PRELIMINARY DATA SHEET 2GB Unbuffered DDR3 SDRAM DIMM EBJ21UE8BDF0 (256M words × 64 bits, 2 Ranks) Specifications Features • Density: 2GB • Organization 256M words × 64 bits, 2 ranks • Mounting 16 pieces of 1G bits DDR3 SDRAM sealed in FBGA • Package: 240-pin socket type dual in line memory module (DIMM) PCB height: 30.0mm Lead pitch: 1.0mm Lead-free (RoHS compliant) and Halogen-free • Power supply: VDD = 1.5V ± 0.075V • Data rate: 1600Mbps/1333Mbps/1066Mbps (max.) • Eight internal banks for concurrent operation (components) • Interface: SSTL_15 • Burst lengths (BL): 8 and 4 with Burst Chop (BC) • /CAS Latency (CL): 6, 7, 8, 9, 10, 11 • /CAS write latency (CWL): 5, 6, 7, 8 • Precharge: auto precharge option for each burst access • Refresh: auto-refresh, self-refresh • Refresh cycles Average refresh period 7.8µs at 0°C ≤ TC ≤ +85°C 3.9µs at +85°C < TC ≤ +95°C • Operating case temperature range TC = 0°C to +95°C • Double-data-rate architecture; two data transfers per clock cycle • The high-speed data transfer is realized by the 8 bits prefetch pipelined architecture • Bi-directional differential data strobe (DQS and /DQS) is transmitted/received with data for capturing data at the receiver • DQS is edge-aligned with data for READs; centeraligned with data for WRITEs • Differential clock inputs (CK and /CK) • DLL aligns DQ and DQS transitions with CK transitions • Commands entered on each positive CK edge; data and data mask referenced to both edges of DQS • Data mask (DM) for write data • Posted /CAS by programmable additive latency for better command and data bus efficiency • On-Die-Termination (ODT) for better signal quality Synchronous ODT Dynamic ODT Asynchronous ODT • Multi Purpose Register (MPR) for temperature read out • ZQ calibration for DQ drive and ODT • Programmable Partial Array Self-Refresh (PASR) • /RESET pin for Power-up sequence and reset function • SRT range: Normal/extended • Programmable Output driver impedance control Document No. E1515E10 (Ver. 1.0) Date Published June 2009 (K) Japan Printed in Japan URL: http://www.elpida.com Elpida Memory, Inc. 2008-2009 EBJ21UE8BDF0 Ordering Information Part number Data rate Mbps (max.) Component JEDEC speed bin (CL-tRCD-tRP) EBJ21UE8BDF0-GN-F 1600 DDR3-1600K (11-11-11) EBJ21UE8BDF0-DJ-F 1333 DDR3-1333H (9-9-9) EBJ21UE8BDF0-AE-F 1066 DDR3-1066F (7-7-7) Package Preliminary Data Sheet E1515E10 (Ver. 1.0) 2 240-pin DIMM (lead-free and halogen-free) Contact pad Gold Mounted devices EDJ1108BDSE-GL-F EDJ1108BDSE-GN-F EDJ1108BDSE-GL-F EDJ1108BDSE-GN-F EDJ1108BDSE-DJ-F EDJ1108BDSE-GL-F EDJ1108BDSE-GN-F EDJ1108BDSE-DJ-F EDJ1108BDSE-AE-F EBJ21UE8BDF0 Pin Configurations Front side 1 pin 121 pin 48 pin 49 pin 120 pin 168 pin 169 pin 240 pin Back side Pin No. Pin name Pin No. Pin name Pin No. Pin name Pin No. Pin name 1 VREFDQ 61 A2 121 VSS 181 A1 2 VSS 62 VDD 122 DQ4 182 VDD 3 DQ0 63 CK1 123 DQ5 183 VDD 4 DQ1 64 /CK1 124 VSS 184 CK0 5 VSS 65 VDD 125 DM0 185 /CK0 6 /DQS0 66 VDD 126 NC 186 VDD 7 DQS0 67 VREFCA 127 VSS 187 NC 8 VSS 68 NC 128 DQ6 188 A0 9 DQ2 69 VDD 129 DQ7 189 VDD 10 DQ3 70 A10(AP) 130 VSS 190 BA1 11 VSS 71 BA0 131 DQ12 191 VDD 12 DQ8 72 VDD 132 DQ13 192 /RAS 13 DQ9 73 /WE 133 VSS 193 /CS0 14 VSS 74 /CAS 134 DM1 194 VDD 15 /DQS1 75 VDD 135 NC 195 ODT0 16 DQS1 76 /CS1 136 VSS 196 A13 17 VSS 77 ODT1 137 DQ14 197 VDD 18 DQ10 78 VDD 138 DQ15 198 NC 19 DQ11 79 NC 139 VSS 199 VSS 20 VSS 80 VSS 140 DQ20 200 DQ36 21 DQ16 81 DQ32 141 DQ21 201 DQ37 22 DQ17 82 DQ33 142 VSS 202 VSS 23 VSS 83 VSS 143 DM2 203 DM4 24 /DQS2 84 /DQS4 144 NC 204 NC 25 DQS2 85 DQS4 145 VSS 205 VSS 26 VSS 86 VSS 146 DQ22 206 DQ38 27 DQ18 87 DQ34 147 DQ23 207 DQ39 28 DQ19 88 DQ35 148 VSS 208 VSS 29 VSS 89 VSS 149 DQ28 209 DQ44 30 DQ24 90 DQ40 150 DQ29 210 DQ45 31 DQ25 91 DQ41 151 VSS 211 VSS 32 VSS 92 VSS 152 DM3 212 DM5 33 /DQS3 93 /DQS5 153 NC 213 NC 34 DQS3 94 DQS5 154 VSS 214 VSS 35 VSS 95 VSS 155 DQ30 215 DQ46 36 DQ26 96 DQ42 156 DQ31 216 DQ47 Preliminary Data Sheet E1515E10 (Ver. 1.0) 3 EBJ21UE8BDF0 Pin No. Pin name Pin No. Pin name Pin No. Pin name Pin No. Pin name 37 DQ27 97 DQ43 157 VSS 217 VSS 38 VSS 98 VSS 158 NC 218 DQ52 39 NC 99 DQ48 159 NC 219 DQ53 40 NC 100 DQ49 160 VSS 220 VSS 41 VSS 101 VSS 161 NC 221 DM6 42 NC 