IBC Module IB0xxQ096T70xx-xx ® S US C C NRTL US 5:1 Intermediate Bus Converter Module: Up to 750W Output Features & Benefits Size: 2.30 x 1.45 x 0.42in 58.4 x 36.8 x 10.6mm • Input: 36 – 60VDC (38 – 55VDC for IB048x) • Low profile: 0.42” height above board • Output: 9.6VDC at 48VIN • Industry standard 1/4 Brick pinout • Output current up to 70A • Sine Amplitude Converter™ (SAC™) • Output power: up to 750W * • Low noise 1MHz ZVS/ZCS • 2250VDC isolation (1500VDC isolation for IB048x) • 98.2% peak efficiency * Lower power model available Product Description Typical Applications The Intermediate Bus Converter (IBC) Module is a very efficient, low profile, isolated, fixed ratio converter for power system applications in enterprise and optical access networks. Rated at up to 530W from 38VIN and up to 750W from 55VIN, the IBC conforms to an industry standard quarter-brick footprint while supplying power greatly exceeding competitive quarter-bricks. Its leading efficiency enables full load operation at 50°C with only 400LFM airflow. Its small cross section facilitates unimpeded airflow — above and below its thin body — to minimize the temperature rise of downstream components. A baseplate option is available for alternative cooling schemes. • Enterprise networks • Optical access networks • Storage networks • Automated test equipment Part Ordering Information Product Function I B Input Voltage 0 x IB = Intermediate Bus Converter 048 = 38 – 55VDC 050 = 36 – 60VDC 054 = 36 – 60VDC * Output Voltage (Nom.) x 10 Package x Q 0 Q = Quarter Brick Format 9 Temperature Grade 6 T Output Current 7 T = -40ºC ≤ TOPERATING ≤ +100ºC -40ºC ≤ TSTORAGE ≤ +125ºC 096 = (VOUT nominal @ VIN = 48VDC x 10 (5:1 transfer ratio) Rev 1.2 09/2016 Pin Length x x vicorpower.com 800 927.9474 Options – x x 00 = Open frame BP = Baseplate N = Negative P = Positive 70 = Max Rated Output Current * Operating transient to 75VDC IBC Module Page 1 of 18 0 Enable Logic 1 = 0.145” 2 = 0.210” 3 = 0.180” IB0xxQ096T70xx-xx Absolute Maximum Ratings The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause permanent damage to the device. Parameter Comments Input voltage (+IN to –IN) See Input Range Specific Characteristics for details Min Max Unit -0.5 75 VDC 5 V / µs -0.5 20 VDC -0.5 (see note) VDC 70 A Input voltage slew rate EN to –IN Output voltage (+OUT to –OUT) See OVP setpoint max Output current POUT ≤ 750W Dielectric withstand Input to output 1min 2250 1500 for IB048x Output to baseplate 1min 707 Hottest semiconductor -40 125 Operating baseplate -40 100 Storage -55 125 VDC Temperature Operating junction ºC Electrical Specifications Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit 38 48 55 VDC Input Range Specific Characteristics Part Number IB048Q096T70xx-xx Operating input voltage Non-operating input surge withstand < 100ms 75 VDC 0.003 5 V / µs Turn–on 33 38 VDC Turn–off 31 36 VDC Turn–on / turn–off hysteresis 2 Operating input dV / dt Undervoltage protection VDC Time constant Undervoltage blanking time UV blanking time is enabled after start up 50 100 7 µs 200 µs Overvoltage protection Turn–off 60 64 VDC Turn–on 55 64 VDC 4 µs 11.0 VDC 12.8 VDC Time constant DC output voltage band No load, over VIN range 7.6 Output OVP set point Module will shut down 12.0 Input to output and input to baseplate; 1min 1500 Output to baseplate 707 Dielctric withstand Insulation resistance IBC Module Page 2 of 18 Input to output Rev 1.2 09/2016 9.6 VDC 30 vicorpower.com 800 927.9474 MΩ IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit 36 48 60 VDC 75 VDC 0.003 5 V / µs Turn–on 31 36 VDC Turn–off 29 34 VDC Turn–on / turn–off hysteresis 2 Input Range Specific Characteristics Part Number IB050Q096T70xx-xx Operating input voltage Non-operating input surge withstand < 100ms Operating input dV / dt Undervoltage protection VDC Time constant Undervoltage blanking time UV blanking time is enabled after start up 50 100 7 µs 200 µs Overvoltage protection Turn–off 65 69 VDC Turn–on 60 69 VDC 4 µs 12.0 VDC 13.8 VDC Time constant DC output voltage band No load, over VIN range 7.2 Output OVP set point Module will shut