Cypress CY8C3444PVI-118 Programmable system-on-chip (psocâ®) Datasheet

PSoC® 3: CY8C34 Family
Data Sheet
®
Programmable System-on-Chip (PSoC )
General Description
With its unique array of configurable blocks, PSoC® 3 is a true system level solution providing microcontroller unit (MCU), memory,
analog, and digital peripheral functions in a single chip. The CY8C34 family offers a modern method of signal acquisition, signal
processing, and control with high accuracy, high bandwidth, and high flexibility. Analog capability spans the range from thermocouples
(near DC voltages) to ultrasonic signals. The CY8C34 family can handle dozens of data acquisition channels and analog inputs on
every general-purpose input/output (GPIO) pin. The CY8C34 family isalso a high-performance configurable digital system with some
part numbers including interfaces such as USB, multimaster inter-integrated circuit (I2C), and controller area network (CAN). In
addition to communication interfaces, the CY8C34 family has an easy to configure logic array, flexible routing to all I/O pins, and a
high-performance single cycle 8051 microprocessor core. You can easily create system-level designs using a rich library of prebuilt
components and boolean primitives using PSoC Creator™, a hierarchical schematic design entry tool. The CY8C34 family provides
unparalleled opportunities for analog and digital bill of materials integration while easily accommodating last minute design changes
through simple firmware updates.
Features
„ Single cycle 8051 CPU core
DC to 50 MHz operation
Multiply and divide instructions
Flash program memory, up to 64 KB, 100,000 write cycles,
20 years retention, and multiple security features
‡ Up to 8-KB flash error correcting code (ECC) or configuration
storage
‡ Up to 8 KB SRAM
‡ Up to 2 KB electrically erasable programmable read-only
memory (EEPROM), 1 M cycles, and 20 years retention
‡ 24-channel direct memory access (DMA) with multilayer
AHB[1] bus access
• Programmable chained descriptors and priorities
• High bandwidth 32-bit transfer support
„ Low voltage, ultra low-power
‡ Wide operating voltage range: 0.5 V to 5.5 V
‡ High efficiency boost regulator from 0.5-V input through 1.8-V
to 5.0-V output
‡ 0.8 mA at 3 MHz, 1.2 mA at 6 MHz, and 6.6 mA at 50 MHz
‡ Low-power modes including:
• 1-µA sleep mode with real-time clock (RTC) and
low-voltage detect (LVD) interrupt
• 200-nA hibernate mode with RAM retention
„ Versatile I/O system
‡ 28 to 72 I/O (62 GPIOs, eight special input/outputs (SIO),
two USBIOs[2])
‡ Any GPIO to any digital or analog peripheral routability
[2]
‡ LCD direct drive from any GPIO, up to 46×16 segments
®
[3]
‡ CapSense support from any GPIO
‡ 1.2-V to 5.5-V I/O interface voltages, up to four domains
‡ Maskable, independent interrupt request (IRQ) on any pin or
port
‡ Schmitt-trigger transistor-transistor logic (TTL) inputs
‡ All GPIOs configurable as open drain high/low,
pull-up/pull-down, High Z, or strong output
‡ Configurable GPIO pin state at power-on reset (POR)
‡ 25 mA sink on SIO
„ Digital peripherals
‡ 16 to 24 programmable logic device (PLD) based universal
digital blocks (UDB)
[2]
‡ Full CAN 2.0b 16-receive (Rx), 8-transmit (Tx) buffers
[2]
‡ Full-speed (FS) USB 2.0 12 Mbps using internal oscillator
‡ Up to four 16-bit configurable timer, counter, and PWM blocks
‡
‡
‡
Library of standard peripherals
• 8-, 16-, 24-, and 32-bit timers, counters, and PWMs
• Serial peripheral interface (SPI), universal asynchronous
transmitter receiver (UART), I2C
• Many others available in catalog
‡ Library of advanced peripherals
• Cyclic redundancy check (CRC)
• Pseudo random sequence (PRS) generator
• Local interconnect network (LIN) bus 2.0
• Quadrature decoder
„ Analog peripherals (1.71 V ≤ VDDA ≤ 5.5 V)
‡ 1.024 V±0.9-percent internal voltage reference across –40 °C
to +85 °C (14 ppm/°C)
‡ Configurable delta-sigma ADC with 8- to12-bit resolution
• Programmable gain stage: ×0.25 to ×16
• 12-bit mode, 192-ksps, 66-dB signal to noise and distortion
ratio (SINAD), ±1-bit INL/DNL
‡ Two 8-bit, 8-Msps IDACs or 1-Msps VDACs
‡ Four comparators with 95-ns response time
‡ Two uncommitted opamps with 25-mA drive capability
‡ Two configurable multifunction analog blocks. Example
configurations are programmable gain amplifier (PGA),
transimpedance amplifier (TIA), mixer, and sample and hold
‡ CapSense support
„ Programming, debug, and trace
‡ JTAG (4-wire), serial wire debug (SWD) (2-wire), and single
wire viewer (SWV) interfaces
‡ Eight address and one data breakpoint
‡ 4-KB instruction trace buffer
2
‡ Bootloader programming supportable through I C, SPI,
UART, USB, and other interfaces
„ Precision, programmable clocking
‡ 3- to 24-MHz internal oscillator over full temperature and
voltage range
‡ 4- to 25-MHz crystal oscillator for crystal PPM accuracy
‡ Internal PLL clock generation up to 50 MHz
‡ 32.768-kHz watch crystal oscillator
‡ Low-power internal oscillator at 1, 33, and 100 kHz
„ Temperature and packaging
‡ –40 °C to +85 °C degrees industrial temperature
‡ 48-pin SSOP, 48-pin QFN, 68-pin QFN, and 100-pin TQFP
package options
‡
Notes
1. AHB – AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM data transfer bus
2. This feature on select devices only. See Ordering Information on page 113 for details.
3. GPIOs with opamp outputs are not recommended for use with CapSense.
Cypress Semiconductor Corporation
Document Number: 001-53304 Rev. *K
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 30, 2011
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Contents
1. Architectural Overview ..................................................... 3
2. Pinouts ............................................................................... 5
3. Pin Descriptions .............................................................. 10
4. CPU ................................................................................... 11
4.1 8051 CPU ................................................................. 11
4.2 Addressing Modes .................................................... 11
4.3 Instruction Set .......................................................... 12
4.4 DMA and PHUB ....................................................... 16
4.5 Interrupt Controller ................................................... 17
5. Memory ............................................................................. 21
5.1 Static RAM ............................................................... 21
5.2 Flash Program Memory ............................................ 21
5.3 Flash Security ........................................................... 21
5.4 EEPROM .................................................................. 21
5.5 Nonvolatile Latches (NVLs) ...................................... 22
5.6 External Memory Interface ....................................... 23
5.7 Memory Map ............................................................ 23
6. System Integration .......................................................... 25
6.1 Clocking System ....................................................... 25
6.2 Power System .......................................................... 28
6.3 Reset ........................................................................ 31
6.4 I/O System and Routing ........................................... 32
7. Digital Subsystem ........................................................... 38
7.1 Example Peripherals ................................................ 39
7.2 Universal Digital Block .............................................. 42
7.3 UDB Array Description ............................................. 45
7.4 DSI Routing Interface Description ............................ 46
7.5 CAN .......................................................................... 47
7.6 USB .......................................................................... 49
7.7 Timers, Counters, and PWMs .................................. 49
7.8 I2C ............................................................................ 49
8. Analog Subsystem .......................................................... 50
8.1 Analog Routing ......................................................... 52
8.2 Delta-sigma ADC ...................................................... 54
8.3 Comparators ............................................................. 55
8.4 Opamps .................................................................... 56
8.5 Programmable SC/CT Blocks .................................. 56
8.6 LCD Direct Drive ...................................................... 58
Document Number: 001-53304 Rev. *K
8.7 CapSense ................................................................. 59
8.8 Temp Sensor ............................................................ 59
8.9 DAC .......................................................................... 59
8.10 Up/Down Mixer ....................................................... 59
8.11 Sample and Hold .................................................... 60
9. Programming, Debug Interfaces, Resources ................ 60
9.1 JTAG Interface ......................................................... 61
9.2 Serial Wire Debug Interface ..................................... 61
9.3 Debug Features ........................................................ 61
9.4 Trace Features ......................................................... 61
9.5 Single Wire Viewer Interface .................................... 61
9.6 Programming Features ............................................. 61
9.7 Device Security ........................................................ 61
10. Development Support ................................................... 62
10.1 Documentation ....................................................... 62
10.2 Online ..................................................................... 62
10.3 Tools ....................................................................... 62
11. Electrical Specifications ............................................... 63
11.1 Absolute Maximum Ratings .................................... 63
11.2 Device Level Specifications .................................... 64
11.3 Power Regulators ................................................... 68
11.1 Inputs and Outputs ................................................. 72
11.2 Analog Peripherals ................................................. 80
11.3 Digital Peripherals .................................................. 97
11.4 Memory ................................................................ 100
11.5 PSoC System Resources ..................................... 106
11.6 Clocking ................................................................ 109
12. Ordering Information ................................................... 113
12.1 Part Numbering Conventions ............................... 115
13. Packaging ..................................................................... 116
14. Acronyms ..................................................................... 119
15. Reference Documents ................................................. 121
16. Document Conventions .............................................. 121
16.1 Units of Measure .................................................. 121
17. Revision History .......................................................... 122
18. Sales, Solutions, and Legal Information ................... 126
Page 2 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
1. Architectural Overview
Introducing the CY8C34 family of ultra low-power, flash Programmable System-on-Chip (PSoC®) devices, part of a scalable
8-bit PSoC 3 and 32-bit PSoC 5 platform. The CY8C34 family provides configurable blocks of analog, digital, and interconnect circuitry
around a CPU subsystem. The combination of a CPU with a flexible analog subsystem, digital subsystem, routing, and I/O enables
a high level of integration in a wide variety of consumer, industrial, and medical applications.
Figure 1-1. Simplified Block Diagram
Analog Interconnect
Quadrature Decoder
UDB
Sequencer
Usage Example for UDB
IMO
Universal Digital Block Array ( 24 x UDB)
8- Bit
Timer
UDB
UDB
UDB
16- Bit
PWM
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
Master/
Slave
22 Ω
12- Bit SPI
UDB
UDB
UDB
UDB
8- Bit
Timer
Logic
UDB
8- Bit SPI
I2C Slave
UDB
I2C
CAN
2.0
16- Bit PRS
UDB
UDB
FS USB
2.0
4x
Timer
Counter
PWM
Logic
UDB
UART
UDB
USB
PHY
GPIOs
GPIOs
Clock Tree
32.768 KHz
( Optional)
Digital System
System Wide
Resources
Xtal
Osc
SIO
4- 25 MHz
( Optional)
GPIOs
Digital Interconnect
12- Bit PWM
RTC
Timer
System Bus
GPIOs
Memory System
EEPROM
EMIF
SRAM
CPU System
8051 or
Cortex M3
CPU
Interrupt
Controller
Program &
Debug
Program
GPIOs
WDT
and
Wake
Debug &
Trace
PHUB
DMA
FLASH
ILO
Boundary
Scan
Power Management
System
Analog System
LCD Direct
Drive
ADC
POR and
LVD
1.8V LDO
SMP
+
2x
Opamp
-
2 x SC/ CT Blocks
(TIA, PGA, Mixer etc)
3 per
Opamp
Del Sig
Temperature
Sensor
CapSense
ADC
2x DAC
+
4x
CMP
-
GPIOs
1.71 to
5.5V
Sleep
Power
GPIOs
SIOs
Clocking System
0. 5 to 5.5V
( Optional)
Figure 1-1 illustrates the major components of the CY8C34
family. They are:
„ 8051 CPU subsystem
„ Nonvolatile subsystem
„ Programming, debug, and test subsystem
„ Inputs and outputs
„ Clocking
„ Power
„ Digital subsystem
„ Analog subsystem
Document Number: 001-53304 Rev. *K
PSoC’s digital subsystem provides half of its unique
configurability. It connects a digital signal from any peripheral to
any pin through the digital system interconnect (DSI). It also
provides functional flexibility through an array of small, fast, lowpower UDBs. PSoC Creator provides a library of prebuilt and
tested standard digital peripherals (UART, SPI, LIN, PRS, CRC,
timer, counter, PWM, AND, OR, and so on) that are mapped to
the UDB array. You can also easily create a digital circuit using
boolean primitives by means of graphical design entry. Each
UDB contains programmable array logic (PAL)/PLD functionality,
together with a small state machine engine to support a wide
variety of peripherals.
In addition to the flexibility of the UDB array, PSoC also provides
configurable digital blocks targeted at specific functions. For the
Page 3 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
CY8C34 family these blocks can include four 16-bit timer,
counter, and PWM blocks; I2C slave, master, and multi-master;
Full-Speed USB; and Full CAN 2.0b.
For more details on the peripherals see the “Example
Peripherals” section on page 39 of this data sheet. For
information on UDBs, DSI, and other digital blocks, see the
“Digital Subsystem” section on page 38 of this data sheet.
PSoC’s analog subsystem is the second half of its unique
configurability. All analog performance is based on a highly
accurate absolute voltage reference with less than 0.9-percent
error over temperature and voltage. The configurable analog
subsystem includes:
„ Analog muxes
„ Comparators
„ Voltage references
„ Analog-to-digital converter (ADC)
„ Digital-to-analog converters (DACs)
All GPIO pins can route analog signals into and out of the device
using the internal analog bus. This allows the device to interface
up to 62 discrete analog signals. The heart of the analog
subsystem is a fast, accurate, configurable delta-sigma ADC
with these features:
„ Less than 100 µV offset
„ A gain error of 0.2 percent
„ INL less than ±1 LSB
„ DNL less than ±1 LSB
„ SINAD better than 66 dB
This converter addresses a wide variety of precision analog
applications, including some of the most demanding sensors.
Two high-speed voltage or current DACs support 8-bit output
signals at update rate of 8 Msps in current DAC (IDAC) and
1 Msps in voltage DAC (VDAC). They can be routed out of any
GPIO pin. You can create higher resolution voltage PWM DAC
outputs using the UDB array. This can be used to create a pulse
width modulated (PWM) DAC of up to 10 bits, at up to 48 kHz.
The digital DACs in each UDB support PWM, PRS, or
delta-sigma algorithms with programmable widths.
In addition to the ADC and DACs, the analog subsystem
provides multiple:
„ Uncommitted opamps
„ Configurable switched capacitor/continuous time (SC/CT)
blocks. These support:
‡ Transimpedance amplifiers
‡ Programmable gain amplifiers
‡ Mixers
‡ Other similar analog components
See the “Analog Subsystem” section on page 50 of this data
sheet for more details.
PSoC’s 8051 CPU subsystem is built around a single cycle
pipelined 8051 8-bit processor running at up to 50 MHz. The
CPU subsystem includes a programmable nested vector
interrupt controller, DMA controller, and RAM. PSoC’s nested
vector interrupt controller provides low latency by allowing the
CPU to vector directly to the first address of the interrupt service
routine, bypassing the jump instruction required by other
architectures. The DMA controller enables peripherals to
exchange data without CPU involvement. This allows the CPU
to run slower (saving power) or use those CPU cycles to improve
the performance of firmware algorithms. The single cycle 8051
CPU runs ten times faster than a standard 8051 processor. The
processor speed itself is configurable, allowing you to tune active
power consumption for specific applications.
