AFC P o w e r B l o c k M i c r o-M i niat ure Modular S witch in g Po we r Su p p lie s series Single 10 Watt Outputs 3.3VDC to 24VDC Universal 90 to 264VAC Input 3,000VAC Input to Output Isolation -25 to +70°C Operation High Efficiency 2”L x 1”w x 0.9”H Model Number Output Voltage Output Amps Output Watts Size (inches) AFC-3.3S AFC-5S AFC-12S AFC-15S AFC-24S 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC 2.5 2 0.83 0.66 0.42 8W 10W 10W 10W 10W 1 x 2 x 0.9 1 x 2 x 0.9 1 x 2 x 0.9 1 x 2 x 0.9 1 x 2 x 0.9 WWW.ASTRODYNETDI.COM Fully Approved IEC60950 EN60950 UL60950-1 CSA22.2-60950-1 ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 AFC P o w e r B l o c k M i c r o-M i niat ure Modular S witch in g Po we r Su p p lie s INPUT SPECIFICATIONS Input Voltage, Nominal Input Frequency Inrush Current GENERAL SPECIFICATIONS 90-264VAC Nominal: 100-240VAC 47-63 Hz, 50-60Hz Nom. 20A @ 100VAC, typ 40A @ 200VAC, typ OUTPUT SPECIFICATIONS Output Voltage/Current Initial Accuracy Load Regulation 20%-FL Line Regulation Temperature Coefficient Ripple/Noise(20Mhz BW) Overvoltage Protection Hold Up Time Short Circuit Protection OverTemp Protection Current Limit series See Specific Model +/-1%, typ 3.3V & 5V:+/-1%, typ 12V, 15V, & 24V:+/-0.5%, typ 3.3V & 5V:+/-1%, typ 12V, 15V, & 24V:+/-0.5%, typ +/-0.03%/°C 200-250mV Pk-Pk, typ Clamp, 130-150% * 30mS, typ Continuous * Latching, Recovering 130% typ,Self-Reset Foldback Input-Out Isolation Output-Ground Isolation Input-Ground Isolation Operating Frequency Efficiency (@ Full Load) Safety ENVIRONMENTAL SPECIFICATIONS Oper. Temperature Relative Humidity Storage Temperature MTBF may adversely affect long term reliability. Proper operation under conditions other than the standard operating conditions is neither warranteed nor implied. WWW.ASTRODYNETDI.COM -25 to +50°C FL Derate Linearly to 25%L @ 70°C 0-95%, Non-Condensing -25 to +71°C * 466,553 Hrs MIL-HDBK 217, Parts Count Method, 25°C, Ground Benign PHYSICAL SPECIFICATIONS Case Material Construction Weight * These are stress ratings. Exposure of the devices to any of these conditions 3000VAC 1000VAC 2500VAC 100 Khz, fixed, typ 75 - 80%, typ EN60950, TUV File# B050122749064 IEC60950, CB File# DE 3-51024 UL60950-1, UL File# E167432 Rynite, 94V-0 Rated Encapsulated, Soft Pot 1.5 oz (42g) All specifications are typical at nominal input, full load, and 25DegC unless otherwise noted ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458 AFC P o w e r B l o c k M i c r o-M i niat ure Modular S witch in g Po we r Su p p lie s series MECHANICAL SPECIFICATIONS SIDE VIEW BOTTOM VIEW .10 (2.54) .80 (20.32) 1.00 (25.40) ACL -Vout .20 (5.08) MIN. +Vout ACN .10 (2.54) Dim. “H” 1.80 (45.72) .040 (1.016) DIA. .40 (10.16) NOTES: 2.00 (50.80) DIMENSIONS ARE IN INCH (mm) TOLERANCES: .XXX +/-.02(.508) .XX +/-.05(1.27) Dimension “H” 0.9 (22.86) POWER BLOCK APPLICATION NOTES Output Noise EMI C1 = Electrolytic Capacitor Capacitance = 22uF - 220uF Voltage = Two times rated output voltage C1 = 0.22uF X Capacitor L1 = 3uH - 10uH C2, C3 = 220pF Y Capacitors C2 = Electrolytic Capacitor Capacitance = 22uF - 47uF Voltage = Two times rated output voltage Notes: The figure below ia a sample diagram to reduce Output Ripple and Noise. C3 = Ceramic Capacitor Capacitance = 0.01uF - 0.1uF Voltage = 50 volt The figure below ia a suggested diagram to reduce Electromagnetic Interference (EMI). L1 = 10mH - 30mH Common Mode, Choke The diagram above is a recommended circuit, only by trying true application can levels be measured. Inrush Current If desired, the use of a Choke, NTC or Inrush Current Limiter may be used to reduce the Inrush Current Notes: 1. The use of C1 alone may reduce noise to desired levels, if not use L1, C2 and C3 in addition to C1. 2. The figure above is a suggested circuit. Only by trying true application can levels be tested. WWW.ASTRODYNETDI.COM 5214 ASTRODYNE USA: 1-800-823-8082 ASTRODYNE PACIFIC: 886-2-26983458