down 13 Dielctric withstand Insulation resistance IBC Module Page 3 of 18 Input to output and input to baseplate; 1min 2250 Output to baseplate 707 Input to output Rev 1.2 09/2016 9.6 VDC 30 vicorpower.com 800 927.9474 MΩ IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit 36 48 60 VDC Input Range Specific Characteristics Part Number IB054Q096T70xx-xx Operating input voltage Non-operating input surge withstand < 100ms 75 VDC 0.003 5 V / µs Turn–on 31 36 VDC Turn–off 29 34 VDC Turn–on / turn–off hysteresis 2 Operating input dV / dt Undervoltage protection VDC Time constant Undervoltage blanking time UV blanking time is enabled after start up 50 100 7 µs 200 µs Overvoltage protection Turn–off 76 79.5 VDC Turn–on 75 78 VDC 4 µs 12.0 VDC 15.9 VDC Time constant DC output voltage band No load, over VIN range Output OVP set point Module will shut down 15.2 Input to output and input to baseplate; 1min 2250 Output to baseplate 707 Dielctric withstand Insulation resistance IBC Module Page 4 of 18 7.2 Input to output Rev 1.2 09/2016 9.6 VDC 30 vicorpower.com 800 927.9474 MΩ IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit 20 25 30 ms Common Input Specifications Turn ON delay Start-up inhibit VIN reaching turn-on voltage to enable function operational, see Figure 7 Turn-on delay Enable to 10% VOUT; pre-applied VIN, 0 load capacitance, see Figure 8 75 µs Output voltage rise time From 10% to 90% VOUT, 10% load, 0 load capacitance 50 µs Restart turn-on delay See page 14 for restart after EN pin disable 250 ms 2.5 3.5 W 0.12 No load power dissipation Enabled 0.15 W Input current Disabled Low line, full load 14.1 A Inrush current overshoot Using test circuit in Figure 22, 15% load, high line 10.5 A Input reflected ripple current At max power; Using test circuit in Figure 23; see Figure 6 750 mArms Peak short circuit input current 40 A Repetitive short circuit peak current 25 A Internal input capacitance 17.6 µF Internal input inductance 5 nH Recommended external input capacitance IBC Module Page 5 of 18 200nH maximum source inductance Rev 1.2 09/2016 vicorpower.com 800 927.9474 47 470 µF IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit 750 W Common Output Specifications Output power * 0 Output current P ≤ 750W 70 A Output start up load of IOUT max, maximum output capacitance 15 % Effective output resistance 3.1 Line regulation (K factor) VOUT = K • VIN @ no load 0.198 Current share accuracy Full power operation; See Parallel Operation on page 15; up to 3 units 0.200 mΩ 0.2020 10 % Efficiency 50% load See Figures 1–3 97.8 98.1 % Full load See Figures 1–3 96.9 97.3 % 1.6 nH Internal output inductance Internal output capacitance 92.4 Load capacitance 0 µF 4500 µF 150 mVp-p 150 % Overcurrent protection time constant 1.2 ms Short circuit current response time 1.5 µs Output voltage ripple 20MHz bandwidth (Figure 16), using test circuit in Figure 24 Output overload protection threshold Of IOUT max, will not shut down when started into max COUT and 15% load. Auto restart with duty cycle < 10% 60 105 Switching frequency Dynamic response – load VOUT overshoot / undershoot VOUT response time Dynamic response – line VOUT overshoot Pre-bias voltage 1.0 Load change: ±25% of IOUT max, Slew rate (dI/dt) = 1A/µs See Figures 11–14 100 1 Line step of 5V in 1µs, within VIN operating range. (CIN = 500µF, CO = 350µF) (Figure 15 illustrates similar converter response when subjected to a more severe line transient.) Unit will start up into a pre-bias voltage on the output MHz 0 mV µs 1.25 V 12 VDC * Does not exceed IPC-9592 derating guidelines. At 70ºC ambient, full power operation may exceed IPC-9592 guidelines, but does not exceed component ratings, does not activate OTP and does not compromise reliability. IBC Module Page 6 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Attribute Symbol Conditions / Notes Min Typ Max Unit Control & Interface Specifications Enable (negative logic) Referenced to –IN Module enable threshold 0.8 Module enable current VEN = 0.8V VDC 130 Module disable threshold Modeule disable current VEN = 2.4V Disable hysteresis 500 Enable pin open