PSoC’s nonvolatile subsystem consists of flash, byte-writeable
EEPROM, and nonvolatile configuration options. It provides up
to 64 KB of on-chip flash. The CPU can reprogram individual
blocks of flash, enabling bootloaders. You can enable an error
correcting code (ECC) for high reliability applications. A powerful
and flexible protection model secures the user's sensitive
information, allowing selective memory block locking for read
and write protection. Up to 2 KB of byte-writeable EEPROM is
available on-chip to store application data. Additionally, selected
configuration options such as boot speed and pin drive mode are
stored in nonvolatile memory. This allows settings to activate
immediately after power-on reset (POR).
The three types of PSoC I/O are extremely flexible. All I/Os have
many drive modes that are set at POR. PSoC also provides up
to four I/O voltage domains through the VDDIO pins. Every GPIO
has analog I/O, LCD drive[4], CapSense[5], flexible interrupt
generation, slew rate control, and digital I/O capability. The SIOs
on PSoC allow VOH to be set independently of VDDIO when used
as outputs. When SIOs are in input mode they are high
impedance. This is true even when the device is not powered or
when the pin voltage goes above the supply voltage. This makes
the SIO ideally suited for use on an I2C bus where the PSoC may
not be powered when other devices on the bus are. The SIO pins
also have high current sink capability for applications such as
LED drives. The programmable input threshold feature of the
SIO can be used to make the SIO function as a general purpose
analog comparator. For devices with Full-Speed USB the USB
physical interface is also provided (USBIO). When not using
USB these pins may also be used for limited digital functionality
and device programming. All of the features of the PSoC I/Os are
covered in detail in the “I/O System and Routing” section on
page 32 of this data sheet.
The PSoC device incorporates flexible internal clock generators,
designed for high stability and factory trimmed for high accuracy.
The Internal Main Oscillator (IMO) is the master clock base for
the system, and has 1-percent accuracy at 3 MHz. The IMO can
be configured to run from 3 MHz up to 24 MHz. Multiple clock
derivatives can be generated from the main clock frequency to
meet application needs.
Notes
4. This feature on select devices only. See Ordering Information on page 113 for details.
5. GPIOs with opamp outputs are not recommended for use with CapSense.
Document Number: 001-53304 Rev. *K
Page 4 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The device provides a PLL to generate system clock frequencies
up to 50 MHz from the IMO, external crystal, or external
reference clock. It also contains a separate, very low-power
Internal low-speed oscillator (ILO) for the sleep and watchdog
timers. A 32.768-kHz external watch crystal is also supported for
use in RTC applications. The clocks, together with
programmable clock dividers, provide the flexibility to integrate
most timing requirements.
The CY8C34 family supports a wide supply operating range from
1.71 V to 5.5 V. This allows operation from regulated supplies
such as 1.8 V ± 5 percent, 2.5 V ±10 percent, 3.3 V ± 10 percent,
or 5.0 V ± 10 percent, or directly from a wide range of battery
types. In addition, it provides an integrated high efficiency
synchronous boost converter that can power the device from
supply voltages as low as 0.5 V. This enables the device to be
powered directly from a single battery or solar cell. In addition,
you can use the boost converter to generate other voltages
required by the device, such as a 3.3-V supply for LCD glass
drive. The boost’s output is available on the VBOOST pin, allowing
other devices in the application to be powered from the PSoC.
PSoC supports a wide range of low-power modes. These include
a 200-nA hibernate mode with RAM retention and a 1-µA sleep
mode with RTC. In the second mode the optional 32.768-kHz
watch crystal runs continuously and maintains an accurate RTC.
Power to all major functional blocks, including the programmable
digital and analog peripherals, can be controlled independently
by firmware. This allows low-power background processing
when some peripherals are not in use. This, in turn, provides a
total device current of only 1.2 mA when the CPU is running at
6 MHz, or 0.8 mA running at 3 MHz.
The details of the PSoC power modes are covered in the “Power
System” section on page 28 of this data sheet.
PSoC uses JTAG (4-wire) or SWD (2-wire) interfaces for
programming, debug, and test. The 1-wire SWV may also be
used for ‘printf’ style debugging. By combining SWD and SWV,
you can implement a full debugging interface with just three pins.
Using these standard interfaces enables you to debug or
program the PSoC with a variety of hardware solutions from
Cypress or third party vendors. PSoC supports on-chip break
points and 4 KB instruction and data race memory for debug.
Details of the programming, test, and debugging interfaces are
discussed in the “Programming, Debug Interfaces, Resources”
section on page 60 of this data sheet.
2. Pinouts
The Vddio pin that supplies a particular set of pins is indicated
by the black lines drawn on the pinout diagrams in Figure 2-1
through Figure 2-4. Using the Vddio pins, a single PSoC can
support multiple interface voltage levels, eliminating the need for
off-chip level shifters. Each Vddio may sink up to 100 mA total to
its associated I/O pins and opamps. On the 68-pin and 100-pin
devices each set of Vddio associated pins may sink up to 100
mA. The 48-pin device may sink up to 100 mA total for all Vddio0
plus Vddio2 associated I/O pins and 100 mA total for all Vddio1
plus Vddio3 associated I/O pins.
Figure 2-1. 48-pin SSOP Part Pinout
(SIO) P12[2]
(SIO) P12[3]
(OpAmp2out, GPIO) P0[0]
(OpAmp0out, GPIO) P0[1]
(OpAmp0+, GPIO) P0[2]
(OpAmp0-/Extref0, GPIO) P0[3]
Vddio0
(OpAmp2+, GPIO) P0[4]
(OpAmp2-, GPIO) P0[5]
(IDAC0, GPIO) P0[6]
(IDAC2, GPIO) P0[7]
Vccd
Vssd
Vddd
(GPIO) P2[3]
(GPIO) P2[4]
Vddio2
(GPIO) P2[5]
(GPIO) P2[6]
(GPIO) P2[7]
Vssb
Ind
Vboost
Vbat
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Lines show
Vddio to I/O
supply
association
SSOP
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Vdda
Vssa
Vcca
P15[3] (GPIO, kHz XTAL: Xi)
P15[2] (GPIO, kHz XTAL: Xo)
P12[1] (SIO, I2C1: SDA)
P12[0] (SIO, I2C1: SCL)
Vddio3
P15[1] (GPIO, MHz XTAL: Xi)
P15[0] (GPIO, MHz XTAL: Xo)
Vccd
Vssd
Vddd
[6]
P15[7] (USBIO, D-, SWDCK)
[6]
P15[6] (USBIO, D+, SWDIO)
P1[7] (GPIO)
P1[6] (GPIO)
Vddio1
P1[5] (GPIO, nTRST)
P1[4] (GPIO, TDI)
P1[3] (GPIO, TDO, SWV)
P1[2] (GPIO, configurable XRES)
P1[1] (GPIO, TCK, SWDCK)
P1[0] (GPIO, TMS, SWDIO)
Note
6. Pins are Do Not Use (DNU) on devices without USB. The pin must be left floating.
Document Number: 001-53304 Rev. *K
Page 5 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
48
47
46
45
44
43
42
41
40
39
38
37
P2[5] (GPIO)
Vddio2
P2[4] (GPIO)
P2[3] (GPIO)
Vddd
Vssd
Vccd
P0[7] (IDAC2, GPIO)
P0[6] (IDAC0, GPIO)
P0[5] (OpAmp2-, GPIO)
P0[4] (OpAmp2+, GPIO)
Vddio0
Figure 2-2. 48-pin QFN Part Pinout[8]
(GPIO) P2[6]
(GPIO) P2[7]
1
2
Vssb
Ind
Vboost
Vbat
(GPIO, TMS, SWDIO) P1[0]
(GPIO, TCK, SWDCK) P1[1]
(GPIO, Configurable XRES) P1[2]
(GPIO, TDO, SWV) P1[3]
(GPIO, TDI) P1[4]
(GPIO, nTRST) P1[5]
3
4
5
6
QFN
( Top View)
36
35
34
33
32
31
30
29
28
27
26
25
P0[3] (OpAmp0-/Extref0, GPIO)
P0[2] (OpAmp0+, GPIO)
P0[1] (OpAmp0out, GPIO)
P0[0] (OpAmp2out, GPIO)
P12[3] (SIO)
P12[2] (SIO)
Vdda
Vssa
Vcca
P15[3] (GPIO, kHz XTAL: Xi)
P15[2] (GPIO, kHz XTAL: Xo)
P12[1] (SIO, I2C1: SDA)
Vddio1
(GPIO) P1[6]
(GPIO) P1[7]
[7]
(USBIO, D+, SWDIO) P15[6]
[7]
(USBIO, D-, SWDCK) P15[7]
Vddd
Vssd
Vccd
(GPIO, MHz XTAL: Xo) P15[0]
(GPIO, MHz XTAL: Xi) P15[1]
Vddio3
(SIO, I2C1: SCL) P12[0]
13
14
15
16
17
18
19
20
21
22
23
24
7
8
9
10
11
12
Lines show
Vddio to I/O
supply
association
Notes
7. Pins are Do Not Use (DNU) on devices without USB. The pin must be left floating.
8. The center pad on the QFN package should be connected to digital ground (VSSD) for best mechanical, thermal, and electrical performance. If not connected to ground,
it should be electrically floated and not connected to any other signal.
Document Number: 001-53304 Rev. *K
Page 6 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
55
54
53
52
58
57
56
P15[5] (GPOI)
P15[4] (GPIO)
Vddd
Vssd
Vccd
P0[7] (GPIO, IDAC2)
P0[6] (GPIO, IDAC0)
P0[5] (GPIO, OpAmp2-)
P0[4] (GPIO, OpAmp2+)
Vddio0
51
50
Lines show Vddio
to I/O supply
association
QFN
28
29
30
31
32
33
34
(MHz XTAL: Xi, GPIO) P15[1]
(GPIO) P3[0]
(GPIO) P3[1]
(Extref1, GPIO) P3[2]
(GPIO) P3[3]
(GPIO) P3[4]
(GPIO) P3[5]
(Top View)
18
19
20
21
22
23
24
25
26
27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
(GPIO) P1[6]
(GPIO) P1[7]
(SIO) P12[6]
(SIO) P12[7]
[9]
(USBIO, D+, SWDIO) P15[6]
[9](USBIO, D-, SWDCK) P15[7]
Vddd
Vssd
Vccd
(MHz XTAL: Xo, GPIO) P15[0]
(GPIO) P2[6]
(GPIO) P2[7]
(I2C0: SCL, SIO) P12[4]
(I2C0: SDA, SIO) P12[5]
Vssb
Ind
Vboost
Vbat
Vssd
XRES
(TMS, SWDIO, GPIO) P1[0]
(TCK, SWDCK, GPIO) P1[1]
(configurable XRES, GPIO) P1[2]
(TDO, SWV, GPIO) P1[3]
(TDI, GPIO) P1[4]
(nTRST, GPIO) P1[5]
Vddio1
66
65
64
63
62
61
60
59
68
67
P2[5] (GPIO)
Vddio2
P2[4] (GPIO)
P2[3] (GPIO)
P2[2] (GPIO)
P2[1] (GPIO)
P2[0] (GPIO)
Figure 2-3. 68-Pin QFN Part Pinout[10]
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
P0[3] (GPIO, OpAmp0-/Extref0)
P0[2] (GPIO, OpAmp0+)
P0[1] (GPIO, OpAmp0out)
P0[0] (GPIO, OpAmp2out)
P12[3] (SIO)
P12[2] (SIO)
Vssd
Vdda
Vssa
Vcca
P15[3] (GPIO, kHz XTAL: Xi)
P15[2] (GPIO, kHz XTAL: Xo)
P12[1] (SIO, I2C1: SDA)
P12[0] (SIO, 12C1: SCL)
P3[7] (GPIO)
P3[6] (GPIO)
Vddio3
Notes
9. Pins are Do Not Use (DNU) on devices without USB. The pin must be left floating.
10. The center pad on the QFN package should be connected to digital ground (Vssd) for best mechanical, thermal, and electrical performance. If not connected to ground,
it should be electrically floated and not connected to any other signal.
Document Number: 001-53304 Rev. *K
Page 7 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
TQFP
77
76
P4[5] (GPIO)
P4[4] (GPIO)
P4[3] (GPIO)
P4[2] (GPIO)
P0[7] (GPIO, IDAC2)
P0[6] (GPIO, IDAC0)
P0[5] (GPIO, OpAmp2-)
P0[4] (GPIO, OpAmp2+)
87
86
85
84
83
82
81
80
79
78
90
89
88
P15[4] (GPIO)
P6[3] (GPIO)
P6[2] (GPIO)
P6[1] (GPIO)
P6[0] (GPIO)
Vddd
Vssd
Vccd
P4[7] (GPIO)
P4[6] (GPIO)
98
97
96
95
94
93
92
91
Lines show Vddio
to I/O supply
association
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
Vddio0
P0[3] (GPIO, OpAmp0-/Extref0)
P0[2] (GPIO, OpAmp0+)
P0[1] (GPIO, OpAmp0out)
P0[0] (GPIO, OpAmp2out)
P4[1] (GPIO)
P4[0] (GPIO)
P12[3] (SIO)
P12[2] (SIO)
Vssd
Vdda
Vssa
Vcca
NC
NC
NC
NC
NC
NC
P15[3] (GPIO, kHz XTAL: Xi)
P15[2] (GPIO, kHz XTAL: Xo)
P12[1] (SIO, I2C1: SDA)
P12[0] (SIO, I2C1: SCL)
P3[7] (GPIO)
P3[6] (GPIO)
[11]
(GPIO) P3[5]
Vddio3
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
(USBIO, D-, SWDCK) P15[7]
Vddd
Vssd
Vccd
NC
NC
(MHz XTAL: Xo, GPIO) P15[0]
(MHz XTAL: Xi, GPIO) P15[1]
(GPIO) P3[0]
(GPIO) P3[1]
(Extref1, GPIO) P3[2]
(GPIO) P3[3]
(GPIO) P3[4]
54
53
52
51
26
27
28
29
30
31
32
33
34
35
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Vddio1
(GPIO) P1[6]
(GPIO) P1[7]
(SIO) P12[6]
(SIO) P12[7]
(GPIO) P5[4]
(GPIO) P5[5]
(GPIO) P5[6]
(GPIO) P5[7]
[11]
(USBIO, D+, SWDIO) P15[6]
(GPIO) P2[5]
(GPIO) P2[6]
(GPIO) P2[7]
(I2C0: SCL, SIO) P12[4]
(I2C0: SDA, SIO) P12[5]
(GPIO) P6[4]
(GPIO) P6[5]
(GPIO) P6[6]
(GPIO) P6[7]
Vssb
Ind
Vboost
Vbat
Vssd
XRES
(GPIO) P5[0]
(GPIO) P5[1]
(GPIO) P5[2]
(GPIO) P5[3]
(TMS, SWDIO, GPIO) P1[0]
(TCK, SWDCK, GPIO) P1[1]
(configurable XRES, GPIO) P1[2]
(TDO, SWV, GPIO) P1[3]
(TDI, GPIO) P1[4]
(nTRST, GPIO) P1[5]
100
99
Vddio2
P2[4] (GPIO)
P2[3] (GPIO)
P2[2] (GPIO)
P2[1] (GPIO)
P2[0] (GPIO)
P15[5] (GPIO)
Figure 2-4. 100-pin TQFP Part Pinout
Note
11. Pins are Do Not Use (DNU) on devices without USB. The pin must be left floating.
Document Number: 001-53304 Rev. *K
Page 8 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 2-5 and Figure 2-6 on page 10 show an example schematic and an example PCB layout, for the 100-pin TQFP part, for optimal
analog performance on a two-layer board.
„ The two pins labeled Vddd must be connected together.
„ The two pins labeled Vccd must be connected together, with capacitance added, as shown in Figure 2-5 and Power System on
page 28. The trace between the two Vccd pins should be as short as possible.
„ The two pins labeled Vssd must be connected together.
For information on circuit board layout issues for mixed signals, refer to the application note AN57821 - Mixed Signal Circuit Board
Layout Considerations for PSoC® 3 and PSoC 5.
Figure 2-5. Example Schematic for 100-pin TQFP Part With Power Connections
Vddd
Vddd
C1
1 uF
Vddd
C2
0.1 uF
U2
CY8C55xx
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P2[5]
P2[6]
P2[7]
P12[4], SIO
P12[5], SIO
P6[4]
P6[5]
P6[6]
P6[7]
Vssb
Ind
Vboost
Vbat
Vssd
XRES
P5[0]
P5[1]
P5[2]
P5[3]
P1[0], SWIO, TMS
P1[1], SWDIO, TCK
P1[2]
P1[3], SWV, TDO
P1[4], TDI
P1[5], nTRST
Vdda
Vddd
Vddio0
OA0-, REF0, P0[3]
OA0+, P0[2]
OA0out, P0[1]
OA2out, P0[0]
P4[1]
P4[0]
SIO, P12[3]
SIO, P12[2]
Vssd
Vdda
Vssa
Vcca
NC
NC
NC
NC
NC
NC
kHzXin, P15[3]
kHzXout, P15[2]
SIO, P12[1]
SIO, P12[0]
OA3out, P3[7]
OA1out, P3[6]
Vddio1
P1[6]
P1[7]
P12[6], SIO
P12[7], SIO
P5[4]
P5[5]
P5[6]
P5[7]
USB D+, P15[6]
USB D-, P15[7]
Vddd
Vssd
Vccd
NC
NC
P15[0], MHzXout
P15[1], MHzXin
P3[0], IDAC1
P3[1], IDAC3
P3[2], OA3-, REF1
P3[3], OA3+
P3[4], OA1P3[5], OA1+
Vddio3
Vssd
Vddd
C12
0.1 uF
Vccd
Vddd
Vssd
Vssd
Vssd
C15
1 uF
C16
0.1 uF
C8
0.1 uF
C17
1 uF
Vssd
Vssd
Vssa
Vdda
Vssd
Vdda
Vssa
Vcca
C9
1 uF
C10
0.1 uF
Vssa
C11
0.1 uF
C13
10 uF, 6.3 V
Vssa
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Vddd
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
P32 47
48
49
50
Vssd
Vssd
Vddio2
P2[4]
P2[3]
P2[2]
P2[1]
P2[0]
P15[5]
P15[4]
P6[3]
P6[2]
P6[1]
P6[0]
Vddd
Vssd
Vccd
P4[7]
P4[6]
P4[5]
P4[4]
P4[3]
P4[2]
IDAC2, P0[7]
IDAC0, P0[6]
OA2-, P0[5]
OA2+, P0[4]
Vssd
Vddd
100
99
98
97
96
95
94
93
92
91
90
89
Vddd
88
Vssd
87
86
85
84
83
82
81
80
79
78
77
76
Vccd
C6
0.1 uF
C14
0.1 uF Vssd
Vssa
Vssd
Note The two Vccd pins must be connected together with as short a trace as possible. A trace under the device is recommended, as
shown in Figure 2-6 on page 10.
Document Number: 001-53304 Rev. *K
Page 9 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 2-6. Example PCB Layout for 100-pin TQFP Part for Optimal Analog Performance
Vssa
Vddd
Vssd
Vdda
Vssa
Plane
Vssd
Plane
3. Pin Descriptions
IDAC0, IDAC2
Low resistance output pin for high current DACs (IDAC).
OpAmp0out, OpAmp2out
High current output of uncommitted opamp[12].
Extref0, Extref1
MHz XTAL: Xo, MHz XTAL: Xi
4- to 25-MHz crystal oscillator pin.
nTRST
Optional JTAG test reset programming and debug port
connection to reset the JTAG connection.
SIO
OpAmp0–, OpAmp2–
Special I/O provides interfaces to the CPU, digital peripherals
and interrupts with a programmable high threshold voltage,
analog comparator, high sink current, and high impedance state
when the device is unpowered.
Inverting input to uncommitted opamp.
SWDCK
OpAmp0+, OpAmp2+
Noninverting input to uncommitted opamp.
Serial wire debug clock programming and debug port
connection.
GPIO
SWDIO
General purpose I/O pin provides interfaces to the CPU, digital
peripherals, analog peripherals, interrupts, LCD segment drive,
and CapSense[12].
Serial wire debug input and output programming and debug port
connection.
I2C0: SCL, I2C1: SCL
Single wire viewer debug output.
External reference input to the analog system.
I2C SCL line providing wake from sleep on an address match.
Any I/O pin can be used for I2C SCL if wake from sleep is not
required.
SWV.
TCK
JTAG test clock programming and debug port connection.
I2C0: SDA, I2C1: SDA
TDI
I2C
JTAG test data In programming and debug port connection.
SDA line providing wake from sleep on an address match.
Any I/O pin can be used for I2C SDA if wake from sleep is not
required.
Ind
Inductor connection to boost pump.
kHz XTAL: Xo, kHz XTAL: Xi
TDO
JTAG test data out programming and debug port connection.
TMS
JTAG test mode select programming and debug port connection.
32.768-kHz crystal oscillator pin.
Note
12. GPIOs with opamp outputs are not recommended for use with CapSense.
Document Number: 001-53304 Rev. *K
Page 10 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
USBIO, D+
4. CPU
Provides D+ connection directly to a USB 2.0 bus. May be used
as a digital I/O pin. Pins are Do Not Use (DNU) on devices
without USB.
4.1 8051 CPU
USBIO, D–
Provides D– connection directly to a USB 2.0 bus. May be used
as a digital I/O pin. Pins are No Connect (NC) on devices without
USB.
Vboost
Power sense connection to boost pump.
Vbat
Battery supply to boost pump.
The CY8C34 devices use a single cycle 8051 CPU, which is fully
compatible with the original MCS-51 instruction set. The
CY8C34 family uses a pipelined RISC architecture, which
executes most instructions in 1 to 2 cycles to provide peak
performance of up to 24 MIPS with an average of 2 cycles per
instruction. The single cycle 8051 CPU runs ten times faster than
a standard 8051 processor.
The 8051 CPU subsystem includes these features:
„ Single cycle 8051 CPU
„ Up to 64 KB of flash memory, up to 2 KB of EEPROM, and up
to 8 KB of SRAM
Vcca
„ Programmable nested vector interrupt controller
Output of analog core regulator and input to analog core.
Requires a 1-µF capacitor to VSSA. Regulator output not for
external use.
„ Direct memory access (DMA) controller
Vccd
„ External memory interface (EMIF)
Output of digital core regulator and input to digital core. The two
VCCD pins must be shorted together, with the trace between
them as short as possible, and a 1-µF capacitor to VSSD; see
Power System on page 28. Regulator output not for external use.
4.2 Addressing Modes
Vdda
Supply for all analog peripherals and analog core regulator.
Vdda must be the highest voltage present on the device. All
other supply pins must be less than or equal to Vdda.
Vddd
Supply for all digital peripherals and digital core regulator. Vddd
must be less than or equal to Vdda.
Vssa
Ground for all analog peripherals.
Vssb
Ground connection for boost pump.
Vssd
Ground for all digital logic and I/O pins.
Vddio0, Vddio1, Vddio2, Vddio3
Supply for I/O pins. See pinouts for specific I/O pin to Vddio
mapping. Each Vddio must be tied to a valid operating voltage
(1.71 V to 5.5 V), and must be less than or equal to Vdda. If the
I/O pins associated with Vddio0, Vddio2 or Vddio3 are not used
then that Vddio should be tied to ground (Vssd or Vssa).
„ Peripheral HUB (PHUB)
The following addressing modes are supported by the 8051:
„ Direct Addressing: The operand is specified by a direct 8-bit
address field. Only the internal RAM and the SFRs can be
accessed using this mode.
„ Indirect Addressing: The instruction specifies the register which
contains the address of the operand. The registers R0 or R1
are used to specify the 8-bit address, while the data pointer
(DPTR) register is used to specify the 16-bit address.
„ Register Addressing: Certain instructions access one of the
registers (R0 to R7) in the specified register bank. These
instructions are more efficient because there is no need for an
address field.
„ Register Specific Instructions: Some instructions are specific
to certain registers. For example, some instructions always act
on the accumulator. In this case, there is no need to specify the
operand.
„ Immediate Constants: Some instructions carry the value of the
constants directly instead of an address.
„ Indexed Addressing: This type of addressing can be used only
for a read of the program memory. This mode uses the Data
Pointer as the base and the accumulator value as an offset to
read a program memory.
„ Bit Addressing: In this mode, the operand is one of 256 bits.
XRES (and configurable XRES)
External reset pin. Active low with internal pull-up. Pin P1[2] may
be configured to be a XRES pin; see “Nonvolatile Latches
(NVLs)” on page 22.
Document Number: 001-53304 Rev. *K
Page 11 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
4.3 Instruction Set
4.3.1 Instruction Set Summary
The 8051 instruction set is highly optimized for 8-bit handling and
Boolean operations. The types of instructions supported include:
4.3.1.1 Arithmetic Instructions
„ Arithmetic instructions
„ Logical instructions
„ Data transfer instructions
„ Boolean instructions
Arithmetic instructions support the direct, indirect, register,
immediate constant, and register-specific instructions.
Arithmetic modes are used for addition, subtraction,
multiplication, division, increment, and decrement operations.
Table 4-1 on page 12 Table 4-1 lists the different arithmetic
instructions.
„ Program branching instructions
Table 4-1. Arithmetic Instructions
Mnemonic
Description
Bytes
Cycles
ADD
A,Rn
Add register to accumulator
1
1
ADD
A,Direct
Add direct byte to accumulator
2
2
ADD
A,@Ri
Add indirect RAM to accumulator
1
2
ADD
A,#data
Add immediate data to accumulator
2
2
ADDC A,Rn
Add register to accumulator with carry
1
1
ADDC A,Direct
Add direct byte to accumulator with carry
2
2
ADDC A,@Ri
Add indirect RAM to accumulator with carry
1
2
ADDC A,#data
Add immediate data to accumulator with carry
2
2
SUBB A,Rn
Subtract register from accumulator with borrow
1
1
SUBB A,Direct
Subtract direct byte from accumulator with borrow
2
2
SUBB A,@Ri
Subtract indirect RAM from accumulator with borrow
1
2
SUBB A,#data
Subtract immediate data from accumulator with borrow
2
2
INC
A
Increment accumulator
1
1
INC
Rn
Increment register
1
2
INC
Direct
Increment direct byte
2
3
INC
@Ri
Increment indirect RAM
1
3
DEC
A
Decrement accumulator
1
1
DEC
Rn
Decrement register
1
2
DEC
Direct
Decrement direct byte
2
3
DEC
@Ri
Decrement indirect RAM
1
3
INC
DPTR
Increment data pointer
1
1
MUL
Multiply accumulator and B
1
2
DIV
Divide accumulator by B
1
6
DAA
Decimal adjust accumulator
1
3
Document Number: 001-53304 Rev. *K
Page 12 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
4.3.1.2 Logical Instructions
The logical instructions perform Boolean operations such as AND, OR, XOR on bytes, rotate of accumulator contents, and swap of
nibbles in an accumulator. The Boolean operations on the bytes are performed on the bit-by-bit basis. Table 4-2 on page 13Table 4-2
shows the list of logical instructions and their description.
Table 4-2. Logical Instructions
Mnemonic
Description
Bytes
Cycles
ANL
A,Rn
AND register to accumulator
1
1
ANL
A,Direct
AND direct byte to accumulator
2
2
ANL
A,@Ri
AND indirect RAM to accumulator
1
2
ANL
A,#data
AND immediate data to accumulator
2
2
ANL
Direct, A
AND accumulator to direct byte
2
3
ANL
Direct, #data
AND immediate data to direct byte
3
3
ORL
A,Rn
OR register to accumulator
1
1
ORL
A,Direct
OR direct byte to accumulator
2
2
ORL
A,@Ri
OR indirect RAM to accumulator
1
2
ORL
A,#data
OR immediate data to accumulator
2
2
ORL
Direct, A
OR accumulator to direct byte
2
3
ORL
Direct, #data
OR immediate data to direct byte
3
3
XRL
A,Rn
XOR register to accumulator
1
1
XRL
A,Direct
XOR direct byte to accumulator
2
2
XRL
A,@Ri
XOR indirect RAM to accumulator
1
2
XRL
A,#data
XOR immediate data to accumulator
2
2
XRL
Direct, A
XOR accumulator to direct byte
2
3
XRL
Direct, #data
XOR immediate data to direct byte
3
3
CLR
A
Clear accumulator
1
1
CPL
A
Complement accumulator
1
1
RL
A
Rotate accumulator left
1
1
RLC
A
Rotate accumulator left through carry
1
1
RR
A
Rotate accumulator right
1
1
RRC A
Rotate accumulator right though carry
1
1
SWAP A
Swap nibbles within accumulator
1
1
Document Number: 001-53304 Rev. *K
Page 13 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
4.3.1.3 Data Transfer Instructions
The data transfer instructions are of three types: the core RAM,
xdata RAM, and the lookup tables. The core RAM transfer
includes transfer between any two core RAM locations or SFRs.
These instructions can use direct, indirect, register, and
immediate addressing. The xdata RAM transfer includes only the
transfer between the accumulator and the xdata RAM location.
It can use only indirect addressing. The lookup tables involve
nothing but the read of program memory using the Indexed
addressing mode. Table 4-3 lists the various data transfer
instructions available.
4.3.1.4 Boolean Instructions
The 8051 core has a separate bit addressable memory location.
It has 128 bits of bit-addressable RAM and a set of SFRs that are
bit addressable. The instruction set includes the whole menu of
bit operations such as move, set, clear, toggle, OR, and AND
instructions and the conditional jump instructions. Table 4-4 on
page 15Table 4-4 lists the available Boolean instructions.
Table 4-3. Data Transfer Instructions
Mnemonic
Description
Bytes
Cycles
MOV
A,Rn
Move register to accumulator
1
1
MOV
A,Direct
Move direct byte to accumulator
2
2
MOV
A,@Ri
Move indirect RAM to accumulator
1
2
MOV
A,#data
Move immediate data to accumulator
2
2
MOV
Rn,A
Move accumulator to register
1
1
MOV
Rn,Direct
Move direct byte to register
2
3
MOV
Rn, #data
Move immediate data to register
2
2
MOV
Direct, A
Move accumulator to direct byte
2
2
MOV
Direct, Rn
Move register to direct byte
2
2
MOV
Direct, Direct
Move direct byte to direct byte
3
3
MOV
Direct, @Ri
Move indirect RAM to direct byte
2
3
MOV
Direct, #data
Move immediate data to direct byte
3
3
MOV
@Ri, A
Move accumulator to indirect RAM
1
2
MOV
@Ri, Direct
Move direct byte to indirect RAM
2
3
MOV
@Ri, #data
Move immediate data to indirect RAM
2
2
MOV
DPTR, #data16
Load data pointer with 16-bit constant
3
3
MOVC A, @A+DPTR
Move code byte relative to DPTR to accumulator
1
5
MOVC A, @A + PC
Move code byte relative to PC to accumulator
1
4
MOVX A,@Ri
Move external RAM (8-bit) to accumulator
1
4
MOVX A, @DPTR
Move external RAM (16-bit) to accumulator
1
3
MOVX @Ri, A
Move accumulator to external RAM (8-bit)
1
5
MOVX @DPTR, A
Move accumulator to external RAM (16-bit)
1
4
PUSH Direct
Push direct byte onto stack
2
3
POP
Direct
Pop direct byte from stack
2
2
XCH
A, Rn
Exchange register with accumulator
1
2
XCH
A, Direct
Exchange direct byte with accumulator
2
3
XCH
A, @Ri
Exchange indirect RAM with accumulator
1
3
Exchange low order indirect digit RAM with accumulator
1
3
XCHD A, @Ri
Document Number: 001-53304 Rev. *K
Page 14 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 4-4. Boolean Instructions
Mnemonic
Description
Bytes
Cycles
CLR
C
Clear carry
1
1
CLR
bit
Clear direct bit
2
3
SETB C
Set carry
1
1
SETB bit
Set direct bit
2
3
CPL
Complement carry
1
1
C
CPL
bit
Complement direct bit
2
3
ANL
C, bit
AND direct bit to carry
2
2
ANL
C, /bit
AND complement of direct bit to carry
2
2
OR direct bit to carry
2
2
ORL C, /bit
OR complement of direct bit to carry
2
2
MOV C, bit
Move direct bit to carry
2
2
MOV bit, C
Move carry to direct bit
2
3
JC
Jump if carry is set
2
3
JNC rel
Jump if no carry is set
2
3
JB
Jump if direct bit is set
3
5
JNB bit, rel
Jump if direct bit is not set
3
5
JBC bit, rel
Jump if direct bit is set and clear bit
3
5
ORL C, bit
rel
bit, rel
4.3.1.5 Program Branching Instructions
The 8051 supports a set of conditional and unconditional jump instructions that help to modify the program execution flow. Table 4-5
shows the list of jump instructions.
Table 4-5. Jump Instructions
Mnemonic
Description
Bytes
Cycles
ACALL addr11
Absolute subroutine call
2
4
LCALL addr16
Long subroutine call
3
4
RET
Return from subroutine
1
4
RETI
Return from interrupt
1
4
AJMP addr11
Absolute jump
2
3
LJMP addr16
Long jump
3
4
SJMP rel
Short jump (relative address)
2
3
JMP @A + DPTR
Jump indirect relative to DPTR
1
5
JZ rel
Jump if accumulator is zero
2
4
JNZ rel
Jump if accumulator is nonzero
2
4
CJNE A,Direct, rel
Compare direct byte to accumulator and jump if not equal
3
5
CJNE A, #data, rel
Compare immediate data to accumulator and jump if not equal
3
4
CJNE Rn, #data, rel
Compare immediate data to register and jump if not equal
3
4
CJNE @Ri, #data, rel
Compare immediate data to indirect RAM and jump if not equal
3
5
DJNZ Rn,rel
Decrement register and jump if not zero
2
4
DJNZ Direct, rel
Decrement direct byte and jump if not zero
3
5
NOP
No operation
1
1
Document Number: 001-53304 Rev. *K
Page 15 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
4.4 DMA and PHUB
„ Any digitally routable signal, the CPU, or another DMA channel,
The PHUB and the DMA controller are responsible for data
transfer between the CPU and peripherals, and also data
transfers between peripherals. The PHUB and DMA also control
device configuration during boot. The PHUB consists of:
„ A central hub that includes the DMA controller, arbiter, and
router
„ Multiple spokes that radiate outward from the hub to most
peripherals
There are two PHUB masters: the CPU and the DMA controller.
Both masters may initiate transactions on the bus. The DMA
channels can handle peripheral communication without CPU
intervention. The arbiter in the central hub determines which
DMA channel is the highest priority if there are multiple requests.
4.4.1 PHUB Features
„ CPU and DMA controller are both bus masters to the PHUB
„ Eight Multi-layer AHB Bus parallel access paths (spokes) for
peripheral access
„ Simultaneous CPU and DMA access to peripherals located on
different spokes
„ Simultaneous DMA source and destination burst transactions
on different spokes
„ Supports 8, 16, 24, and 32-bit addressing and data
Table 4-6. PHUB Spokes and Peripherals
can trigger a transaction
„ Each channel can generate up to two interrupts per transfer
„ Transactions can be stalled or canceled
„ Supports transaction size of infinite or 1 to 64 KB
„ TDs may be nested and/or chained for complex transactions
4.4.3 Priority Levels
The CPU always has higher priority than the DMA controller
when their accesses require the same bus resources. Due to the
system architecture, the CPU can never starve the DMA. DMA
channels of higher priority (lower priority number) may interrupt
current DMA transfers. In the case of an interrupt, the current
transfer is allowed to complete its current transaction. To ensure
latency limits when multiple DMA accesses are requested
simultaneously, a fairness algorithm guarantees an interleaved
minimum percentage of bus bandwidth for priority levels 2
through 7. Priority levels 0 and 1 do not take part in the fairness
algorithm and may use 100 percent of the bus bandwidth. If a tie
occurs on two DMA requests of the same priority level, a simple
round robin method is used to evenly share the allocated
bandwidth. The round robin allocation can be disabled for each
DMA channel, allowing it to always be at the head of the line.
Priority levels 2 to 7 are guaranteed the minimum bus bandwidth
shown in Table 4-7 after the CPU and DMA priority levels 0 and
1 have satisfied their requirements.
Table 4-7. Priority Levels
Priority Level
% Bus Bandwidth
SRAM
0
100.0
1
IOs, PICU, EMIF
1
100.0
2
PHUB local configuration, Power manager,
Clocks, IC, SWV, EEPROM, Flash
programming interface
2
50.0
3
25.0
4
12.5
5
6.2
6
3.1
7
1.5
PHUB Spokes
0
Peripherals
3
Analog interface and trim, Decimator
4
USB, CAN, I2C, Timers, Counters, and PWMs
5
Reserved
6
UDBs group 1
7
UDBs group 2
4.4.2 DMA Features
When the fairness algorithm is disabled, DMA access is granted
based solely on the priority level; no bus bandwidth guarantees
are made.
„ Twenty-four DMA channels
4.4.4 Transaction Modes Supported
„ Each channel has one or more Transaction Descriptors (TDs)
The flexible configuration of each DMA channel and the ability to
chain multiple channels allow the creation of both simple and
complex use cases. General use cases include, but are not
limited to:
to configure channel behavior. Up to 128 total TDs can be
defined
„ TDs can be dynamically updated
„ Eight levels of priority per channel
Document Number: 001-53304 Rev. *K
Page 16 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
4.4.4.1 Simple DMA
In a simple DMA case, a single TD transfers data between a source and sink (peripherals or memory location). The basic timing
diagrams of DMA read and write cycles are shown in Figure 4-1. For more description on other transfer modes, refer to the Technical
Reference Manual.
Figure 4-1. DMA Timing Diagram
ADDRESS Phase
DATA Phase
ADDRESS Phase
CLK
ADDR 16/32
DATA Phase
CLK
A
B
A
ADDR 16/32
WRITE
B
WRITE
DATA (A)
DATA
READY
DATA (A)
DATA
READY
Basic DMA Read Transfer without wait states
Basic DMA Write Transfer without wait states
A ping pong DMA case uses double buffering to allow one buffer
to be filled by one client while another client is consuming the
data previously received in the other buffer. In its simplest form,
this is done by chaining two TDs together so that each TD calls
the opposite TD when complete.
can set up this configuration information anywhere in system
memory and copy it with a simple TD to the peripheral. After the
configuration phase, a data phase TD (or a series of data phase
TDs) can begin (potentially using scatter gather). When the data
phase TD(s) finish, a status phase TD can be invoked that reads
some memory mapped status information from the peripheral
and copies it to a location in system memory specified by the
CPU for later inspection. Multiple sets of configuration, data, and
status phase “subchains” can be strung together to create larger
chains that transmit multiple packets in this way. A similar
concept exists in the opposite direction to receive the packets.
4.4.4.4 Circular DMA
4.4.4.7 Nested DMA
4.4.4.2 Auto Repeat DMA
Auto repeat DMA is typically used when a static pattern is
repetitively read from system memory and written to a peripheral.
This is done with a single TD that chains to itself.
4.4.4.3 Ping Pong DMA
Circular DMA is similar to ping pong DMA except it contains more
than two buffers. In this case there are multiple TDs; after the last
TD is complete it chains back to the first TD.
4.4.4.5 Scatter Gather DMA
In the case of scatter gather DMA, there are multiple
noncontiguous sources or destinations that are required to
effectively carry out an overall DMA transaction. For example, a
packet may need to be transmitted off of the device and the
packet elements, including the header, payload, and trailer, exist
in various noncontiguous locations in memory. Scatter gather
DMA allows the segments to be concatenated together by using
multiple TDs in a chain. The chain gathers the data from the
multiple locations. A similar concept applies for the reception of
data onto the device. Certain parts of the received data may need
to be scattered to various locations in memory for software
processing convenience. Each TD in the chain specifies the
location for each discrete element in the chain.
One TD may modify another TD, as the TD configuration space
is memory mapped similar to any other peripheral. For example,
a first TD loads a second TD’s configuration and then calls the
second TD. The second TD moves data as required by the
application. When complete, the second TD calls the first TD,
which again updates the second TD’s configuration. This
process repeats as often as necessary.
4.5 Interrupt Controller
The interrupt controller provides a mechanism for hardware
resources to change program execution to a new address,
independent of the current task being executed by the main
code. The interrupt controller provides enhanced features not
found on original 8051 interrupt controllers:
„ Thirty two interrupt vectors
„ Jumps directly to ISR anywhere in code space with dynamic
vector addresses
4.4.4.6 Packet Queuing DMA
„ Multiple sources for each vector
Packet queuing DMA is similar to scatter gather DMA but
specifically refers to packet protocols. With these protocols,
there may be separate configuration, data, and status phases
associated with sending or receiving a packet.
„ Flexible interrupt to vector matching
For instance, to transmit a packet, a memory mapped
configuration register can be written inside a peripheral,
specifying the overall length of the ensuing data phase. The CPU
Document Number: 001-53304 Rev. *K
„ Each interrupt vector is independently enabled or disabled
„ Each interrupt can be dynamically assigned one of eight
priorities
„ Eight level nestable interrupts
Page 17 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Multiple I/O interrupt vectors
„ Software can send interrupts
„ Software can clear pending interrupts
When an interrupt is pending, the current instruction is completed and the program
counter is pushed onto the stack. Code execution then jumps to the program address
provided by the vector. After the ISR is completed, a RETI instruction is executed
and returns execution to the instruction following the previously interrupted
instruction. To do this the RETI instruction pops the program counter from the stack.
If the same priority level is assigned to two or more interrupts, the interrupt with the
lower vector number is executed first. Each interrupt vector may choose from three
interrupt sources: Fixed Function, DMA, and UDB. The fixed function interrupts are
direct connections to the most common interrupt sources and provide the lowest
resource cost connection. The DMA interrupt sources provide direct connections to
the two DMA interrupt sources provided per DMA channel. The third interrupt source
for vectors is from the UDB digital routing array. This allows any digital signal
available to the UDB array to be used as an interrupt source. Fixed function interrupts
and all interrupt sources may be routed to any interrupt vector using the UDB
interrupt source connections.
Figure 4-2 on page 18 represents typical flow of events when an interrupt triggered.
Figure 4-3 on page 19 shows the interrupt structure and priority polling.
Figure 4-2. Interrupt Processing Timing Diagram
1
2
3
4
5
6
7
8
9
10
11
S
CLK
Arrival of new Interrupt
INT_INPUT
S
Pend bit is set on next system clock active edge
POST and PEND bits cleared after IRQ is sleared
PEND
S
Interrupt is posted to ascertain the priority
POST
S
Interrupt request sent to core for processing
IRQ
ACTIVE_INT_NUM
(#10)
INT_VECT_ADDR
NA
NA
0x0010
IRQ cleared after receiving IRA
S
S
The active interrupt
number is posted to core
The active interrupt ISR
address is posted to core
0x0000
S
S
NA
S
IRA
S
IRC
Interrupt generation and posting to CPU
CPU Response
Int. State
Clear
S
Completing current instruction and branching to vector address
Complete ISR and return
TIME
Notes
1: Interrupt triggered asynchronous to the clock
2: The PEND bit is set on next active clock edge to indicate the interrupt arrival
3: POST bit is set following the PEND bit
4: Interrupt request and the interrupt number sent to CPU core after evaluation priority (Takes 3 clocks)
5: ISR address is posted to CPU core for branching
6: CPU acknowledges the interrupt request
Document Number: 001-53304 Rev. *K
Page 18 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
7: ISR address is read by CPU for branching
8, 9: PEND and POST bits are cleared respectively after receiving the IRA from core
10: IRA bit is cleared after completing the current instruction and starting the instruction execution from ISR location (Takes 7 cycles)
11: IRC is set to indicate the completion of ISR, Active int. status is restored with previous status
The total interrupt latency (ISR execution)
= POST + PEND + IRQ + IRA + Completing current instruction and branching
= 1+1+1+2+7 cycles
= 12 cycles
Figure 4-3. Interrupt Structure
Interrupt Polling logic
Interrupts form Fixed
function blocks, DMA and
UDBs
Highest Priority
Interrupt Enable/
Disable, PEND and
POST logic
Interrupts 0 to 30
from UDBs
0
Interrupts 0 to 30
from Fixed
Function Blocks
1
IRQ
8 Level
Priority
decoder
for all
interrupts
Polling sequence
Interrupt
routing logic
to select 31
sources
Interrupt 2 to 29
Interrupts 0 to
30 from DMA
Individual
Enable Disable
bits
0 to 30
ACTIVE_INT_NUM
[15:0]
INT_VECT_ADDR
IRA
IRC
30
Global Enable
disable bit
Document Number: 001-53304 Rev. *K
Lowest Priority
Page 19 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 4-8. Interrupt Vector Table
#
Fixed Function
DMA
phub_termout0[0]
UDB
0
LVD
udb_intr[0]
1
ECC
phub_termout0[1]
udb_intr[1]
2
Reserved
phub_termout0[2]
udb_intr[2]
3
Sleep (Pwr Mgr)
phub_termout0[3]
udb_intr[3]
4
PICU[0]
phub_termout0[4]
udb_intr[4]
5
PICU[1]
phub_termout0[5]
udb_intr[5]
6
PICU[2]
phub_termout0[6]
udb_intr[6]
7
PICU[3]
phub_termout0[7]
udb_intr[7]
8
PICU[4]
phub_termout0[8]
udb_intr[8]
9
PICU[5]
phub_termout0[9]
udb_intr[9]
10
PICU[6]
phub_termout0[10] udb_intr[10]
11
PICU[12]
phub_termout0[11]
12
PICU[15]
phub_termout0[12] udb_intr[12]
13
Comparators
Combined
phub_termout0[13] udb_intr[13]
14
Switched Caps
Combined
phub_termout0[14] udb_intr[14]
15
I2C
phub_termout0[15] udb_intr[15]
16
CAN
phub_termout1[0]
udb_intr[16]
17
Timer/Counter0
phub_termout1[1]
udb_intr[17]
18
Timer/Counter1
phub_termout1[2]
udb_intr[18]
19
Timer/Counter2
phub_termout1[3]
udb_intr[19]
20
Timer/Counter3
phub_termout1[4]
udb_intr[20]
21
USB SOF Int
phub_termout1[5]
udb_intr[21]
22
USB Arb Int
phub_termout1[6]
udb_intr[22]
23
USB Bus Int
phub_termout1[7]
udb_intr[23]
24
USB Endpoint[0]
phub_termout1[8]
udb_intr[24]
25
USB Endpoint Data phub_termout1[9]
udb_intr[25]
26
Reserved
phub_termout1[10] udb_intr[26]
udb_intr[11]
27
LCD
phub_termout1[11]
28
Reserved
phub_termout1[12] udb_intr[28]
29
Decimator Int
phub_termout1[13] udb_intr[29]
30
PHUB Error Int
phub_termout1[14] udb_intr[30]
31
EEPROM Fault Int
phub_termout1[15] udb_intr[31]
Document Number: 001-53304 Rev. *K
udb_intr[27]
Page 20 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
5. Memory
5.1 Static RAM
CY8C34 Static RAM (SRAM) is used for temporary data storage.
