CHENMKO ENTERPRISE CO.,LTD CHDTA143XEPT SURFACE MOUNT PNP Digital Silicon Transistor VOLTAGE 50 Volts CURRENT 100 mAmpere APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. FEATURE SC-75/SOT-416 * Small surface mounting type. (SC-75/SOT-416) * High current gain. * Suitable for high packing density. Low colloector-emitter saturation. High saturation current capability. Internal isolated PNP transistors in one package. Built in bias resistor(R1=4.7kΩ, Typ. ) (2) 0.1 0.2±0.05 (3) 1.0±0.1 (1) * * * * 0.1 0.3±0.05 CONSTRUCTION 0.5 1.6±0.2 0.5 0.1 0.2±0.05 0.8±0.1 * One PNP transistors and bias of thin-film resistors in one package. MARKING XE1 0.6~0.9 0.15±0.05 0~0.1 0.1Min. Gnd CIRCUIT In 2 1.6±0.2 1 R2 TR R1 SC-75/SOT-416 3 Out Dimensions in millimeters LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC Supply voltage − -50 V VIN Input voltage -20 +7 V − -100 − -100 − 150 mW O C IO DC Output current IC(Max.) Tamb ≤ 25 OC, Note 1 mA PTOT Total power dissipation TSTG Storage temperature −55 +150 TJ Junction temperature − 150 O C Thermal resistance − 140 O C/W RθJ-S junction - soldering point Note 1. Transistor mounted on an FR4 printed-circuit board. 2003-12 RATING CHARACTERISTIC ( CHDTA143XEPT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIoff) Input off voltage IO=-100uA; VCC=-5.0V -0.3 − − V VI(on) Input on voltage IO=-20mA; VO=-0.3V − − -2.5 V VO(on) Output voltage IO=-10mA; II=-0.5mA − -0.3 V II Input current VI=-5V − -0.1 − -0.18 mA IC(off) Output current VI=0V; VCC=-50V − − -0.5 uA hFE DC current gain IO=-10mA; VO=-5.0V 30 − − R1 Input resistor 3.29 4.7 6.11 KΩ R2/R1 fT Resistor ratio Transition frequency 1.7 − 2.1 250 2.6 − MHz Note 1.Pulse test: tp≤300uS; δ≤0.02. IC=-5mA, VCE=-10.0V f=100MHz = RATING CHARACTERISTIC CURVES ( CHDTA143XEPT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) VO=−0.3V −50 OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) −100 Fig.2 Output current vs. input voltage (OFF characteristics) −20 −10 Ta=−40°C 25°C 100°C −5 −2 −1 −500m −200m −100m −100µ −200µ −500µ −1m −2m −10m −5m −2m −1m −500µ Ta=100°C −200µ 25°C −100µ −50µ −40°C −20µ −10µ −5µ −2µ −1µ −5m −10m −20m −50m −100m VCC=−5V 0 Fig.3 DC current gain vs. output current VO=−5V 200 100 Ta=100°C 25°C −40°C 50 20 10 5 2 1 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A) −1.5 −2.0 −2.5 −3.0 Fig.4 Output voltage vs. output current OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI 1k −1.0 INPUT VOLTAGE : VI(off) (V) OUTPUT CURRENT : IO (A) 500 −0.5 −1 IO/II=20 −500m −200m −100m −50m Ta=100°C 25°C −40°C −20m −10m −5m −2m −1m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m OUTPUT CURRENT : IO (A)