circuit voltage 2.5 EN to –IN resistance Open circuit Enable (positive logic) 200 µA 2.4 VDC 10 µA mV 3.0 35 VDC kΩ Referenced to –IN Module enable threshold 2.0 2.5 Module disable threshold EN source current (operating) VEN = 5V EN voltage (operating) 3.0 VDC 1.45 VDC 2 mA 4.7 5 5.3 VDC Min Typ Max Unit General Characteristics • Conditions: TCASE = 25ºC, 75% rated load and specified input voltage range unless otherwise specified. Attribute Symbol Conditions / Notes MTBF Calculated per Telcordia SR-332, 40°C Service life Calculated at 30°C Overtemperature shut down TJ ; Converter will reset when overtemperature condition is removed 1.0 Mhrs 7 Years 125 130 135 ºC Mechanical Open frame (without baseplate) 1.38 / 39.1 oz / g Baseplate version 2.25 / 63.9 oz / g Length 2.30 / 58.4 in / mm Width 1.45 / 36.8 in / mm Open frame version 0.42 / 10.6 in / mm With baseplate 0.45 / 11.4 in / mm Weight Height above customer board Pin solderability Moisture sensitivity level Storage life for normal solderability MSL Not applicable, for wave soldering only Clearance to customer board From lowest component on IBC Altitude, operating Derate operating temp 1°C per 1000 feet above sea level Relative humidity, operating Non condensing RoHS compliance Compatible with RoHS directive 2002/95/EC Agency approvals Years N/A 0.12 / 3.0 in / mm -500 10000 Feet 10 90 % UL/CSA 60950-1 cURus UL/CSA 60950-1, EN60950-1 cTUVus Low voltage directive (2006/95/EC) IBC Module Page 7 of 18 1 Rev 1.2 09/2016 vicorpower.com 800 927.9474 CE IB0xxQ096T70xx-xx Electrical Specifications (Cont.) Specifications valid at 48VIN, 100% rated load and 25ºC ambient, unless otherwise indicated. Environmental Qualification • IPC-9592A, based on Class II Category 2 the following detail is applicable. Test Description Test Detail Min. Quanity Tested Low temp 3 High temp 3 Rapid thermal cycling 3 6 DOF random vibration test 3 Input voltage test 3 Output load test 3 Combined stresses test 3 5.2.4 THB (Temperature Humidity Bias) (72hr presoak required) 1000hrs – continuous bias 30 5.2.5 HTOB (High Temperature Operating Bias) Power cycle – On 42 minutes Off 1 minute, On 1 minute, Off 1 minute, On 1 minute, Off 1 minute, On 1 minute, Off 1 minute, On 1 minute, Off 10 minutes. Alternating between maximum and minimum operating voltage every hour. 30 5.2.6 TC (Temperature Cycling) 700 cycles, 30 minute dwell at each extreme – 20C minimum ramp rate 30 5.2.7 PTC (Power & Temperature Cycling) Reference IPC-9592A 3 Random Vibration – Operating IEC 60068-2-64 (normal operation vibration) 3 Random Vibration Non-operating (transportation) IEC 60068-2-64 3 Shock Operating – normal operation shock IEC 60068-2-27 3 Free fall – IEC 60068-2-32 3 Drop Test 1 full shipping container (box) 1 5.2.3 HALT (Highly Accelerated Life Testing) 5.2.8 – 5.2.13 Shock and Vibration 5.2.14.1 Corrosion Resistance – Not required 5.2.14 Other Environmental Tests ESD Classification Testing 5.2.14.2 Dust Resistance – Unpotted class II GR-1274-CORE 3 5.2.14.3 SMT Attachment Reliability IPC-9701 – J-STD-002 N/A 5.2.14.4 Through Hole solderability – J-STD-002 5 HBM testing - JESD22-A114 3 138 Total Quantity (estimated) IBC Module Page 8 of 18 N/A Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx 99 99 98 98 97 97 Efficiency (%) Efficiency (%) Application Characteristics: Waveforms 96 95 94 96 95 94 93 93 92 92 0 14 28 42 56 0 70 14 VIN: 38V 48V VIN: 55V 42 56 70 38V 48V 55V Figure 2 — Efficiency vs. output current, 55ºC ambient Figure 1 — Efficiency vs. output current, 25ºC ambient 99 20 98 16 97 Power (W) Efficiency (%) 28 Output Current (A) Output Current (A) 96 95 12 8 94 4 93 92 0 14 28 42 56 70 0 0 14 VIN: 38V 48V 28 42 56 70 Output Current (A) Output Current (A) 55V VIN: 38V 48V 55V Figure 3 — Efficiency vs. output current, 70ºC ambient Figure 4 — Power dissipation vs. output current at VIN, 25ºC ambient Figure 5 — Inrush current at high line 15% load; 5A/div, max load capacitance Figure 6 — Input reflected ripple current at nominal line, full load See Figure 23 for setup IBC Module Page 9 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Application