Up to 8 KB of SRAM is provided and can be accessed by the
8051 or the DMA controller. See Memory Map on page 23.
Simultaneous access of SRAM by the 8051 and the DMA
controller is possible if different 4-KB blocks are accessed.
5.2 Flash Program Memory
Flash memory in PSoC devices provides nonvolatile storage for
user firmware, user configuration data, bulk data storage, and
optional ECC data. The main flash memory area contains up to
64 KB of user program space.
Up to an additional 8 KB of flash space is available for Error
Correcting Codes (ECC). If ECC is not used this space can store
device configuration data and bulk user data. User code may not
be run out of the ECC flash memory section. ECC can correct
one bit error and detect two bit errors per 8 bytes of firmware
memory; an interrupt can be generated when an error is
detected.
Flash is read in units of rows; each row is 9 bytes wide with 8
bytes of data and 1 byte of ECC data. When a row is read, the
data bytes are copied into an 8-byte instruction buffer. The CPU
fetches its instructions from this buffer, for improved CPU
performance.
Flash programming is performed through a special interface and
preempts code execution out of flash. The flash programming
interface performs flash erasing, programming and setting code
protection levels. Flash in-system serial programming (ISSP),
typically used for production programming, is possible through
both the SWD and JTAG interfaces. In-system programming,
typically used for bootloaders, is also possible using serial
interfaces such as I2C, USB, UART, and SPI, or any
communications protocol.
5.3 Flash Security
All PSoC devices include a flexible flash-protection model that
prevents access and visibility to on-chip flash memory. This
prevents duplication or reverse engineering of proprietary code.
Flash memory is organized in blocks, where each block contains
256 bytes of program or data and 32 bytes of ECC or
configuration data. A total of up to 256 blocks is provided on
64-KB flash devices.
The device offers the ability to assign one of four protection
levels to each row of flash. Table 5-1 lists the protection modes
available. Flash protection levels can only be changed by
performing a complete flash erase. The Full Protection and Field
Upgrade settings disable external access (through a debugging
tool such as PSoC Creator, for example). If your application
requires code update through a boot loader, then use the Field
Upgrade setting. Use the Unprotected setting only when no
Document Number: 001-53304 Rev. *K
security is needed in your application. The PSoC device also
offers an advanced security feature called Device Security which
permanently disables all test, programming, and debug ports,
protecting your application from external access (see the
“Device Security” section on page 61). For more information
about how to take full advantage of the security features in
PSoC, see the PSoC 3 TRM.
Table 5-1. Flash Protection
Protection
Setting
Allowed
Not Allowed
Unprotected
External read and write + internal read and write
Factory
Upgrade
External write + internal
read and write
External read
Field Upgrade
Internal read and write
External read and
write
Full Protection
Internal read
External read and
write + internal write
Disclaimer
Note the following details of the flash code protection features on
Cypress devices.
Cypress products meet the specifications contained in their
particular Cypress data sheets. Cypress believes that its family
of products is one of the most secure families of its kind on the
market today, regardless of how they are used. There may be
methods, unknown to Cypress, that can breach the code
protection features. Any of these methods, to our knowledge,
would be dishonest and possibly illegal. Neither Cypress nor any
other semiconductor manufacturer can guarantee the security of
their code. Code protection does not mean that we are
guaranteeing the product as “unbreakable.”
Cypress is willing to work with the customer who is concerned
about the integrity of their code. Code protection is constantly
evolving. We at Cypress are committed to continuously
improving the code protection features of our products.
5.4 EEPROM
PSoC EEPROM memory is a byte-addressable nonvolatile
memory. The CY8C34 has up to 2 KB of EEPROM memory to
store user data. Reads from EEPROM are random access at the
byte level. Reads are done directly; writes are done by sending
write commands to an EEPROM programming interface. CPU
code execution can continue from flash during EEPROM writes.
EEPROM is erasable and writeable at the row level. The
EEPROM is divided into 128 rows of 16 bytes each.
The CPU can not execute out of EEPROM. There is no ECC
hardware associated with EEPROM. If ECC is required it must
be handled in firmware.
Page 21 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
5.5 Nonvolatile Latches (NVLs)
PSoC has a 4-byte array of nonvolatile latches (NVLs) that are used to configure the device at reset. The NVL register map is shown
in Table 5-2.
Table 5-2. Device Configuration NVL Register Map
Register Address
7
6
5
4
3
2
1
0
0x00
PRT3RDM[1:0]
PRT2RDM[1:0]
PRT1RDM[1:0]
PRT0RDM[1:0]
0x01
PRT12RDM[1:0]
PRT6RDM[1:0]
PRT5RDM[1:0]
PRT4RDM[1:0]
0x02
XRESMEN
0x03
PRT15RDM[1:0]
DIG_PHS_DLY[3:0]
ECCEN
DPS[1:0]
The details for individual fields and their factory default settings are shown in Table 5-3:.
Table 5-3. Fields and Factory Default Settings
Field
Description
Settings
PRTxRDM[1:0]
Controls reset drive mode of the corresponding IO port. 00b (default) - high impedance analog
See “Reset Configuration” on page 38. All pins of the port 01b - high impedance digital
are set to the same mode.
10b - resistive pull up
11b - resistive pull down
XRESMEN
0 (default for 68-pin and 100-pin parts) - GPIO
Controls whether pin P1[2] is used as a GPIO or as an
external reset. See “Pin Descriptions” on page 10, XRES 1 (default for 48-pin parts) - external reset
description.
DPS{1:0]
Controls the usage of various P1 pins as a debug port.
See “Programming, Debug Interfaces, Resources” on
page 60.
ECCEN
Controls whether ECC flash is used for ECC or for general 0 (default) - ECC disabled
configuration and data storage. See “Flash Program
1 - ECC enabled
Memory” on page 21.
DIG_PHS_DLY[3:0]
Selects the digital clock phase delay.
00b - 5-wire JTAG
01b (default) - 4-wire JTAG
10b - SWD
11b - debug ports disabled
See the TRM for details.
Although PSoC Creator provides support for modifying the device configuration NVLs, the number of NVL erase / write cycles is limited
– see “Nonvolatile Latches (NVL))” on page 101.
Document Number: 001-53304 Rev. *K
Page 22 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
5.6 External Memory Interface
CY8C34 provides an External Memory Interface (EMIF) for
connecting to external memory devices. The connection allows
read and write accesses to external memories. The EMIF
operates in conjunction with UDBs, I/O ports, and other
hardware to generate external memory address and control
signals. At 33 MHz, each memory access cycle takes four bus
clock cycles.
Figure 5-1 is the EMIF block diagram. The EMIF supports
synchronous and asynchronous memories. The CY8C34
supports only one type of external memory device at a time.
External memory can be accessed via the 8051 xdata space; up
to 24 address bits can be used. See “xdata Space” section on
page 25. The memory can be 8 or 16 bits wide.
Figure 5-1. EMIF Block Diagram
Address Signals
External_ MEM_ ADDR[23:0]
IO
PORTs
Data Signals
External_ MEM_ DATA[15:0]
IO
PORTs
Control Signals
IO
PORTs
Data,
Address,
and Control
Signals
IO IF
PHUB
Data,
Address,
and Control
Signals
Control
DSI Dynamic Output
Control
UDB
DSI to Port
Data,
Address,
and Control
Signals
EM Control
Signals
Other
Control
Signals
EMIF
5.7 Memory Map
5.7.2 Internal Data Space
The CY8C34 8051 memory map is very similar to the MCS-51
memory map.
The CY8C34 8051 internal data space is 384 bytes, compressed
within a 256-byte space. This space consists of 256 bytes of
RAM (in addition to the SRAM mentioned in Static RAM on page
21) and a 128-byte space for Special Function Registers (SFRs).
See Figure 5-2. The lowest 32 bytes are used for 4 banks of
registers R0-R7. The next 16 bytes are bit-addressable.
5.7.1 Code Space
The CY8C34 8051 code space is 64 KB. Only main flash exists
in this space. See the “Flash Program Memory” section on
page 21.
Document Number: 001-53304 Rev. *K
Page 23 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 5-2. 8051 Internal Data Space
0x00
In addition to the register or bit address modes used with the
lower 48 bytes, the lower 128 bytes can be accessed with direct
or indirect addressing. With direct addressing mode, the upper
128 bytes map to the SFRs. With indirect addressing mode, the
upper 128 bytes map to RAM. Stack operations use indirect
addressing; the 8051 stack space is 256 bytes. See the
“Addressing Modes” section on page 11
4 Banks, R0-R7 Each
0x1F
0x20
Bit-Addressable Area
0x2F
0x30
Lower Core RAM Shared with Stack Space
(direct and indirect addressing)
0x7F
0x80
Upper Core RAM Shared
with Stack Space
(indirect addressing)
0xFF
SFR
Special Function Registers
(direct addressing)
5.7.3 SFRs
The Special Function Register (SFR) space provides access to frequently accessed registers. The memory map for the SFR memory
space is shown in Table 5-4.
Table 5-4. SFR Map
Address
0/8
0×F8
SFRPRT15DR
0×F0
B
0×E8
SFRPRT12DR
0×E0
ACC
0×D8
SFRPRT6DR
0×D0
PSW
0×C8
0×C0
1/9
SFRPRT15PS
2/A
3/B
4/C
5/D
6/E
7/F
SFRPRT15SEL
SFRPRT12SEL
SFRPRT12PS
MXAX
SFRPRT6PS
SFRPRT6SEL
SFRPRT5DR
SFRPRT5PS
SFRPRT5SEL
SFRPRT4DR
SFRPRT4PS
SFRPRT4SEL
SFRPRT3DR
SFRPRT3PS
SFRPRT3SEL
0×B8
0×B0
0×A8
IE
0×A0
P2AX
SFRPRT1SEL
0×98
SFRPRT2DR
SFRPRT2PS
0×90
SFRPRT1DR
SFRPRT1PS
0×88
0×80
SFRPRT0DR
SFRPRT2SEL
DPX0
SFRPRT0PS
SFRPRT0SEL
SP
DPL0
The CY8C34 family provides the standard set of registers found
on industry standard 8051 devices. In addition, the CY8C34
devices add SFRs to provide direct access to the I/O ports on the
device. The following sections describe the SFRs added to the
CY8C34 family.
XData Space Access SFRs
The 8051 core features dual DPTR registers for faster data
transfer operations. The data pointer select SFR, DPS, selects
which data pointer register, DPTR0 or DPTR1, is used for the
following instructions:
„ MOVX @DPTR, A
„ MOVX A, @DPTR
„ MOVC A, @A+DPTR
„ JMP @A+DPTR
Document Number: 001-53304 Rev. *K
DPH0
DPX1
DPL1
DPH1
DPS
„ INC DPTR
„ MOV DPTR, #data16
The extended data pointer SFRs, DPX0, DPX1, MXAX, and
P2AX, hold the most significant parts of memory addresses
during access to the xdata space. These SFRs are used only
with the MOVX instructions.
During a MOVX instruction using the DPTR0/DPTR1 register,
the most significant byte of the address is always equal to the
contents of DPX0/DPX1. During a MOVX instruction using the
R0 or R1 register, the most significant byte of the address is
always equal to the contents of MXAX, and the next most
significant byte is always equal to the contents of P2AX.
I/O Port SFRs
The I/O ports provide digital input sensing, output drive, pin
interrupts, connectivity for analog inputs and outputs, LCD, and
Page 24 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
access to peripherals through the DSI. Full information on I/O
ports is found in I/O System and Routing on page 32.
Table 5-5. XDATA Data Address Map (continued)
„ SFRPRTxDR sets the output data state of the port (where x is
Address Range
0×01 0000 – 0×01
FFFF
0×05 0220 – 0×05 02F0
0×08 0000 – 0×08 1FFF
0×80 0000 – 0×FF
FFFF
„ The SFRPRTxSEL selects whether the PHUB PRTxDR
6. System Integration
I/O ports are linked to the CPU through the PHUB and are also
available in the SFRs. Using the SFRs allows faster access to a
limited set of I/O port registers, while using the PHUB allows boot
configuration and access to all I/O port registers.
Each SFR supported I/O port provides three SFRs:
port number and includes ports 0-6, 12 and 15)
register or the SFRPRTxDR controls each pin’s output buffer
within the port. If a SFRPRTxSEL[y] bit is high, the
corresponding SFRPRTxDR[y] bit sets the output state for that
pin. If a SFRPRTxSEL[y] bit is low, the corresponding
PRTxDR[y] bit sets the output state of the pin (where y varies
from 0 to 7).
„ The SFRPRTxPS is a read only register that contains pin state
values of the port pins.
5.7.3.1 xdata Space
The 8051 xdata space is 24-bit, or 16 MB in size. The majority of
this space is not “external”—it is used by on-chip components.
See Table 5-5. External, that is, off-chip, memory can be
accessed using the EMIF. See External Memory Interface on
page 23.
Table 5-5. XDATA Data Address Map
Address Range
0×00 0000 – 0×00 1FFF
0×00 4000 – 0×00 42FF
0×00 4300 – 0×00 43FF
0×00 4400 – 0×00 44FF
0×00 4500 – 0×00 45FF
0×00 4700 – 0×00 47FF
0×00 4900 – 0×00 49FF
0×00 4E00 – 0×00
4EFF
0×00 4F00 – 0×00
4FFF
0×00 5000 – 0×00 51FF
0×00 5400 – 0×00 54FF
0×00 5800 – 0×00 5FFF
0×00 6000 – 0×00 60FF
0×00 6400 – 0×00 6FFF
0×00 7000 – 0×00 7FFF
0×00 8000 – 0×00 8FFF
0×00 A000 – 0×00
A400
Purpose
SRAM
Clocking, PLLs, and oscillators
Power management
Interrupt controller
Ports interrupt control
Flash programming interface
I2C controller
Decimator
Fixed timer/counter/PWMs
I/O ports control
External Memory Interface (EMIF)
control registers
Analog Subsystem interface
USB controller
UDB configuration
PHUB configuration
EEPROM
CAN
Purpose
Digital Interconnect configuration
Debug controller
Flash ECC bytes
External Memory Interface
6.1 Clocking System
The clocking system generates, divides, and distributes clocks
throughout the PSoC system. For the majority of systems, no
external crystal is required. The IMO and PLL together can
generate up to a 50 MHz clock, accurate to ±1 percent over
voltage and temperature. Additional internal and external clock
sources allow each design to optimize accuracy, power, and
cost. All of the system clock sources can be used to generate
other clock frequencies in the 16-bit clock dividers and UDBs for
anything the user wants, for example a UART baud rate
generator.
Clock generation and distribution is automatically configured
through the PSoC Creator IDE graphical interface. This is based
on the complete system’s requirements. It greatly speeds the
design process. PSoC Creator allows you to build clocking
systems with minimal input. You can specify desired clock
frequencies and accuracies, and the software locates or builds a
clock that meets the required specifications. This is possible
because of the programmability inherent PSoC.