102 /DQS6 162 NC 222 NC 43 NC 103 DQS6 163 VSS 223 VSS 44 VSS 104 VSS 164 NC 224 DQ54 45 NC 105 DQ50 165 NC 225 DQ55 46 NC 106 DQ51 166 VSS 226 VSS 47 VSS 107 VSS 167 NC 227 DQ60 48 NC 108 DQ56 168 /RESET 228 DQ61 49 NC 109 DQ57 169 CKE1 229 VSS 50 CKE0 110 VSS 170 VDD 230 DM7 51 VDD 111 /DQS7 171 NC 231 NC 52 BA2 112 DQS7 172 NC 232 VSS 53 NC 113 VSS 173 VDD 233 DQ62 54 VDD 114 DQ58 174 A12 234 DQ63 55 A11 115 DQ59 175 A9 235 VSS 56 A7 116 VSS 176 VDD 236 VDDSPD 57 VDD 117 SA0 177 A8 237 SA1 58 A5 118 SCL 178 A6 238 SDA 59 A4 119 SA2 179 VDD 239 VSS 60 VDD 120 VTT 180 A3 240 VTT Preliminary Data Sheet E1515E10 (Ver. 1.0) 4 EBJ21UE8BDF0 Pin Description Pin name Function A0 to A13 Address input Row address Column address A10 (AP) Auto precharge A0 to A13 A0 to A9 A12 (/BC) Burst chop BA0, BA1, BA2 Bank select address DQ0 to DQ63 Data input/output /RAS Row address strobe command /CAS Column address strobe command /WE Write enable /CS0, /CS1 Chip select CKE0, CKE1 Clock enable CK0, CK1 Clock input /CK0, /CK1 Differential clock input DQS0 to DQS7, /DQS0 to /DQS7 Input and output data strobe DM0 to DM7 Input mask SCL Clock input for serial PD SDA Data input/output for serial PD SA0, SA1, SA2 Serial address input VDD Power for internal circuit VDDSPD Power for serial EEPROM VREFCA Reference voltage for CA VREFDQ Reference voltage for DQ VSS Ground VTT I/O termination supply for SDRAM /RESET Set DRAM to known state ODT0, ODT1 ODT control NC No connection Preliminary Data Sheet E1515E10 (Ver. 1.0) 5 EBJ21UE8BDF0 Serial PD Matrix Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments 1 0 0 1 0 0 1 1 93H 256/256/0-116 -DJ, -AE 1 0 0 1 0 0 1 0 92H 176/256/0-116 SPD revision 0 0 0 1 0 0 0 0 10H Revision 1.0 2 Key byte/DRAM device type 0 0 0 0 1 0 1 1 0BH DDR3 SDRAM 3 Key byte/module type 0 0 0 0 0 0 1 0 02H Unbuffered 4 SDRAM density and banks 0 0 0 0 0 0 1 0 02H 1G bits, 8 banks 5 SDRAM addressing 0 0 0 1 0 0 0 1 11H 14 rows, 10 columns 6 Module nominal voltage, VDD 0 0 0 0 0 0 0 0 00H 1.5V 7 Module organization 0 0 0 0 1 0 0 1 09H 2 ranks/×8 bits 8 Module memory bus width 0 0 0 0 0 0 1 1 03H 64 bits/non-ECC 9 Fine timebase (FTB) dividend/divisor 0 1 0 1 0 0 1 0 52H 5/2 10 Medium timebase (MTB) dividend 0 0 0 0 0 0 0 1 01H 1 11 Medium timebase (MTB) divisor 0 0 0 0 1 0 0 0 08H 8 12 SDRAM minimum cycle time (tCK (min.)) -GN 0 0 0 0 1 0 1 0 0AH 1.25ns 0 0 0 0 1 1 0 0 0CH 1.5ns Byte No. Function described 0 1 Number of serial PD bytes written/SPD device size/CRC coverage -GN -DJ 0 0 0 0 1 1 1 1 0FH 1.875ns 13 Reserved -AE 0 0 0 0 0 0 0 0 00H — 14 SDRAM /CAS latencies supported, LSB -GN 1 0 1 1 1 1 0 0 BCH CL = 6, 7, 8, 9, 11 -DJ 0 0 1 1 1 1 0 0 3CH CL = 6, 7, 8, 9 -AE 0 0 0 1 1 1 0 0 1CH CL = 6, 7, 8 15 SDRAM /CAS latencies supported, MSB 0 0 0 0 0 0 0 0 00H — 16 SDRAM minimum /CAS latencies time (tAA (min.)) 0 1 1 0 1 0 0 1 69H 13.125ns SDRAM write recovery time (tWR (min)) 0 1 1 1 1 0 0 0 78H 15ns 1 1 0 1 0 0 1 69H 13.125ns 0 1 1 0 0 0 0 30H 6ns 17 18 19 SDRAM minimum /RAS to /CAS delay 0 (tRCD) SDRAM minimum row active to row active delay (tRRD) 0 -GN, -DJ 0 0 1 1 1 1 0 0 3CH 7.5ns SDRAM minimum row precharge time (tRP) -AE 0 1 1 0 1 0 0 1 69H 13.125ns 21 SDRAM upper nibbles for tRAS and tRC 0 0 0 1 0 0 0 1 11H 22 SDRAM minimum active to precharge time (tRAS), LSB 0 -GN 0 0 1 1 0 0 0 18H 35ns 20 -DJ 0 0 1 0 0 0 0 0 20H 36ns -AE 0 0 1 0 1 1 0 0 2CH 37.5ns Preliminary Data Sheet E1515E10 (Ver. 1.0) 6 EBJ21UE8BDF0 Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments 1 0 0 0 0 0 0 1 81H 48.125ns -DJ 1 0 0 0 1 0 0 1 89H 49.125ns -AE 1 0 0 1 0 1 0 1 95H 50.625ns 0 1 1 1 0 0 0 0 70H 110ns 0 0 0 0 0 0 1 1 03H 110ns 0 0 1 1 1 1 0 0 3CH 7.5ns 0 0 1 1 1 1 0 0 3CH 7.5ns 0 0 0 0 0 0 0 0 00H 30.0ns 0 0 0 0 0 0 0 1 01H 37.5ns 1 1 1 1 0 0 0 0 F0H 30.0ns Byte No. Function described 23 24 25 26 27 28 SDRAM minimum active to active /autorefresh time (tRC), LSB -GN SDRAM minimum refresh recovery time delay (tRFC), LSB SDRAM minimum refresh recovery time delay (tRFC), MSB SDRAM minimum internal write to read command delay (tWTR) SDRAM minimum internal read to precharge command delay (tRTP) Upper nibble for tFAW -GN, -DJ -AE 29 Minimum four activate window delay time (tFAW) -GN, -DJ 0 0 1 0 1 1 0 0 2CH 37.5ns 30 SDRAM output drivers supported 1 0 0 0 0 0 1 1 83H DLL-off/RZQ/6, 7 31 SDRAM refresh options 1 0 0 0 0 0 0 1 81H PASR/2X refresh rate at +85°C to +95°C 32 Module thermal sensor 0 0 0 0 0 0 0 0 00H Not incorporated 33 SDRAM device type 0 0 0 0 0 0 0 0 00H Standard -AE 34 to 59 Reserved 0 0 0 0 0 0 0 0 00H — 60 Module nominal height 0 0 0 0 1 1 1 1 0FH 29 < height ≤ 30mm 61 Module maximum thickness 0 0 0 1 0 0 0 1 11H 62 Reference raw card used 0 0 0 0 0 0 0 1 01H Raw Card B 63 Address mapping from edge connecter to 0 DRAM 0 0 0 0 0 0 1 01H Mirrored 64 to 116 Module specific section 0 0 0 0 0 0 0 0 00H — 0 0 0 0 0 0 1 0 02H Elpida Memory 1 1 1 1 1 1 1 0 FEH Elpida Memory 117 118 Module ID: manufacturer’s JEDEC ID code, LSB Module ID: manufacturer’s JEDEC ID code, MSB 119 Module ID: manufacturing location × × × × × × × × ×× 120 Module ID: manufacturing date × × × × × × × × ×× Year code (BCD) 121 Module ID: manufacturing date × × × × × × × × ×× Week code (BCD) 122 to 125 Module ID: module serial number × × × × × × × × ×× 126 Cyclical redundancy code (CRC) -GN 0 0 0 0 0 0 1 1 03H -DJ 1 0 1 0 1 0 1 1 ABH -AE 1 1 1 0 1 0 0 1 E9H Preliminary Data Sheet E1515E10 (Ver. 1.0) 7 EBJ21UE8BDF0 Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value 0 0 0 1 0 1 0 0 14H -DJ 1 0 1 0 0 1 1 1 A7H -AE 0 0 0 0 1 1 1 0 0EH Byte No. Function described 127 Cyclical redundancy code (CRC) -GN Comments 128 Module part number 0 1 0 0 0 1 0 1 45H E 129 Module part number 0 1 0 0 0 0 1 0 42H B 130 Module part number 0 1 0 0 1 0 1 0 4AH J 131 Module part number 0 0 1 1 0 0 1 0 32H 2 132 Module part number 0 0 1 1 0 0 0 1 31H 1 133 Module part number 0 1 0 1 0 1 0 1 55H U 134 Module part number 0 1 0 0 0 1 0 1 45H E 135 Module part number 0 0 1 1 1 0 0 0 38H 8 136 Module part number 0 1 0 0 0 0 1 0 42H B 137 Module part number 0 1 0 0 0 1 0 0 44H D 138 Module part number 0 1 0 0 0 1 1 0 46H F 139 Module part number 0 0 1 1 0 0 0 0 30H 0 140 Module part number 0 0 1 0 1 1 0 1 2DH — 141 Module part number -GN 0 1 0 0 0 1 1 1 47H G -DJ 0 1 0 0 0 1 0 0 44H D -AE 0 1 0 0 0 0 0 1 41H A 0 1 0 0 1 1 1 0 4EH N -DJ 0 1 0 0 1 0 1 0 4AH J -AE 0 1 0 0 0 1 0 1 45H E 142 Module part number -GN 143 Module part number 0 0 1 0 1 1 0 1 2DH — 144 Module part number 0 1 0 0 0 1 1 0 46H F 145 Module part number 0 0 1 0 0 0 0 0 20H (Space) 146 Module revision code 0 0 1 1 0 0 0 0 30H Initial 147 Module revision code 0 0 1 0 0 0 0 0 20H (Space) 0 0 0 0 0 0 1 0 02H Elpida Memory 1 1 1 1 1 1 1 0 FEH Elpida Memory 148 149 150 to 175 176 to 254 SDRAM manufacturer’s JEDEC ID code, LSB SDRAM manufacturer’s JEDEC ID code, MSB Manufacturer's specific data Intel extreme memory profile -GN -DJ, -AE 255 Refer to SPD for Intel Extreme Memory Profile Section 0 0 0 Open for customer use Preliminary Data Sheet E1515E10 (Ver. 1.0) 8 0 0 0 0 0 00H Not supported EBJ21UE8BDF0 SPD for Intel Extreme Memory Profile (EBJ21UE8BDF0-GN) Byte No. Function described Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value 176 Intel extreme memory profile ID string 0 0 0 0 1 1 0 0 0CH 177 Intel extreme memory profile ID string 0 1 0 0 1 0 1 0 4AH 178 Intel extreme memory profile organization type 0 0 0 0 0 0 1 1 03H 179 Intel extreme memory profile revision 0 0 0 1 0 0 0 1 11H Revision 1.1 0 0 0 0 0 0 0 1 01H 1 0 0 0 0 1 0 0 0 08H 8 0 0 0 0 0 0 0 1 01H 1 0 0 0 0 1 0 0 0 08H 8 0 0 0 0 0 0 0 0 00H 180 181 182 183 184 Medium timebase (MTB) dividend for profile 1 Medium timebase (MTB) divisor for profile 1 Medium timebase (MTB) dividend for profile 2 Medium timebase (MTB) divisor for profile 2 Reserved for global byte Comments Intel Extreme Memory Profile ID String Intel Extreme Memory Profile ID String Profile 1: Enabled / Profile 2: Enabled / Profile 1: 1 DIMM per CH / Profile 2: 1 DIMM per CH / [For Profile 1] Byte No. Function described Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments 185 0 0 1 0 1 0 1 0 2AH 1.50V 0 0 0 0 1 0 1 0 0AH DDR3-1600 0 1 1 0 1 0 0 1 69H 13.125ns 1 0 1 1 1 1 0 0 BCH 6, 7, 8, 9, 11 0 0 0 0 0 0 0 0 00H 0 1 1 0 1 0 0 1 69H 13.125ns 0 1 1 0 1 0 0 1 69H 13.125ns 0 1 1 0 1 0 0 1 69H 13.125ns 15ns 186 187 188 189 190 191 192 Module VDD voltage level SDRAM minimum cycle time (tCK (min.)) SDRAM minimum /CAS latencies time (tAA (min.)) SDRAM /CAS latencies supported, LSB (CL MASK) SDRAM /CAS latencies supported, MSB (CL MASK) Minimum CAS write latency time (tCWL(min)) SDRAM minimum row precharge time (tRP) SDRAM minimum /RAS to /CAS delay (tRCD) 193 SDRAM write recovery time (tWR (min)) 0 1 1 1 1 0 0 0 78H 194 SDRAM upper nibbles for tRAS and tRC 0 0 0 1 0 0 0 1 11H 0 0 0 1 1 0 0 0 18H 35ns 1 0 0 0 0 1 1 0 86H 48.75ns 0 0 1 1 1 1 1 1 3FH 7.8µs 0 0 0 0 0 0 0 0 00H 7.8µs 0 1 1 1 0 0 0 0 70H 110ns 0 0 0 0 0 0 1 1 03H 110ns 0 0 1 1 1 1 0 0 3CH 7.5ns 195 196 197 198 199 200 201 SDRAM minimum active to precharge time (tRAS), LSB SDRAM minimum active to active /autorefresh time (tRC), LSB Maximum average periodic refresh interval (tREFI), LSB Maximum average periodic refresh interval (tREFI), MSB SDRAM minimum refresh recovery time delay (tRFC), LSB SDRAM minimum refresh recovery time delay (tRFC), MSB SDRAM minimum internal read to precharge command delay (tRTP) Preliminary Data Sheet E1515E10 (Ver. 1.0) 9 EBJ21UE8BDF0 Byte No. Function described 202 203 204 205 206 207 208 209 Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments SDRAM minimum row active to row active 0 delay (tRRD) 0 1 1 0 0 0 0 30H 6ns Upper nibble for tFAW 0 0 0 0 0 0 0 0 00H 30.0ns 1 1 1 1 0 0 0 0 F0H 30.0ns 0 0 1 1 1 1 0 0 3CH 7.5ns 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H Minimum four activate window delay time (tFAW) SDRAM minimum internal write to read command delay (tWTR) Write to read & read to write command turn-around time pull-in Back to back command turn-around time pull-in System address/ command rate (1N or 2N mode) Auto self-refresh performance (sub 1x refresh and IDD6 impacts) Default - No adjustment Default - No adjustment System operates in default mode TBD 210 to 218 Reserved 0 0 0 0 0 0 0 0 00H 219 Vendor personality byte 0 0 0 0 0 0 0 0 00H Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments 220 Module VDD voltage level (extreme settings) 0 0 1 0 1 1 0 0 2CH 1.60V 221 SDRAM minimum cycle time (tCK (min)) 0 0 0 0 1 0 1 0 0AH DDR3-1600 Minimum CAS latency time (tAA (min)) 0 1 1 0 1 0 0 1 69H 13.125ns 1 0 1 1 1 1 0 0 BCH 6, 7, 8, 9, 11 0 0 0 0 0 0 0 0 00H 0 1 1 0 1 0 0 1 69H 13.125ns 0 1 1 0 1 0 0 1 69H 13.125ns 0 1 1 0 1 0 0 1 69H 13.125ns 15ns [For Profile 2] Byte No. Function described 222 223 224 225 226 227 SDRAM /CAS latencies supported, LSB (CL MASK) SDRAM /CAS latencies supported, MSB (CL MASK) Minimum CAS write latency time (tCWL (min)) SDRAM minimum row precharge time (tRP) SDRAM minimum /RAS to /CAS delay (tRCD) 228 SDRAM write recovery time (tWR (min)) 0 1 1 1 1 0 0 0 78H 229 SDRAM upper nibbles for tRAS and tRC 0 0 0 1 0 0 0 1 11H 0 0 0 1 1 0 0 0 18H 35ns 1 0 0 0 0 1 1 0 86H 48.75ns 0 0 1 1 1 1 1 1 3FH 7.8us 0 0 0 0 0 0 0 0 00H 7.8us 0 1 1 1 0 0 0 0 70H 110ns 0 0 0 0 0 0 1 1 03H 110ns 0 0 1 1 1 1 0 0 3CH 7.5ns 0 0 1 1 0 0 0 0 30H 6ns 230 231 232 233 234 235 236 237 SDRAM minimum active to precharge time (tRAS), LSB SDRAM minimum active to active /autorefresh time (tRC), LSB Maximum average periodic refresh interval (tREFI), LSB Maximum average periodic refresh interval (tREFI), MSB SDRAM minimum refresh recovery time delay (tRFC), LSB SDRAM minimum refresh recovery time delay (tRFC), MSB SDRAM minimum internal read to precharge command delay (tRTP) SDRAM minimum row active to row active delay (tRRD) Preliminary Data Sheet E1515E10 (Ver. 1.0) 10 EBJ21UE8BDF0 Byte No. Function described Bit7 Bit6 Bit5 Hex Bit4 Bit3 Bit2 Bit1 Bit0 value Comments 238 0 0 0 0 0 0 0 0 00H 30.0ns 1 1 1 1 0 0 0 0 F0H 30.0ns 0 0 1 1 1 1 0 0 3CH 7.5ns 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H 0 0 0 0 0 0 0 0 00H 239 240 241 242 243 244 Upper nibble for tFAW Minimum four activate window delay time (tFAW) SDRAM minimum internal write to read command delay (tWTR) Write to read & read to write command turn-around time pull-in Back to back command turn-around time pull-in System address/ command rate (1N or 2N mode) Auto self-refresh performance (sub 1x refresh and IDD6 impacts) 245 to 253 Reserved 0 0 0 0 0 0 0 0 00H 254 Vendor personality byte 0 0 0 0 0 0 0 0 00H Preliminary Data Sheet E1515E10 (Ver. 