APR3101/2/3 MicroPower Microprocessor Reset Circuit with Manual Reset Features General Description • 1.2V to 6V Input Voltage Range The APR3101/2/3 are designed to monitor voltage • Low Quiescent Current : less Than 1.5 µA • • supplies in µP and digital systems. The quiescent High accuracy detection threshold : ±1.5% Fixed trimmed reset thresholds for 1.5V, 1.75V, 2.32V, 2.63V, 2.93V, 3.08V, 3.9V, 4.38V. Manual Reset Input Reset Timeout Period 250ms Available output configurations current is extremely low, typically 1.5 µA, making it - Open-drain output the device asserts a reset signal for a fixed time pe- - CMOS active high output riod after Vcc rises above the fixed threshold or manual - CMOS active low output reset is deasserted. The APR3101/2/3 series is avail- • SOT-23-5 package able with three output stage versions:APR3101 push- • No external components • • • ideal for portable battery operated equipment. The APR3101/2/3 operate by monitoring the system power supply voltage. When the input voltage drops below a fixed threshold or whenever manual reset is asserted, pull active low output, APR3102 push-pull active high output and APR3103 open drain active low output. The APR3101/2/3 also have a debounced manual reset Applications input that is provided to override the reset monitor. They are also designed to reject fast line transient • • • • Computers glitches on Vcc. The APR3101/2/3 are come in a Cell Phones miniature SOT-23-5 package. Portable Electronics Pin Configuration µP Power Supply Monitoring VCC MR 5 4 1 2 3 GND NC Reset (3101/3) Reset (3102) SOT-23-5 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 1 www.anpec.com.tw APR3101/2/3 Ordering and Marking Information Package Code B : SOT-23-5 Temp. Range I : -40 to 85 ° C Handling Code TR : Tape & Reel Voltage Code : 15 : 1.5V ~ 50 : 5.0V Lead Free Code L : Lead Free Device APR3101/2/3 Lead Free Code ° Handling Code Temp. Range Package Code Voltage Code APR3101/2/3 B : A1/2/3 X X Blank : Original Device Date Code Voltage Code A:1.5V B:1.75V C:2.32V D:2.63V E:2.93V F:3.08V G:3.9V H:4.38V Absolute Maximum Ratings Symbol VCC Parameter VCC to GND Value Unit -0.3 to 6 V VRESET RESET to GND (Push-Pull Output) RESET to GND (Open Drain Output) -0.3 to VCC +0.3 -0.3 to 6 V ICC, IMR Maximum Continuous Input Current 20 mA RESET/RESET Current 20 mA Rate of Rise of VCC 100 V/µs -40 to 150 °C IRESET dVcc/dt TJ Junction Temperature Range TL Lead Temperature (Soldering, 10 second) 260 °C RTH,JA Thermal Resistance – Junction to Ambient 357 °C/W Internally Limited W -65 to +150 °C PD Power Dissipation TSTG Storage Temperature Range Pin Function Descrpition No. 1 2 3 PIN Name GND NC RESET (APR3101/3) RESET (APR3102) Description Ground connection No internal connection RESET output remains low while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold. RESET output remains high while VCC is below the reset threshold and remains so for a fixed time period after VCC raises above the reset threshold. Manual Reset active low input. A logic low signal on MR asserts a reset condition. Asserted reset continues as long as MR is low and for a fixed time period after MR returns high. 5 VCC Supply Voltage (+1.2V to +6V) Note: The pin sequence here might not be correct for all different package types, and please refer pin configuration in page1 for correct pin assignment. 4 MR Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 2 www.anpec.com.tw APR3101/2/3 Block Diagram MR Vc c Reset Generator + Timer RESET Oscillator V REF APR3101 GND MR Vc c Reset Generator + Timer RESET Oscillator VREF APR3102 GND MR RESET Vc c Reset Generator + Timer Oscillator V REF GND Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 APR3103 3 www.anpec.com.tw APR3101/2/3 Part Number Description Part Number APR3101 APR3102 APR3103 Part Description Reset Output Push Pull Active Low with Delay Reset Output Push Pull Active High with Delay Reset Output Open Drain Active Low with Delay Electrical Characteristics VIN = 5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C, VCC = 5V for 4.38V versions, VCC = 3.3V for 3.08/2.93V versions, VCC = 3.0V for 2.63V. versions and VCC = 2.5V for 2.32V versions, VCC = 2.0V for 1.75V versions , VCC = 1.8V for 1.5V versions. APR3101/2/3 Symbol Parameter Test Conditions Unit Min. Typ. Max. VCC 1.2 6 Supply Voltage V ICC Supply Current VCC=1.5V~6V 1.5 4 µA T A=-40 to 85°C 3 5 T A=25°C ±1.5% VTH Reset Threshold T A=-40 to 85°C ±2% VHYST Hysteresis Range 20 mV Reset Timeout Period ms TRTP 150 250 350 VOL Reset Output Low ISINK=1.2mA 0.5 V VOH Reset Output High ISOURCE=0.6mA 0.8*VCC TD VCC to Reset Delay VCC=VTH to (VTH-100mV) 25 µS ILE Reset Output Leakage 0.5 µA TMPW MR Minimum Pulse Width 10 µS TMRD MR to Reset Delay 0.5 µS VMIL MR Input Low Threshold 0.4* VCC V VMIH MR Input High Threshold 0.5* VCC RMR 30 47 70 MR Pull-Up resistance KΩ Application Circuit V CC V CC V CC 100k APR3103 RESET GND Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 V CC V CC RESET µ P INPUT APR3101 RESET APR3102 (RESET) GND GND 4 V CC RESET µP INPUT GND www.anpec.com.tw APR3101/2/3 Timing Chart Reset Threshold Reset Threshold Vcc (APR3102) RESET Reset Timeout Period 250ms Vcc to Reset Delay 25us (APR3101/3) RESET Reset Timeout Period 250ms MR to Reset Delay 0.5us MR Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 5 www.anpec.com.tw APR3101/2/3 Typical Characteristics Maximum Transient Duration vs. Reset Threshold Overdrive VTH - VCC Supply Current vs. Supply Voltage 2 Maximum Transient Duration (us) 120 Supply Current (uA) 1.6 1.2 0.8 0.4 0 0 1 2 3 4 5 generate a reset signal 80 60 40 20 never generate a reset signal 0 6 10 100 1000 Reset Threshold Overdrive VTH - VCC (mV) Supply Voltage (V) Output Source Current vs. Reset High Output Voltage Output Sink Current vs. Reset Low Output Voltage 50 70 Vcc=5V 50 Vcc=4V 40 30 Vcc=2.9V 45 60 Output Sink Current (mA) Output Source Current (mA) 100 Vcc=3V 20 10 40 35 Vcc=2.5V 30 25 Vcc=2V 20 15 Vcc=1.5 10 5 0 0 0 1 2 3 4 5 0 6 Reset High Output Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 1 2 3 4 5 6 Reset Low Output Voltage (V) 6 www.anpec.com.tw APR3101/2/3 Typical Characteristics Reset Propagation Delay vs. Temperature 60 1.008 Reset Propagation Delay (us) Normalized Reset Threshold (%) Normalized Reset Threshold vs. Temperature 1.006 1.004 1.002 1 0.998 0.996 0.994 50 40 VOD=100mV 30 20 10 0 -40 -20 0 20 40 60 80 100 120 -40 -20 0 Temperature (°C) 40 60 80 100 120 Temperature (°C) Reset Timeout Period vs. Temperature Supply Current vs. Temperature 3.5 600 3 500 Supply Current (uA) Reset Timeout Period (ms) 20 400 300 200 100 2.5 Vcc=5V 2 1.5 Vcc=3V 1 0.5 0 0 -40 -20 0 20 40 60 80 -40 100 120 Temperature (°C) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 -20 0 20 40 60 80 100 120 Temperature (°C) 7 www.anpec.com.tw APR3101/2/3 Typical Characteristics Power Down Power Up Vcc(2V/div) Vcc(2V/div) RESET(2V/div) RESET(2V/div) MR(2V/div) MR(2V/div) Time (50ms/div) Time (500ms/div) MR to Reset Delay Vcc to RESET Delay Vcc(2V/div) Vcc(0.5V/div) Vcc=V TH to (VTH-100mV) RESET(2V/div) RESET(2V/div) MR(2V/div) Time (0.2us/div) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 Time (10us/div) 8 www.anpec.com.tw APR3101/2/3 Typical Characteristics Manual Reset Vcc(2V/div) RESET(2V/div) MR(2V/div) Time (100ms/div) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 9 www.anpec.com.tw APR3101/2/3 Application Information VCC Transient Rejection the IC is shutdown, and the output becomes a floating state. If it is a trouble, a resistor should be connected from reset output to ground to keep the reset output low (see Figure 1). For The APR3102, a pull-up resistor to VCC is required to keep the valid reset output for VCC below 1.2V.