CANDD IHB100T480512 100 watt triple output half brick dc/dc converter Datasheet

Corporate: www.cdtechno.com
Product: www.cdpowerelectronics.com
IHB100T
100 Watt Triple Output Half Brick DC/DC Converter
33 - 75V Input Range
Each Channel Independently
Current Limited
High Efficiency: 88% Typical
1500VDC Isolation Between
Input and Output
Operation to 100°C Baseplate
Temperature
50µS Transient Recovery,
0-90% Load Step
Primary & Secondary Remote
On/Off
IHB100T Series Approved to
UL/CUL 1950, EN60950
The IHB100T series triple output standard half brick modules are designed
for today’s demanding industrial applications. Available in two wide range
inputs, these isolated converters offer many features in the standard models.
With a complement of safety agency approvals and low noise operations, the
converters respond extremely fast to change in load conditions. Inherent in
the design are very well-controlled output voltage and minimal need for
minimum loading on main (V1) output.
PRODUCT SELECTION CHART
INPUT
VOLTAGE
IHB100T480312
IHB100T480315
IHB100T480512
IHB100T480515
RATED VOUT (VDC)
RATED MAXIMUM I OUT (A)
(VDC)
V1 (±)
V2 (±)
V3 (±)
V1(±)
V2(±)
V3(±)
48 (33-75)
48 (33-75)
48 (33-75)
48 (33-75)
3.3
3.3
5.1
5.0
12
15
12
15
12
15
12
15
30
30
20
20
4.2
3.4
4.2
2.0
4.2
3.4
4.2
2.0
ABSOLUTE MAX.
RATINGS
Output Short-Circuit
Duration
Continuous
Baseplate Temperature
+100°C
Lead Temperature
(soldering, 10 seconds max) +300°C
Storage Temperature
+125°C
Input to Output Isolation
1500 VDC
EFFICIENCY vs TEMPERATURE
TCASE = +40°C, nominal input voltage, nominal load, recommended external
components applied, unless otherwise specified.*
Change in Efficiency (%)
MODEL
Case Temperature (°C)
SPECIFICATIONS, ALL MODELS
Specifications are at TCASE = +40°C nominal input voltage unless otherwise specified.
INPUT
PARAMETER
CONDITIONS
Voltage Range
Reflected Ripple Current
Input Ripple Rejection
Maximum Input Current
GENERAL
IHB100T480312 OUTPUT
Load Regulation
Current Limit Inception
Short-Circuit Current
Transient Response
Peak Deviation
Settling Time
Overvoltage Limit
Efficiency
50
60
VDC
mA
dB
5
6
0.247
A
W
mC
10
20
mA
mA
MIN
Peak Test
1500
1500
500
10
TYP
VISO = 240VAC, 60Hz
2000
180
VIN = Nominal, 50% Load
Within 1% of Nominal VOUT
3.5
MAX
UNITS
VDC
VDC
VDC
MΩ
pF
µA, rms
Open Collector/Drain
VIN = VMAX
1
5
%
mSec
7
0.8
Open Collector
mA
V
100
0.4
Open Collector
µA
V
520
320
47
5
1
KHz
nSec
Ω
V
V
Ω
KHz
oz (g)
Open Collector/Drain
440
150
4
0
470
480
470
TEMPERATURE
Operation/Specification
Storage
Shutdown
Thermal Inpedance
Set Point Voltage
Output Current, IOUT
Output Ripple, p-p
Output Adjust Range
Output Temperature Drift
Line Regulation
UNITS
75
370
CONDITIONS
Any Channel to Any Channel
GENERAL
Set Point Accuracy
Turn-on Time
Remote On/Off Control Inputs
Primary
Sink Current-Logic Low
Vlow
Vhigh
Secondary
Sink Current-Logic Low
Vlow
Vhigh
External Synchronization Input
Frequency
Pulse Width
Source Impedence
Input High Voltage
Input Low Voltage
Input Impedance
Switching Frequency
Weight
Output Power
MAX
48
7.5
15
PARAMETER
PARAMETER
TYP
33
Peak - Peak
DC to 1KHz
Output Power = 100W
VIN = 30V
POUT = 0, VIN, Min<VIN<VIN, Max
No Load Power Dissipation
Inrush Charge
Quiescent Operating Current
Primary On/Off Disabled
Secondary On/Off Disabled
ISOLATION
Input to Each Output
Input to Baseplate
Channel to Channel
Resistance, Input - Output
Capacitance, Input - Output
Leakage Current
MIN
490
3 (85)
Case Temperature
-40
-55
+100
Case to Ambient
CONDITIONS
8.2
V1
Min
Total Combined O/P Power =
100 Watts Max
IO Nom
0.5
DC to 20MHz*
*
°C
°C
°C
°C/W
+100
+125
+115
Max
50
3.3
15
100
100
Other Outputs Min Load
Min
0
V3
Nom
Max
25
12.2
2.1
150
50
Min
Max
25
12.2
2.1
150
50
4.2
500
.02
.05
UNITS
W
V
A
mV
V
%/°C
.02
0.05
0.50
0.10
1.00
1.0
2.0
See Regulation Curves
1.0
2.0
See Regulation Curves
%
%
38
30
38
6.0
5.0
6.0
5.0
A
A
.02
4.2
0
500
Dependent on V1
.05
Nom
30.0
200
3.80
.05
3.15
VIN, Min≤VIN≤VIN, Max
IO = IO, Nom
Min Load to Rated Load
V2
Nom
6.0
6.0
50 to 100% Load Step
150
35
VOUT, 1% of VOUT, Nom
IOUT1=15A, (IOUT2+IOUT3)= 4.2A
F.L. VIN=Nominal
4.2
85
250
50
5.0
86
mV
µSec
V
%
* See Application Notes available on the web at www.cdpowerelectronics.com
Product: www.cdpowerelectronics.com
IHB100T
REV A
10/01
2
SPECIFICATIONS, ALL MODELS
Specifications are at TCASE = +40°C nominal input voltage unless otherwise specified.
PARAMETER
IHB100T480315 OUTPUT
Output Power
Set Point Voltage
Output Current, IOUT
Output Ripple, p-p
Output Adjust Range
Output Temperature Drift
Line Regulation
Load Regulation
Current Limit Inception
Short-Circuit Current
Transient Response
Peak Deviation
Settling Time
Overvoltage Limit
Efficiency
PARAMETER
IHB100T480512 OUTPUT
Output Power
Output Ripple, p-p
Output Adjust Range
Output Temperature Drift
Line Regulation
Load Regulation
Current Limit Inception
Short-Circuit Current
Transient Response
Peak Deviation
Settling Time
Overvoltage Limit
Efficiency
Output Power
0.5
DC to 20MHz*
*
Output Temperature Drift
Line Regulation
Load Regulation
Current Limit Inception
Short-Circuit Current
Transient Response
Peak Deviation
Settling Time
Overvoltage Limit
Efficiency
V2
Nom
Max
50
3.3
15
100
100
3.15
.02
VIN, Min≤VIN≤VIN, Max
IO = IO, Nom
Min Load to Rated Load
Other Outputs Min Load
30.0
200
3.80
.05
0.05
0.50
38
30
0.10
1.0
150
35
250
50
5.0
38
Min
0
V3
Nom
Max
25
15.85
1.66
125
50
.02
Min
3.33
0
500
Dependent on V1
.05
1.0
2.0
See Regulation Curves
5.0
4.0
5.0
Nom
Max
25
15.85
1.66
125
50
3.33
500
.02
.05
1.0
2.0
See Regulation Curves
5.0
4.0
5.0
UNITS
W
V
A
mV
V
%/°C
%
%
A
A
50 to 100% Load Step
VOUT, 1% of VOUT, Nom
IOUT1=15A, (IOUT2+IOUT3) = 3.4A
F.L. VIN=Nominal
CONDITIONS
4.2
85
86
Min
Nom
Max
50
0.5
5.1
10
IO Nom
DC to 20MHz*
*
mV
µSec
V
%
V1
Total Combined O/P Power =
100 Watts Combined
V2
Min
Nom
100
25
20
0
12
2.1
V3
Min
Nom
Max
UNITS
50
25
50
W
4.2
0
12
2.1
4.2
V
A
150
500
mV
V
.02
.05
%/°C
1.0
2.0
%
%
Max
100
150
5.50
150
.02
.05
.02
.05
IO = IO, Nom
Min Load to Rated Load
0.05
0.50
0.10
1.0
1.0
2.0
Other Outputs Min Load
26.0
20.0
26.0
200
300
mV
35
50
7.0
µSec
V
%
4.75
500
Dependent on V1
VIN, Min≤VIN≤VIN, Max
See Regulation Curves
6.0
5.0
6.0
See Regulation Curves
6.0
5.0
6.0
A
A
50 to 100% Load Step
VOUT, 1% of VOUT, Nom