1.0) 11 Default - No adjustment Default - No adjustment System operates in default mode TBD EBJ21UE8BDF0 Block Diagram Rs3 Rs3 Rs2 Rs2 Rs2 Rs2 Rs2 Rs3 Rs3 Rs2 Rs2 Rs2 Rs2 Rs2 Rs4 /CK CK Rs4 /CK CK /CS ODT CKE Address BA Command /CK ZQ CK DQ0 to DQ7 /CS ODT CKE Address BA Command DM Rs4 /CK ZQ Rs4 D15 /DQS CK DQ0 to DQ77 /RESET SCL SA0 SCL SA1 SA2 A1 A2 A0 SDA U0 WP V3 D10 D11 V4 D12 V5 D13 V6 D14 V7 D15 V8 D16 V1 V1 V3 V2 D0 D1 V4 D2 V5 D3 V6 D4 V7 D5 V8 D6 D7 Address and Control lines Preliminary Data Sheet E1515E10 (Ver. 1.0) 12 VTT * D0 to D15: 1G bits DDR3 SDRAM Address, BA: A0 to A13, BA0 to BA2 Command: /RAS, /CAS, /WE U0: 256 bytes EEPROM Rs1: 15Ω Rs2: 39Ω Rs3: 36Ω Rs4: 240Ω VTT V2 SDA Rs4 CK /CK Rs4 /CK ZQ CK /CS ODT CKE Address BA Command DQ0 to DQ7 SDRAMs (D0 to D15), SPD Notes : 1. DQ wiring may be changed within a byte. 2. DQ, DQS, /DQS, ODT, DM, CKE, /CS relationships must be maintained as shown. D9 /CS ODT CKE Address BA Command /CK Rs4 DM Rs4 /CK ZQ Serial PD SPD SDRAMs (D0 to D15) SDRAMs (D0 to D15) SDRAMs (D0 to D15) VSS ZQ D13 /DQS CK Rs4 DQ0 to DQ7 /CS ODT CKE Address BA Command DM 8 Rs1 /RESET:SDRAMs (D0 to D15) VTT VDDSPD VREFCA VREFDQ VDD DQ0 to DQ7 DQS D4 /DQS DM4 DQ32 to DQ39 DM DQS Rs1 ZQ ZQ CK /CS ODT CKE Address BA Command /CK DQ0 to DQ7 Rs1 /CK DQ0 to DQ7 DM D14 /DQS Rs1 /DQS4 CK DM ZQ /CS ODT CKE Address BA Command DQ0 to DQ7 Rs4 DM /DQS /CK /DQS D12 DQS D5 /DQS DM5 8 Rs1 DQ40 to DQ47 Rs4 ZQ DQS4 DQS D3 CK DQS Rs1 DM3 8 Rs1 DQ24 to DQ31 DM Rs1 Rs1 Rs1 ZQ DQS DQS Rs1 /DQS5 CK DQ0 to DQ7 /CS ODT CKE Address BA Command DM ZQ Rs4 DQ0 to DQ7 D11 /DQS /CK DM DQS5 DQS D2 CK /DQS DM2 8 Rs1 DQ16 to DQ23 DQ0 to DQ7 Rs1 DQS Rs1 DM D6 /DQS DM6 8 Rs1 DQ48 to DQ55 Rs1 /DQS2 ZQ DQS /CS ODT CKE Address BA Command ZQ D16 /DQS Rs1 Rs1 Rs4 DQ0 to DQ7 /CS ODT CKE Address BA Command Rs4 /CK CK /CS ODT CKE Address BA Command Rs4 DM ZQ DQ0 to DQ7 Rs1 /CK DQ0 to DQ7 Rs1 /DQS3 8 Rs1 /DQS6 CK DM /CS ODT CKE Address BA Command 8 Rs1 Rs4 DM1 DM DM7 DQ56 to DQ63 D10 /DQS /CK /DQS Rs1 DQS3 ZQ DQS D7 /DQS Rs1 DQS6 DQS D1 CK DQS /DQS1 DQS2 DQ0 to DQ7 DQS Rs1 /DQS7 Rs1 Rs1 DQ8 to DQ15 DM ZQ /CK DQ0 to DQ7 CK DM DQS7 D9 /DQS /CS ODT CKE Address BA Command DQS1 8 Rs1 DQS D0 /CS ODT CKE Address BA Command DM0 DQ0 to DQ7 /DQS Rs1 VTT Rs1 DQS Rs1 /CS ODT CKE Address BA Command /DQS0 VDD VDD VTT /CS ODT CKE Address BA Command /CK1 CK1 /CS1 ODT1 CKE1 /CK0 CK0 3 Command 17 Address, BA /CS0 ODT0 CKE0 Rs1 DQS0 EBJ21UE8BDF0 Electrical Specifications • All voltages are referenced to VSS (GND). Absolute Maximum Ratings Parameter Symbol Value Unit Notes Power supply voltage VDD −0.4 to +1.975 V 1, 3, 4 Input voltage VIN −0.4 to +1.975 V 1, 4 Output voltage VOUT −0.4 to +1.975 V 1, 4 Reference voltage VREFCA −0.4 to 0.6 × VDD V 3, 4 Reference voltage for DQ VREFDQ −0.4 to 0.6 × VDDQ V 3, 4 Storage temperature Tstg −55 to +100 °C 1, 2, 4 Power dissipation PD 8 W Short circuit output current IOUT 50 mA 1, 4 Notes: 1. Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Storage temperature is the case surface temperature on the center/top side of the DRAM. 3. VDD and VDDQ must be within 300mV of each other at all times; and VREF must be not greater than 0.6 × VDDQ, When VDD and VDDQ are less than 500mV; VREF may be equal to or less than 300mV. 4. DDR3 SDRAM component specification. Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational section of this specification Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Operating Temperature Condition Parameter Symbol Rating Unit Notes Operating case temperature TC 0 to +95 °C 1, 2, 3 Notes: 1. Operating temperature is the case surface temperature on the center/top side of the DRAM. 2. The Normal Temperature Range specifies the temperatures where all DRAM specifications will be supported. During operation, the DRAM case temperature must be maintained between 0°C to +85°C under all operating conditions. 