0
0
25
50
75
100 125 150
Ambient temperature : Ta [°C]
Fig.36 Power Dissipation
Reduction
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●Block Diagram, Pin Arrangement, and Pin Function
VCC
E3
PS B3
Power Save & Serial Reset
TSD & UVLO
BandGap
Level Shift
C.V./Full ON
Serial Interface
H bridge
INPUT1 D3
Logic12
INPUT2 C3
&
Pre Driver
Serial Interface
H bridge
C.V./Full ON
Serial Interface
6bit DAC12
Serial Interface
H bridge
&
C.V./Full ON
Pre Driver
C5 OUT2B
D5 OUT3A
E4 OUT3B
E5 PGND
STROBE B4
SCLK D4
A5 OUT1B
B5 OUT2A
VDAC12
Level Shift
Logic3
A4 OUT1A
Serial
Interface
SDATA C4
Serial Interface
6bit DAC3
VDAC3
Selector
Logic4
2
3
4
5
A
RNF4
OUT4A
VM
OUT1A
OUT1B
B
OUT4B
PS
STROBE
OUT2A
A3 VM
Level Shift
Serial Interface
1
H bridge
&
C.V./C.C./Full ON
Pre Driver
A2 OUT4A
B1 OUT4B
INDEX
POST
A1 RNF4
INPUT34 D2
INPUT45 C2
Serial Interface
Selector
6bit DACI4
VDACI4
Serial Interface
Serial Interface
6bit DACV4
Serial Interface
OUT5A
INPUT45
INPUT2
SDATA
OUT2B
D
OUT5B
INPUT34
INPUT1
SCLK
OUT3A
E
RNF5
GND
VCC
OUT3B
PGND
VDACV4
Level Shift
Logic5
C
H bridge
&
Const. Current
Pre Driver
C1 OUT5A
D1 OUT5B
E1 RNF5
Serial Interface
6bit DAC5
VDAC5
E2
GND
Fig.37 BD6370GUL Block Diagram
No.
A1
A2
A3
A4
A5
B1
B2
B3
B4
B5
C1
C2
C3
C4
C5
Pin
Name
RNF4
OUT4A
VM
OUT1A
OUT1B
OUT4B
INDEX POST
PS
STROBE
OUT2A
OUT5A
INPUT45
INPUT2
SDATA
OUT2B
Fig.38 BD6370GUL Pin Arrangement (Top View)
VCSP50L2 Package
BD6370GUL Pin Function Table
Pin
Function
No.
Name
Resistance connection pin for output current detection ch4
D1
OUT5B
H-bridge output pin ch4 A
D2 INPUT34
Motor power supply pin
D3
INPUT1
H-bridge output pin ch1 A
D4
SCLK
H-bridge output pin ch1 B
D5
OUT3A
H-bridge output pin ch4 B
E1
RNF5
E2
GND
Power-saving pin
E3
VCC
Serial enable input pin
E4
OUT3B
H-bridge output pin ch2 A
E5
PGND
H-bridge output pin ch5 A
Control input pin ch4 or ch5
Control input pin ch2
Serial data input pin
H-bridge output pin ch2 B
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
8/32
Function
H-bridge output pin ch5 B
Control input pin ch3 or ch4
Control input pin ch1
Serial clock input pin
H-bridge output pin ch3 A
Resistance connection pin for output current detection ch5
Ground pin
Power supply pin
H-bridge output pin ch3 B
Motor ground pin ch1 to ch3
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
VCC
4
PS 35
Power Save
TSD & UVLO
BandGap
31 VM1
IN1B
1
IN2A
2
IN2B
3
29 OUT1A
H bridge
IN1A 36
Level Shift
Logic12
Full ON
30 OUT1B
&
Pre Driver
33 OUT2A
H bridge
Full ON
34 OUT2B
SEL1 28
32 PGND1
14 VM2
15 PGND2
Const. Current
Pre Driver
25 OUT5B
23 RNF
VREF
20
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
VLIM
9
GND
Fig.40 BD6758MWV / KN Pin Arrangement (Top View)
MWV=UQFN036V5050 Package
KN=VQFN36 Package
BD6758KN Pin Function Table
Pin
Function
No.
Name
Control input pin ch1 B
19
VLIM
Control input pin ch2 A
20
VREF
Control input pin ch2 B
21
OUT5A
Power supply pin
22
SENSE
Ground pin
23
RNF
Control input pin ch3 A
24
VM3
Control input pin ch3 B
25
OUT5B
Control input pin ch4 A
26
IN5
Control input pin ch4 B
27
EN1
Control input pin ch3 BRAKE
28
SEL1
Control input pin ch4 BRAKE
29
OUT1A
H-bridge output pin ch3 A
30
OUT1B
H-bridge output pin ch3 B
31
VM1
Motor power supply pin ch3 and ch4
32
PGND1
Motor ground pin ch3 and ch4
33
OUT2A
H-bridge output pin ch4 A
34
OUT2B
H-bridge output pin ch4 B
35
PS
Drive mode selection pin ch3 and ch4
36
IN1A
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
VLIM
VREF
OUT5A
RNF
VM3
BRK1
5
Fig.39 BD6758KN Block Diagram
No.
BRK2
IN1A
22 SENSE
VREF
Pin
Name
IN1B
IN2A
IN2B
VCC
GND
IN3A
IN3B
IN4A
IN4B
BRK1
BRK2
OUT3A
OUT3B
VM2
PGND2
OUT4A
OUT4B
SEL2
36
OUT3A
PS
IN4B
IN5 26
OUT2B
21 OUT5A
H bridge
&
OUT4A
BD6758MWV PGND2
PGND1
VM2
OUT2A
BD6758KN OUT3B
IN4A
Level Shift
OUT1B
18
VM1
24 VM3
Logic5
OUT4B
IN3B
BRK2 11
SEL2
OUT1A
IN3A
SEL2 18
BRK1 10
EN1 27
SEL1
17 OUT4B
VCC
Full ON
SENSE
16 OUT4A
H bridge
GND
Pre Driver
IN5
9
13 OUT3B
&
OUT5B
IN4B
Logic34
27
IN2B
8
Full ON
EN1
7
IN4A
Level Shift
IN2A
IN3B
12 OUT3A
H bridge
6
IN1B
IN3A
9/32
Function
Output current setting pin ch5
Reference voltage output pin
H-bridge output pin ch5 A
Output current detection ch5
Resistance connection pin for output current detection ch5
Motor power supply pin ch5
H-bridge output pin ch5 B
Control input pin ch5 INPUT
Control input pin ch5 ENABLE
Drive mode selection pin ch1 and ch2
H-bridge output pin ch1 A
H-bridge output pin ch1 B
Motor power supply pin ch1 and ch2
Motor ground pin ch1 and ch2
H-bridge output pin ch2 A
H-bridge output pin ch2 B
Power saving pin
Control input pin ch1 A
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●BD6370GUL Function Explanation
Bypass filter Capacitor for
power supply input. (p.29/32)
1～100uF
Power-saving (p.11/32)
H : Active
L : Standby
Motor control input
(p.11/32)
VCC
E3
PS B3
Power Save & Serial Reset
TSD & UVLO
BandGap
Serial Interface
H bridge
INPUT1 D3
Level Shift
Logic12
INPUT2 C3
C.V./Full ON
&
Pre Driver
Serial Interface
H bridge
C.V./Full ON
Serial Interface
6bit DAC12
A4
A5
B5
C5
OUT1A
M
OUT1B
Resemblance drive
mode (p.11/32)
OUT2A
OUT2B
VDAC12
M
Level Shift
Serial control input
(p.12/32)
Logic3
Serial Interface
C.V./Full ON
Pre Driver
D5
E4
E5
STROBE B4
SCLK D4
H bridge
&
Serial
Interface
Serial Interface
SDATA C4
6bit DAC3
OUT3A
OUT3B
Bypass filter Capacitor for
power supply input. (p.29/32)
PGND
VDAC3
1～100uF
Selector
A3
VM
Level Shift
Logic4
Motor control input
(p.11/32)
Serial Interface
INPUT34 D2
INPUT45 C2
H bridge
&
C.V./C.C./Full ON
Pre Driver
Serial Interface
Selector
6bit DACI4
VDACI4
RMETALI4
=4mΩ (Typ.)