IOUT1=10A, (IOUT2+IOUT3) = 4.2A
F.L. VIN=Nominal
CONDITIONS
6.0
86
87
Min
Nom
Max
50
0.5
5.0
10
V1
Total Combined O/P Power =
100 Watts Max
Set Point Voltage
Output Current, IOUT
Output Ripple, p-p
Output Adjust Range
V1
Min
Total Combined O/P Power =
100 Watts Maximum
IO Nom
Set Point Voltage
Output Current, IOUT
PARAMETER
IHB100T480515 OUTPUT
CONDITIONS
IO Nom
DC to 20MHz*
*
V2
Min
Nom
100
25
20
0
15.3
1.66
V3
Min
Nom
Max
UNITS
50
25
50
W
3.33
0
15.3
1.66
3.33
V
A
125
500
mV
V
.02
.05
%/°C
Max
100
150
5.50
125
.02
.05
.02
IO = IO, Nom
Min Load to Rated Load
0.05
0.05
1.0
1.0
1.0
2.0
See Regulation Curves
1.0
2.0
See Regulation Curves
%
%
Other Outputs Min Load
26.0
20.0
26.0
5.0
4.0
5.0
4.0
A
A
200
300
mV
35
50
7.0
µSec
V
%
4.60
500
Dependent on V1
.05
VIN, Min≤VIN≤VIN, Max
5.0
5.0
50 to 100% Load Step
VOUT, 1% of VOUT, Nom
IOUT1=10A, (IOUT2+IOUT3) = 4.2A
F.L. VIN=Nominal
6.0
86
87
* See Application Notes available on the web at www.cdpowerelectronics.com
Product: www.cdpowerelectronics.com
IHB100T
REV A
10/01
3
MECHANICAL
SIDE VIEW
PIN SIDE
DOWN
PIN CONNECTIONS
1
2
3
4
5
6
7
8
9
10
11
12
PIN SIDE UP
PRIMARY ON/OFF
-VIN
+VIN
SYNC IN
-V2
+V2
TRIM
+V1
-V1
SECONDARY ON/OFF
+V3
-V3
NOTES:
All dimensions are in inches (millimeters).
PIN PLACEMENT TOLERANCE: ± 0.005"
MECHANICAL TOLERANCE: ± 0.015"
Marked with: specific model ordered, date code, job code.
MATERIAL: Units are encapsulated in a low thermal resistance molding
compound which has excellent chemical resistance and electrical
properties in high humidity environments and over a wide operating
temperature range. The encapsulant and outer shell of the unit have
UL94V-0 ratings. Lead material is solder plated to allow ease of
solderability.
C&D Technologies (Power Electronics) Ltd.
Shannon, Co. Clare, Ireland
Tel: +353.61.474.133 Fax:+353.61.474.141
Power Electronics Division, United States
3400 E Britannia Drive, Tucson, Arizona 85706
Tel: 800.547.2537 Fax: 520.770.9369
C&D Technologies, (NCL)
Milton Keynes MK14 5BU UK
Tel: +44 (0)1908 615232 Fax: +44 (0)1908 617545
Any data, prices, descriptions or specifications presented herein are subject to revision by C&D Technologies, Inc. without notice. While such information is believed to be
accurate as indicated herein, C&D Technologies, Inc. makes no warranty and hereby disclaims all warranties, express or implied, with regard to the accuracy or
completeness of such information. Further, because the product(s) featured herein may be used under conditions beyond its control, C&D Technologies, Inc. hereby
disclaims all warranties, either express or implied, concerning the fitness or suitability of such product(s) for any particular use or in any specific application or arising from
any course of dealing or usage of trade. The user is solely responsible for determining the suitability of the product(s) featured herein for user’s intended purpose and in
user’s specific application. C&D Technologies, Inc. does not warrant or recommend that any of its products be used in any life support or aviation or aerospace applications.
Product: www.cdpowerelectronics.com
IHB100T
REV A
10/01
4
Similar pages