3. Some applications require operation of the DRAM in the Extended Temperature Range between +85°C and +95°C case temperature. Full specifications are guaranteed in this range, but the following additional conditions apply: a) Refresh commands must be doubled in frequency, therefore reducing the refresh interval tREFI to 3.9µs. (This double refresh requirement may not apply for some devices.) b) If Self-refresh operation is required in the Extended Temperature Range, then it is mandatory to either use the Manual Self-Refresh mode with Extended Temperature Range capability (MR2 bit [A6, A7] = [0, 1]) or enable the optional Auto Self-Refresh mode (MR2 bit [A6, A7] = [1, 0]). Preliminary Data Sheet E1515E10 (Ver. 1.0) 13 EBJ21UE8BDF0 Recommended DC Operating Conditions (TC = 0°C to +85°C) Parameter Symbol min. typ. max. Unit Notes Supply voltage VDD, VDDQ 1.425 1.5 1.575 V 1, 2, 3 VSS 0 0 0 V 1 3.6 VDDSPD 3.0 3.3 Input reference voltage VREFCA (DC) 0.49 × VDDQ 0.50 × VDDQ 0.51 × VDDQ V 1, 4, 5 Input reference voltage for DQ VREFDQ (DC) 0.49 × VDDQ 0.50 × VDDQ 0.51 × VDDQ V 1, 4, 5 Termination voltage VTT VDDQ/2 – TBD TBD V Notes: 1. 2. 3. 4. VDDQ/2 + TBD V DDR3 SDRAM component specification. Under all conditions VDDQ must be less than or equal to VDD. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together. The AC peak noise on VREF may not allow VREF to deviate from VREF(DC) by more than ±1% VDD (for reference: approx ±15 mV). 5. For reference: approx. VDD/2 ±15 mV. Preliminary Data Sheet E1515E10 (Ver. 1.0) 14 EBJ21UE8BDF0 DC Characteristics 1 (TC = 0°C to +85°C, VDD = 1.5V ± 0.075V, VSS = 0V) Parameter Operating current (ACT-PRE) (Another rank is in IDD2P1) Operating current (ACT-PRE) (Another rank is in IDD3N) Operating current (ACT-READ-PRE) (Another rank is in IDD2P1) Operating current (ACT-READ-PRE) (Another rank is in IDD3N) Symbol IDD0 IDD0 IDD1 IDD1 IDD2P1 Precharge power-down standby current IDD2P0 Precharge standby current IDD2N Precharge standby ODT current IDD2NT Precharge quiet standby current IDD2Q Active power-down current (Always fast exit) IDD3P Active standby current IDD3N Operating current (Burst read operating) (Another rank is in IDD2P1) Operating current (Burst read operating) (Another rank is in IDD3N) Operating current (Burst write operating) (Another rank is in IDD2P1) Operating current (Burst write operating) (Another rank is in IDD3N) IDD4R IDD4R IDD4W IDD4W Burst refresh current (Another rank is in IDD2P1) IDD5B Burst refresh current (Another rank is in IDD3N) IDD5B All bank interleave read current (Another rank is in IDD2P1) IDD7 All bank interleave read current (Another rank is in IDD3N) IDD7 Data rate (Mbps) max. 1600 1333 1066 1600 1333 1066 1600 1333 1066 1200 1080 960 1440 1280 1160 1320 1200 1080 1600 1333 1066 1560 1400 1280 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 1600 1333 1066 720 640 560 240 224 208 1040 960 880 1040 960 880 960 880 800 720 640 560 1200 1040 960 2200 1920 1560 2440 2120 1760 2280 2000 1640 2520 2200 1840 2600 2480 2360 2840 2680 2560 3160 2800 2440 3400 3000 2640 Preliminary Data Sheet E1515E10 (Ver. 1.0) 15 Unit Notes mA mA mA mA mA Fast PD Exit mA Slow PD Exit mA mA mA mA mA mA mA mA mA mA mA mA mA EBJ21UE8BDF0 Self-Refresh Current (TC = 0°C to +85°C, VDD = 1.5V ± 0.075V) Parameter Self-refresh current normal temperature range Self-refresh current extended temperature range Auto self-refresh current (optional) Symbol max. Unit IDD6 160 mA IDD6ET 288 mA IDD6TC mA Notes Timings used for IDD and IDDQ Measurement-Loop Patterns Parameter DDR3-1600 DDR3-1333 DDR3-1066 11-11-11 9-9-9 7-7-7 Unit CL 11 9 7 tCK tCK min. 1.25 1.5 1.875 ns nRCD min. 11 9 7 nCK nRC min. 39 33 27 nCK nRAS min. 28 24 20 nCK nRP min. 11 9 7 nCK nFAW 24 20 20 nCK nRRD 5 4 4 nCK nRFC 88 74 59 nCK DC Characteristics 2 (TC = 0°C to +85°C, VDD, VDDQ = 1.5V ± 0.075V) (DDR3 SDRAM Component Specification) Parameter Symbol Value Input leakage current ILI 2 µA VDD ≥ VIN ≥ VSS Output leakage current ILO 5 µA DDQ ≥ VOUT ≥ VSS Preliminary Data Sheet E1515E10 (Ver. 1.0) 16 Unit Notes EBJ21UE8BDF0 Pin Functions CK, /CK (input pin) CK and /CK are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of /CK. Output (read) data is referenced to the crossings of CK and /CK (both directions of crossing). /CS (input pin) All commands are masked when /CS is registered high. /CS provides for external rank selection on systems with multiple ranks. /CS is considered part of the command code. /RAS, /CAS, and /WE (input pins) /RAS, /CAS and /WE (along