M93C86-x M93C76-x M93C66-x M93C56-x M93C46-x 16-Kbit, 8-Kbit, 4-Kbit, 2-Kbit and 1-Kbit (8-bit or 16-bit wide) MICROWIRE serial access EEPROM Datasheet - production data READY/BUSY signal during programming 2 MHz clock rate Sequential read operation Enhanced ESD/latch-up behavior More than 4 million write cycles PDIP8 (BN) More than 200-year data retention Packages – SO8, TSSOP8, UFDFPN8 packages: RoHS-compliant and Halogen-free (ECOPACK®) – PDIP8 package: RoHS-compliant (ECOPACK1®) SO8 (MN) 150 mil width Table 1. Device summary Reference TSSOP8 (DW) 169 mil width M93C46-x M93C56-x M93C66-x UFDFPN8 (MC) 2 x 3 mm M93C86-x Features Part number M93C46-W M93C46-R M93C56-W M93C56-R M93C66-W M93C66-R M93C76-R M93C86-W M93C86-R Memory size 1 Kbit 2 Kbit 4 Kbit 8 Kbit 16 Kbit Supply voltage 2.5 V to 5.5 V 1.8 V to 5.5 V 2.5 V to 5.5 V 1.8 V to 5.5 V 2.5 V to 5.5 V 1.8 V to 5.5 V 1.8 V to 5.5 V 2.5 V to 5.5 V 1.8 V to 5.5 V Industry standard MICROWIRE bus Single supply voltage: – 2.5 V to 5.5 V for M93Cx6-W – 1.8 V to 5.5 V for M93Cx6-R Dual organization: by word (x16) or byte (x8) Programming instructions that work on: byte, word or entire memory Self-timed programming cycle with auto-erase: 5 ms November 2013 This is information on a product in full production. DocID4997 Rev 15 1/33 www.st.com Contents M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Connecting to the serial bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1 Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1.1 Operating supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1.2 Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1.3 Power-up and device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1.4 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.1 Read Data from Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2 Erase and Write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2.1 Write Enable and Write Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2.2 Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2.3 Write All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.2.4 Erase Byte or Word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.2.5 Erase All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 READY/BUSY status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8 Clock pulse counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 11 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 12 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 13 Contents Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DocID4997 Rev 15 3/33 3 List of tables M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. 4/33 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Memory size versus organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Instruction set for the M93C46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Instruction set for the M93C56 and M93C66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Instruction set for the M93C76 and M93C86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Operating conditions (M93Cx6-W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Operating conditions (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Cycling performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Memory cell data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Input and output capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 DC characteristics (M93Cx6-W, device grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 DC characteristics (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 AC characteristics (M93Cx6-W, M93Cx6-R, device grade 6). . . . . . . . . . . . . . . . . . . . . . . 23 AC characteristics (M93Cx6-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 PDIP8 – 8 lead plastic dual in-line package, 300 mils body width, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 SO8 narrow – 8 lead plastic small outline, 150 mils body width, package data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2 x 3 mm, data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 TSSOP8 – 8-lead thin shrink small outline, package mechanical data. . . . . . . . . . . . . . . . 29 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 8-pin package connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bus master and memory devices on the serial bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 M93Cx6 ORG input connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 READ, WRITE, WEN, WDS sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 WRAL sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ERASE, ERAL sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Write sequence with one clock glitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AC testing input output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Synchronous timing (Start and op-code input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Synchronous timing (Read) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Synchronous timing (Write) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 PDIP8 – 8 lead plastic dual in-line package, 300 mils body width, package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 SO8 narrow – 8 lead plastic small outline, 150 mils body width, package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2 x 3 mm, outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 TSSOP8 – 8 lead thin shrink small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . 29 DocID4997 Rev 15 5/33 5 Description 1 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Description The M93C46 (1 Kbit), M93C56 (2 Kbit), M93C66 (4 Kbit), M93C76 (8 Kbit) and M93C86 (16 Kbit) are Electrically Erasable PROgrammable Memory (EEPROM) devices accessed through the MICROWIRE bus protocol. The memory array can be configured either in bytes (x8b) or in words (x16b). The M93Cx6-W devices operate within a voltage supply range from 2.5 V to 5.5 V and the M93Cx6-R devices operate within a voltage supply range from 1.8 V to 5.5 V. All these devices operate with a clock frequency of 2 MHz (or less), over an ambient temperature range of -40 °C / +85 °C. Table 2. Memory size versus organization Device Number of bits Number of 8-bit bytes Number of 16-bit words M93C86 16384 2048 1024 M93C76 8192 1024 512 M93C66 4096 512 256 M93C56 2048 256 128 M93C46 1024 128 64 Figure 1. Logic diagram VCC D Q C M93Cx6 S ORG VSS AI01928 Table 3. Signal names Signal name 6/33 Function Direction S Chip Select Input D Serial Data input Input Q Serial Data output Output C Serial Clock Input ORG Organization Select Input VCC Supply voltage VSS Ground DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Description Figure 2. 8-pin package connections (top view) M93Cx6 S C D Q 1 2 3 4 8 7 6 5 VCC DU ORG VSS AI01929B 1. See Section 11: Package mechanical data for package dimensions, and how to identify pin-1. 2. DU = Don’t Use. The DU (do not use) pin does not contribute to the normal operation of the device. It is reserved for use by STMicroelectronics during test sequences. The pin may be left unconnected or may be connected to VCC or VSS. DocID4997 Rev 15 7/33 32 Connecting to the serial bus 2 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Connecting to the serial bus Figure 3 shows an example of three memory devices connected to an MCU, on a serial bus. Only one device is selected at a time, so only one device drives the Serial Data output (Q) line at a time, the other devices are high impedance. The pull-down resistor R (represented in Figure 3) ensures that no device is selected if the bus master leaves the S line in the high impedance state. In applications where the bus master may be in a state where all inputs/outputs are high impedance at the same time (for example, if the bus master is reset during the transmission of an instruction), the clock line (C) must be connected to an external pull-down resistor so that, if all inputs/outputs become high impedance, the C line is pulled low (while the S line is pulled low): this ensures that C does not become high at the same time as S goes low, and so, that the tSLCH requirement is met. The typical value of R is 100 k. Figure 3. Bus master and memory devices on the serial bus VSS VCC R SDO SDI SCK Bus master C Q D VCC C Q D VCC VSS R M93xxx memory device R C Q D VCC VSS M93xxx memory device R VSS M93xxx memory device CS3 CS2 CS1 S ORG S ORG S ORG AI14377b 8/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 3 Operating features 3.1 Supply voltage (VCC) 3.1.1 Operating supply voltage (VCC) Operating features Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage within the specified [VCC(min), VCC(max)] range must be applied. In order to secure a stable DC supply voltage, it is recommended to decouple the VCC line with a suitable capacitor (usually of the order of 10 nF to 100 nF) close to the VCC/VSS package pins. This voltage must remain stable and valid until the end of the transmission of the instruction and, for a Write instruction, until the completion of the internal write cycle (tW). 3.1.2 Power-up conditions When the power supply is turned on, VCC rises from VSS to VCC. During this time, the Chip Select (S) line is not allowed to float and should be driven to VSS, it is therefore recommended to connect the S line to VSS via a suitable pull-down resistor. The VCC rise time must not vary faster than 1 V/µs. 3.1.3 Power-up and device reset In order to prevent inadvertent Write operations during power-up, a power on reset (POR) circuit is included. At power-up (continuous rise of VCC), the device does not respond to any instruction until VCC has reached the power on reset threshold voltage (this threshold is lower than the minimum VCC operating voltage defined in Operating conditions, in Section 10: DC and AC parameters). When VCC passes the POR threshold, the device is reset and is in the following state: 3.1.4 Standby Power mode deselected (assuming that there is a pull-down resistor on the S line) Power-down At power-down (continuous decrease in VCC), as soon as VCC drops from the normal operating voltage to below the power on reset threshold voltage, the device stops responding to any instruction sent to it. During power-down, the device must be deselected and in the Standby Power mode (that is, there should be no internal Write cycle in progress). DocID4997 Rev 15 9/33 32 Memory organization 4 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Memory organization The M93Cx6 memory is organized either as bytes (x8) or as words (x16). If Organization Select (ORG) is left unconnected (or connected to VCC) the x16 organization is selected; when Organization Select (ORG) is connected to Ground (VSS) the x8 organization is selected. When the M93Cx6 is in Standby mode, Organization Select (ORG) should be set either to VSS or VCC to reach the device minimum power consumption (as any voltage between VSS and VCC applied to ORG input may increase the device Standby current). Figure 4. M93Cx6 ORG input connection Vcc Vcc Vcc Not connected ORG ORG Vss x16 organization Vss x16 organization ORG Vss x8 organization MSv31690V1 10/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 5 Instructions Instructions The instruction set of the M93Cx6 devices contains seven instructions, as summarized in Table 4 to Table 6. Each instruction consists of the following parts, as shown in Figure 5: READ, WRITE, WEN, WDS sequences: Each instruction is preceded by a rising edge on Chip Select Input (S) with Serial Clock (C) being held low. A start bit, which is the first ‘1’ read on Serial Data Input (D) during the rising edge of Serial Clock (C). Two op-code bits, read on Serial Data Input (D) during the rising edge of Serial Clock (C). (Some instructions also use the first two bits of the address to define the op-code). The address bits of the byte or word that is to be accessed. For the M93C46, the address is made up of 6 bits for the x16 organization or 7 bits for the x8 organization (see Table 4). For the M93C56 and M93C66, the address is made up of 8 bits for the x16 organization or 9 bits for the x8 organization (see Table 5). For the M93C76 and M93C86, the address is made up of 10 bits for the x16 organization or 11 bits for the x8 organization (see Table 6). The M93Cx6 devices are fabricated in CMOS technology and are therefore able to run as slow as 0 Hz (static input signals) or as fast as the maximum ratings specified in “AC characteristics” tables, in Section 10: DC and AC parameters. Table 4. Instruction set for the M93C46 x8 origination (ORG = 0) Instruction Description Start bit Opcode Address (1) Data x16 origination (ORG = 1) Required Address clock (1) cycles Data Required clock cycles READ Read Data from Memory 1 10 A6-A0 Q7-Q0 - A5-A0 Q15-Q0 - WRITE Write Data to Memory 1 01 A6-A0 D7-D0 18 A5-A0 D15-D0 25 WEN Write Enable 1 00 11X XXXX - 10 11 XXXX - 9 WDS Write Disable 1 00 00X XXXX - 10 00 XXXX - 9 ERASE Erase Byte or Word 1 11 A6-A0 - 10 A5-A0 - 9 ERAL Erase All Memory 1 00 10X XXXX - 10 10 XXXX - 9 WRAL Write All Memory with same Data 1 00 01X XXXX D7-D0 18 01 XXXX D15-D0 25 1. X = Don't Care bit. DocID4997 Rev 15 11/33 32 Instructions M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Table 5. Instruction set for the M93C56 and M93C66 Instruction x8 origination (ORG = 0) x16 origination (ORG = 1) OpStart Required Required cod Address Address bit Data clock Data clock e (1) (2) (1) (3) cycles cycles Description READ Read Data from Memory 1 10 A8-A0 Q7Q0 - A7-A0 Q15Q0 - WRITE Write Data to Memory 1 01 A8-A0 D7D0 20 A7-A0 D15-D0 27 WEN Write Enable 1 00 1 1XXX XXXX - 12 11XX XXXX - 11 WDS Write Disable 1 00 0 0XXX XXXX - 12 00XX XXXX - 11 ERASE Erase Byte or Word 1 11 A8-A0 - 12 A7-A0 - 11 ERAL Erase All Memory 1 00 1 0XXX XXXX - 12 10XX XXXX - 11 WRAL Write All Memory with same Data 1 00 0 1XXX XXXX D7D0 20 01XX XXXX D15-D0 27 1. X = Don't Care bit. 2. Address bit A8 is not decoded by the M93C56. 3. Address bit A7 is not decoded by the M93C56. Table 6. Instruction set for the M93C76 and M93C86 x8 Origination (ORG = 0) Instruction Description Start Opbit code Address (1)(2) Data x16 Origination (ORG = 1) Required Address clock (1) (3) cycles Data Required clock cycles READ Read Data from Memory 1 10 A10-A0 Q7-Q0 - A9-A0 Q15-Q0 - WRITE Write Data to Memory 1 01 A10-A0 D7-D0 22 A9-A0 D15-D0 29 WEN Write Enable 1 00 11X XXXX XXXX - 14 11 XXXX XXXX - 13 WDS Write Disable 1 00 00X XXXX XXXX - 14 00 XXXX XXXX - 13 ERASE Erase Byte or Word 1 11 A10-A0 - 14 A9-A0 - 13 ERAL Erase All Memory 1 00 10X XXXX XXXX - 14 10 XXXX XXXX - 13 WRAL Write All Memory with same Data 1 00 01X XXXX XXXX D7-D0 22 01 XXXX D15-D0 XXXX 1. X = Don't Care bit. 2. Address bit A10 is not decoded by the M93C76. 3. Address bit A9 is not decoded by the M93C76. 12/33 DocID4997 Rev 15 29 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 5.1 Instructions Read Data from Memory The Read Data from Memory (READ) instruction outputs data on Serial Data Output (Q). When the instruction is received, the op-code and address are decoded, and the data from the memory is transferred to an output shift register. A dummy 0 bit is output first, followed by the 8-bit byte or 16-bit word, with the most significant bit first. Output data changes are triggered by the rising edge of Serial Clock (C). The M93Cx6 automatically increments the internal address register and clocks out the next byte (or word) as long as the Chip Select Input (S) is held High. In this case, the dummy 0 bit is not output between bytes (or words) and a continuous stream of data can be read (the address counter automatically rolls over to 00h when the highest address is reached). 5.2 Erase and Write data 5.2.1 Write Enable and Write Disable The Write Enable (WEN) instruction enables the future execution of erase or write instructions, and the Write Disable (WDS) instruction disables it. When power is first applied, the M93Cx6 initializes itself so that erase and write instructions are disabled. After a Write Enable (WEN) instruction has been executed, erasing and writing remains enabled until a Write Disable (WDS) instruction is executed, or until VCC falls below the power-on reset threshold voltage. To protect the memory contents from accidental corruption, it is advisable to issue the Write Disable (WDS) instruction after every write cycle. The Read Data from Memory (READ) instruction is not affected by the Write Enable (WEN) or Write Disable (WDS) instructions. 5.2.2 Write For the Write Data to Memory (WRITE) instruction, 8 or 16 data bits follow the op-code and address bits. These form the byte or word that is to be written. As with the other bits, Serial Data Input (D) is sampled on the rising edge of Serial Clock (C). After the last data bit has been sampled, the Chip Select Input (S) must be taken low before the next rising edge of Serial Clock (C). If Chip Select Input (S) is brought low before or after this specific time frame, the self-timed programming cycle will not be started, and the addressed location will not be programmed. The completion of the cycle can be detected by monitoring the READY/BUSY line, as described later in this document. Once the Write cycle has been started, it is internally self-timed (the external clock signal on Serial Clock (C) may be stopped or left running after the start of a Write cycle). The Write cycle is automatically preceded by an Erase cycle, so it is unnecessary to execute an explicit erase instruction before a Write Data to Memory (WRITE) instruction. DocID4997 Rev 15 13/33 32 Instructions M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Figure 5. READ, WRITE, WEN, WDS sequences Read S D 1 1 0 An A0 Qn Q ADDR Q0 DATA OUT OP CODE Write S CHECK STATUS D 1 0 1 An A0 Dn D0 Q ADDR DATA IN BUSY READY OP CODE Write Enable S D Write Disable 1 0 0 1 1 Xn X0 S D OP CODE 1 0 0 0 0 Xn X0 OP CODE AI00878d 1. For the meanings of An, Xn, Qn and Dn, see Table 4, Table 5 and Table 6. 14/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 5.2.3 Instructions Write All As with the Erase All Memory (ERAL) instruction, the format of the Write All Memory with same Data (WRAL) instruction requires that a dummy address be provided. As with the Write Data to Memory (WRITE) instruction, the format of the Write All Memory with same Data (WRAL) instruction requires that an 8-bit data byte, or 16-bit data word, be provided. This value is written to all the addresses of the memory device. The completion of the cycle can be detected by monitoring the READY/BUSY line, as described next. Figure 6. WRAL sequence WRITE ALL S CHECK STATUS D 1 0 0 0 1 Xn X0 Dn D0 Q ADDR DATA IN BUSY READY OP CODE AI00880C 1. For the meanings of Xn and Dn, please see Table 4, Table 5 and Table 6. DocID4997 Rev 15 15/33 32 Instructions 5.2.4 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Erase Byte or Word The Erase Byte or Word (ERASE) instruction sets the bits of the addressed memory byte (or word) to 1. Once the address has been correctly decoded, the falling edge of the Chip Select Input (S) starts the self-timed Erase cycle. The completion of the cycle can be detected by monitoring the READY/BUSY line, as described in Section 6: READY/BUSY status. Figure 7. ERASE, ERAL sequences ERASE S CHECK STATUS D 1 1 1 An A0 Q ADDR BUSY READY OP CODE ERASE ALL S CHECK STATUS D 1 0 0 1 0 Xn X0 Q ADDR BUSY READY OP CODE AI00879B 1. For the meanings of An and Xn, please see Table 4, Table 5 and Table 6. 5.2.5 Erase All The Erase All Memory (ERAL) instruction erases the whole memory (all memory bits are set to 1). The format of the instruction requires that a dummy address be provided. The Erase cycle is conducted in the same way as the Erase instruction (ERASE). The completion of the cycle can be detected by monitoring the READY/BUSY line, as described in Section 6: READY/BUSY status. 16/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 6 READY/BUSY status READY/BUSY status While the Write or Erase cycle is underway, for a WRITE, ERASE, WRAL or ERAL instruction, the Busy signal (Q=0) is returned whenever Chip Select input (S) is driven high. (Please note, though, that there is an initial delay, of tSLSH, before this status information becomes available). In this state, the M93Cx6 ignores any data on the bus. When the Write cycle is completed, and Chip Select Input (S) is driven high, the Ready signal (Q=1) indicates that the M93Cx6 is ready to receive the next instruction. Serial Data Output (Q) remains set to 1 until the Chip Select Input (S) is brought low or until a new start bit is decoded. 7 Initial delivery state The device is delivered with all bits in the memory array set to 1 (each byte contains FFh). DocID4997 Rev 15 17/33 32 Clock pulse counter 8 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Clock pulse counter In a noisy environment, the number of pulses received on Serial Clock (C) may be greater than the number delivered by the master (the microcontroller). This can lead to a misalignment of the instruction of one or more bits (as shown in Figure 8) and may lead to the writing of erroneous data at an erroneous address. To avoid this problem, the M93Cx6 has an on-chip counter that counts the clock pulses from the start bit until the falling edge of the Chip Select Input (S). If the number of clock pulses received is not the number expected, the WRITE, ERASE, ERAL or WRAL instruction is aborted, and the contents of the memory are not modified. The number of clock cycles expected for each instruction, and for each member of the M93Cx6 family, are summarized in Table 4: Instruction set for the M93C46 to Table 6: Instruction set for the M93C76 and M93C86. For example, a Write Data to Memory (WRITE) instruction on the M93C56 (or M93C66) expects 20 clock cycles (for the x8 organization) from the start bit to the falling edge of Chip Select Input (S). That is: 1 Start bit + 2 Op-code bits + 9 Address bits + 8 Data bits Figure 8. Write sequence with one clock glitch S C D An START "0" "1" An-1 An-2 Glitch D0 ADDRESS AND DATA ARE SHIFTED BY ONE BIT WRITE AI01395 18/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 9 Maximum ratings Maximum ratings Stressing the device outside the ratings listed in the Absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions outside those indicated in the operating sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 7. Absolute maximum ratings Symbol TSTG Parameter Min. Max. Unit Ambient operating temperature –40 130 °C Storage temperature –65 150 °C - 260(1) PDIP TLEAD Lead temperature during soldering VOUT Output range (Q = VOH or Hi-Z) –0.50 VCC+0.5 V VIN Input range –0.50 VCC+1 V VCC Supply voltage –0.50 6.5 V - 4000 V VESD See note (2) other packages Electrostatic discharge voltage (human body model)(3) °C 1. TLEAD max must not be applied for more than 10 s. 2. Compliant with JEDEC standard J-STD-020D (for small-body, Sn-Pb or Pb assembly), the ST ECOPACK® 7191395 specification, and the European directive on Restrictions on Hazardous Substances (RoHS directive 2011/65/EU of July 2011). 