DATASHEET IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH Description Features The IDTAS4684 low on-resistance (RON), low voltage, dual single-pole/double-throw (SPDT) analog switch operates from a single +1.8 V to +5.5 V supply. The IDTAS4684 features a 0.5Ω (max) RON for its NC switch and a 0.8Ω (max) RON for its NO switch at a +2.7 V supply. It also features break-before-make switching action (2 ns) with tON = 50 ns and tOFF = 40 ns at +3 V. The digital logic inputs are 1.8 V logic-compatible with a +2.7 V to +3.3 V supply. Comes in a 12-bump CSP package. • • • • • • • • • • • • • Applications • • • • • • • Speaker headset switching MP3 players Battery-operated equipment Audio and video signal routing PCMCIA cards Cellular phones Modems +1.8 V to +5.5 V single-supply operation Rail-to-rail signal handling 1.8 V logic compatibility RON match between channels: 0.06Ω (max) RON flatness over signal range: 0.15Ω (max) NCx Switch RON: 0.5Ω max (+2.7 V Supply) NOx Switch RON: 0.8Ω max (+2.7 V Supply) Low crosstalk: -68dB (100 kHz) High Off-isolation: -64dB (100 kHz) THD: 0.03% 50 nA (max) supply current Low leakage currents: 1 nA (max) at TA = +25°C 12-bump, 0.5 mm-Pitch UCSP package Block Diagram IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 1 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Pin Assignment (CSP) A B C 1 2 3 4 Truth Table IN NO NC 0 OFF ON 1 ON OFF Note: Switches shown for logic “0” input. Pin Descriptions Pin Numbers Pin Name Pin Description A1 NC1 Analog switch. Normally closed terminal 1. A2 IN1 Digital control input 1. A3 COM1 A4 NO1 Analog switch. Normally open terminal 1. B1 GND Ground. B2 NC No connect. B3 NC No connect. B4 V+ Positive supply voltage input. C1 NC2 Analog switch. Normally closed terminal 2. C2 IN2 Digital control input 2. C3 COM2 C4 NO2 Analog switch. Common terminal 1. Analog switch. Common terminal 2. Analog switch. Normally open terminal 2. IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 2 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the IDTAS4684. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. All voltages referenced to ground. Symbol Min Max Unit V+, IN -0.3 +6 V COM, NO, NC -0.3 (V+ + 0.3) V NO, NC, COM Rating Continuous current ±300 Peak current (pulsed at 1ms, 50% duty cycle) ±400 Peak current (pulsed at 1ms, 10% duty cycle) ±500 Continuous power dissipation (TA = +70°C) and 12-bump UCSP (derate 11.4mW/°C above +70°C) +909 mW 0 +70 °C -65 +150 °C Lead temperature (soldering, 10s) +300 °C Bump temperature (soldering, infrared, 15s) +200 °C Vapor phase (60s) +215 °C Operating temperature range TSTG Storage temperature range IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 3 IDTAS4684 mA REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Electrical Characteristics Unless stated otherwise, V+ = 2.7 V to 3.3 V, VIH = 1.4 V, VIL = 0.5 V, TA = TMIN to TMAX. Typical values are at +3 V and 25°C Parameter Symbol Conditions TA Min. TMIN to TMAX 0 Typ. Max. Units Analog Switch Analog Signal Range VNO, VNC, VCOM NC On-Resistance RON(NC) V+ = 2.7 V, ICOM = 100 mA, VNC = 0 to V+; Note 3 NO On-Resistance RON(NO) V+ = 2.7 V, ICOM = 100 mA, VNO = 0 to V+; Note 3 On-Resistance Match between channels RON V+ = 2.7 V, ICOM = 100 mA, VNO or VNC = 1.5 V; Notes 3, 4 +25°C 3.0 TMIN to TMAX V+ V 0.5 Ω 0.5 +25°C 0.45 TMIN to TMAX 0.8 Ω 0.8 +25°C 0 0.6 Ω TMIN to TMAX 0.6 NC On-Resistance Flatness RFLAT(NC) V+ = 2.7 V, ICOM = 100 mA, VNC = 0 to V+; Note 5 TMIN to TMAX 0.15 Ω NO On-Resistance Flatness RFLAT(NO) V+ = 2.7 V, ICOM = 100 mA, VNO = 0 to V+; Note 5 TMIN to TMAX 0.35 Ω -1 +1 nA -10 +10 -2 +2 -20 +20 NO or NC Off-leakage Current COM On-leakage Current INO(OFF) or INC(OFF) ICOM(ON) V+ = 3.3 V, VNO or VNC = 3 V, 0.3 V +25°C VCOM = 0.3 V, 3 V TMIN to TMAX V+ = 3.3 V, VNO or VNC = 3 V, 0.3 +25°C V, or floating TMIN to TMAX VCOM = 0.3 V, 3 V, or floating nA Dynamic Characteristics Turn-on Time tON V+ = 2.7 V, VNO or VNC = 1.5 V, RL = 50Ω, CL = 35 pF Turn-off Time tOFF V+ = 2.7 V, VNO or VNC = 1.5 V, RL = 50Ω, CL = 35 pF Break-Before-Make-Delay tBBM V+ = 2.7 V, VNO or VNC = 1.5 V, RL = 50Ω, CL = 35 pF Charge Injection Q +25°C 30 TMIN to TMAX +25°C 25 TMIN to TMAX TMIN to TMAX 2 50 ns 60 ns 30 ns 40 ns 15 ns COM = 0, RS = 0, CL = 1 nF +25°C 200 pC Off-Isolation VISO CL = 5 pF; RL = 50Ω, f = 100 kHz, VCOM = 1 VRMS, Note 6 +25°C -64 dB Crosstalk VCT f = 100 kHz, RL = 50Ω, CL = 5 pF, VCOM = 1 VRMS +25°C -68 dB Total Harmonic Distortion THD RL = 600Ω, IN = 2 V p-p, f = 20Hz to 20 kHz +25°C 0.03 % NC Off-Capacitance CNC(OFF) f = 1 MHz +25°C 84 pF NC Off-Capacitance CNO(OFF) f = 1 MHz +25°C 37 pF NC On-Capacitance CNC(ON) f = 1 MHz +25°C 190 pF NC On-Capacitance CNO(ON) f = 1 MHz +25°C 150 pF IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 4 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH Parameter ANALOG SWITCH Symbol Conditions TA Min. 1.4 Typ. Max. Units Digital I/O Input Logic HIGH VIH TMIN to TMAX Input Logic LOW VIL TMIN to TMAX IN Input Leakage Current IIN VIN = 0 or V+ V 0.5 V TMIN to TMAX -1 1 µA TMIN to TMAX 1.8 5.5 V V+ = 5.5 V, VIN = 0 or V+, +25°C -50 +50 nA Note 3 TMIN to TMAX -200 Power Supply Power Supply Range V+ Supply Current I+ +0.04 +200 Notes: 1. The algebraic convention used in this data sheet is where the most negative value is a minimum and the most positive value a maximum. 2. UCSP parts are 100% tested at +25°C only and guaranteed by design and correlation at the full hot-rated temperature. 3. Guaranteed by design. 4. RON = RON(MAX) - RON(MIN), between NC1 and NC2 or between NO1 and NO2. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the specified analog signal ranges. 6. Off-isolation = 20log10 (VCOM / VCO), VCOM = output, VCO = input to off switch. IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 5 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Test Circuits and Timing Diagrams Overvoltage Protection Using Two External Blocking Diodes Switching Time IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 6 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Break-Before-Make Interval Charge Injection IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 7 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH On-Loss, Off-Isolation, and Crosstalk Channel Off/On Capacitance IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 8 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Marking Diagram (CSP) IDTAS4 684AHG 0633AAH Notes: 1. “Z” is the device step (1 to 2 characters). 2. YYWW is the last two digits of the year and week that the part was assembled. 3. “$” is the assembly mark code. 4. “G” after the two-letter package code designates RoHS compliant package. 5. “I” at the end of part number indicates industrial temperature range. 6. Bottom marking: country of origin if not USA. IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 9 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Package Outline and Package Dimensions (12-bump CSP) Package dimensions are kept current with JESD Publication No. 95-1, IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 10 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Ordering Information IDT XXXXXX Device Type XXX Package X Temp. Range X Shipping Carrier 8 Blank Tape and Reel Tray Blank Commercial (0 to +70°C) AHG Chip Scale Package AS4684 0.5Ω Low Voltage, Dual SPDT Analog Switch IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 11 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Revision History Rev. Originator Date Description of Change B 10/31/06 Created datasheet in new template; added marking diagram. C 11/15/06 Removed DFN package and ordering information. IDT™ 0.5 OHM, DUAL SPDT ANALOG SWITCH 12 IDTAS4684 REV C 111506 IDTAS4684 0.5 OHM, DUAL SPDT ANALOG SWITCH ANALOG SWITCH Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 408-284-4522 [email protected] Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA