DIP Switches End Stackable DIP Switches DX5 Series DX5S SMT Terminals A 2.80±0.30 [0.1102±0.0118] 1.22 [0.0480] 2.54 [0.1000] 7.62 [0.3000] 6.00 [0.2362] 0.20 [0.0079] 0.40 [0.0157] B 3.50±0.25 [0.1378±0.0098] DX5T7 THT Terminals Pitch 7.62mm TYP 4.50[0.1772] 8.50[0.3346] DX5T8 THT Terminals Pitch 8.50mm DX5J SMT Terminals J-Bending How to order: 1 2 3 4 5 DX5 1 S T7 T8 J 2 RA RC 3 01 02 03 TYPE OF TERMINALS: SMT THT Pitch 7.62mm THT Pitch 8.50 mm SMT J-Bending (Only 4, 8 & 10 positions) ACTUATOR TYPE: Raised Actuator Recessed Actuator NO. OF POSITIONS: 1 Positions 2 Positions 3 Positions [email protected] 04 05 06 07 08 09 10 12 4 N T 5 TB TR 4 Positions 5 Positions 6 Positions 7 Positions 8 Positions 9 Positions 10 Positions 12 Positions SEAL: Regular (Standard) Top Tape Sealed (Only for recessed actuators) PACKAGE STYLE: Tube Tape & Reel (Only for SMT terminals) All dimensions are in millimeters, bracketed dimensions are in inches. General tolerances max. ± 0.20mm. www.greatecs.com 1 DIP Switches End Stackable DIP Switches DX5 Series SPECIFICATIONS 1.Style: This specification describes "DUAL IN-LINE PACKAGE SWITCHES" mainly used as signal switch of electric devices with the general requirements of mechanical and electrical characteristics. 1.1 Operating Temperature Range : -20ɗ ~ +85ɗ 1.2 Storage Temperature Range : -40ɗ ~ +85ɗ 2. Current Range : 2.1 Non-Switching : 100mA, 50V DC 2.2 Switching : 25mA , 24V DC 3. Type of Actuation: Actuated by sliding 4. Test Sequence : ELECTRIC PERFORMANCE ITEM DESCRIPTION 1 2 3 4 MECHANICAL PERFORMANCE 5 6 TEST CONDITIONS Visual By visual examination check without Examination any out pressure & testing. REQUIREMENTS There shall be no defects that affect the serviceability of the product. 1)To be measured between the two terminals associated with each Contact switch pole. 100m max. (initial) Resistance 2)Measurements shall be made with a 1kHz shall current contact resistance meter. Insulation 500V DC, 1 minute ± 5 sec. 100M min. Resistance 500V AC (50Hz or 60 Hz) shall be Dielectric There shall be no applied between all the adjacent withstandbreakdown or terminals and between the terminal ing Voltage flashover. and the frame for 1 minute. Capacitance 1 MHz ± 10 kHz 5 pF max. Applied in the direction of operation. ONĺOFF 1000gf max Operation OFFĺON Force Ȑ9.8N maxȑ [email protected] www.greatecs.com 2 DIP Switches End Stackable DIP Switches 7 Stop Strength DX5 Series A static load of 1 kgf is applied in the operating direction and pulling direction operated for a period of 15 seconds. There shall be no sign of damage mechanically. MECHANICAL PERFORMANCE 1)Soldering Temperature : Soldering Heat 8 Resistance 9 10 DURABILITY 11 12 PROD SERIES TEMP TIME THROUGH HOLE TYPE 260ɗ±5ɗ 5±1 sec. SMT TYPE SEE PAGE 4 1)Contact Resistance : 200m͈Max 2)As shown in item 3~6 2)Duration of Solder Immersion: 5±1 sec. 3)Frequency of Soldering Process: 2 times max. (PCB is 1.6mm in thickness.) Shall be vibrated in accordance with Method 201A of MIL-STD-202F 1)Frequency: 10-55-10 Hz 1 min/cycle. As shown in item 2~6 Vibration 2)Direction: 3 vertical directions including the direction of operation. 3)Test Time: 2 hours each direction. Shall be shocked in accordance with Method 213B condition A of MIL-STD-202F 1)Acceleration: 50G. Shock As shown in item 2~6 2)Action Time : 11 ± 1 m sec. 3)Testing Direction: 6 sides. 4)Test cycle: 3 times in each direction THT Soldering Temperature:245±3ɗ Lead-Free solder烉M705E JIS Z 3282 No anti-soldering and the Class A coverage of dipping into Solderability (Tin 96.5%炻Silver 3%炻Copper 0.5%) solder must more than 75% SMT SEE PAGE 4 Flux: 5-10 seconds. was requested. Duration of solder Immersion: 5±1 sec. Measurements shall be made following 1)As show in item 3,4 the test set forth below: Operation 1)25 mA, 24V DC resistive load 2)Contact Resistance: )2)Rate of Operation: 15~20 cycles/ minute 500m max. Life 3)Cycle of Operation: 2000 cycles. (final-after test) [email protected] www.greatecs.com 3 DIP Switches End Stackable DIP Switches WEATHER-PROOF 13 Resistance Low Temperature Resistance High 14 Temperatur e DX5 Series Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour As shown in item 2~6 before measurements are made : 1)Temperature : -40ɗ±3ɗ 2)Time: 96 hours Following the test set forth below the sample shall be left in normal temperature 1)As shown in item 3~6 and humidity conditions for an hour 2)Contact Resistance: before measurements are made : 100m max. 1)Temperature : 85ɗ±2ɗ 2)Time: 96 hours Following the test set forth below the sample 1)As shown in item 4,6 2)Contact Resistance: shall be left in normal temperature and 100m max. humidity conditions for an hour before Resistance 3)Insulation Resistance: 15 Humidity measurements are made : 1)Temperature : 40ɗ±2ɗ 10M min. 2)Relative Humidity :90~95% 3)Time: 96 hours 5. SOLDERING CONDITIONS: ˍġ Condition for Soldering – SMT Terminals MAX 260° 255° 230° 150° Room Temperature 120~150sec 5~10sec 60sec TIME(sec) Ŷ The condition mentioned above is the temperature on the Cu foil of the P.C.B surface. There are cases where board’s temperature greatly differs from switch’s surface temperature depending on board’s material, size, thickness, etc. Care, therefore, should be used not to allow switch’s surface temperature to exceed 260ɗ. Ŷ Manual Soldering (THT Terminals) Soldering Temperature Max.350ɗ Continuous Soldering Time Max. 5 seconds Ŷ Precautions in Handling 1. Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch. 2. Don’t clean the switch body except with top tape sealed type, which can only spray of cleaning method from top of s/w. 3. Please make sure that there is no flux rose over the surface of the PCB [email protected] www.greatecs.com 4 DIP Switches End Stackable DIP Switches ITEM DESC. DX5 Series Q’TY MATERIALS TREATMENT REMARK MOLDED BLACK - 1. COVER 1 HIGH – TEMP. THERMOPLASTIC PA-9T UL 94V-0 2. CONTACT * COPPER GOLD PLATED AT CONTACT AREA. - 3. ACTUATOR * THERRMOPLASTIC LCP UL 94V-0 MOLDED WHITE - 4. TERMINAL 1 BRASS GOLD PLATED - 5. BASE 1 HIGH – TEMP. THERMOPLASTIC PA9T UL 94V-0 MOLDED BLACK - 6. TAPE 1 KAPTON - - [email protected] www.greatecs.com 5