with /CS) define the command being entered. A0 to A13 (input pins) Provided the row address for active commands and the column address for read/write commands to select one location out of the memory array in the respective bank. (A10(AP) and A12(/BC) have additional functions, see below) The address inputs also provide the op-code during mode register set commands. [Address Pins Table] Address (A0 to A13) Row address (RA) Column address (CA) AX0 to AX13 AY0 to AY9 Notes A10(AP) (input pin) A10 is sampled during read/write commands to determine whether auto-precharge should be performed to the accessed bank after the read/write operation. (high: auto-precharge; low: no auto-precharge) A10 is sampled during a precharge command to determine whether the precharge applies to one bank (A10 = low) or all banks (A10 = high). If only one bank is to be precharged, the bank is selected by bank addresses (BA). A12 (/BC) (input pin) A12 is sampled during read and write commands to determine if burst chop (on-the-fly) will be performed. (A12 = high: no burst chop, A12 = low: burst chopped.) BA0 to BA2 (input pins) BA0, BA1 and BA2 define to which bank an active, read, write or precharge command is being applied. BA0 and BA1 also determine if a mode register is to be accessed during a MRS cycle. [Bank Select Signal Table] BA0 BA1 BA2 Bank 0 L L L Bank 1 H L L Bank 2 L H L Bank 3 H H L Bank 4 L L H Bank 5 H L H Bank 6 L H H Bank 7 H H H Remark: H: VIH. L: VIL. Preliminary Data Sheet E1515E10 (Ver. 1.0) 17 EBJ21UE8BDF0 CKE (input pin) CKE high activates, and CKE low deactivates, internal clock signals and device input buffers and output drivers. Taking CKE low provides precharge power-down and self-refresh operation (all banks idle), or active power-down (row active in any bank). CKE is asynchronous for self-refresh exit. After VREF has become stable during the power-on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh entry and exit, VREF must be maintained to this input. CKE must be maintained high throughout read and write accesses. Input buffers, excluding CK, /CK, ODT and CKE are disabled during power-down. Input buffers, excluding CKE, are disabled during self-refresh. DQ (input and output pins) Bi-directional data bus. DQS and /DQS (input and output pin) Output with read data, input with write data. Edge-aligned with read data, centered in write data. The data strobe DQS is paired with differential signals /DQS to provide differential pair signaling to the system during READs and WRITEs. ODT (input pins) ODT (registered high) enables termination resistance internal to the DDR3 SDRAM. When enabled, ODT is only applied to each DQ, DQS, /DQS, DM. The ODT pin will be ignored if the mode register (MR1) is programmed to disable ODT. DM (input pins) DM is the reference signal of the data input mask function. DMs are sampled at the cross point of DQS and /DQS. VDD (power supply pins) 1.5V is applied. (VDD is for the internal circuit.) VDDSPD (power supply pin) 3.3V is applied (For serial EEPROM). VSS (power supply pin) Ground is connected. VTT (power supply pin) I/O termination supply for SDRAM. VREFDQ (power supply) Reference voltage for DQ. VREFCA (power supply) Reference voltage for CA. /RESET (input pin) /RESET is negative active signal (active low) and is referred to GND. Detailed Operation Part, Electrical Characteristics and Timing Waveforms Refer to the EDJ1104BDSE, EDJ1108BDSE datasheet (E1494E). Preliminary Data Sheet E1515E10 (Ver. 1.0) 18 EBJ21UE8BDF0 Physical Outline Unit: mm Front side 4.00 max 0.5 min (DATUM -A-) 4.00 min Component area (Front) 1 120 B A 47.00 1.27 ± 0.10 71.00 133.35 Component area (Back) 2.80 min C ± ± ± 30.00 240 17.30 121 9.50 Back side ± ± ECA-TS2-0192-03 Preliminary Data Sheet E1515E10 (Ver. 1.0) 19 EBJ21UE8BDF0 CAUTION FOR HANDLING MEMORY MODULES When handling or inserting memory modules, be sure not to touch any components on the modules, such as the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on these components to prevent damaging them. In particular, do not push module cover or drop the modules in order to protect from mechanical defects, which would be electrical defects. When re-packing memory modules, be