Key features of the clocking system include:
„ Seven general purpose clock sources
3- to 24-MHz IMO, ±1 percent at 3 MHz
4- to 25-MHz external crystal oscillator (MHzECO)
‡ Clock doubler provides a doubled clock frequency output for
the USB block, see USB Clock Domain on page 28
‡ DSI signal from an external I/O pin or other logic
‡ 24- to 50- MHz fractional PLL sourced from IMO, MHzECO,
or DSI
‡ Clock Doubler
‡ 1 kHz, 33 kHz, 100 kHz ILO for Watch Dog Timer (WDT) and
Sleep Timer
‡ 32.768-kHz external crystal oscillator (kHzECO) for RTC
„ IMO has a USB mode that auto locks to the USB bus clock
requiring no external crystal for USB. (USB equipped parts only)
‡
‡
„ Independently sourced clock in all clock dividers
„ Eight 16-bit clock dividers for the digital system
„ Four 16-bit clock dividers for the analog system
„ Dedicated 16-bit divider for the bus clock
„ Dedicated 4-bit divider for the CPU clock
„ Automatic clock configuration in PSoC Creator
Document Number: 001-53304 Rev. *K
Page 25 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 6-1. Oscillator Summary
Source
IMO
MHzECO
Fmin
3 MHz
4 MHz
Tolerance at Fmin
±1% over voltage and temperature
Crystal dependent
Fmax
24 MHz
25 MHz
Tolerance at Fmax
±4%
Crystal dependent
Startup Time
10 µs max
5 ms typ, max is
crystal dependent
DSI
PLL
Doubler
ILO
0 MHz
24 MHz
12 MHz
1 kHz
Input dependent
Input dependent
Input dependent
–50%, +100%
50 MHz
50 MHz
48 MHz
100 kHz
Input dependent
Input dependent
Input dependent
–55%, +100%
Input dependent
250 µs max
1 µs max
15 ms max in lowest
power mode
kHzECO
32 kHz
Crystal dependent
32 kHz
Crystal dependent
500 ms typ, max is
crystal dependent
Figure 6-1. Clocking Subsystem
3-24 MHz
IMO
4-25 MHz
ECO
External IO
or DSI
0-50 MHz
32 kHz ECO
1,33,100 kHz
ILO
12-48 MHz
Doubler
CPU
Clock
CPU Clock Divider
4 bit
24-50 MHz
PLL
System
Clock Mux
Bus
Clock
Bus Clock Divider
16 bit
7
Digital Clock
Divider 16 bit
Digital Clock
Divider 16 bit
Analog Clock
Divider 16 bit
s
k
e
w
Digital Clock
Divider 16 bit
Digital Clock
Divider 16 bit
Analog Clock
Divider 16 bit
s
k
e
w
7
Digital Clock
Divider 16 bit
Digital Clock
Divider 16 bit
Analog Clock
Divider 16 bit
s
k
e
w
Digital Clock
Divider 16 bit
Digital Clock
Divider 16 bit
Analog Clock
Divider 16 bit
s
k
e
w
6.1.1 Internal Oscillators
6.1.1.2 Clock Doubler
6.1.1.1 Internal Main Oscillator
The clock doubler outputs a clock at twice the frequency of the
input clock. The doubler works for input frequency ranges of 6 to
24 MHz (providing 12 to 48 MHz at the output). It can be
configured to use a clock from the IMO, MHzECO, or the DSI
(external pin). The doubler is typically used to clock the USB.
In most designs the IMO is the only clock source required, due
to its ±1-percent accuracy. The IMO operates with no external
components and outputs a stable clock. A factory trim for each
frequency range is stored in the device. With the factory trim,
tolerance varies from ±1 percent at 3 MHz, up to ±4 percent at
24 MHz. The IMO, in conjunction with the PLL, allows generation
of CPU and system clocks up to the device's maximum
frequency (see Phase-Locked Loop).
The IMO provides clock outputs at 3, 6, 12, and 24 MHz.
Document Number: 001-53304 Rev. *K
6.1.1.3 Phase-Locked Loop
The PLL allows low-frequency, high-accuracy clocks to be
multiplied to higher frequencies. This is a trade off between
higher clock frequency and accuracy and, higher power
consumption and increased startup time.
Page 26 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The PLL block provides a mechanism for generating clock
frequencies based upon a variety of input sources. The PLL
outputs clock frequencies in the range of 24 to 50 MHz. Its input
and feedback dividers supply 4032 discrete ratios to create
almost any desired system clock frequency. The accuracy of the
PLL output depends on the accuracy of the PLL input source.
The most common PLL use is to multiply the IMO clock at 3 MHz,
where it is most accurate to generate the CPU and system clocks
up to the device’s maximum frequency.
The PLL achieves phase lock within 250 µs (verified by bit
setting). It can be configured to use a clock from the IMO,
MHzECO or DSI (external pin). The PLL clock source can be
used until lock is complete and signaled with a lock bit. The lock
signal can be routed through the DSI to generate an interrupt.
Disable the PLL before entering low-power modes.
6.1.1.4 Internal Low-Speed Oscillator
The ILO provides clock frequencies for low-power consumption,
including the watchdog timer, and sleep timer. The ILO
generates up to three different clocks: 1 kHz, 33 kHz, and
100 kHz.
The 1 kHz clock (CLK1K) is typically used for a background
‘heartbeat’ timer. This clock inherently lends itself to low-power
supervisory operations such as the watchdog timer and long
sleep intervals using the central timewheel (CTW).
The central timewheel is a 1 kHz, free running, 13-bit counter
clocked by the ILO. The central timewheel is always enabled
except in hibernate mode and when the CPU is stopped during
debug on chip mode. It can be used to generate periodic
interrupts for timing purposes or to wake the system from a
low-power mode. Firmware can reset the central timewheel.
Systems that require accurate timing should use the RTC
capability instead of the central timewheel.
Figure 6-2. MHzECO Block Diagram
4 – 25 MHz
Crystal Osc
Xi
(Pin P15[1])
The 33 kHz clock (CLK33K) comes from a divide-by-3 operation
on CLK100K. This output can be used as a reduced accuracy
version of the 32.768-kHz ECO clock with no need for a crystal.
6.1.2 External Oscillators
Xo
(Pin P15[0])
4 – 25 MHz
crystal
External
Components
Capacitors
6.1.2.2 32.768-kHz ECO
The 32.768-kHz External Crystal Oscillator (32kHzECO)
provides precision timing with minimal power consumption using
an external 32.768-kHz watch crystal (see Figure 6-3). The
32kHzECO also connects directly to the sleep timer and provides
the source for the RTC. The RTC uses a 1-second interrupt to
implement the RTC functionality in firmware.
The oscillator works in two distinct power modes. This allows
users to trade off power consumption with noise immunity from
neighboring circuits. The GPIO pins connected to the external
crystal and capacitors are fixed.
Figure 6-3. 32kHzECO Block Diagram
The 100 kHz clock (CLK100K) works as a low-power system
clock to run the CPU. It can also generate time intervals such as
fast sleep intervals using the fast timewheel.
The fast timewheel is a 100 kHz, 5-bit counter clocked by the ILO
that can also be used to wake the system. The fast timewheel
settings are programmable, and the counter automatically resets
when the terminal count is reached. This enables flexible,
periodic wakeups of the CPU at a higher rate than is allowed
using the central timewheel. The fast timewheel can generate an
optional interrupt each time the terminal count is reached.
XCLK_MHZ
32 kHz
Crystal Osc
Xi
(Pin P15[3])
External
Components
XCLK32K
Xo
(Pin P15[2])
32 kHz
crystal
Capacitors
6.1.2.1 MHz External Crystal Oscillator
The MHzECO provides high frequency, high precision clocking
using an external crystal (see Figure 6-2). It supports a wide
variety of crystal types, in the range of 4 to 25 MHz. When used
in conjunction with the PLL, it can generate CPU and system
clocks up to the device's maximum frequency (see
“Phase-Locked Loop” section on page 26). The GPIO pins
connecting to the external crystal and capacitors are fixed.
MHzECO accuracy depends on the crystal chosen.
Document Number: 001-53304 Rev. *K
6.1.2.3 Digital System Interconnect
The DSI provides routing for clocks taken from external clock
oscillators connected to I/O. The oscillators can also be
generated within the device in the digital system and Universal
Digital Blocks.
While the primary DSI clock input provides access to all clocking
resources, up to eight other DSI clocks (internally or externally
generated) may be routed directly to the eight digital clock
dividers. This is only possible if there are multiple precision clock
sources.
Page 27 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Each clock divider consists of an 8-input multiplexer, a 16-bit
clock divider (divide by 2 and higher) that generates ~50 percent
duty cycle clocks, system clock resynchronization logic, and
deglitch logic. The outputs from each digital clock tree can be
routed into the digital system interconnect and then brought back
into the clock system as an input, allowing clock chaining of up
to 32 bits.
6.1.3 Clock Distribution
All seven clock sources are inputs to the central clock distribution
system. The distribution system is designed to create multiple
high precision clocks. These clocks are customized for the
design’s requirements and eliminate the common problems
found with limited resolution prescalers attached to peripherals.
The clock distribution system generates several types of clock
trees.
„ The system clock is used to select and supply the fastest clock
in the system for general system clock requirements and clock
synchronization of the PSoC device.
„ Bus Clock 16-bit divider uses the system clock to generate the
system's bus clock used for data transfers. Bus clock is the
source clock for the CPU clock divider.
„ Eight fully programmable 16-bit clock dividers generate digital
system clocks for general use in the digital system, as
configured by the design’s requirements. Digital system clocks
can generate custom clocks derived from any of the seven
clock sources for any purpose. Examples include baud rate
generators, accurate PWM periods, and timer clocks, and
many others. If more than eight digital clock dividers are
required, the Universal Digital Blocks (UDBs) and fixed function
Timer/Counter/PWMs can also generate clocks.
„ Four 16-bit clock dividers generate clocks for the analog system
components that require clocking, such as ADC and mixers.
The analog clock dividers include skew control to ensure that
critical analog events do not occur simultaneously with digital
switching events. This is done to reduce analog system noise.
6.1.4 USB Clock Domain
The USB clock domain is unique in that it operates largely
asynchronously from the main clock network. The USB logic
contains a synchronous bus interface to the chip, while running
on an asynchronous clock to process USB data. The USB logic
requires a 48 MHz frequency. This frequency can be generated
from different sources, including DSI clock at 48 MHz or doubled
value of 24 MHz from internal oscillator, DSI signal, or crystal
oscillator.
6.2 Power System
The power system consists of separate analog, digital, and I/O
supply pins, labeled Vdda, Vddd, and Vddiox, respectively. It
also includes two internal 1.8 V regulators that provide the digital
(Vccd) and analog (Vcca) supplies for the internal core logic. The
output pins of the regulators (Vccd and Vcca) and the Vddio pins
must have capacitors connected as shown in Figure 6-4. The
two Vccd pins must be shorted together, with as short a trace as
possible, and connected to a 1 µF ±10 percent X5R capacitor.
The power system also contains a sleep regulator, an I2C
regulator, and a hibernate regulator.
Figure 6-4. PSoC Power System
Vddd
1 µF
Vddio2
Vddd
I /O Supply
Vssd
Vccd
Vddio2
Vddio0
0.1 µF
0.1µF
I/O Supply
Vddio0
0.1 µF
I2C
Regulator
Sleep
Regulator
Digital
Domain
Vdda
Vdda
Digital
Regulators
Vssd
Vcca
Analog
Regulator
0.1µF
1 µF
.
Vssa
Analog
Domain
0.1 µF
I/O Supply
Vddio3
Vddd
Vssd
I/O Supply
Vccd
Vddio1
Hibernate
Regulator
0.1 µF
0.1µF
Vddio1
Document Number: 001-53304 Rev. *K
Vddd
Vddio3
Page 28 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Sleep
Note The two Vccd pins must be connected together with as
short a trace as possible. A trace under the device is
recommended, as shown in Figure 2-6 on page 10.
„ Hibernate
Active is the main processing mode. Its functionality is
configurable. Each power controllable subsystem is enabled or
disabled by using separate power configuration template
registers. In alternate active mode, fewer subsystems are
enabled, reducing power. In sleep mode most resources are
disabled regardless of the template settings. Sleep mode is
optimized to provide timed sleep intervals and RTC functionality.
The lowest power mode is hibernate, which retains register and
SRAM state, but no clocks, and allows wakeup only from I/O
pins. Figure 6-5 on page 30 illustrates the allowable transitions
between power modes.
6.2.1 Power Modes
PSoC 3 devices have four different power modes, as shown in
Table 6-2 and Table 6-3. The power modes allow a design to
easily provide required functionality and processing power while
simultaneously minimizing power consumption and maximizing
battery life in low-power and portable devices.
PSoC 3 power modes, in order of decreasing power
consumption are:
„ Active
„ Alternate Active
Table 6-2. Power Modes
Power Modes
Description
Entry Condition Wakeup Source
Active Clocks
Regulator
Active
Primary mode of operation, all
peripherals available (programmable)
Wakeup, reset,
manual register
entry
Any interrupt
Any
(programmable)
All regulators available.
Digital and analog
regulators can be disabled if
external regulation used.
Alternate
Active
Similar to Active mode, and is
Manual register
typically configured to have fewer entry
peripherals active to reduce
power. One possible
configuration is to use the UDBs
for processing, with the CPU
turned off
Any interrupt
Any
(programmable)
All regulators available.
Digital and analog
regulators can be disabled if
external regulation used.
Sleep
All subsystems automatically
disabled
Comparator,
ILO/kHzECO
PICU, I2C, RTC,
CTW, LVD
Both digital and analog
regulators buzzed.
Digital and analog
regulators can be disabled if
external regulation used.
Hibernate
All subsystems automatically
Manual register
disabled
entry
Lowest power consuming mode
with all peripherals and internal
regulators disabled, except
hibernate regulator is enabled
Configuration and memory
contents retained
PICU
Only hibernate regulator
active.
Manual register
entry
Table 6-3. Power Modes Wakeup Time and Power Consumption
Sleep
Modes
Wakeup
Time
Current
(typ)
Active
–
Alternat
e Active
Sleep
Hibernat
e
Code
Execution
Digital
Resources
Analog
Resources
Clock Sources
Available
Wakeup Sources
Reset
Sources
1.2 mA[13]
Yes
All
–
–
User
defined
All
All
All
–
All
All
All
–
All
<15 µs
1 µA
No
I2C
Comparator
ILO/kHzECO
Comparator,
PICU, I2C, RTC,
CTW, LVD
XRES, LVD,
WDR
<100 µs
200 nA
No
None
None
None
PICU
XRES
Note
13. Bus clock off. Execute from CPU instruction buffer at 6 MHz. See Table 11-2 on page 64.
Document Number: 001-53304 Rev. *K
Page 29 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
I/O interrupts. Internal interrupt sources can come from a variety
of peripherals, such as analog comparators and UDBs. The
central timewheel provides periodic interrupts to allow the
system to wake up, poll peripherals, or perform real-time
functions. Reset event sources include the external reset I/O pin
(XRES), WDT, and Precision Reset (PRES).
Figure 6-5. Power Mode Transitions
Active
6.2.2 Boost Converter
Manual
Sleep
Hibernate
Buzz
Alternate
Active
6.2.1.1 Active Mode
Active mode is the primary operating mode of the device. When
in active mode, the active configuration template bits control
which available resources are enabled or disabled. When a
resource is disabled, the digital clocks are gated, analog bias
currents are disabled, and leakage currents are reduced as
appropriate. User firmware can dynamically control subsystem
power by setting and clearing bits in the active configuration
template. The CPU can disable itself, in which case the CPU is
automatically reenabled at the next wakeup event.