A2
B1
A1
OUT4A
OUT4B
RNF4
RRNFI4
Serial Interface
Serial Interface
6bit DACV4
Level Shift
Logic5
Serial Interface
H bridge
&
Const. Current
Pre Driver
Serial Interface
6bit DAC5
The output current is converted to a voltage
with the RNF4 external resistor. (p.11/32)
Iout[A] = VDACI4[V]÷(RMETALI4[Ω]＋RRNFI4[Ω])
In the case of Const.-Voltage or Full-ON
mode, no need to connect the RRNFI4.
VDACV4
VDAC5
RMETAL5
=22mΩ (Typ.)
C1
D1
E1
OUT5A
OUT5B
RNF5
RRNF5
E2
GND
The output current is converted to a voltage
with the RNF5 external resistor. (p.11/32)
Iout[A] = VDAC5[V]÷(RMETAL5[Ω]＋RRNF5[Ω])
Fig.41 BD6370GUL Application Circuit Diagram
1) Power saving and Serial Reset (BD6370GUL; PS)
(1) Function Explanation
2) Control Input (BD6370GUL; INPUTx)
(1) Function Explanation
3) H-bridge (BD6370GUL; VM, OUTxA, OUTxB, and RNFx)
(1) Function Explanation
(2) The D/A Converter Settings of Constant-Voltage, Constant-Current, and Full-ON Mode
4) Serial Input (BD6370GUL; STROBE, SCLK, and SDATA)
(1) Function Explanation
(2) Serial Register Bit Map
5) Serial Register Data Bit Function (BD6370GUL)
(1) Address Bit [000] Function Explanation
(2) Address Bit [001] Function Explanation
(3) Address Bit [010] Function Explanation
(4) Address Bit [011] Function Explanation
(5) Address Bit [100] Function Explanation
6) I/O Truth Table (BD6370GUL)
7) The More Precise Constant-Current Settings (BD6370GUL)
8) Application Control Sequence (BD6370GUL)
(1) Stepping Motor drive controlled by 2 phases mode
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
10/32
p.11/32
p.11/32
p.11/32
p.11/32
p.12/32
p.12/32
p.13/32 to p.14/32
p.15/32
p.16/32 to p.17/32
p.18/32 to p.19/32
p.20/32
p.21/32 to p.23/32
p.24/32 to p.23/32
p.25/32 to p.26/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
1) Power-saving and Serial Reset (BD6370GUL; PS)
(1) Function Explanation
When Low-level voltage is applied to PS pin, the IC will be turned off internally and the circuit current will be 0μA (Typ.).
During operating mode, PS pin should be High-level. (See the Electrical Characteristics; p.2/32)
Be cancelled power saving mode after turned on power supply VCC and VM, because of PS terminal combines power
saving with serial reset function. If the case of power saving terminal always shorted power supply terminal, reset
function may not be well, and it may cause the IC to malfunction. (See the Sequence of Serial Control Input; p.12/32)
2) Motor Control Input (BD6370GUL; INPUTx)
(1) Function Explanation
These pins are used to program and control the motor drive modes. So INPUTx switches CW or CCW, CW or Brake,
and CCW or Brake, using serial function. (See the Electrical Characteristics; p.2/32 and I/O Truth Table; p.21/32 to
p.23/32)
INPUT34 and INPUT45 pins drive ch3 or ch4, and ch4 or ch5, respectively. The driven channel is selected using
serial function. (See the Driven Outputs for INPUT Terminal Table; p.14/32)
3) H-bridge (BD6370GUL; VM, OUTxA, OUTxB, and RNFx)
(1) Function Explanation
The H-bridge output transistors of BD6370GUL are Power CMOS Drivers. The total H-bridge ON-Resistance on the
high and low sides varies with the VM voltage. The system must be designed so that the maximum H-bridge current
for each channel is 500mA or below.
The 3 H-bridges of ch1 to ch3 can be driven as the resemblance 4-channels. For this reason, it is possible to drive the
2 Stepping Motors by ch1 to ch3 as long as the 2 motors don’t move simultaneously. The selection of resemblance
drive mode for ch1 to ch3 is set using serial function. (See the Driven Outputs for INPUT Terminal Table; p.14/32)
The 2 control input terminals of INPUT34 and INPUT45 drive the 3 H-bridges of ch3 to ch5. Use caution because it is
impossible to drive all 3 H-bridges simultaneously.
(2) The D/A Converter Settings of Constant-Voltage, Constant-Current, and Full-ON Mode
The ch1 to ch3 enable Constant-Voltage or Full-ON Driving, and the ch4 enables Constant-Voltage, Constant-Current,
or Full-ON Driving, while the ch5 is Constant-Current Driving.
In the case of Full-ON mode for ch1 to ch3, input serial data of each Constant-Voltage setting D/A Converter (DAC12
and DAC3) to be full bits high.
In the ch4, as it set Constant-Voltage mode, input serial data of Constant-Current setting D/A Converter (DACI4) to be
full bits high. As it set Constant-Current mode, input serial data of Constant-Voltage setting D/A Converter (DACV4) to
be full bits high, while as it set Full-ON mode, input serial data of both D/A Converters to be full bits high. In the
settings of Constant-Voltage or Full-ON mode, no need to connect the external resistance for output current detection
in RNF4 pin.
The selection of drive mode for ch1 to ch4 is set using serial function. (See the serial settings of the drive mode in
each channel; p.13/32 and p.15/32)
(a) Constant-Voltage mode (ch1 to ch4)
(8×VDACx≦VM[V], x = 12, 3, and V4)
･･････(1)
Output high voltage; VVOHx[V] = 8×VDACx[V]
VVOHx[V] = VM[V]
(8×VDACx＞VM[V], x = 12, 3, and V4)
･･････(2)
D/A Converter setting value; 8×VDACx[V] = 1.5 to 4.725 (DACx = 6’b01_0100 to 6’b11_1111, x = 12, 3, and V4)
In the ch4, set DACI4 = 6’b11_1111.
(b) Constant-Current mode (ch4 and ch5)
(x = I4 and 5)
･･････(3)
Output current; Ioutx[A] = VDACx[V]÷(RMETALx[Ω]＋RRNFx[Ω])
D/A Converter setting value; VDACx[V] = 0.05 to 0.315 (DACx = 6’b00_1010 to 6’b11_1111, x = I4 and 5)
RMETALx; metal impedance of BD6370GUL’s inside (ch4; RMETALI4[Ω] = 0.004(Typ.), ch5; RMETAL5[Ω] = 0.022(Typ.))
RRNFx; Resistance to connect RNFx pin for output current detection
In the ch4, set DACV4 = 6’b11_1111.
(c) Full-ON mode (ch1 to ch4)
D/A Converter setting value; DACx = 6’b11_1111
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
11/32
(x = 12, 3, V4, and I4)
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
4) Serial Input (BD6370GUL; STROBE, SCLK, and SDATA)
(1) Function Explanation
The BD6370GUL provides a 3-line serial interface for setting output modes and D/A converters.
SDATA is sent to the internal shift register during the STROBE low interval at the SCLK rising edge. Shift register data
(Bit[B] to Bit[0]) is written to the IC's internal 12-bit memory at the STROBE rising edge, according to the addresses
stored in Bit[E], Bit[D], and Bit[C]. The serial data input order is Bit[E] to Bit[0].
In the case of the resemblance drive mode (MODE13=1 and/or MODE23=1), input the serial data to be the same
condition of DAC12 and DAC3.
Be cancelled power saving mode after turned on power supply VCC and VM. Serial settings are reset when the PS
pin changes to Low-level control voltage, because of PS terminal combines power saving with serial reset function.
Serial settings are also reset when the UVLO or TSD circuit operates.