sure the modules are not touching each other. Modules in contact with other modules may cause excessive mechanical stress, which may damage the modules. MDE0202 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR MOS DEVICES Exposing the MOS devices to a strong electric field can cause destruction of the gate oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it, when once it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. MOS devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. MOS devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor MOS devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES No connection for CMOS devices input pins can be a cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. The unused pins must be handled in accordance with the related specifications. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Power-on does not necessarily define initial status of MOS devices. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the MOS devices with reset function have not yet been initialized. Hence, power-on does not guarantee output pin levels, I/O settings or contents of registers. MOS devices are not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for MOS devices having reset function. CME0107 Preliminary Data Sheet E1515E10 (Ver. 1.0) 20 EBJ21UE8BDF0 The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Elpida Memory, Inc. Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights (including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or third parties by or arising from the use of the products or information listed in this document. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of Elpida Memory, Inc. or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of the customer's equipment shall be done under the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. [Product applications] Be aware that this product is for use in typical electronic equipment for general-purpose applications. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability. However, users are instructed to contact Elpida Memory's sales office before using the product in aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment, medical equipment for life support, or other such application in which especially high quality and reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk of bodily injury. [Product usage] Design your application so that the product is used within the ranges and conditions guaranteed by Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage when the product is used beyond the guaranteed ranges and conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other consequential damage due to the operation of the Elpida Memory, Inc. product. [Usage environment] Usage in environments with special characteristics as listed below was not considered in the design. Accordingly, our company assumes no responsibility for loss of a customer or a third party when used in environments with the special characteristics listed below. Example: 1) Usage in liquids, including water, oils, chemicals and organic solvents. 2) Usage in exposure to direct sunlight or the outdoors, or in dusty places. 3) Usage involving exposure to significant amounts of corrosive gas, including sea air, CL 2 , H 2 S, NH 3 , SO 2 , and NO x . 4) Usage in environments with static electricity, or strong electromagnetic waves or radiation. 5) Usage in places where dew forms. 6) Usage in environments with mechanical vibration, impact, or stress. 7) Usage near heating elements, igniters, or flammable items. If you export the products or technology described in this document that are controlled by the Foreign Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by U.S. export control regulations, or another country's export control laws or regulations, you must follow the necessary procedures in accordance with such laws or regulations. If these products/technology are sold, leased, or transferred to a third party, or a third party is granted license to use these products, that third party must be made aware that they are responsible for compliance with the relevant laws and regulations. M01E0706 Preliminary Data Sheet E1515E10 (Ver. 1.0) 21