Characteristics: Waveforms (Cont.) Figure 7 — Turn on delay time; VIN turn on delay at nominal line, 15% load Figure 8 — Turn on delay time via enable at nominal line, 15% load, 0 capacitance. Also illustrates VOUT overshoot at turn-on. Figure 9 — Output voltage rise time at nominal line, 10% load, 0 capacitance Figure 10 — Undershoot at turn off at nominal line, 15% load, 0 capacitance Figure 11 — Load transient response; nominal line, load step 75–100% Figure 12 — Load transient response; full load to 75%; nominal line IBC Module Page 10 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Application Characteristics: Waveforms (Cont.) Figure 13 — Load transient response, nominal line Load step 0–25% Figure 14 — Load transient response; nominal line Load step 25–0% Figure 15 — Input transient response; VIN step low line to high line at full load Figure 16 — Output ripple; nominal line, full load Figure 17 — Two modules parallel array test. VOUT and IIN change when one module is disabled. Nominal VIN, IOUT = 70A Figure 18 — Two modules parallel array test. VOUT and IIN change when one module is enabled. Nominal VIN, IOUT = 70A IBC Module Page 11 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx 80 80 70 70 Output Current (A) Output Current (A) Application Characteristics: Waveforms (Cont.) 60 50 40 30 20 10 60 50 40 30 20 10 0 0 25 35 45 55 65 75 85 95 25 35 Ambient Air Temperature (°C) 200LFM 400LFM 45 65 55 85 75 95 Ambient Air Temperature (°C) 200LFM 600LFM Figure 19 — Maximum output current derating vs. ambient air temperature. Transverse airflow. Board and junction temperatures within IPC-9592 derating guidelines 400LFM 600LFM Figure 20 — Maximum output current derating vs. ambient air temperature. Longitudinal airflow. Board and junction temperatures within IPC-9592 derating guidelines 900 800 600 Current Probe 500 +IN + 400 Vsource _ 300 EN 47µF +OUT IBC –IN Load Power (W) 700 –OUT 200 100 *Maximum load capacitance 0 36 40 44 48 52 56 60 Input Voltage (VDC) Figure 22 — Test circuit; inrush current overshoot Figure 21 — Maximum output ower vs. input voltage +IN +OUT 10µF 0.1µF IBC –IN + Vsource _ 470µF Current Probe +IN EN –IN +OUT IBC Load 10µH –OUT E – Load –OUT Cya Cyc Cyb Cyd 20MHz BW Cy a-d = 4700pF Figure 23 — Test circuit; input reflected ripple current IBC Module Page 12 of 18 Rev 1.2 09/2016 Figure 24 — Test circuit; output voltage ripple vicorpower.com 800 927.9474 C* IB0xxQ096T70xx-xx Application Characteristics: Thermal Data Figure 25 — Thermal plot, 200LFM, 25ºC, 48VIN, 670W output power Figure 26 — Thermal plot, 200LFM, 25ºC, 48VIN, 670W output power Figure 27 — Thermal plot, 400LFM, 25ºC, 48VIN, 670W output power Figure 28 — Thermal plot, 400LFM, 25ºC, 48VIN, 670W output power Figure 29 — Thermal plot, 600LFM, 25ºC, 48VIN, 670W output power Figure 30 — Thermal plot, 600LFM, 25ºC, 48VIN, 670W output power IBC Module Page 13 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Pin / Control Functions +IN / –IN — DC Voltage Input Pins The IBC input voltage range should not be exceeded. An internal undervoltage/overvoltage lockout function prevents operation outside of the normal operating input range. The IBC turns on within an input voltage window bounded by the “Input undervoltage turn-on” and “Input overvoltage turn-off” levels, as specified. The IBC may be protected against accidental application of a reverse input voltage by the addition of a rectifier in series with the positive input, or a reverse rectifier in shunt with the positive input located on the load side of the input fuse. The connection of the IBC to its power source should be implemented with minimal distribution inductance. If the interconnect inductance exceeds 100nH, the input should be bypassed with a RC damper to retain low source impedance and stable operation. With an interconnect inductance of 200nH, the RC damper may be 47μF in series with 0.3Ω. A single electrolytic or equivalent low-Q capacitor may be used in place of the series RC bypass. EN — Enable/Disable 5 1 2 Top View 3 4 Pin Number Function 1 VIN+ 2 Enable 3 VIN- Negative logic option If the EN port is left floating, the IBC output is disabled. Once this port is pulled lower than 0.8VDC with respect to –IN, the output is enabled. The EN port can be driven by a relay, optocoupler, or open collector transistor. Refer to Figures 7 and 8 for the typical enable / disable characteristics. This port should not be toggled at a rate higher than 1Hz. The EN port should also not be driven by or pulled up to an external voltage source. 