3. Positive and negative pulses applied on pin pairs, according to the AEC-Q100-002 (compliant with JEDEC Std JESD22-A114, C1 = 100 pF, R1 = 1500 , R2 = 500 ). DocID4997 Rev 15 19/33 32 DC and AC parameters 10 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x DC and AC parameters This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. Table 8. Operating conditions (M93Cx6-W) Symbol VCC TA Parameter Min. Max. Unit Supply voltage 2.5 5.5 V Ambient operating temperature –40 85 °C Min. Max. Unit Supply voltage 1.8 5.5 V Ambient operating temperature –40 85 °C Table 9. Operating conditions (M93Cx6-R) Symbol VCC TA Parameter Table 10. Cycling performance(1) Symbol Ncycle Parameter Write cycle endurance Test conditions Min. Max. TA 25 °C, VCC(min) < VCC < VCC(max) - 4,000,000 TA = 85 °C, VCC(min) < VCC < VCC(max) - Unit Write cycle 1,200,000 1. Cycling performance for products identified by process letter K. Table 11. Memory cell data retention(1) Parameter Data retention Test conditions TA = 55 °C Min. Unit 200 Year 1. For products identified by process letter K. The data retention behavior is checked in production, while the 200-year limit is defined from characterization and qualification results. 20/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x DC and AC parameters Table 12. AC measurement conditions Symbol CL Parameter Min. Load capacitance Max. Unit 100 - pF - Input rise and fall times 50 ns - Input voltage levels 0.2 VCC to 0.8 VCC V - Input timing reference voltages 0.3 VCC to 0.7 VCC V - Output timing reference voltages 0.3 VCC to 0.7 VCC V Figure 9. AC testing input output waveforms M93CXX 0.8VCC 0.7VCC Input voltage levels 0.3VCC 0.2VCC Input and output timing reference levels MS19788V3 Table 13. Input and output capacitance Symbol Parameter COUT Output capacitance CIN Input capacitance Test condition(1) Min Max Unit VOUT = 0V - 8 pF VIN = 0V - 6 pF 1. Sampled only, not 100% tested, at TA = 25 °C and a frequency of 1 MHz. DocID4997 Rev 15 21/33 32 DC and AC parameters M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Table 14. DC characteristics (M93Cx6-W, device grade 6) Symbol ILI Input leakage current ILO Output leakage current ICC ICC1 1. Parameter Operating supply current Standby supply current Test condition (in addition to the conditions defined in Table 8 and Table 12) Min. Max. Unit 0V VIN VCC - ±2.5 µA 0V VOUT VCC, Q in Hi-Z - ±2.5 µA VCC = 5 V, S = VIH, f = 2 MHz, Q = open - 2 mA VCC = 2.5 V, S = VIH, f = 2 MHz, Q = open - 1 mA VCC = 2.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z - 2(1) µA VCC = 5.5 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z - 3(2) µA –0.45 0.2 VCC V 0.7 VCC VCC + 1 V VIL Input low voltage (D, C, S) - VIH Input high voltage (D, C, S) - VOL Output low voltage (Q) VOH Output high voltage (Q) VCC = 5 V, IOL = 2.1 mA - 0.4 V VCC = 2.5 V, IOL = 100 µA - 0.2 V VCC = 5 V, IOH = –400 µA 0.8 VCC - V VCC = 2.5 V, IOH = –100 µA VCC–0.2 - V 5 µA for previous devices identified with the process letter G. 2. Tested only for current devices identified with the process letter K. Table 15. DC characteristics (M93Cx6-R) Symbol Parameter ILI Input leakage current ILO Output leakage current ICC Operating supply current Test condition Min. Max. Unit 0V VIN VCC - ±2.5 µA 0V VOUT VCC, Q in Hi-Z - ±2.5 µA VCC = 5 V, S = VIH, f = 2 MHz, Q = open - 2 mA VCC = 1.8 V, S = VIH, f = 1 MHz, Q = open - 1 mA VCC = 1.8 V, S = VSS, C = VSS, ORG = VSS or VCC, pin7 = VCC, VSS or Hi-Z - 1(1) µA ICC1 Standby supply current VIL Input low voltage (D, C, S) - –0.45 0.2 VCC V VIH Input high voltage (D, C, S) - 0.8 VCC VCC + 1 V VOL Output low voltage (Q) VCC = 1.8 V, IOL = 100 µA - 0.2 V VOH Output high voltage (Q) VCC = 1.8 V, IOH = –100 µA VCC–0.2 - V 1. 2 µA for previous devices identified with process letter G. 22/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x DC and AC parameters Table 16. AC characteristics (M93Cx6-W, M93Cx6-R(1), device grade 6) Test conditions specified in Table 8 and Table 12 Symbol Alt. fC fSK Min. Max. Unit D.C. 2 MHz Chip Select low to Clock high 50 - ns tCSS Chip Select setup time 50 - ns tSLCH tSHCH tSLSH (2) Parameter Clock frequency tCS Chip Select low to Chip Select high 200 - ns tCHCL(3) tSKH Clock high time 200 - ns tCLCH(3) tSKL Clock low time 200 - ns tDVCH tDIS Data in setup time 50 - ns tCHDX tDIH Data in hold time 50 - ns tCLSH tSKS Clock setup time (relative to S) 50 - ns tCLSL tCSH Chip Select hold time 0 - ns tSHQV tSV Chip Select to READY/BUSY status - 200 ns tSLQZ tDF Chip Select low to output Hi-Z - 100 ns tCHQL tPD0 Delay to output low - 200 ns tCHQV tPD1 Delay to output valid - 200 ns tW tWP Erase or Write cycle time - 5 ms 1. All M93Cx6-R devices operate with a clock frequency of 1MHz, as defined in Table 17. Only the new M93Cx6-R devices (identified with the process letter K) can operate with the 2 MHz timing values defined in this table. 2. Chip Select Input (S) must be brought low for a minimum of tSLSH between consecutive instruction cycles. 3. tCHCL + tCLCH 1 / fC. DocID4997 Rev 15 23/33 32 DC and AC parameters M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Table 17. AC characteristics (M93Cx6-R)(1) Test conditions specified in Table 9 and Table 12 Symbol Alt. fC fSK tSLCH Parameter Min. Max. Unit Clock frequency D.C. 1 MHz Chip Select low to Clock high 250 - ns tSHCH tCSS Chip Select setup time 50 - ns tSLSH(2) tCS Chip Select low to Chip Select high 250 - ns tCHCL (3) tSKH Clock high time 250 - ns tCLCH (3) tSKL Clock low time 250 - ns tDVCH tDIS Data in setup time 100 - ns tCHDX tDIH Data in hold time 100 - ns tCLSH tSKS Clock setup time (relative to S) 100 - ns tCLSL tCSH Chip Select hold time 0 - ns tSHQV tSV Chip Select to READY/BUSY status - 400 ns tSLQZ tDF Chip Select low to output Hi-Z - 200 ns tCHQL tPD0 Delay to output low - 400 ns tCHQV tPD1 Delay to output valid - 400 ns tW tWP Erase or Write cycle time - 10 ms 1. The new M93Cx6-R devices identified with the process letter K can operate with a clock frequency of 2 MHz and an Erase (or Write) cycle of 5 ms, as shown in Table 16. 2. Chip Select Input (S) must be brought low for a minimum of tSLSH between consecutive instruction cycles. 3. tCHCL + tCLCH 1 / fC. 24/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x DC and AC parameters Figure 10. Synchronous timing (Start and op-code input) tCLSH tCHCL C tSHCH tCLCH S tDVCH tCHDX OP CODE START D START OP CODE OP CODE INPUT ai01428 Figure 11. Synchronous timing (Read) C tCLSL S tDVCH D tCHDX tCHQV tSLSH A0 An tSLQZ tCHQL Hi-Z Q Q15/Q7 ADDRESS INPUT Q0 DATA OUTPUT AI00820C Figure 12. Synchronous timing (Write) tSLCH C tCLSL S tDVCH D tCHDX tSLSH A0/D0 An tSHQV tSLQZ Hi-Z Q BUSY READY tW ADDRESS/DATA INPUT WRITE CYCLE ai01429 DocID4997 Rev 15 25/33 32 Package mechanical data 11 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark . Figure 13. PDIP8 – 8 lead plastic dual in-line package, 300 mils body width, package outline E b2 A2 A1 b A L c e eA eB D 8 E1 1 PDIP-B 1. Drawing is not to scale. Table 18. PDIP8 – 8 lead plastic dual in-line package, 300 mils body width, package mechanical data inches(1) millimeters Symbol Typ. Min. Max. Typ. Min. Max. A - - 5.33 - - 0.2098 A1 - 0.38 - - 0.015 - A2 3.3 2.92 4.95 0.1299 0.115 0.1949 b 0.46 0.36 0.56 0.0181 0.0142 0.022 b2 1.52 1.14 1.78 0.0598 0.0449 0.0701 c 0.25 0.2 0.36 0.0098 0.0079 0.0142 D 9.27 9.02 10.16 0.365 0.3551 0.4 E 7.87 7.62 8.26 0.3098 0.3 0.3252 E1 6.35 6.1 7.11 0.25 0.2402 0.2799 e 2.54 - - 0.1 - - eA 7.62 - - 0.3 - - eB - - 10.92 - - 0.4299 L 3.3 2.92 3.81 0.1299 0.115 0.15 1. Values in inches are converted from mm and rounded to 4 decimal digits. 26/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Package mechanical data Figure 14. SO8 narrow – 8 lead plastic small outline, 150 mils body width, package outline h x 45° A2 A c ccc b e 0.25 mm GAUGE PLANE D k 8 E1 E 1 L A1 L1 SO-A 1. Drawing is not to scale. Table 19. SO8 narrow – 8 lead plastic small outline, 150 mils body width, package data inches(1) millimeters Symbol Typ Min Max Typ Min Max A - - 1.75 - - 0.0689 A1 - 0.1 0.25 - 0.0039 0.0098 A2 - 1.25 - - 0.0492 - b - 0.28 0.48 - 0.011 0.0189 c - 0.17 0.23 - 0.0067 0.0091 ccc - - 0.1 - - 0.0039 D 4.9 4.8 5 0.1929 0.189 0.1969 E 6 5.8 6.2 0.2362 0.2283 0.2441 E1 3.9 3.8 4 0.1535 0.1496 0.1575 e 1.27 - - 0.05 - - h - 0.25 0.5 - 0.0098 0.0197 k - 0° 8° - 0° 8° L - 0.4 1.27 - 0.0157 0.05 L1 1.04 - - 0.0409 - - 1. Values in inches are converted from mm and rounded to 4 decimal digits. DocID4997 Rev 15 27/33 32 Package mechanical data M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Figure 15. UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2 x 3 mm, outline D e MC b L1 L3 Pin 1 E E2 K L A D2 eee A1 ZW_MEeV2 1. Drawing is not to scale. 2. The central pad (area E2 by D2 in the above illustration) is pulled, internally, to VSS. It must not be allowed to be connected to any other voltage or signal line on the PCB, for example during the soldering process. 3. The circle in the top view of the package indicates the position of pin 1. Table 20. UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead x 3 mm, data inches(1) millimeters Symbol Typ Min Max Typ Min Max A 0.550 0.450 0.600 0.0217 0.0177 0.0236 A1 0.020 0.000 0.050 0.0008 0.0000 0.0020 b 0.250 0.200 0.300 0.0098 0.0079 0.0118 D 2.000 1.900 2.100 0.0787 0.0748 0.0827 D2 (rev MC) - 1.200 1.600 - 0.0472 0.0630 E 3.000 2.900 3.100 0.1181 0.1142 0.1220 E2 (rev MC) - 1.200 1.600 - 0.0472 0.0630 e 0.500 - - 0.0197 - - K (rev MC) - 0.300 - - 0.0118 - L - 0.300 0.500 - 0.0118 0.0197 L1 - - 0.150 - - 0.0059 L3 - 0.300 - - 0.0118 - - 0.080 - - 0.0031 - eee (2) 1. Values in inches are converted from mm and rounded to four decimal digits. 2. Applied for exposed die paddle and terminals. Exclude embedding part of exposed die paddle from measuring. 