Model B0430J50100AHF Rev C Ultra Low Profile 0805 Balun 50Ω to 100Ω Balanced Description The B0430J50100AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed specifically for differential inputs and output locations on next generation A to D and D to A Converter IC’s in an easy to use surface mount package, covering 400 MHz–3000 MHz. The B0430J50100AHF is ideal for high volume manufacturing and delivers higher performance than traditional wire wound baluns. The B0430J50100AHF has an unbalanced port impedance of 50Ω and a 100Ω balanced port impedance. This transformation enables single ended signals to be applied to differential ports. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0430J50100AHF is available on tape and reel for pick and place high volume manufacturing. Note that for optimal performance, the B0430J50100AHF should be used with a 10 pF series capacitor on the unbalanced port as shown in p. 2 & 3. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • • 400 – 3000 MHz 0.7mm Height Profile 50 Ohm to 2 x 50 Ohm Low Insertion Loss Designed for A-D and D-A Converters Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature 400 Typ. 50 100 9.9 3.4 0.7 7 25 8.4 Max Unit 3000 MHz Ω Ω dB dB dB Degrees dB Watts ºC 4.0 1.4 12 0.4 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.04±0.10 0.64±0.06 1 2 3 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation GND Unbalanced GND Balanced Port NC Balanced Port Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0430J50100AHF Rev C Typical Performance: 300 MHz. to 3100 MHz. with an external 10 pF capacitor Unbalanced Port 50Ω Return Loss - Input 0 -3 -6 -9 -12 [dB] -15 -18 -21 -24 -27 -30 -33 3100 2900 2700 2500 2300 2100 1900 Amplitude Balance Insertion Loss 0 2 -0.3 1.5 -0.6 -0.9 1 -1.2 0.5 [dB] -1.5 -1.8 -2.1 0 -0.5 -2.4 -2.7 -1 -3 -1.5 -3.3 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 1100 900 700 500 300 700 -2 -3.6 500 Frequency [MHz] Frequency [MHz] Phase Balance CMRR 0 20 -3 15 -6 10 -9 -12 5 [dB] -15 0 -18 -21 -5 -24 -10 -27 -30 -15 -33 -20 Frequency [MHz] 3100 2900 2700 2500 2300 2100 1900 1700 1300 1100 900 700 500 300 3100 2900 2700 2500 2300 2100 1900 1700 1500 1300 900 1100 700 500 300 -36 1500 [dB] 1700 Frequency [MHz] Schematic of BD0430J50100AHF with 10 pF capacitor on unbalanced port (pin #2) deg 1500 1300 1100 900 700 300 500 -36 Balanced Port 50Ω Balanced Port 50Ω Frequency [MHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0430J50100AHF Rev C Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. This component requires a 10 pF capacitor to be mounted in front of the unbalanced port (Pin 2) of the balun as shown in the drawing below for optimum performance. The capacitor should be placed as close as possible to the balun to minimize transmission line effects as shown in the suggested PCB footprint below. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Dimensions are in Millimeters Mounting Footprint Circuit Pattern Footprint Pad (s) Solder Resist 0402 Capacitor 6x .41 .04 6x .33 .66 3x Transmission lines 4x .25 3x Plated thru holes to ground Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0430J50100AHF Rev C Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 2.41 8.00 1.60 4.00 .25 Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282