4 VOUT- 5 VOUT+ Positive logic option If the EN port is left floating, the IBC output is enabled. Once this port is pulled lower than 1.4VDC with respect to –IN, the output is disabled. This action can be realized by employing a relay, optocoupler, or open collector transistor. This port should not be toggled at a rate higher than 1Hz. Figure 31 — IBC Pin Designations The EN port should also not be driven by or pulled up to an external voltage source. The EN port can source up to 2mA at 5VDC. The EN port should never be used to sink current. If the IBC is disabled using the EN pin, the module will attempt to restart approximately every 250ms. Once the module has been disabled for at least 250ms, the turn on delay after the EN pin is enabled will be as shown in Figure 8. +OUT / –OUT — DC Voltage Output Pins Total load capacitance at the output of the IBC should not exceed the specified maximum. Owing to the wide bandwidth and low output impedance of the IBC, low frequency bypass capacitance and significant energy storage may be more densely and efficiently provided by adding capacitance at the input of the IBC. IBC Module Page 14 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Applications Note Input Impedance Recommendations Parallel Operation To take full advantage of the IBC capabilities, the impedance presented to its input terminals must be low from DC to approximately 5MHz. The source should exhibit low inductance and should have a critically damped response. If the interconnect inductance is excessive, the IBC input pins should be bypassed with an RC damper (e.g., 47μF in series with 0.3Ω) to retain low source impedance and proper operation. Given the wide bandwidth of the IBC, the source response is generally the limiting factor in the overall system response. The IBC will inherently current share when operated in an array. Arrays may be used for higher power or redundancy in an application. Current sharing accuracy is maximized when the source and load impedance presented to each IBC within an array are equal. The recommended method to achieve matched impedances is to dedicate common copper planes within the PCB to deliver and return the current to the array, rather than rely upon traces of varying lengths. In typical applications the current being delivered to the load is larger than that sourced from the input, allowing narrower traces to be utilized on the input side if necessary. The use of dedicated power planes is, however, preferable. One or more IBCs in an array may be disabled without adversely affecting operation or reliability as long as the load does not exceed the rated power of the enabled IBCs. The IBC power train and control architecture allow bi-directional power transfer, including reverse power processing from the IBC output to its input. The IBC’s ability to process power in reverse improves the IBC transient response to an output load dump. Thermal Considerations The temperature distribution of the VI Brick® can vary significantly with its input / output operating conditions, thermal management and environmental conditions. Although the PCB is UL rated to 130°C, it is recommended that PCB temperatures be maintained at or below 125°C. For maximum long term reliability, lower PCB temperatures are recommended for continuous operation, however, short periods of operation at 125°C will not negatively impact performance or reliability. Anomalies in the response of the source will appear at the output of the IBC multiplied by its K factor. The DC resistance of the source should be kept as low as possible to minimize voltage deviations. This is especially important if the IBC is operated