¡@ ¡@ ¡@ The APR3101/2/3 have the function to reject the transient glitches from the power line. The Maximum Transient Duration vs. Reset Threshold Overdrive shows at Typical Characteristics. The transient voltage with the duration under the curve will not generate a reset signal, e.g. a transient of 100mV below the reset threshold voltage have the duration more than 35us, it will generate a reset signal. Connect a 0.1uF bypass capacitor to the VCC pin can improve the transient immunity. VCC VCC Manual Reset Input R E S ET Force the MR low asserts the reset signal, asserted reset continues as long as MR is low and after the 100K GND MR goes high the reset signal is maintained for a fixed timeout period. The MR is internally connected a 47kΩ resistor to VCC, so it can be floating if MR is not used. The MR input also has a debounce time 500ns to avoid the glitches. It allows use of a mechanical switch or a TTL, and CMOS logic signal. Figure 1. Ensuring RESET Valid to VCC = 0 V +3.3V +5.0V Reset Output V CC The APR3101/2/3 have 3 output stage versions: APR3101 is an active low push-pull output,when the VCC drops below the reset threshold or MR goes low, the RESET output generates a low signal. APR3102 is an active high push-pull output, when the VCC drops below the reset threshold or MR goes low; the RESET output generates a high signal (see Timing Chart). APR3103 is an active low open drain output, the RESET output must be connected a pull-up resistor to a supply voltage that is lower than 6V, it suits to use in multiple voltage systems (see Figure 2). The APR3101 RESET output is valid until the VCC=1.2V, below 1.2V Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 A P R3103 MR R E SE T GND V CC 100k R E SE T 5V IN P UT S ystem GND Figure 2. APR3103 Open Drain Output with Multiple Supplies 10 www.anpec.com.tw APR3101/2/3 Packaging Information SOT-23-5 e1 5 4 E1 1 E 3 2 e b D A2 A a A1 Dim A A1 A2 b D E E1 e e1 L L1 L2 N α L 2 L M illimet ers M in. 0.95 0.05 0.90 0.30 2.8 2.6 1.5 Inches M ax. 1.45 0.15 1.30 0.50 3.00 3.00 1.70 M in. 0.037 0.002 0.035 0.011 0.110 0.102 0.059 0.55 0.014 0.7 0.020 0.20 BSC 0.5 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 0.022 0.008 BSC 5 0° M ax. 0.057 0.006 0.051 0.019 0.118 0.118 0.067 0.037BSC 0.074BSC 0.95BSC 1.90BSC 0.35 L 1 0.028 5 10° 11 0° 10° www.anpec.com.tw APR3101/2/3 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP C ritical Zone T L to T P T e m p e ra tu re R am p-up TL tL T sm ax T sm in R am p-down ts Preheat 25 t 25 °C to Peak T im e Classificatin Reflow Profiles Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Mix (Tsmax) - Time (min to max)(ts) Tsmax to TL - Temperature(TL) - Time (tL) Peak Temperature(Tp) Sn-Pb Eutectic Assembly Large Body Small Body Pb-Free Assembly Large Body Small Body 3°C/second max. 3°C/second max. 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds 3°C/second max 183°C 60-150 seconds 217°C 60-150 seconds Time within 5°C of actual Peak 225 +0/-5°C 240 +0/-5°C 245 +0/-5°C 250 +0/-5°C Temperature(tp) Ramp-down Rate 10-30 seconds 10-30 seconds 10-30 seconds 20-40 seconds Time 25°C to Peak Temperature 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 12 www.anpec.com.tw APR3101/2/3 R e lia b ilit y te s t p r o g r a m Te s t ite m S O L D E R A B IL IT Y H O LT PCT TST ESD L a tc h -U p M e th o d M IL -S T D -8 8 3 D -2 0 0 3 M IL -S T D -8 8 3 D -1 0 0 5 .7 J E S D -2 2 - B , A 1 0 2 M IL -S T D -8 8 3 D -1 0 11 .9 M IL -S T D -8 8 3 D -3 0 1 5 .7 JESD 78 D e s c rip tio n 2 45 °C , 5 S E C 1 0 0 0 H rs B ia s @ 1 2 5 ° C 1 6 8 H rs , 1 0 0 % R H , 1 2 1 ° C -6 5 °C ~ 1 5 0 °C , 2 0 0 C y c le s V H B M > 2 K V, V M M > 2 0 0 V 1 0 m s , I tr > 1 0 0 m A Carrier Tape t D P Po E P1 Bo F W Ko Ao D1 T2 J C A B T1 Application SOT-23-5 A B C J 178±1 72 ± 1.0 F D D1 Po 3.5 ± 0.05 1.5 +0.1 1.5 +0.1 4.0 ± 0.1 13.0 + 0.2 2.5 ± 0.15 T1 T2 P E 1.5± 0.3 W 8.0+ 0.3 - 0.3 8.4 ± 2 4 ± 0.1 1.75± 0.1 P1 Ao Bo Ko t 3.2± 0.1 1.4± 0.1 0.2±0.03 2.0 ± 0.1 3.15 ± 0.1 (mm) Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 13 www.anpec.com.tw APR3101/2/3 Cover Tape Dimensions Application SOT- 23 Carrier Width 8 Cover Tape Width 5.3 Devices Per Reel 3000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.3 - Feb., 2004 14 www.anpec.com.tw