RESET period; 20μs
100%
VCC
0%
100%
PS
0%
Standby mode
Active mode
STROBE
Timing of input serial data
Timing of register data
writing to internal register
writing to internal memory
100%
0%
100%
SCLK
0%
100%
SDATA
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
0%
ADDRESS BITS
DATA BITS
PROTECT period; 50μs
Against the malfunction, it makes delay time to enable serial input in the IC
Fig.42 Sequence of Serial Control Input
(2) Serial Register Bit Map
Bit Map is consisted of 5 addresses and 60 data. It is the prohibited bit of MODExx input. Don’t input the prohibited bit
at all times. A low level should be input to the TEST bit at all times. A high signal may cause the IC to malfunction.
(a) The Prohibited Input of MODE Bit
(MODE45, MODE34, MODE23, MODE13) = (0, 0, 0, 1), (0, 0, 1, 0), (0, 0, 1, 1), (1, 0, 0, 1), (1, 0, 1, 0), (1, 0, 1, 1),
(1, 1, 0, 0), (1, 1, 0, 1), (1, 1, 1, 0), (1, 1, 1, 1)
BD6370GUL Serial Register Bit Map
No.
ADDRESS BIT
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
00H
0
0
0
TEST
TEST
MODE45
MODE34
MODE23
MODE13
MODE3C
MODE3B
MODE3A
MODE12C
MODE12B
MODE12A
01H
0
0
1
DAC12[5]
DAC12[4]
DAC12[3]
DAC12[2]
DAC12[1]
DAC12[0]
MODE5B
MODE5A
MODE4D
MODE4C
MODE4B
MODE4A
02H
0
1
0
DAC5[5]
DAC5[4]
DAC5[3]
DAC5[2]
DAC5[1]
DAC5[0]
DAC3[5]
DAC3[4]
DAC3[3]
DAC3[2]
DAC3[1]
DAC3[0]
03H
0
1
1
DACV4[5]
DACV4[4]
DACV4[3]
DACV4[2]
DACV4[1]
DACV4[0]
DACI4[5]
DACI4[4]
DACI4[3]
DACI4[2]
DACI4[1]
DACI4[0]
04H
1
0
0
TEST
TEST
IN5B
IN5A
IN4B
IN4A
IN3B
IN3A
IN2B
IN2A
IN1B
IN1A
Bit Name
BD6370GUL Serial Register Bit Function
Function
Bit Name
MODE13
MODE23
MODE34
MODE45
INxA
INxB
OUT1A-OUT3A resemblance drive select
OUT2A-OUT3B resemblance drive select
INPUT34 terminal select ch3 or ch4
INPUT45 terminal select ch4 or ch5
Control input mode select ch1 to ch5 (x=1 to 5)
Control input mode select ch1 to ch5 (x=1 to 5)
MODExA
MODExB
TEST
TEST BIT (Low level input fixed)
DACx[y]
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
MODExC
MODExC
MODExD
12/32
Function
Control input mode select ch1 to ch5 (x=1 to 5)
Control input mode select ch1 to ch5 (x=1 to 5)
Output drive select Constant-Voltage / Full-ON
mode ch1 to ch3 (x=1 to 3)
Output drive select Constant-Voltage /
Constant-Current / Full-ON mode ch4 (x=4)
6Bit D/A Converter output select ch1 to ch5
(x=12 to 5, y=0 to 5)
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
5) Serial Register Data Bit Function (BD6370GUL)
(1) ADDRESS BIT [000] Function Explanation
ADDRESS BIT
No.
00H
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
0
0
0
TEST
TEST
MODE45
MODE34
MODE23
MODE13
MODE3C
MODE3B
MODE3A
MODE12C
MODE12B
MODE12A
(a) TEST; test bit for shipment inspection
A low signal should be input to the TEST bit at all times. A high signal may cause the IC to malfunction.
(b) MODE3C and MODE12C; output drive mode select for ch1, ch2, and ch3
Bit[5]
Bit[2]
drive mode for OUTPUT terminal
MODE3C MODE12C
ch3
ch2
ch1
0
-
Full-ON
-
-
1
-
Constant-Voltage
-
-
-
0
-
Full-ON
Full-ON
-
1
-
Constant-Voltage
Constant-Voltage
Note
set DAC3=6’b11_1111
set DAC12=6’b11_1111
(c) MODE3B, MODE3A, MODE12B, and MODE12A; control input mode select for ch3, ch2, and ch1, respectively
Refer to I/O Truth Table (p.21/32 to p.22/32) for the detail logic of MODE3B, MODE3A, MODE12B, and MODE12A.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
13/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(d) MODE45, MODE34; input terminal select for ch3, ch4, and ch5, and MODE23, MODE13; resemblance drive select for
ch1, ch2, and ch3
Bit[9] Bit[8] Bit[7] Bit[6]
driven outputs for INPUTx terminal
Note
MODE45
MODE34
MODE23
MODE13
INPUT45 INPUT34 INPUT2 INPUT1
output terminal of OPEN mode Ref No.
0
0
0
0
OUT4A-OUT4B
OUT3A-OUT3B
OUT2A-OUT2B
OUT1A-OUT1B
OUT5A, OUT5B
0
0
0
1
OUT4A-OUT4B
OUT3B
OUT2A-OUT2B
OUT1A-OUT3A
OUT1B, OUT5A, OUT5B
0
0
1
0
OUT4A-OUT4B
OUT3A
OUT2A-OUT3B
OUT1A-OUT1B
OUT2B, OUT5A, OUT5B
0
0
1
1
OUT4A-OUT4B
don’t care
OUT2A-OUT3B
OUT1A-OUT3A
OUT1B, OUT2B, OUT5A, OUT5B
0
1
0
0
OUT5A-OUT5B
OUT4A-OUT4B
OUT2A-OUT2B
OUT1A-OUT1B
OUT3A, OUT3B
0
1
0
1
OUT5A-OUT5B
OUT4A-OUT4B
OUT2A-OUT2B
OUT1A-OUT3A
OUT1B, OUT3B
0
1
1
0
OUT5A-OUT5B
OUT4A-OUT4B
OUT2A-OUT3B
OUT1A-OUT1B
OUT2B, OUT3A
0
1
1
1
OUT5A-OUT5B
OUT4A-OUT4B
OUT2A-OUT3B
OUT1A-OUT3A
OUT1B, OUT2B
1
0
0
0
OUT5A-OUT5B
OUT3A-OUT3B
OUT2A-OUT2B
OUT1A-OUT1B
OUT4A, OUT4B
1
0
0
1
OUT5A-OUT5B
OUT3B
OUT2A-OUT2B
OUT1A-OUT3A
OUT1B, OUT4A, OUT4B
1
0
1
0
OUT5A-OUT5B
OUT3A
OUT2A-OUT3B
OUT1A-OUT1B
OUT2B, OUT4A, OUT4B
1
0
1
1
OUT5A-OUT5B
don’t care
OUT2A-OUT3B
OUT1A-OUT3A
OUT1B, OUT2B, OUT4A, OUT4B
1
1
0
0
don’t care
don’t care
OUT2A-OUT2B
OUT1A-OUT1B
OUT3A, OUT3B, OUT4A, OUT4B, OUT5A, OUT5B
1
1
0
1
don’t care
don’t care
OUT2A-OUT2B
OUT1A-OUT3A
OUT1B, OUT3B, OUT4A, OUT4B, OUT5A, OUT5B
1
1
1
0
don’t care
don’t care
OUT2A-OUT3B
OUT1A-OUT1B
OUT2B, OUT3A, OUT4A, OUT4B, OUT5A, OUT5B
1
1
1
1
don’t care
don’t care
OUT2A-OUT3B
OUT1A-OUT3A
OUT1B, OUT2B, OUT4A, OUT4B, OUT5A, OUT5B
1
2
3
4
5
6
-
Gray lines are prohibition serial bit; don’t input their bits at all times
ATTENTION in the case of resemblance drive mode (MODE23=1 and/or MODE13=1)
MODE3B, MODE3A, IN3B, and IN3A bits are “don’t care”. Because OUT1A-OUT3A is driven by MODE12B, MODE12A,
IN1B, and IN1A bits, and INPUT1 terminal control. In the same condition, MODE12B, MODE12A, IN2B, and IN2A bits,
and INPUT2 terminal drive OUT2A-OUT3B. And set the serial data as DAC12 = DAC3, if not, Output high voltage is
different value between OUT1A and OUT3A, and/or OUT2A and OUT3B.
INPUT1
INPUT2
ch1
OUT1A
C.V./Full ON
OUT1B
ch2
C.V./Full ON
Auto
Focus
(STM)
ch1
OUT1A
C.V./Full ON
OUT1B
OUT2A
ch2
OUT2A
OUT2B
C.V./Full ON
OUT2B
M
INPUT1
M
INPUT34
ch3
OUT3A
C.V./Full ON
OUT3B
ch4
OUT4A
C.V./C.C./Full ON
OUT4B
ch5
OUT5A
C.C.
OUT5B
INPUT45
Zoom
(DCM)
Iris
(VCM)
INPUT34
Shutter
(VCM)
INPUT45
Fig.43 Example of Standard Model
(ref No. 1, 2, and 6)
INPUT1
INPUT2
ch1
OUT1A
C.V./Full ON
OUT1B
ch2
OUT2A
C.V./Full ON
OUT2B
M
ch3
OUT3A
C.V./Full ON
OUT3B
ch4
OUT4A
C.V./C.C./Full ON
OUT4B
ch5
OUT5A
C.C.
OUT5B
ch3
OUT3A
OUT3B
ch4
OUT4A
C.V./C.C./Full ON
OUT4B
ch5
OUT5A
C.C.
OUT5B
INPUT34
INPUT45
Iris or Zoom
(STM)
Zoom or Iris
(DCM, VCM)
Shutter
(VCM)
Fig.44 Example of High Performance Model
(ref No.2 and 5)
Auto
Focus
(STM)
INPUT1
INPUT2
ch1
OUT1A
C.V./Full ON
OUT1B
ch2
OUT2A
C.V./Full ON
OUT2B
M
Zoom
(DCM)
ch3
OUT3A
C.V./Full ON
OUT3B
INPUT34
Shutter
(VCM)
other
actuator;
LED etc.
Fig.45 Example of Standard Model and 1 Actuator
(ref No.3 and 6)
Auto
Focus
(STM)
Iris
(VCM)
Iris
(VCM)
C.V./Full ON
Auto
Focus
(STM)
M
INPUT45
ch4
OUT4A
C.V./C.C./Full ON
OUT4B
ch5
OUT5A
C.C.
OUT5B
Zoom
(DCM)
Shutter
(VCM)
other
actuator;
LED etc.
Fig.46 Example of Standard Model and 1 Actuator
(ref No.4 and 6)
C.V.=Constant-Voltage drive mode, Full ON=Full-ON drive mode, and C.C.=Constant-Current drive mode
STM=Stepping Motor, DCM=DC Motor, and VCM=Voice Coil Motor
Examples of Applications above are typical. BD6370GUL is not limited to these applications.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
14/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(2) ADDRESS BIT [001] Function Explanation
ADDRESS BIT
No.
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
0
0
1
DAC12[5]
DAC12[4]
DAC12[3]
DAC12[2]
DAC12[1]
DAC12[0]
MODE5B
MODE5A
MODE4D
MODE4C
MODE4B
MODE4A
01H
(a) DAC12[5] to DAC12[0]; D/A Converter setting for output high voltage of Constant-Voltage mode in ch1 and ch2
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
DAC12 setting
Output high
DAC12[5]
DAC12[4]
DAC12[3]
DAC12[2]
DAC12[1]
DAC12[0]
voltage; VDAC12 [V]
voltage; VVOH [V]
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0.188
0.197
0.206
0.216
0.225
0.234
0.244
0.253
0.263
1.500
1.575
1.650
1.725
1.800
1.875
1.950
2.025
2.100
2.175
2.250
2.325
2.400
2.475
2.550
2.625
2.700
2.775
2.850
2.925
3.000
3.075
3.150
3.225
3.300
3.375
3.450
3.525
3.600
3.675
3.750
3.825
3.900
3.975
4.050
4.125
4.200
4.275
4.350
4.425
4.500
4.575
4.650
4.725
(b) MODE4D and MODE4C; output drive mode select for ch4
Bit[3]
Bit[2]
drive mode for ch4
MODE4D
MODE4C
0
0
1
1
0
1
0
1
Full-ON
Full-ON
Constant Voltage
Constant Current
0.272
0.281
0.291
0.300
0.309
0.319
0.328
0.338
0.347
0.356
0.366
0.375
0.384
0.394
0.403
0.413
0.422
0.431
0.441
0.450
0.459
0.469
0.478
0.488
0.497
0.506
0.516
0.525
0.534
0.544
0.553
0.563
0.572
0.581
0.591
Note
set DACV4=DACI4=6’b11_1111, and RNF4 terminal to ground
set DACV4=DACI4=6’b11_1111, and RNF4 terminal to ground
set DACI4=6’b11_1111, and RNF4 terminal to ground
set DACV4=6’b11_1111, and RNF4 terminal with resistance to ground
(c) MODE5B, MODE5A, MODE4B, and MODE4A; control input mode select for ch5 and ch4, respectively
Refer to I/O Truth Table (p.23/32) for the detail logic of MODE5B, MODE5A, MODE4B, and MODE4A.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
15/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(3) ADDRESS BIT [010] Function Explanation
ADDRESS BIT
No.
02H
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
0
1
0
DAC5[5]
DAC5[4]
DAC5[3]
DAC5[2]
DAC5[1]
DAC5[0]
Bit[5]
DAC3[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
DAC3[4]
DAC3[3]
DAC3[2]
DAC3[1]
DAC3[0]
(a) DAC5[5] to DAC5[0]; D/A Converter setting for output current (DAC5 setting voltage) of Constant-Current mode in ch5
As regards how to calculate the output current setting, refer to p.11/32 and p.24/32
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
DAC5 setting
RRNF5=0.5Ω
RRNF5=1.0Ω
Output current [mA]
DAC5[5] DAC5[4] DAC5[3] DAC5[2] DAC5[1] DAC5[0] voltage; VDAC5 [mV] Output current [mA]
0
0
1
0
1
0
50
96
49
0
0
1
0
1
1
55
105
54
0
0
1
1
0
0
60
115
59
0
0
1
1
0
1
65
125
64
0
0
1
1
1
0
70
134
68
0
0
1
1
1
1
75
144
73
0
1
0
0
0
0
80
153
78
0
1
0
0
0
1
85
163
83
0
1
0
0
1
0
90
172
88
0
1
0
0
1
1
95
182
93
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
16/32
100
105
110
115
120
125
130
135
140
145
150
155
160
165
170
175
180
185
190
195
200
205
210
215
220
225
230
235
240
245
250
255
260
265
270
275
280
285
290
295
300
305
310
315
192
201
211
220
230
239
249
259
268
278
287
297
307
316
326
336
345
355
364
374
383
393
Over Operating
Condition
98
103
108
113
117
122
127
132
137
142
147
152
157
161
166
171
176
181
186
191
196
201
205
210
216
220
225
230
235
240
245
250
254
259
264
269
274
279
284
289
294
298
303
308
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(b) DAC3[5] to DAC3[0]; D/A Converter setting for output high voltage of Constant-Voltage mode in ch3
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
DAC3 setting
Output high
DAC3[5] DAC3[4] DAC3[3] DAC3[2] DAC3[1] DAC3[0] voltage; VDAC3 [V] voltage; VVOH [V]
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
17/32
0.188
0.197
0.206
0.216
0.225
0.234
0.244
0.253
0.263
0.272
0.281
0.291
0.300
0.309
0.319
0.328
0.338
0.347
0.356
0.366
0.375
0.384
0.394
0.403
0.413
0.422
0.431
0.441
0.450
0.459
0.469
0.478
0.488
0.497
0.506
0.516
0.525
0.534
0.544
0.553
0.563
0.572
0.581
0.591
1.500
1.575
1.650
1.725
1.800
1.875
1.950
2.025
2.100
2.175
2.250
2.325
2.400
2.475
2.550
2.625
2.700
2.775
2.850
2.925
3.000
3.075
3.150
3.225
3.300
3.375
3.450
3.525
3.600
3.675
3.750
3.825
3.900
3.975
4.050
4.125
4.200
4.275
4.350
4.425
4.500
4.575
4.650
4.725
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(4) ADDRESS BIT [011] Function Explanation
ADDRESS BIT
No.
03H
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
0
1
1
DACV4[5]
DACV4[4]
DACV4[3]
DACV4[2]
DACV4[1]
DACV4[0]
DACI4[5]
DACI4[4]
DACI4[3]
DACI4[2]
DACI4[1]
DACI4[0]
(a) DACV4[5] to DACV4[0]; D/A Converter setting for output high voltage of Constant-Voltage mode in ch4
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
DACV4 setting
Output high
DACV4[5]
DACV4[4]
DACV4[3]
DACV4[2]
DACV4[1]
DACV4[0]
voltage; VDACV4 [V]
voltage; VVOH [V]
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0.188
0.197
0.206
0.216
0.225
0.234
0.244
0.253
0.263
1.500
1.575
1.650
1.725
1.800
1.875
1.950
2.025
2.100
2.175
2.250
2.325
2.400
2.475
2.550
2.625
2.700
2.775
2.850
2.925
3.000
3.075
3.150
3.225
3.300
3.375
3.450
3.525
3.600
3.675
3.750
3.825
3.900
3.975
4.050
4.125
4.200
4.275
4.350
4.425
4.500
4.575
4.650
4.725
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
18/32
0.272
0.281
0.291
0.300
0.309
0.319
0.328
0.338
0.347
0.356
0.366
0.375
0.384
0.394
0.403
0.413
0.422
0.431
0.441
0.450
0.459
0.469
0.478
0.488
0.497
0.506
0.516
0.525
0.534
0.544
0.553
0.563
0.572
0.581
0.591
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(b) DACI4[5] to DACI4[0]; D/A Converter setting for output current (DACI4 setting voltage) of Constant-Current mode in ch4
As regards how to calculate the output current setting, refer to p.11/32 and p.24/32
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
DACI4 setting
RRNFI4=0.5Ω
RRNFI4=1.0Ω
Output current [mA]
DACI4[5] DACI4[4] DACI4[3] DACI4[2] DACI4[1] DACI4[0] voltage; VDACI4 [mV] Output current [mA]
0
0
1
0
1
0
50
99
50
0
0
1
0
1
1
55
109
55
0
0
1
1
0
0
60
119
60
0
0
1
1
0
1
65
129
65
0
0
1
1
1
0
70
139
70
0
0
1
1
1
1
75
149
75
0
1
0
0
0
0
80
159
80
0
1
0
0
0
1
85
169
85
0
1
0
0
1
0
90
179
90
0
1
0
0
1
1
95
188
95
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
19/32
100
105
110
115
120
125
130
135
140
145
150
155
160
165
170
175
180
185
190
195
200
205
210
215
220
225
230
235
240
245
250
255
260
265
270
275
280
285
290
295
300
305
310
315
198
208
218
228
238
248
258
268
278
288
298
308
317
327
337
347
357
367
377
387
397
Over Operating
Condition
100
105
110
115
120
125
129
134
139
144
149
154
159
164
169
174
179
184
189
194
199
204
209
214
219
224
229
234
239
244
249
254
259
264
269
274
279
284
289
294
299
304
309
314
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(5) ADDRESS BIT [100] Function Explanation
ADDRESS BIT
No.
04H
DATA BIT
Bit[E]
Bit[D]
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
1
0
0
TEST
TEST
IN5B
IN5A
IN4B
IN4A
IN3B
IN3A
IN2B
IN2A
IN1B
IN1A
(a) TEST; test bit for shipment inspection
A low signal should be input to the TEST bit at all times. A high signal may cause the IC to malfunction.
(b) IN5B to IN1A; control input mode select for ch1 to ch5, respectively
Refer to I/O Truth Table (p.21/32 to p.23/32) for the detail logic of IN1A to IN5B.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
20/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
6) I/O Truth Table (BD6370GUL)
(1) I/O truth table for ch1 and ch2, in the case of MODE13=0, MODE23=0 (x=1 or 2)
Serial interface input bit
Terminal
Output terminal
MODE12B
MODE12A
INxB
INxA
INPUTx
OUTxA
OUTxB
PWM Drive Mode by INPUTx terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUTx terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUTx terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUTx terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
MODE
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care
At CW, current flows from OUTxA to OUTxB. At CCW, current flows from OUTxB to OUTxA.
(2) I/O truth table for ch3, in the case of MODE34=0, MODE13=0, and MODE23=0
Serial interface input bit
Terminal
Output terminal
MODE3B MODE3A
IN3B
IN3A
INPUT34 OUT3A
OUT3B
PWM Drive Mode by INPUT34 terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUT34 terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUT34 terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUT34 terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
MODE
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care
At CW, current flows from OUT3A to OUT3B. At CCW, current flows from OUT3B to OUT3A.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
21/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(3) I/O truth table for ch1, ch3, in the case of MODE13=1 (OUT1A-OUT3A resemblance drive mode)
Serial interface input bit
Terminal
Output terminal
MODE
MODE12B
MODE12A
IN1B
IN1A
INPUT1
OUT1A
OUT3A
PWM Drive Mode by INPUT1 terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUT1 terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUT1 terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUT1 terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care, OUT1B; Hi impedance
At CW, current flows from OUT1A to OUT3A. At CCW, current flows from OUT3A to OUT1A.
(4) I/O truth table for ch2, ch3, in the case of MODE23=1 (OUT2A-OUT3B resemblance drive mode)
Serial interface input bit
Terminal
Output terminal
MODE
MODE12B
MODE12A
IN2B
IN2A
INPUT2
OUT2A
OUT3B
PWM Drive Mode by INPUT2 terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUT2 terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUT2 terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUT2 terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care, OUT2B; Hi impedance
At CW, current flows from OUT2A to OUT3B. At CCW, current flows from OUT3B to OUT2A.
ATTENTION in the case of resemblance drive mode (MODE23=1 and/or MODE13=1)
MODE3B, MODE3A, IN3B, and IN3A bits are “don’t care”. Because OUT1A-OUT3A is driven by MODE12B, MODE12A,
IN1B, and IN1A bits, and INPUT1 terminal control. In the same condition, MODE12B, MODE12A, IN2B, and IN2A bits,
and INPUT2 terminal drive OUT2A-OUT3B. And set the serial data as DAC12 = DAC3, if not, Output high voltage is
different value between OUT1A and OUT3A, and/or OUT2A and OUT3B.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
22/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
(5) I/O truth table for ch4, in the case of MODE45=0 (if MODE34=0, then x=45, else then x=34)
Serial interface input bit
Terminal
Output terminal
MODE
MODE4B MODE4A
IN4B
IN4A
INPUTx
OUT4A
OUT4B
PWM Drive Mode by INPUTx terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUTx terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUTx terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUTx terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care
At CW, current flows from OUT4A to OUT4B. At CCW, current flows from OUT4B to OUT4A.
(6) I/O truth table for ch5, in the case of MODE45=1, MODE34=0 (or MODE45=0, MODE34=1)
Serial interface input bit
Terminal
Output terminal
MODE
MODE5B MODE5A
IN5B
IN5A
INPUT45 OUT5A
OUT5B
PWM Drive Mode by INPUT45 terminal
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
PWM Drive Mode by INPUT45 terminal
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
CW / CCW Drive Mode by INPUT45 terminal
1
0
X
0
1
0
0
1
1
0
0
1
1
0
1
1
CW / CCW Drive Mode by INPUT45 terminal
1
1
X
0
1
1
0
1
1
1
0
1
1
1
1
1
X
L
H
L
H
X
Z
L
H
L
L
L
Z
L
L
L
H
L
OFF
Brake
CW
Brake
CCW
Brake
X
L
H
L
H
X
Z
H
L
L
L
L
Z
L
L
H
L
L
OFF
CW
Brake
CCW
Brake
Brake
X
L
H
X
Z
L
H
L
Z
H
L
L
OFF
CCW
CW
Brake
X
L
H
X
Z
H
L
L
Z
L
H
L
OFF
CW
CCW
Brake
H; High level, L; Low level, Z; Hi impedance, X; Don’t care
At CW, current flows from OUT5A to OUT5B. At CCW, current flows from OUT5B to OUT5A.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
23/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
7) The More Precise Constant-Current Settings (BD6370GUL)
Regarding Constant-Current Drive blocks (ch4 and ch5), there is the metal impedance of each RNF in BD6370GUL inside:
4mΩ (Typ.) and 22mΩ (Typ.), respectively. Then the metal impedances and the board patterning impedances of RNF4 and
RNF5 lines considered, set each D/A Converter to drive the actuator in the more precise constant current.
BD6370GUL
Board Ground
1～100uF
Constant Current Drive block (ch4 and ch5)
VM
OUT4A
Level Shift
H br idge
&
C.V./C.C./F ull ON
Pre Driver
OUT4B
RNF4
6bit DACI4
V DACI 4
C.C.
Pre Driver
6bit DAC5
A1
RRNFI4
RW4_ 2
RRNF 5
RW5_ 2
C1
IO UT5
OUT5B D1
RNF5
VDAC5
IO UT4
B1
RW4 _1
H bridge
&
A2
RM ET AL I4
=4mΩ (Typ.)
OUT5A
Level Shift
A3
E1
RM ET AL 5
=22mΩ (Typ.)
RW5 _1
RRNFx;
RMETALx ;
external component of output current detection
metal impedance of BD6370GUL’s inside
RWx_1, 2;
VDACx;
IOUTx;
board patterning impedance
setting value of constant current
current flowed through the motor
Fig.47 Metal Impedance and Board Patterning Impedance of Constant-Current block
The more correct D/A Converter settings of Constant-Current H-bridge (ch4 and ch5)
Output current value; IOUTx[A] = VDACx[V]÷(RRNFx[Ω]＋RMETALx[Ω]＋RWx_1[Ω]＋RWx_2[Ω])
(ex.) If there are VDACx=0.1[V], RRNFx=0.5[Ω], and RWx_1＋RWx_2=0[Ω] (the ideal patterning condition), then
Output current value (ch4); IOUT4[A] = 0.1[V]÷(0.5[Ω]＋0.004[Ω]＋0[Ω]) = 0.198
Output current value (ch5); IOUT5[A] = 0.1[V]÷(0.5[Ω]＋0.022[Ω]＋0[Ω]) = 0.191
Else if there are VDACx=0.1[V], RRNFx= 0.5[Ω], and RWx_1＋RWx_2=0.05[Ω] (the more closely real patterning
condition; the value is different to the patterning), then
Output current value (ch4); IOUT4[A] = 0.1[V]÷(0.5[Ω]＋0.004[Ω]＋0.05[Ω]) = 0.181
Output current value (ch5); IOUT5[A] = 0.1[V]÷(0.5[Ω]＋0.022[Ω]＋0.05[Ω]) = 0.175
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
24/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
8) Application control sequences (BD6370GUL)
(1) Stepping Motor drive controlled by 2 phases mode
100%
VCC
0%
100%
PS
0%
100%
STROBE
0%
100%
SCLK
0%
100%
SDATA
(i)
(ii)
(iii)
(iv)
(v)
(vi)
0%
(vii)
100%
INPUT1
0%
100%
INPUT2
0%
100%
OUT1A [V]
0%
100%
OUT1B [V]
0%
100%
OUT2A [V]
0%
100%
OUT2B [V]
0%
100%
OUT1A-1B [A]
0%
-100%
100%
OUT2A-2B [A]
0%
-100%
1
; Don’t care
2
3
; Hi impedance
1
4
2
3
4
1
4
3
Forward
2
1
4
3
2
1
Reverse
Fig.48 Timing Chart of Stepping Motor Drive
Sequence of Stepping Motor Drive
Terminal
Output terminal
Serial interface input bit
MODE
12B
MODE
12A
IN2B
MODE
IN2A
IN1B
IN1A
INPUT1
INPUT2
OUT1A
OUT1B
OUT2A
OUT2B
0
0
0
X
X
Z
Z
Z
Z
ch1
ch2
Position
Control standby
1
0
0
Start 2 phase mode driving
1
0
0
1
0
1
H
H
H
L
H
L
CW
CW
1
1
0
0
1
0
1
H
L
H
L
L
H
CW
CCW
2
1
0
0
1
0
1
L
L
L
H
L
H
CCW
CCW
3
1
0
0
1
0
1
L
H
L
H
H
L
CCW
CW
4
1
0
0
1
0
1
H
H
H
L
H
L
CW
CW
1
1
0
0
1
0
1
H
H
H
L
H
L
CW
CW
1
1
0
0
1
0
1
L
H
L
H
H
L
CCW
CW
4
1
0
0
1
0
1
L
L
L
H
L
H
CCW
CCW
3
1
0
0
1
0
1
H
L
H
L
L
H
CW
CCW
2
1
0
0
1
0
1
H
H
H
L
H
L
CW
CW
1
0
0
X
X
Z
Z
Z
Z
Forward
Reverse
End timing (control standby)
1
0
0
0
H; High level, L; Low level, Z; Hi impedance, X; Don’t care
At CW, current flows from OUTxA to OUTxB. At CCW, current flows from OUTxB to OUTxA.
At Forward; position up from “1” to “4”. At Reverse; position down from “4” to “1”.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
25/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
In Fig.49, it shows minimum step angle, and the relation between size and direction of the current to motor.
CW
OUT2A
2
Forwar
d
1
OUT1B
CCW
OUT1A
CW
3
4
OUT2B
CCW
Revers
Fig.49 Torque Vector of 2 Phases Mode
Serial Control Input from Initial Set Up (i) to End Timing (vii)
ADDRESS BIT
No.
Bit[E]
Bit[D]
DATA BIT
Bit[C]
Bit[B]
Bit[A]
Bit[9]
Bit[8]
Bit[7]
Bit[6]
Bit[5]
Bit[4]
Bit[3]
Bit[2]
Bit[1]
Bit[0]
Initial set up
(i) ADDRESS BIT [000]; set ch1 and ch2; Constant-Voltage drive mode
00H
0
0
TEST
TEST
MODE45
MODE34
MODE23
MODE13
MODE3C
MODE3B
MODE3A
MODE12C
MODE12B
MODE12A
0
0
0
0
0
0
0
0
0
1
1
0
0
(ii) ADDRESS BIT [001]; set Output high voltage=3.0V for ch1 and ch2
01H
0
0
DAC12[5]
DAC12[4]
DAC12[3]
DAC12[2]
DAC12[1]
DAC12[0]
MODE5B
MODE5A
MODE4D
MODE4C
MODE4B
MODE4A
1
0
1
0
0
0
0
0
0
0
0
0
1
(iii) ADDRESS BIT [010]; in this case, don’t care
02H
0
1
DAC5[5]
DAC5[4]
DAC5[3]
DAC5[2]
DAC5[1]
DAC5[0]
DAC3[4]
DAC3[3]
DAC3[2]
DAC3[1]
DAC3[0]
0
0
0
0
0
0
DAC3[5]
0
0
0
0
0
0
0
(iv) ADDRESS BIT [011]; in this case, don’t care
03H
0
1
DACV4[5]
DACV4[4]
DACV4[3]
DACV4[2]
DACV4[1]
DACV4[0]
DACI4[5]
DACI4[4]
DACI4[3]
DACI4[2]
DACI4[1]
DACI4[0]
0
0
0
0
0
0
0
0
0
0
0
0
1
(v) ADDRESS BIT [100]; set control standby mode
04H
1
0
TEST
TEST
IN5B
IN5A
IN4B
IN4A
IN3B
IN3A
IN2B
IN2A
IN1B
IN1A
0
0
0
0
0
0
0
0
0
0
0
0
TEST
TEST
IN5B
IN5A
IN4B
IN4A
IN3B
IN3A
IN2B
IN2A
IN1B
IN1A
0
0
0
0
0
0
0
0
0
1
0
1
TEST
TEST
IN5B
IN5A
IN4B
IN4A
IN3B
IN3A
IN2B
IN2A
IN1B
IN1A
0
0
0
0
0
0
0
0
0
0
0
0
0
Start timing
(vi) ADDRESS BIT [100]
04H
1
0
0
End timing
(vii) ADDRESS BIT [100]
04H
1
0
0
The above Sequence is one example. BD6370GUL is not limited to this sequence.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
26/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●BD6758MWV and BD6758KN Function Explanation
Bypass filter Capacitor for
power supply input. (p.29/32)
1～100uF
Power-saving (p.27/32)
H : Active
L : Standby
VCC
Bypass filter Capacitor for
power supply input. (p.29/32)
4
PS 35
Power Save
TSD & UVLO
BandGap
Motor control input
(p.27/32)
H bridge
IN1A 36
IN1B 1
Level Shift
Logic12
IN2A 2
Drive mode selection
(p.27/32)
H : EN/IN
L : IN/IN
1～100uF
31
Full ON
&
Pre Driver
H bridge
IN2B 3
Full ON
SEL1 28
29
30
33
34
32
VM1
OUT1A
OUT1B
M
OUT2A
Bypass filter Capacitor for
power supply input. (p.29/32)
OUT2B
PGND1
1～100uF
Motor control input
(p.27/32)
14
H bridge
IN3A 6
IN3B 7
Drive mode selection
(p.27/32)
H : EN/IN
L : IN/IN
Level Shift
Logic34
IN4A 8
Full ON
&
Pre Driver
H bridge
IN4B 9
Full ON
SEL2 18
Motor
control input
モータ制御入力
brake
function
ブレーキ機能(p.?/32)
(p.27/32)
H : ブレーキ
H : Brake
12
13
16
17
15
BRK1 10
VM2
OUT3A
OUT3B
M
OUT4A
Bypass filter Capacitor for
power supply input. (p.29/32)
OUT4B
PGND2
1～100uF
BRK2 11
24
VM3
EN1 27
Level Shift
Logic5
IN5 26
H bridge
&