near low or high line as the overvoltage/undervoltage detection circuitry could be activated. Input Fuse Recommendations The IBC is not internally fused in order to provide flexibility in configuring power systems. However, input line fusing of VI Bricks must always be incorporated within the power system. A fast acting fuse should be placed in series with the +IN port. See safety agency approvals. Application Notes For IBC and VI Brick application notes on soldering, thermal management, board layout, and system design visit www.vicorpower.com. WARNING: Thermal and voltage hazards. The IBC can operate with surface temperatures and operating voltages that may be hazardous to personnel. Ensure that adequate protection is in place to avoid inadvertent contact. IBC Module Page 15 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Mechanical Drawings 2.300±.010 58.42±.25 .15 3.8 inch (mm) .43 10.8 1.450±.010 36.83±.25 .417±.025 10.58±.64 .419±.025 10.64±.64 SEE CHART TYP .11 2.9 .125 3.18 (2) PL. .093 2.36 (3) PL. .040 1.02 (3) PL. 127(6 .060 1.52 (2) PL. DESIGNATOR LENGTH 1 .145 [3.68] 2 .210 [5.33] 3 .180 [4.57] 5R+6&203/,$173(5&67/$7(675(9,6,21 Figure 32 — IBC outline drawing inch (mm) 2.300 58.42 .150 3.81 h .210 5.33 .725 18.42 1.030 26.16 <> 1.450 36.83 .063 THRU 1.59 M3 x .50 TAP THRU (4) PL. h 1.860 47.24 <> .220 5.59 .450±.025 11.43±.64 .180 4.57 .040 1.02 (3) PL. .02 .6 .093 2.36 (3) PL. .125 3.18 (2) PL. .060 1.52 (2) PL. Figure 33 — IBC outline drawing – baseplate option IBC Module Page 16 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 View of underneath panel IB0xxQ096T70xx-xx Mechanical Drawings (Cont.) inch (mm) Top View Figure 34 — IBC PCB recommended hole pattern IBC Module Page 17 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474 IB0xxQ096T70xx-xx Vicor’s comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor’s product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Vicor’s Standard Terms and Conditions All sales are subject to Vicor’s Standard Terms and Conditions of Sale, which are available on Vicor’s webpage or upon request. Product Warranty In Vicor’s standard terms and conditions of sale, Vicor warrants that its products are free from non-conformity to its Standard Specifications (the “Express Limited Warranty”). This warranty is extended only to the original Buyer for the period expiring two (2) years after the date of shipment and is not transferable. UNLESS OTHERWISE EXPRESSLY STATED IN A WRITTEN SALES AGREEMENT SIGNED BY A DULY AUTHORIZED VICOR SIGNATORY, VICOR DISCLAIMS ALL REPRESENTATIONS, LIABILITIES, AND WARRANTIES OF ANY KIND (WHETHER ARISING BY IMPLICATION OR BY OPERATION OF LAW) WITH RESPECT TO THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT, OR ANY OTHER MATTER. This warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, or storage. Vicor shall not be liable for collateral or consequential damage. Vicor disclaims any and all liability arising out of the application or use of any product or circuit and assumes no liability for applications assistance or buyer product design. Buyers are responsible for their products and applications using Vicor products and components. Prior to using or distributing any products that include Vicor components, buyers should provide adequate design, testing and operating safeguards. Vicor will repair or replace defective products in accordance with its own best judgment. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty. Life Support Policy VICOR’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor’s Intellectual Property Department. The products described on this data sheet are protected by the following U.S. Patents Numbers: 5,945,130; 6,403,009; 6,710,257; 6,911,848; 6,930,893; 6,934,166; 6,940,013; 6,969,909; 7,038,917; 7,145,786; 7,166,898; 7,187,263; 7,361,844; D496,906; D505,114; D506,438; D509,472; and for use under 6,975,098 and 6,984,965. Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 email Customer Service: [email protected] Technical Support: [email protected] IBC Module Page 18 of 18 Rev 1.2 09/2016 vicorpower.com 800 927.9474