Power for C5504/05 SLVA401A C5504/05 Power Spec Table Pin Name LDOI 3 Voltage (V) Max Current 4 (mA) 1.8 - 3.6 5 Tolerance Sequencing Order Comments Supplying ANA LDO (supplies VDDA_ANA and VDDA_PLL). Typical Core Power Consumption: Core CVDD1, CVDDRTC1 1.05 / 1.30 500 -5%, +10% 1.3V 70 -5%, +10% DVDDIO, DVDDRTC 1.8 / 2.5 / 2.8 / 3.3 300 -10%, +10% DVDDEMIF 1.8 / 2.5 / 2.8 / 3.3 245 -10%, +10% 3.3V 55 -5%, +5% USB_VDD1P3, USB_VD DA1P3 USB_VDDOSC, USB_VDDA3P3, USB_VDDPLL - 0.22mW/MHz for 75% DMAC + 25% NOP (CVDD =1.3V @ 100MHz, Room Temp) - 0.14mW/MHz for 75% DMAC + 25% NOP (CVDD =1.05V @ 100MHz, Room Temp) 12 For best performance, these voltages should be powered by a LDO in order to minimize noise. NOTES: 1) CVDD & CVDDRTC can be 1.05Vor 1.30V for ≤60MHz operation and 1.30V for operating higher than 60MHz 2) Power Supply Sequencing: No sequencing is required (for further details, see section 5.3.1 of the data sheet) 3) If GPAIN pins are used as general purpose outputs, the internal ANA_LDO must not be used as the max current capability of ANA_LDO can be exceeded. In this case use an external regulator to supply VDDA_ANA.. 4) This column shows the maximum design current of each power domain. See the C5505/04 data sheet for actual current consumptions of some usage cases. See the data in the “Comments” column above. SLVA401A Power Options for C5504/05 *Please visit ti.com/processorpower for COMPLETE power solutions Highest Efficiency, Low Cost Integrated PMIC High-Efficiency, Dual DCDC + PMIC VIN: 3.6V – 6V TPS65054 TPS65054 VIN: 3.6V – 5V Multi-output Multi-output DCDC DCDC1 DCDC Converter Converter DCDC2 Vbat LDO1 VINDCDC1/2 VIN_LDOx LDO2 EN_LDOx LDO3 LDO4 Lowest Cost, Dual DCDC @ 3.3V & 1.3V VIN: 12V TPS62400 TPS62400 Dual Dual 600mA/400mA 600mA/400mA DCDC DCDCConverter Converter DCDC1 EN1 EN2 DCDC2 TPS62410 TPS62410 VIN: 3.6V – 6V Dual Dual 600mA/400mA 600mA/400mA DCDC Converter DCDC Converter TPS65001 TPS65001 Triple Triple DCDC DCDCConverter Converter With WithSVS SVS EN2 EN1 DCDC1 DCDC2 • 2 DCDC + 4 LDO’s in 4x4mm QFN • 2.25MHz for Small Inductors • 180˚ Out-of-Phase Operation SLVA401A TPS62400 TPS62400 Dual Dual 600mA/400mA 600mA/400mA DCDC DCDCConverter Converter EN2 EN1 DCDC1 DCDC2 LDO1 LDO2 • 3.6 – 6V input voltage • Up to 95% Efficiency • Efficiency up to 95% • 2.25MHz for Small Inductors • 2.25MHz for Small Inductors • Integrated SVS EN Dual Dual250mA 250mALDO LDO LDO1 LDO2 TPS62111 TPS62111 1.5 1.5 DCDC DCDCConverter Converter TPS71202 TPS71202 DCDC1 EN High Input Voltage, DCDC Converters • Input voltage capable up to 17V • PFM mode for high efficiency during light loads • Low-Noise LDO (32uVrms) Highest Efficiency, Single PMIC (TPS65054) Vin: 3.6V – 5.5V TPS65054 C5514/15 1.8 / 2.5 / 2.8 / 3.3V @ 300mA 1.05V / 1.3V @ 500mA 1.8 - 3.3V @ 5mA 1.8 / 2.5 / 2.8 / 3.3V @ 245mA DVDDIO, DVDDRTC CVDD, CVDDRTC LDOI DVDDEMIF OPEN 1.3V @ 70mA 3.3V @ 55mA SLVA401A USB_VDD1P3, USB_VDDA1P3, USB_VDDOSC, USB_VDDA3P3, USB_VDDPLL High Efficiency, Low part count (TPS62400 + TPS65001) Vin: 3.6V – 5.5V C5504/05 TPS62400 400mA 600mA 1.8 / 2.5 / 2.8 / 3.3V @ 300mA 1.05V / 1.3V @ 500mA DVDDIO, DVDDRTC CVDD, CVDDRTC TPS65001 600mA 1.8 / 2.5 / 2.8 / 3.3V @ 245mA DVDDEMIF /PG 200mA 200mA 3.3V @ 55mA 1.8 - 3.3V @ 5mA 1.3V @ 70mA SLVA401A USB_VDDOSC, USB_VDDA3P3, USB_VDDPLL LDOI USB_VDD1P3, USB_VDDA1P3, High Efficiency, Lowest cost Reduce rails to 1.3V and 3.3V TPS62410 DVDDIO, DVDDRTC Vin: 3.6V – 5.5V 800mA C5504/05 3.3V @ 605mA DVDDEMIF LDOI USB_VDDOSC, USB_VDDA3P3, USB_VDDPLL 800mA 1.3V @ 500mA 1.3V @ 70mA SLVA401A CVDD, CVDDRTC USB_VDD1P3, USB_VDDA1P3, High Input Voltage C5504/05 TPS62111 3.3V @ 55mA TPS62400 400mA 1.8 - 3.0V @ 5mA 1.8 / 2.5 / 2.8V @ 300mA 1.05V / 1.3V @ 500mA USB_VDDOSC, USB_VDDA3P3, USB_VDDPLL LDOI DVDDIO, DVDDRTC CVDD, CVDDRTC 600mA TPS71202 1.8 / 2.5 / 2.8V @ 245mA 1.3V @ 70mA SLVA401A Note: If DVDDIO, DVDDRTC, DVDDEMIF, LDOI are 3.3V, connect directly to 3.3V DVDDEMIF USB_VDD1P3, USB_VDDA1P3, IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated