REVISION G IPD1-XX-D-X FIG. 1 C1 IPD1-06-D SHOWN No OF POSITIONS -02 THRU -25 (PER ROW) [SEE FIG. 2 FOR -02 POSITION] .007 .003 ((No OF POSITIONS x .100) + .055) .078±.010 .050 .035±.010 C2 G DO NOT SCALE FROM THIS PRINT *NOT RELEASED FOR PRODUCTION +.005 .08 .220 SEE NOTE 11 .050 (TYP) 'C' .0775 (4 PLCS) .350 C3 ((No OF POSITIONS -1) x .100) .100 "A" 07 "A" .002 .003 01 02 C4 G .250±.002 GATE PADS (SEE NOTE 9) 'B' 1. C REPRESENTS A CRITICAL DIMENSION. 2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN, APPROXIMATELY .150 x .094 (BOTH SIDES). 3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER DESIGNATION LOCATED WHERE SHOWN. 4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE SURFACE OF THE PART. 5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES. 6. MAX ALLOWABLE BOW: SEE TABLE 1. BOW TO BE MEASURED AT MIDLINE OF PART. 7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.002, UNLESS OTHERWISE STATED. 8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING 2, 3 AND 4 POSITIONS. SIZE AND DEPTH SIMILAR TO POSITION 1 INDICATOR. 9. GATE PADS MUST BE RECESSED .005. 10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1 INDICATOR & GATE PADS. 11. POSITION 1 INDICATOR TO BE RAISED .005 MAX, NOT PRESENT ON 2 POSITION OPTION. 12. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES). 13. MOLD DESIGNER HAS DISCRETION OVER RIB LOCATION. STEEL PRINT SETUP SHEET MUST SHOW RIB CONFIGURATION FOR EACH PART NUMBER. 14. PART MUST DRAFT INWARD FROM BOTTOM TO TOP OF STACK. 15. ALL DIMENSIONS TO BE SYMMETRIC ABOUT CENTERLINE WITHIN .0015 UNLESS OTHERWISE STATED. FIG. 3 IPD1-06-D-P SHOWN (SAME AS FIG. 1, EXCEPT AS SHOWN) 01 02 "J" 'A' .0723 (SEE NOTE 14) .0923 (SEE NOTE 14) "B" 'H' 'F' SEE NOTE 8 'E' 07 PARTING LINE C5 .4800±.0020 ROW SPECIFICATION -D: DOUBLE NOTES: .505 - .000 POLARIZATION OPTION -P: POLARIZED (NOT AVAILABLE WITH -K OPTION) (LEAVE BLANK FOR NO POLARIZATION) (SEE FIG. 3) *-K: KEYED POLARIZATION (NOT AVAILABLE WITH -P OPTION) (SEE SHEET 2, FIG. 4) "J" .045 .100±.005 "B" SEE NOTE 2 .255 'D' SEE NOTE 3 +.002 .059 - .001 C6 SECTION "A"-"A" .020 (2 PLCS) 'G' 12 SEE NOTE 12 11 08 07 .050 (TYP) .112 .082 .255 SECTION "B"-"B" UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ANGLES .XX: .01 [.3] 2 .XXX: .003 [.08] .XXXX: .0015 [.038] MATERIAL: 05 04 03 02 01 .050 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING ZYTEL 103FHS, COLOR: WHITE 06 SECTION "J"-"J" SHEET SCALE: 2:1 MAX REGRIND: 25% MAX FLASH ALLOWED: .004 MAX GATE VESTIGE: .002 c:\enterprisevault\DWG\MISC\MKTG\IPD1-XX-D-X-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: .100 SHROUDED CONTACT BODY DWG. NO. BY: CHAD F IPD1-XX-D-X 03/05/2002 SHEET 1 OF 2 REVISION G C7 .0187 .0400 (TYP) 15° (TYP) .060 .075±.002 .100 REF C8 .145±.002 .035 C9 R.025 .0305 (TYP) .0400 (TYP) .1000 (TYP) .0310 SQ (TYP) C10 .225±.005 .085 .030 .0800 (TYP) .145 DETAIL 'C' SCALE 5 : 1 18° (TYP) .0200 +.003 .0850 - .000 (TYP) +.003 .0750 - .000 (TYP) DETAIL 'G' SCALE 5 : 1 DETAIL 'D' SCALE 5 : 1 C11 DETAIL 'B' SCALE 5 : 1 DETAIL 'A' SCALE 3 : 1 +.0030 .0895 - .0000 C12 +.002 .069 - .001 34° FIG. 2 -02 POSITION (SAME AS FIG. 1, UNLESS OTHERWISE STATED) .076 30° (TYP) +.000 .110 - .003 2° REF .006 (TYP) .015 20° .0100 .020 (TYP) .005 .200 .135 +.001 C13 .0020 .105 - .003 .1300 .250 .4550 DETAIL 'H' SCALE 12 : 1 .0250±.005 30° R.025 (TYP) .030 .0100 C14 .041 .325 G FIG. 4 -K: KEYED POLARIZATION ( IPD1-06-D-K SHOWN) (SAME AS FIG. 1, UNLESS OTHERWISE STATED) .068 15° (TYP) .0735 .031 DETAIL 'F' SCALE 4 : 1 DETAIL 'E' SCALE 8 : 1 .0300 NOT RELEASED FOR PRODUCTION "N" PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: DO NOT SCALE DRAWING 2° "N" SECTION "N"-"N" SCALE 4 : 1 SHEET SCALE: 2:1 c:\enterprisevault\DWG\MISC\MKTG\IPD1-XX-D-X-MKT.SLDDRW DWG. NO. .100 SHROUDED CONTACT BODY IPD1-XX-D-X BY: CHAD F 03/05/2002 SHEET 2 OF 2