Const. Current
Pre Driver
21
25
23
Motor control input
(p.27/32)
VREF
22
20
19
VREF
When using the VREF voltage (1.2V)
resistance division value as VLIM input
value, select R1 and R2 values such that,
2kΩ≦R1+R2≦20kΩ (p.28/32)
OUT5B
RNF
0.1Ω~5.0Ω
SENSE
5
VLIM
R1
OUT5A
GND
R2
The output current is converted to a voltage with
the RNF external resistor and transmitted to the
SENSE pin. (p.28/32)
Iout[A] = VLIM[V]÷RNF[Ω]
Fig.50 BD6758MWV / KN Application Circuit Diagram
1) Power-saving function (BD6758MWV / KN)
When Low-level voltage is applied to PS pin, the IC will be turned off internally and the circuit current will be 0μA (Typ.).
During operating mode, PS pin should be High-level. (See the Electrical Characteristics; p.6/32)
2) Control input (BD6758MWV / KN)
(1) INxA, INxB, EN1 and IN5 pins
These pins are used to program and control the motor drive modes. (See the Electrical Characteristics; p.6/32 and I/O
Truth Table; p.28/32)
(2) SELx pins
When the Low-level voltage is applied to the SEL pin, the I/O logic can be set to EN/IN mode. However, when the
High-level voltage is applied, the I/O logic can be set to IN/IN mode. (See the Electrical Characteristics; p.6/32 and I/O
Truth Table; p.28/32)
(3) BRKx pins
Applying the High-level voltage to the BRKx pin will set the brake mode. (See the Electrical Characteristics; p.6/32
and I/O Truth Table; p.28/32)
3) H-bridge (BD6758MWV / KN)
The 5-channel H-bridges can be controlled independently. For this reason, it is possible to drive the H-bridges
simultaneously, as long as the package thermal tolerances are not exceeded.
The H-bridge output transistors of BD6758MWV and BD6758KN are Power CMOS Drivers. The total H-bridge
ON-Resistance on the high and low sides varies with the VM voltage. The system must be designed so that the maximum
H-bridge current for each channel is 800mA or below. (See the Operating Conditions; p.2/32)
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
27/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
4) Drive system of Linear Constant-Current H-bridge (BD6758MWV / KN: ch5)
BD6758MWV / KN (ch5) enable Linear Constant-Current Driving.
(1) Reference voltage output (with a tolerance of ±3%)
The VREF pin outputs 1.2V, based on the internal reference voltage. The output current of the Constant-Current Drive
block is controllable by connecting external resistance to the VREF pin of the IC and applying a voltage divided by the
resistor to the output current setting pins (VLIM pin). It is recommended to set the external resistance to 2kΩ or above
in consideration of the current capacity of the VREF pin, and 20kΩ or below in order to minimize the fluctuation of the
set value caused by the base current of the internal transistor of the IC.
(2) Output current detection and current settings
By connecting external resistor (0.1Ω to 5.0Ω) to the RNF pin of the IC, the motor drive current will be converted into
voltage in order to be detected. The output current is kept constant by shorting the RNF and SENSE pins and
comparing the voltage with the VLIM voltage. To perform output current settings more precisely, trim the external RNF
resistance if needed, and supply a precise voltage externally to the VLIM pin of the IC. In that case, open the VREF
pin.
Output
current
value
VLIM[V]
RNF[Ω]
The output current is 400mA3% if 0.2V is applied to the VLIM pin and a 0.5Ω resistor is connected externally to the
RNF pin.
If the VLIM pin is shorted to the VCC pin (or the same voltage level as the VCC is applied) and the SENSE and RNF
pins are shorted to the ground, this channel can be used as a Full-ON Drive H-bridge like the other four channels of
BD6758KN.
5) I/O truth table (BD6758MWV / KN)
Drive
mode
EN/IN
IN/IN
BD6758MWV / KN Full-ON Driver ch1 and ch2 I/O Truth Table
INPUT
OUTPUT
SEL1
INxA
INxB
OUTxA
OUTxB
H
X
Z
Z
L
L
L
H
L
L
H
L
H
L
L
Z
Z
H
L
H
L
H
L
H
L
H
H
H
L
L
Output mode
Standby
CW
CCW
Standby
CW
CCW
Brake
L: Low, H: High, X: Don’t care, Z: High impedance
At CW, current flows from OUTA to OUTB. At CCW, current flows from OUTB to OUTA.
Drive
mode
EN/IN
IN/IN
BD6758MWV / KN Full-ON Driver ch3 and ch4 I/O Truth Table
INPUT
OUTPUT
SEL2
INxA
INxB
BRKx
OUTxA
OUTxB
H
X
X
Z
Z
L
L
L
H
L
L
L
H
L
L
H
L
X
H
L
L
L
L
X
Z
Z
H
L
X
H
L
H
L
H
X
L
H
H
H
X
L
L
Output mode
Standby
CW
CCW
Brake
Standby
CW
CCW
Brake
L: Low, H: High, X: Don’t care, Z: High impedance
At CW, current flows from OUTA to OUTB. At CCW, current flows from OUTB to OUTA.
Drive
mode
EN/IN
BD6758MWV / KN Linear Constant-Current Driver ch5 I/O Truth Table
INPUT
OUTPUT
Output mode
EN1
IN5
OUT5A
OUT5B
H
X
Z
Z
Standby
L
L
H
L
CW
L
H
L
H
CCW
L: Low, H: High, X: Don’t care, Z: High impedance
At CW, current flows from OUTA to OUTB. At CCW, current flows from OUTB to OUTA.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
28/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●I/O Circuit Diagram
8
PS, INPUT1, 2, 34, 45※ ,
9
STROBE, SCLK, SDATA※
VCC
VM, GND,
OUT1A, 1B, 2A, 2B, 3A, 3B
VCC
VM, RNF4, OUT4A, 4B
VM
VM, RNF5, OUT5A, 5B
VM
VM
OUT4A
OUT4B
OUT5A
OUT5B
10kΩ
20kΩ
140kΩ
※8
20kΩ
OUTxA
OUTxB
100kΩ
9
200kΩ※
140kΩ
22mΩ RNF5
4mΩ RNF4
PGND
Fig.51 BD6370GUL I/O Circuit Diagram (Resistance values are typical ones)
PS, INxA, INxB, EN1, IN5, SELx,
BRKx
VCC
VMx, OUTxA, OUTxB, PGNDx, RNF
VCC
10kΩ
VREF
VMx
VCC
VLIM, SENSE
VCC
VCC
1kΩ
OUTxA
OUTxB
100kΩ
PGNDx
RNF
200kΩ
Fig.52 BD6758MWV / KN I/O Circuit Diagram (Resistance values are typical ones)
●Notes for use
1) Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may
result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such
damage is suffered. The implementation of a physical safety measure such as a fuse should be considered when use of
the IC in a special mode where the absolute maximum ratings may be exceeded is anticipated.
2) Storage temperature range
As long as the IC is kept within this range, there should be no problems in the IC’s performance. Conversely, extreme
temperature changes may result in poor IC performance, even if the changes are within the above range.
3) Power supply pins and lines
None of the VM line for the H-bridges is internally connected to the VCC power supply line, which is only for the control logic or
analog circuit. Therefore, the VM and VCC lines can be driven at different voltages. Although these lines can be connected to a
common power supply, do not open the power supply pin but connect it to the power supply externally.
Regenerated current may flow as a result of the motor's back electromotive force. Insert capacitors between the power supply
and ground pins to serve as a route for regenerated current. Determine the capacitance in full consideration of all the
characteristics of the electrolytic capacitor, because the electrolytic capacitor may loose some capacitance at low temperatures.
If the connected power supply does not have sufficient current absorption capacity, regenerative current will cause the voltage
on the power supply line to rise, which combined with the product and its peripheral circuitry may exceed the absolute maximum
ratings. It is recommended to implement a physical safety measure such as the insertion of a voltage clamp diode between the
power supply and ground pins.
For this IC with several power supplies and a part consists of the CMOS block, it is possible that rush current may flow
instantaneously due to the internal powering sequence and delays, and to the unstable internal logic, respectively. Therefore,
give special consideration to power coupling capacitance, width of power and ground wirings, and routing of wiring.
4) Ground pins and lines
Ensure a minimum GND pin potential in all operating conditions. Make sure that no pins are at a voltage below the GND at
any time, regardless of whether it is a transient signal or not.
When using both small signal GND and large current MGND patterns, it is recommended to isolate the two ground
patterns, placing a single ground point at the application's reference point so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the
GND wiring pattern of any external components, either.
The power supply and ground lines must be as short and thick as possible to reduce line impedance.
5) Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
29/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
6) Pin short and wrong direction assembly of the device
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if positive and ground power supply terminals are reversed. The IC may also be damaged if pins are
shorted together or are shorted to other circuit’s power lines.
7) Actions in strong magnetic field
Use caution when using the IC in the presence of a strong magnetic field as doing so may cause the IC to malfunction.
8) ASO
When using the IC, set the output transistor for the motor so that it does not exceed absolute maximum ratings or ASO.
9) Thermal shutdown circuit
If the junction temperature (Tjmax) reaches 175°C, the TSD circuit will operate, and the coil output circuit of the motor will
open. There is a temperature hysteresis of approximately 25°C (BD6373GW and BD6873KN Typ.) and 25°C (BD6753KV
Typ.). The TSD circuit is designed only to shut off the IC in order to prevent runaway thermal operation. It is not designed
to protect the IC or guarantee its operation. The performance of the IC’s characteristics is not guaranteed and it is
recommended that the device is replaced after the TSD is activated.
10) Serial data input
In the BD6370GUL, SDATA input string start with MSB first. A low level should be input to the TEST bit at all times. A high signal
may cause the IC to malfunction. The serial settings are reset during standby mode operation and whenever the UVLO or TSD
circuits are operating.
It is the prohibited bit of MODExx input. Don’t input the prohibited bit at all times. (See the Serial Register Bit Map; p.12/32)
In the case of the resemblance drive mode (MODE13=1 and/or MODE23=1), MODE3B, MODE3A, IN3B, and IN3A bits are
“don’t care”. Because OUT1A-OUT3A is driven by MODE12B, MODE12A, IN1B, and IN1A bits, and INPUT1 terminal control. In
the same condition, MODE12B, MODE12A, IN2B, and IN2A bits, and INPUT2 terminal drive OUT2A-OUT3B. And set the serial
data as DAC12 = DAC3, if not, Output high voltage is different value between OUT1A and OUT3A, and/or OUT2A and OUT3B.
In the case of Full-ON mode for ch1 to ch3,input serial data of each Constant-Voltage setting D/A Converter (DAC12 and DAC3)
to be full bits high.
In the ch4, as it set Constant-Voltage mode, input serial data of Constant-Current setting D/A Converter (DACI4) to be full bits
high. As it set Constant-Current mode, input serial data of Constant-Voltage setting D/A Converter (DACV4) to be full bits high,
while as it set Full-ON mode, input serial data of both D/A Converters to be full bits high. In the settings of Constant-Voltage or
Full-ON mode, no need to connect the external resistance for output current detection in RNF4 pin.
11) Power saving terminal
Be cancelled power saving mode after turned on power supply VCC and VM, because of PS terminal combines power
saving with serial reset function. If the case of power saving terminal always shorted power supply terminal, reset function
may not be well, and it may cause the IC to malfunction.
12) Testing on application board
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to, or
removing it from a jig or fixture, during the inspection process. Ground the IC during assembly steps as an antistatic
measure. Use similar precaution when transporting and storing the IC.
13) Application example
The application circuit is recommended for use. Make sure to confirm the adequacy of the characteristics. When using the
circuit with changes to the external circuit constants, make sure to leave an adequate margin for external components
including static and transitional characteristics as well as dispersion of the IC.
14) Regarding input pin of the IC
+
This monolithic IC contains P isolation and P substrate layers between adjacent elements to keep them isolated. P-N
junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic diode or
transistor. For example, the relation between each potential is as follows:
When GND > Pin A, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic diode and transistor.
Parasitic elements can occur inevitably in the structure of the IC. The operation of parasitic elements can result in mutual
interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic elements
operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used.
Resistor
Pin A
Pin B
C
Transistor (NPN)
B
E
Pin A
N
P
+
N
P
P
N
+
N
Parasitic
element
P+
P substrate
Parasitic element
GND
Pin B
B
N
P
P
C
+
N
E
Parasitic
element
P substrate
Parasitic element
GND
GND
Other adjacent
elements
GND
Fig.53 Example of Simple IC Architecture
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
30/32
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
●Ordering part number
B
D
6
Part No.
3
7
0
Part No.
6370 :C.V./F.ON 3ch
+C.V./C.C./F.ON 1ch
+C.C. 1ch
6758 :F.ON 4ch+C.C. 1ch
G
U
L
-
Package
GUL : VCSP50L2
MWV : UQFN036V5050
KN
: VQFN36
E
2
Packaging and forming specification
E2: Embossed tape and reel
VCSP50L2 (BD6360GUL)
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
1pin
(Unit:mm)
Reel
)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
UQFN036V5050
<Tape and Reel information>
5.0 ± 0.1
5.0±0.1
1.0MAX
2500pcs
9
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
(0.22)
+0.03
0.02 -0.02
S
0.08 S
2.7±0.1
C0.2
10
2.7± 0.1
36
0.5 ± 0.1
Embossed carrier tape
Quantity
Direction
of feed
1PIN MARK
1
Tape
28
18
27
0.9
19 +0.05
0.4 0.2 -0.04
1pin
(Unit : mm)
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
Reel
31/32
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2009.06 - Rev.A
Technical Note
BD6370GUL, BD6758MWV, BD6758KN
VQFN36
6.2 ± 0.1
6.0 ± 0.1
36
0.22±0.05
0.22 ± 0.05
1
Tape
Embossed carrier tape (with dry pack)
18
Quantity
2500pcs
10
Direction
of feed
19
28
9
0.08
M
+0.03
0.02 -0.02
6.2±0.1
6.0±0.1
27
<Tape and Reel information>
+0.1
0.6 -0.3
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
0.95MAX
(1.1)
0.05
5
.3
(0
3(0
.2
2
)
)
5)
.
(0
0.5
Notice :
Do not use the dotted line area
for soldering
(Unit : mm)
www.rohm.co
© 2009 ROHM Co., Ltd. All rights reserved.
1pin
Reel
32/32
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2009.06 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039A

Open as PDF

Similar pages