28/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Package mechanical data Figure 16. TSSOP8 – 8 lead thin shrink small outline, package outline D 5 8 c E1 E 4 1 a A1 A A2 L L1 CP e b TSSOP8AM 1. Drawing is not to scale. Table 21. TSSOP8 – 8-lead thin shrink small outline, package mechanical data inches(1) millimeters Symbol Typ Min Max Typ Min Max A - - 1.200 - - 0.0472 A1 - 0.050 0.150 - 0.0020 0.0059 A2 1.000 0.800 1.050 0.0394 0.0315 0.0413 b - 0.190 0.300 - 0.0075 0.0118 c - 0.090 0.200 - 0.0035 0.0079 CP - - 0.100 - - 0.0039 D 3.000 2.900 3.100 0.1181 0.1142 0.1220 e 0.650 - - 0.0256 - - E 6.400 6.200 6.600 0.2520 0.2441 0.2598 E1 4.400 4.300 4.500 0.1732 0.1693 0.1772 L 0.600 0.450 0.750 0.0236 0.0177 0.0295 L1 1.000 - - 0.0394 - - - 0° 8° - 0° 8° N 8 8 1. Values in inches are converted from mm and rounded to four decimal digits. DocID4997 Rev 15 29/33 32 Part numbering 12 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Part numbering Table 22. Ordering information scheme Example: M93C86 – W MN 6 T P Device type M93 = MICROWIRE serial EEPROM Device function 86 = 16 Kbit (2048 x 8) 76 = 8 Kbit (1024 x 8) 66 = 4 Kbit (512 x 8) 56 = 2 Kbit (256 x 8) 46 = 1 Kbit (128 x 8) Operating voltage W = VCC = 2.5 to 5.5 V R = VCC = 1.8 to 5.5 V Package BN = PDIP8 MN = SO8 (150 mils width) MC = UFDFPN8 2 x 3 mm (MLP8) DW = TSSOP8 (169 mils width) Device grade 6 = Industrial temperature range, –40 to 85 °C. Device tested with standard test flow Packing blank = standard packing T = tape and reel packing Plating technology P or G = ECOPACK® (RoHS compliant) For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest ST sales office. 30/33 DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x 13 Revision history Revision history Table 23. Document revision history Date Revision Changes 01-Apr-2010 9 Modified footnote in Table 14 and Table 15 on page 23 Updated Figure 14: UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, outline and Table 22: UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data 29-Apr-2010 10 Updated Figure 31: Available M93C66-x products (package, voltage range, temperature grade) UFDFPN option. 12-Apr-2011 11 Updated Table 7: Absolute maximum ratings, MLP8 package data in Section 12: Package mechanical data and process data in Section 9: Clock pulse counter. Deleted Table 29: Available M93C46-x products (package, voltage range, temperature grade), Table 30: Available M93C56-x products (package, voltage range, temperature grade), Table 31: Available M93C66-x products (package, voltage range, temperature grade), Table 32: Available M93C76-x products (package, voltage range, temperature grade) and Table 33: Available M93C86-x products (package, voltage range, temperature grade). 05-Oct-2011 12 Updated Table 1: Device summary and Table 8: Operating conditions (M93Cx6). Modified footnote 2 in Table 7. 13 Document reformatted. Updated: – Part number names – Table 1: Device summary and package figure on cover page – Section 1: Description – Introductory paragraph in Section 9: Maximum ratings – Note (2) under Table 7: Absolute maximum ratings – Table 8: Operating conditions (M93Cx6) and Table 8: Operating conditions (M93Cx6-W) – Introductory paragraph in Section 11: Package mechanical data – Figure 15: UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2 x 3 mm, outline and Table 20: UFDFPN8 8-lead Ultra thin Fine pitch Dual Flat Package No lead 2 x 3 mm, data – Table 22: Ordering information scheme Renamed: – Figure 2: 8-pin package connections (top view) – Table 16: AC characteristics (M93Cx6, device grade 6) Deleted: – Section: Common I/O operation – Table: DC characteristics (M93Cx6, device grade 3), Table: DC characteristics (M93Cx6-W, device grade 3), and Table: AC characteristics (M93Cx6-W, device grade 3) 23-Apr-2013 DocID4997 Rev 15 31/33 32 Revision history M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Table 23. Document revision history (continued) Date 32/33 Revision Changes 26-Oct-2013 14 Updated: – Table 1: Device summary: added “M93C46-R” and “M93C86-R”, deleted M93Cxx part numbers. – Features: Single supply voltage, write cycles and data retention – Section 1: Description – Note (2) under Table 7: Absolute maximum ratings. – Section 10: DC and AC parameters: updated the introduction and deleted tables related to M93Cxx part numbers. – Figure 9: AC testing input output waveforms – Table 14: DC characteristics (M93Cx6-W, device grade 6), Table 15: DC characteristics (M93Cx6-R), Table 16: AC characteristics (M93Cx6-W, M93Cx6-R, device grade 6) and Table 17: AC characteristics (M93Cx6-R). – Table 22: Ordering information scheme. Added: – Figure 4: M93Cx6 ORG input connection – Table 10: Cycling performance and Table 11: Memory cell data retention. 15-Nov-2013 15 Removed Table 14 Cycling performance by byte DocID4997 Rev 15 M93C86-x M93C76-R M93C66-x M93C56-x M93C46-x Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID4997 Rev 15 33/33 33