SAW Bandpass Filter F4602 Features RF bandpass filter High attenuation No matching 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package RoHS Compliant Package Dimensions 3.80± 0.15 1.00± 0.15 1.50± 0.10 8 3.80± 0.15 1 2 8 7 ITF 4602 3 0.60± 0.10 6 5 1.00± 0.10 7 1 6 2 5 3 4 1.27± 0.10 4 1.40± 0.15 Dimensions shown are nominal in millimeters Pin Configurations Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 2 Input 6 Output 1, 3, 4, 5, 7, 8 Case ground Maximum Ratings Parameter Unit Minimum Typical Maximum Operating Temperature Range °C -30 25 60 Storage Temperature Range °C -40 25 85 Power Handling Capability dBm - - 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 1/7 SAW Bandpass Filter F4602 Specifications Fc = 460 MHz Minimum Typical Maximum Unit Center Frequency ( Fc ) - 460 - MHz Insertion Loss (450 ~ 470 MHz) - 2.6 3.2 dB Amplitude Ripple (450 ~ 470 MHz) - 1.2 2.4 dBp-p Return Loss (450 ~ 470 MHz) 7 8.2 - dB 0.3 ~ 300 MHz 30 58 - 300 ~ 380 MHz 24 56 - 380 ~ 430 MHz 15 54 - 504.825 ~ 524.825 MHz 12 44 - 559.65 ~ 579.65 MHz 28 56 - 669.3 ~ 689.3 MHz 24 54 - 689.3 ~ 1000 MHz 26 44 - Temperature Coefficient of Frequency - -36 - ppm/℃ Input/Output Impedance - 50 - Ohms Relative Attenuation dB Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 2/7 SAW Bandpass Filter F4602 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration ITF 1) 46022) 1) Manufacturer name 2) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 3/7 SAW Bandpass Filter F4602 Typical Performance ( at 25℃ ℃ ) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 4/7 SAW Bandpass Filter F4602 Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 5/7 SAW Bandpass Filter F4602 Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~ 15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 6/7 SAW Bandpass Filter F4602 Carrier Tape Dimensions [unit : mm] A 4.30 ± 0.1 B 4.30 ± 0.1 C 7.25 ± 0.1 D 1.70 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F4602 Rev. Date 2012-09-12 Rev. NSNI01-AS01 7/7