MicroPower Direct Compact MiniDIP, 2W High Isolation DC/DC Converters Key Features G200I Series Miniature DIP Package 2W Output Power 3.6 MH MTBF 3.0 kVDC Isolation Single & Dual Outputs Low Cost Electrical Specifications Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 Internal Capacitor Input Voltage Range Input Filter Reverse Polarity Input Current Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 Units 0.3 A Max. !3.0 !1.0 !1.5 Units % % % 150 200 5 mV P - P mV P - P mV rms % %/1C VDC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. !1.0 Dual Output , Balanced Loads !0.1 For Vin Change of 1% !1.2 See Model Selection Guide 100 Over Line, Load & Temp. 120 !0.01 Momentary (0.5 Sec.) !0.02 General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 50 Typ. Max. 80 80 120 100 Units VDC MΩ pF kHz Max. +70 +125 Units 1C 1C 95 % Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. -40 +25 -40 Free Air Convection RH, Non-condensing Physical Case Size, 5V, 12V & 24V Input Models Case Size, 48VDC Input Models Case Material Weight 0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm) 0.80 x 0.40 x 0.30 Inches (20.32 x 10.16 x 7.50 mm) Non-Conductive Black Plastic 0.09 Oz (2.7g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 251C, Gnd Benign Min. Typ. 3.6 Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 55.0 650 Units Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input All Models VDC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: [email protected] WEB: www/micropowerdirect.com Model Selection Guide Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 452 35 3.3 500.0 10.0 11 73 1,000 5 4.5 - 5.5 526 35 5.0 400.0 8.0 11 76 1,000 5 4.5 - 5.5 495 35 12.0 165.0 3.0 7 80 1,000 5 4.5 - 5.5 499 35 15.0 133.0 2.5 7 80 1,000 5 4.5 - 5.5 519 35 10 77 1,000 !5.0 !200.0 !4.0 5 4.5 - 5.5 504 35 7 79 1,000 !12.0 !83.0 !1.5 5 4.5 - 5.5 501 35 7 79 1,000 !15.0 !66.0 !1.0 12 10.8 - 13.2 185 25 3.3 500.0 10.0 8 74 500 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500 12 10.8 - 13.2 200 25 12.0 165.0 3.0 5 82 500 12 10.8 - 13.2 200 25 15.0 133.0 2.5 5 83 500 12 10.8 - 13.2 222 25 8 75 500 !5.0 !200.0 !4.0 12 10.8 - 13.2 201 25 5 82 500 !12.0 !83.0 !1.5 12 10.8 - 13.2 200 25 5 82 500 !15.0 !66.0 !1.0 24 21.6 - 26.4 92 10 3.3 500.0 10.0 8 74 200 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200 24 21.6 - 26.4 101 10 12.0 165.0 3.0 5 81 200 24 21.6 - 26.4 101 10 15.0 133.0 2.5 5 82 200 24 21.6 - 26.4 111 10 8 75 200 !5.0 !200.0 !4.0 24 21.6 - 26.4 102 10 5 81 200 !12.0 !83.0 !1.5 24 21.6 - 26.4 100 10 5 82 200 !15.0 !66.0 !1.0 48 43.2 - 54.8 28 6 3.3 500.0 10.0 8 74 100 48 43.2 - 54.8 27 6 5.0 400.0 8.0 8 77 100 48 43.2 - 54.8 26 6 12.0 165.0 3.0 5 81 100 48 43.2 - 54.8 25 6 15.0 133.0 2.5 5 82 100 48 43.2 - 54.8 28 6 8 75 100 !5.0 !200.0 !4.0 48 43.2 - 54.8 26 6 5 81 100 !12.0 !83.0 !1.5 48 43.2 - 54.8 25 6 5 82 100 !15.0 !66.0 !1.0 Model Number G201I G202I G203I G204I G205I G206I G207I G211I G212I G213I G214I G215I G216I G217I G221I G222I G223I G224I G225I G226I G227I G231I G232I G233I G234I G235I G236I G237I Notes: Derating Curve 1. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 2. These units do not require external components to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (4.7 µF to 10 µF) may be used to reduce ripple. 100 Output Power % 80 Mechanical Dimensions 60 40 20 Side “T” 0 -40 -20 0 5 0.12 (3.05) 0.60 (15.24) 0.80 (20.32) 1 7 0.40 (10.2) Bottom 10 14 0.01 (0.25) 25 35 45 55 65 75 85 95 105 Ambient Temperature 1C Pin Connections 0.10 (2.5) 0.10 (2.54) 15 9 8 0.01 (0.25) 0.05 (1.25) Note: “T” = 0.27 (6.85) For 5, 12 & 24 VDC Input Models 0.30 (7.50) For 48 VDC Input Models MicroPower Direct Pin Single Dual 1 -Vin -Vin 7 NC NC 8 +Vout +Vout 9 No Pin Common 10 -Vout -Vout 14 +Vin +Vin Capacitive Load Single Output Dual Output µF Max µF Max 470 !390 NC = No Connection Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the top of the unit 232 Tosca Drive, Stoughton, MA 02072 www.micropowerdirect.com [email protected] phone: (781) 344 - 8226 * fax: (781) 344 - 8481