When a wakeup event occurs, the global mode is always
returned to active, and the CPU is automatically enabled,
regardless of its template settings. Active mode is the default
global power mode upon boot.
6.2.1.2 Alternate Active Mode
Alternate Active mode is very similar to Active mode. In alternate
active mode, fewer subsystems are enabled, to reduce power
consumption. One possible configuration is to turn off the CPU
and flash, and run peripherals at full speed.
6.2.1.3 Sleep Mode
Sleep mode reduces power consumption when a resume time of
15 µs is acceptable. The wake time is used to ensure that the
regulator outputs are stable enough to directly enter active
mode.
Applications that use a supply voltage of less than 1.71 V, such
as solar or single cell battery supplies, may use the on-chip boost
converter. The boost converter may also be used in any system
that requires a higher operating voltage than the supply provides.
For instance, this includes driving 5.0 V LCD glass in a 3.3 V
system. The boost converter accepts an input voltage as low as
0.5 V. With one low cost inductor it produces a selectable output
voltage sourcing enough current to operate the PSoC and other
on-board components.
The boost converter accepts an input voltage from 0.5 V to 5.5 V
(Vbat), and can start up with Vbat as low as 0.5 V. The converter
provides a user configurable output voltage of 1.8 to 5.0 V
(Vboost). Vbat is typically less than Vboost; if Vbat is greater than
or equal to Vboost, then VBOOST will be the same as Vbat. The
block can deliver up to 50 mA (IBOOST) depending on
configuration.
Four pins are associated with the boost converter: Vbat, Vssb,
Vboost, and Ind. The boosted output voltage is sensed at the
Vboost pin and must be connected directly to the chip’s supply
inputs. An inductor is connected between the Vbat and Ind pins.
You can optimize the inductor value to increase the boost
converter efficiency based on input voltage, output voltage,
current and switching frequency. The external Schottky diode
shown in Figure 6-6 is required only in cases when Vboost >
3.6 V.
Figure 6-6. Application for Boost Converter
Vboost
Optional
Schottky Diode
Only required
Vboost >3.6 V
Vdda Vddd Vddio
Ind
10 µH
SMP
PSoC
22 µF 0. 1 µF
6.2.1.4 Hibernate Mode
In hibernate mode nearly all of the internal functions are
disabled. Internal voltages are reduced to the minimal level to
keep vital systems alive. Configuration state is preserved in
hibernate mode and SRAM memory is retained. GPIOs
configured as digital outputs maintain their previous values and
external GPIO pin interrupt settings are preserved. The device
can only return from hibernate mode in response to an external
I/O interrupt. The resume time from hibernate mode is less than
100 µs.
6.2.1.5 Wakeup Events
Wakeup events are configurable and can come from an interrupt
or device reset. A wakeup event restores the system to active
mode. Firmware enabled interrupt sources include internally
generated interrupts, power supervisor, central timewheel, and
Document Number: 001-53304 Rev. *K
22 µF
Vbat
Vssb
Vssa
Vssd
The switching frequency can be set to 100 kHz, 400 kHz, 2 MHz,
or 32 kHz to optimize efficiency and component cost. The
100 kHz, 400 kHz, and 2 MHz switching frequencies are
generated using oscillators internal to the boost converter block.
When the 32-kHz switching frequency is selected, the clock is
derived from a 32 kHz external crystal oscillator. The 32-kHz
external clock is primarily intended for boost standby mode.
At 2 MHz the Vboost output is limited to 2 × Vbat, and at 400 kHz
Vboost is limited to 4 × Vbat.
Page 30 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The boost converter can be operated in two different modes:
active and standby. Active mode is the normal mode of operation
where the boost regulator actively generates a regulated output
voltage. In standby mode, most boost functions are disabled,
thus reducing power consumption of the boost circuit. The
converter can be configured to provide low-power, low current
regulation in the standby mode. The external 32 kHz crystal can
be used to generate inductor boost pulses on the rising and
falling edge of the clock when the output voltage is less than the
programmed value. This is called automatic thump mode (ATM).
The boost typically draws 200 µA in active mode and 12 µA in
standby mode. The boost operating modes must be used in
conjunction with chip power modes to minimize the total chip
power consumption. Table 6-4 lists the boost power modes
available in different chip power modes.
Table 6-4. Chip and Boost Power Modes Compatibility
Chip Power Modes
Figure 6-7. Resets
Vddd Vdda
Power
Voltage
Level
Monitors
Reset
Pin
External
Reset
Processor
Interrupt
Reset
Controller
System
Reset
Watchdog
Timer
Boost Power Modes
Chip – Active mode
Boost can be operated in either active or
standby mode.
Chip – Sleep mode
Boost can be operated in either active or
standby mode. However, it is recommended to operate boost in standby
mode for low-power consumption
Chip – Hibernate mode Boost can only be operated in active
mode. However, it is recommended not
to use boost in chip hibernate mode due
to high current consumption in boost
active mode
Software
Reset
Register
The term device reset indicates that the processor as well as
analog and digital peripherals and registers are reset.
A reset status register holds the source of the most recent reset
or power voltage monitoring interrupt. The program may
examine this register to detect and report exception conditions.
This register is cleared after a power-on reset.
6.3.1 Reset Sources
If the boost converter is not used in a given application, tie the
VBAT, VSSB, and VBOOST pins to ground and leave the Ind pin
unconnected.
6.3 Reset
CY8C34 has multiple internal and external reset sources
available. The reset sources are:
„ Power source monitoring – The analog and digital power
voltages, Vdda, Vddd, Vcca, and Vccd are monitored in several
different modes during power up, active mode, and sleep mode
(buzzing). If any of the voltages goes outside predetermined
ranges then a reset is generated. The monitors are
programmable to generate an interrupt to the processor under
certain conditions before reaching the reset thresholds.
„ External – The device can be reset from an external source by
pulling the reset pin (XRES) low. The XRES pin includes an
internal pull-up to Vddio1. Vddd, Vdda, and Vddio1 must all
have voltage applied before the part comes out of reset.
„ Watchdog timer – A watchdog timer monitors the execution of
instructions by the processor. If the watchdog timer is not reset
by firmware within a certain period of time, the watchdog timer
generates a reset.
„ Software – The device can be reset under program control.
Document Number: 001-53304 Rev. *K
6.3.1.1 Power Voltage Level Monitors
„ IPOR – Initial Power-on Reset
At initial power-on, IPOR monitors the power voltages Vddd
and Vdda, both directly at the pins and at the outputs of the
corresponding internal regulators. The trip level is not precise.
It is set to approximately 1 volt, which is below the lowest
specified operating voltage but high enough for the internal
circuits to be reset and to hold their reset state. The monitor
generates a reset pulse that is at least 100 ns wide. It may be
much wider if one or more of the voltages ramps up slowly.
To save power the IPOR circuit is disabled when the internal
digital supply is stable. Voltage supervision is then handed off
to the precise low voltage reset (PRES) circuit. When the
voltage is high enough for PRES to release, the IMO starts.
„ PRES – Precise Low Voltage Reset
This circuit monitors the outputs of the analog and digital
internal regulators after power up. The regulator outputs are
compared to a precise reference voltage. The response to a
PRES trip is identical to an IPOR reset.
In normal operating mode, the program cannot disable the
digital PRES circuit. The analog regulator can be disabled,
which also disables the analog portion of the PRES. The PRES
circuit is disabled automatically during sleep and hibernate
modes, with one exception: During sleep mode the regulators
are periodically activated (buzzed) to provide supervisory
services and to reduce wakeup time. At these times the PRES
circuit is also buzzed to allow periodic voltage monitoring.
Page 31 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ ALVI, DLVI, AHVI – Analog/Digital Low Voltage Interrupt,
Analog High Voltage Interrupt
Interrupt circuits are available to detect when VDDA and VDDD
go outside a voltage range. For AHVI, VDDA is compared to a
fixed trip level. For ALVI and DLVI, VDDA and VDDD are
compared to trip levels that are programmable, as listed in
Table 6-5. ALVI and DLVI can also be configured to generate
a device reset instead of an interrupt.
Table 6-5. Analog/Digital Low Voltage Interrupt, Analog High
Voltage Interrupt
Interrupt Supply
Normal
Voltage
Range
Available Trip Accuracy
Settings
DLVI
VDDD
1.71 V to
5.5 V
1.70 V to 5.45 V
in 250 mV
increments
±2%
ALVI
VDDA
1.71 V to
5.5 V
1.70 V to 5.45 V
in 250 mV
increments
±2%
AHVI
VDDA
1.71 V to
5.5 V
5.75 V
±2%
The monitors are disabled until after IPOR. During sleep mode
these circuits are periodically activated (buzzed). If an interrupt
occurs during buzzing then the system first enters its wake up
sequence. The interrupt is then recognized and may be
serviced.
6.3.1.2 Other Reset Sources
„ XRES – External Reset
PSoC 3 has either a single GPIO pin that is configured as an
external reset or a dedicated XRES pin. Either the dedicated
XRES pin or the GPIO pin, if configured, holds the part in reset
while held active (low). The response to an XRES is the same
as to an IPOR reset.
The external reset is active low. It includes an internal pull-up
resistor. XRES is active during sleep and hibernate modes.
„ SRES – Software Reset
A reset can be commanded under program control by setting
a bit in the software reset register. This is done either directly
by the program or indirectly by DMA access. The response to
a SRES is the same as after an IPOR reset.
Another register bit exists to disable this function.
„ WRES – Watchdog Timer Reset
The watchdog reset detects when the software program is no
longer being executed correctly. To indicate to the watchdog
timer that it is running correctly, the program must periodically
reset the timer. If the timer is not reset before a user-specified
amount of time, then a reset is generated.
Note IPOR disables the watchdog function. The program must
enable the watchdog function at an appropriate point in the
code by setting a register bit. When this bit is set, it cannot be
cleared again except by an IPOR power-on reset event.
6.4 I/O System and Routing
PSoC I/Os are extremely flexible. Every GPIO has analog and
digital I/O capability. All I/Os have a large number of drive modes,
which are set at POR. PSoC also provides up to four individual
I/O voltage domains through the VDDIO pins.
There are two types of I/O pins on every device; those with USB
provide a third type. Both General Purpose I/O (GPIO) and
Special I/O (SIO) provide similar digital functionality. The primary
differences are their analog capability and drive strength.
Devices that include USB also provide two USBIO pins that
support specific USB functionality as well as limited GPIO
capability.
All I/O pins are available for use as digital inputs and outputs for
both the CPU and digital peripherals. In addition, all I/O pins can
generate an interrupt. The flexible and advanced capabilities of
the PSoC I/O, combined with any signal to any pin routability,
greatly simplify circuit design and board layout. All GPIO pins can
be used for analog input, CapSense[14], and LCD segment drive,
while SIO pins are used for voltages in excess of VDDA and for
programmable output voltages.
„ Features supported by both GPIO and SIO:
User programmable port reset state
Separate I/O supplies and voltages for up to four groups of I/O
‡ Digital peripherals use DSI to connect the pins
‡ Input or output or both for CPU and DMA
‡ Eight drive modes
‡ Every pin can be an interrupt source configured as rising
edge, falling edge or both edges. If required, level sensitive
interrupts are supported through the DSI
‡ Dedicated port interrupt vector for each port
‡ Slew rate controlled digital output drive mode
‡ Access port control and configuration registers on either port
basis or pin basis
‡ Separate port read (PS) and write (DR) data registers to avoid
read modify write errors
‡ Special functionality on a pin by pin basis
‡
‡
„ Additional features only provided on the GPIO pins:
LCD segment drive on LCD equipped devices
CapSense[14]
‡ Analog input and output capability
‡ Continuous 100 µA clamp current capability
‡ Standard drive strength down to 1.7 V
‡
‡
„ Additional features only provided on SIO pins:
Higher drive strength than GPIO
Hot swap capability (5 V tolerance at any operating VDD)
‡ Programmable and regulated high input and output drive
levels down to 1.2 V
‡ No analog input, CapSense, or LCD capability
‡ Over voltage tolerance up to 5.5 V
‡ SIO can act as a general purpose analog comparator
‡
‡
Note
14. GPIOs with opamp outputs are not recommended for use with CapSense
Document Number: 001-53304 Rev. *K
Page 32 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ USBIO features:
Input, output, or both for digital peripherals
Digital output (CMOS) drive mode
‡ Each pin can be an interrupt source configured as rising
edge, falling edge, or both edges
‡
Full speed USB 2.0 compliant I/O
Highest drive strength for general purpose use
‡ Input, output, or both for CPU and DMA
‡
‡
‡
Figure 6-8. GPIO Block Diagram
Digital Input Path
Naming Convention
‘x’ = Port Number
‘y’ = Pin Number
PRT[x]CTL
PRT[x]DBL_SYNC_IN
PRT[x]PS
Digital System Input
PICU[x]INTTYPE[y]
Input Buffer Disable
PICU[x]INTSTAT
Interrupt
Logic
Pin Interrupt Signal
PICU[x]INTSTAT
Digital Output Path
PRT[x]SLW
PRT[x]SYNC_OUT
Vddio Vddio
PRT[x]DR
0
Digital System Output
In
1
Vddio
PRT[x]BYP
Drive
Logic
PRT[x]DM2
PRT[x]DM1
PRT[x]DM0
Bidirectional Control
PRT[x]BIE
Analog
Slew
Cntl
PIN
OE
1
Capsense Global Control
0
1
0
1
CAPS[x]CFG1
Switches
PRT[x]AG
Analog Global Enable
PRT[x]AMUX
Analog Mux Enable
LCD
Display
Data
PRT[x]LCD_COM_SEG
Logic & MUX
PRT[x]LCD_EN
LCD Bias Bus
Document Number: 001-53304 Rev. *K
5
Page 33 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 6-9. SIO Input/Output Block Diagram
Digital Input Path
PRT[x]SIO_HYST_EN
PRT[x]SIO_DIFF
Reference Level
PRT[x]DBL_SYNC_IN
Naming Convention
‘x’ = Port Number
‘y’ = Pin Number
Buffer
Thresholds
PRT[x]PS
Digital System Input
PICU[x]INTTYPE[y]
Input Buffer Disable
PICU[x]INTSTAT
Interrupt
Logic
Pin Interrupt Signal
PICU[x]INTSTAT
Digital Output Path
Reference Level
PRT[x]SIO_CFG
PRT[x]SLW
PRT[x]SYNC_OUT
PRT[x]DR
Driver
Vhigh
0
Digital System Output
In
1
PRT[x]BYP
Drive
Logic
PRT[x]DM2
PRT[x]DM1
PRT[x]DM0
Bidirectional Control
PRT[x]BIE
Slew
Cntl
PIN
OE
Figure 6-10. USBIO Block Diagram
Digital Input Path
Naming Convention
‘x’ = Port Number
‘y’ = Pin Number
USB Receiver Circuitry
PRT[x]DBL_SYNC_IN
USBIO_CR1[0,1]
Digital System Input
PICU[x]INTTYPE[y]
PICU[x]INTSTAT
Interrupt
Logic
Pin Interrupt Signal
PICU[x]INTSTAT
Digital Output Path
PRT[x]SYNC_OUT
D+ pin only
USBIO_CR1[7]
USB or I/O
USB SIE Control for USB Mode
USBIO_CR1[4,5]
Digital System Output
PRT[x]BYP
Vddd
0
1
In
Drive
Logic
Vddd
5k
Vddd Vddd
1.5 k
PIN
USBIO_CR1[2]
USBIO_CR1[3]
USBIO_CR1[6]
Document Number: 001-53304 Rev. *K
D+ 1.5 k
D+D- 5 k
Open Drain
Page 34 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
if bypass mode is selected. Note that the actual I/O pin voltage
is determined by a combination of the selected drive mode and
the load at the pin. For example, if a GPIO pin is configured for
resistive pull-up mode and driven high while the pin is floating,
the voltage measured at the pin is a high logic state. If the same
GPIO pin is externally tied to ground then the voltage
unmeasured at the pin is a low logic state.
6.4.1 Drive Modes
Each GPIO and SIO pin is individually configurable into one of
the eight drive modes listed in Table 6-6. Three configuration bits
are used for each pin (DM[2:0]) and set in the PRTxDM[2:0]
registers. Figure 6-11 depicts a simplified pin view based on
each of the eight drive modes. Table 6-6 shows the I/O pin’s drive
state based on the port data register value or digital array signal
Figure 6-11. Drive Mode
Vddio
DR
PS
0.
Pin
High Impedance
Analog
DR
PS
Pin
1. High Impedance
Digital
DR
PS
Pin
2. Resistive
Pull-Up
Vddio
DR
PS
Pin
4. Open Drain,
Drives Low
DR
PS
Vddio
DR
PS
Pin
3. Resistive
Pull-Down
Vddio
Pin
5. Open Drain,
Drives High
DR
PS
Vddio
Pin
6. Strong Drive
DR
PS
Pin
7. Resistive
Pull-Up and Pull-Down
Table 6-6. Drive Modes
Diagram
Drive Mode
PRT×DM2
PRT×DM1
PRT×DM0
PRT×DR = 1
PRT×DR = 0
0
High impedence analog
0
0
0
High Z
High Z
1
High Impedance digital
0
0
1
High Z
High Z
pull-up[15]
2
Resistive
0
1
0
Res High (5K)
Strong Low
3
Resistive pull-down[15]
0
1
1
Strong High
Res Low (5K)
4
Open drain, drives low
1
0
0
High Z
Strong Low
5
Open drain, drive high
1
0
1
Strong High
High Z
6
Strong drive
1
1
0
Strong High
Strong Low
7
Resistive pull-up and pull-down[15]
1
1
1
Res High (5K)
Res Low (5K)
To achieve the lowest chip current in sleep modes, all I/Os
must either be configured to the high impedance analog mode,
or have their pins driven to a power supply rail by the PSoC
device or by external circuitry.
„ High impedance analog
The default reset state with both the output driver and digital
input buffer turned off. This prevents any current from flowing
in the I/O’s digital input buffer due to a floating voltage. This
state is recommended for pins that are floating or that support
an analog voltage. High impedance analog pins do not provide
digital input functionality.
„ High impedance digital
The input buffer is enabled for digital signal input. This is the
standard high impedance (High Z) state recommended for
digital inputs.
Note
15. Resistive pull-up and pull-down are not available with SIO in regulated output mode.
Document Number: 001-53304 Rev. *K
Page 35 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Resistive pull-up or resistive pull-down
Resistive pull-up or pull-down, respectively, provides a series
resistance in one of the data states and strong drive in the
other. Pins can be used for digital input and output in these
modes. Interfacing to mechanical switches is a common
application for these modes. Resistive pull-up and pull-down
are not available with SIO in regulated output mode.
„ Open drain, drives high and open drain, drives low
Open drain modes provide high impedance in one of the data
states and strong drive in the other. Pins can be used for digital
input and output in these modes. A common application for
these modes is driving the I2C bus signal lines.
„ Strong drive
Provides a strong CMOS output drive in either high or low
state. This is the standard output mode for pins. Strong Drive
mode pins must not be used as inputs under normal
circumstances. This mode is often used to drive digital output
signals or external FETs.
„ Resistive pull-up and pull-down
Similar to the resistive pull-up and resistive pull-down modes
except the pin is always in series with a resistor. The high data
state is pull-up while the low data state is pull-down. This mode
is most often used when other signals that may cause shorts
can drive the bus. Resistive pull-up and pull-down are not
available with SIO in regulated output mode.
6.4.2 Pin Registers
Registers to configure and interact with pins come in two forms
that may be used interchangeably.
All I/O registers are available in the standard port form, where
each bit of the register corresponds to one of the port pins. This
register form is efficient for quickly reconfiguring multiple port
pins at the same time.
I/O registers are also available in pin form, which combines the
eight most commonly used port register bits into a single register
for each pin. This enables very fast configuration changes to
individual pins with a single register write.
6.4.3 Bidirectional Mode
High-speed bidirectional capability allows pins to provide both
the high impedance digital drive mode for input signals and a
second user selected drive mode such as strong drive (set using
PRT×DM[2:0] registers) for output signals on the same pin,
based on the state of an auxiliary control bus signal. The
bidirectional capability is useful for processor busses and
communications interfaces such as the SPI Slave MISO pin that
requires dynamic hardware control of the output buffer.
The auxiliary control bus routes up to 16 UDB or digital peripheral
generated output enable signals to one or more pins.
6.4.4 Slew Rate Limited Mode
GPIO and SIO pins have fast and slow output slew rate options
for strong and open drain drive modes, not resistive drive modes.
Because it results in reduced EMI, the slow edge rate option is
recommended for signals that are not speed critical, generally
less than 1 MHz. The fast slew rate is for signals between 1 MHz
and 33 MHz. The slew rate is individually configurable for each
pin, and is set by the PRTxSLW registers.
6.4.5 Pin Interrupts
All GPIO and SIO pins are able to generate interrupts to the
system. All eight pins in each port interface to their own Port
Interrupt Control Unit (PICU) and associated interrupt vector.
Each pin of the port is independently configurable to detect rising
edge, falling edge, both edge interrupts, or to not generate an
interrupt.
Depending on the configured mode for each pin, each time an
interrupt event occurs on a pin, its corresponding status bit of the
interrupt status register is set to “1” and an interrupt request is
sent to the interrupt controller. Each PICU has its own interrupt
vector in the interrupt controller and the pin status register
providing easy determination of the interrupt source down to the
pin level.
Port pin interrupts remain active in all sleep modes allowing the
PSoC device to wake from an externally generated interrupt.
While level sensitive interrupts are not directly supported;
Universal Digital Blocks (UDB) provide this functionality to the
system when needed.
6.4.6 Input Buffer Mode
GPIO and SIO input buffers can be configured at the port level
for the default CMOS input thresholds or the optional LVTTL
input thresholds. All input buffers incorporate Schmitt triggers for
input hysteresis. Additionally, individual pin input buffers can be
disabled in any drive mode.
6.4.7 I/O Power Supplies
Up to four I/O pin power supplies are provided depending on the
device and package. Each I/O supply must be less than or equal
to the voltage on the chip’s analog (VDDA) pin. This feature allows
users to provide different I/O voltage levels for different pins on
the device. Refer to the specific device package pinout to
determine VDDIO capability for a given port and pin.
The SIO port pins support an additional regulated high output
capability, as described in Adjustable Output Level.
6.4.8 Analog Connections
These connections apply only to GPIO pins. All GPIO pins may
be used as analog inputs or outputs. The analog voltage present
on the pin must not exceed the VDDIO supply voltage to which
the GPIO belongs. Each GPIO may connect to one of the analog
global busses or to one of the analog mux buses to connect any
pin to any internal analog resource such as ADC or comparators.
In addition, select pins provide direct connections to specific
analog features such as the high current DACs or uncommitted
opamps.
6.4.9 CapSense
This section applies only to GPIO pins. All GPIO pins may be
used to create CapSense buttons and sliders[16]. See the
“CapSense” section on page 59 for more information.
Note
16. GPIOs with opamp outputs are not recommended for use with CapSense
Document Number: 001-53304 Rev. *K
Page 36 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
6.4.10 LCD Segment Drive
This section applies only to GPIO pins. All GPIO pins may be
used to generate Segment and Common drive signals for direct
glass drive of LCD glass. See the “LCD Direct Drive” section on
page 58 for details.
Figure 6-12. SIO Reference for Input and Output
Input Path
Digital
Input
Vinref
6.4.11 Adjustable Output Level
This section applies only to SIO pins. SIO port pins support the
ability to provide a regulated high output level for interface to
external signals that are lower in voltage than the SIO’s
respective Vddio. SIO pins are individually configurable to output
either the standard VDDIO level or the regulated output, which is
based on an internally generated reference. Typically a voltage
DAC (VDAC) is used to generate the reference (see Figure
6-12). The “DAC” section on page 59 has more details on VDAC
use and reference routing to the SIO pins. Resistive pull-up and
pull-down drive modes are not available with SIO in regulated
output mode.
Reference
Generator
SIO_Ref
PIN
Voutref
Output Path
Driver
Vhigh
6.4.12 Adjustable Input Level
This section applies only to SIO pins. SIO pins by default support
the standard CMOS and LVTTL input levels but also support a
differential mode with programmable levels. SIO pins are
grouped into pairs. Each pair shares a reference generator block
which, is used to set the digital input buffer reference level for
interface to external signals that differ in voltage from VDDIO. The
reference sets the pins voltage threshold for a high logic level
(see Figure 6-12). Available input thresholds are:
Digital
Output
Drive
Logic
„ 0.5 × VDDIO
„ 0.4 × VDDIO
6.4.13 SIO as Comparator
„ 0.5 × VREF
This section applies only to SIO pins. The adjustable input level
feature of the SIOs as explained in the Adjustable Input Level
section can be used to construct a comparator. The threshold for
the comparator is provided by the SIO's reference generator. The
reference generator has the option to set the analog signal
routed through the analog global line as threshold for the
comparator. Note that a pair of SIO pins share the same
threshold.
„ VREF
Typically a voltage DAC (VDAC) generates the VREF reference.
“DAC” section on page 59 has more details on VDAC use and
reference routing to the SIO pins.
The digital input path in Figure 6-9 on page 34 illustrates this
functionality. In the figure, ‘Reference level’ is the analog signal
routed through the analog global. The hysteresis feature can
also be enabled for the input buffer of the SIO, which increases
noise immunity for the comparator.
6.4.14 Hot Swap
This section applies only to SIO pins. SIO pins support ‘hot swap’
capability to plug into an application without loading the signals
that are connected to the SIO pins even when no power is
applied to the PSoC device. This allows the unpowered PSoC to
maintain a high impedance load to the external device while also
preventing the PSoC from being powered through a GPIO pin’s
protection diode.
Document Number: 001-53304 Rev. *K
Page 37 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
6.4.15 Over Voltage Tolerance
‡
All I/O pins provide an over voltage tolerance feature at any
operating VDD.
‡
„ There are no current limitations for the SIO pins as they present a
high impedance load to the external circuit where Vddio < VIN <
5.5 V.
High current IDAC outputs
External reference inputs
6.4.19 JTAG Boundary Scan
The device supports standard JTAG boundary scan chains on all
I/O pins for board level test.
„ The GPIO pins must be limited to 100 µA using a current limiting
7. Digital Subsystem
„ In case of a GPIO pin configured for analog input/output, the
The digital programmable system creates application specific
combinations of both standard and advanced digital peripherals
and custom logic functions. These peripherals and logic are then
interconnected to each other and to any pin on the device,
providing a high level of design flexibility and IP security.
resistor. GPIO pins clamp the pin voltage to approximately one
diode above the Vddio supply where Vddio < VIN < VDDA.
analog voltage on the pin must not exceed the Vddio supply
voltage to which the GPIO belongs.
A common application for this feature is connection to a bus such
as I2C where different devices are running from different supply
voltages. In the I2C case, the PSoC chip is configured into the
Open Drain, Drives Low mode for the SIO pin. This allows an
external pull-up to pull the I2C bus voltage above the PSoC pin
supply. For example, the PSoC chip could operate at 1.8 V, and
an external device could run from 5 V. Note that the SIO pin’s VIH
and VIL levels are determined by the associated Vddio supply
pin.
The features of the digital programmable system are outlined
here to provide an overview of capabilities and architecture. You
do not need to interact directly with the programmable digital
system at the hardware and register level. PSoC Creator
provides a high level schematic capture graphical interface to
automatically place and route resources similar to PLDs.
The I/O pin must be configured into a high impedance drive
mode, open drain low drive mode, or pull-down drive mode, for
over voltage tolerance to work properly. Absolute maximum
ratings for the device must be observed for all I/O pins.
functionality of the digital programmable system. UDBs are a
collection of uncommitted logic (PLD) and structural logic
(Datapath) optimized to create all common embedded
peripherals and customized functionality that are application or
design specific.
6.4.18 Special Pin Functionality
Some pins on the device include additional special functionality
in addition to their GPIO or SIO functionality. The specific special
function pins are listed in Pinouts on page 5. The special features
are:
„ Digital System Interconnect (DSI) – Digital signals from
Universal Digital Blocks (UDBs), fixed function peripherals, I/O
pins, interrupts, DMA, and other system core signals are
attached to the Digital System Interconnect to implement full
featured device connectivity. The DSI allows any digital function
to any pin or other feature routability when used with the
Universal Digital Block Array.
Figure 7-1. CY8C34 Digital Programmable Architecture
Digital Core System
and Fixed Function Peripherals
DSI Routing Interface
„ Digital
4 to 25 MHz crystal oscillator
‡ 32.768-kHz crystal oscillator
2
‡ Wake from sleep on I C address match. Any pin can be used
for I2C if wake from sleep is not required.
‡ JTAG interface pins
‡ SWD interface pins
‡ SWV interface pins
‡ External reset
‡
Opamp inputs and outputs
Document Number: 001-53304 Rev. *K
IO Port
UDB Array
‡
„ Analog
IO Port
In all low-power modes the I/O pins retain their state until the part
is awakened and changed or reset. To awaken the part, use a
pin interrupt, because the port interrupt logic continues to
function in all low-power modes.
a matrix of programmable interconnect. The UDB array
structure is homogeneous and allows for flexible mapping of
digital functions onto the array. The array supports extensive
and flexible routing interconnects between UDBs and the
Digital System Interconnect.
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
DSI Routing Interface
Digital Core System
and Fixed Function Peripherals
IO Port
6.4.17 Low-Power Functionality
„ Universal Digital Block Array – UDB blocks are arrayed within
UDB Array
While reset is active all I/Os are reset to and held in the High
Impedance Analog state. After reset is released, the state can be
reprogrammed on a port-by-port basis to pull-down or pull-up. To
ensure correct reset operation, the port reset configuration data
is stored in special nonvolatile registers. The stored reset data is
automatically transferred to the port reset configuration registers
at reset release.
„ Universal Digital Blocks (UDB) – These form the core
IO Port
6.4.16 Reset Configuration
The main components of the digital programmable system are:
Page 38 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
7.1 Example Peripherals
‡
The flexibility of the CY8C34 family’s Universal Digital Blocks
(UDBs) and Analog Blocks allow the user to create a wide range
of components (peripherals). The most common peripherals
were built and characterized by Cypress and are shown in the
PSoC Creator component catalog, however, users may also
create their own custom components using PSoC Creator. Using
PSoC Creator, users may also create their own components for
reuse within their organization, for example sensor interfaces,
proprietary algorithms, and display interfaces.
‡
The number of components available through PSoC Creator is
too numerous to list in the data sheet, and the list is always
growing. An example of a component available for use in
CY8C34 family, but, not explicitly called out in this data sheet is
the UART component.
7.1.1 Example Digital Components
The following is a sample of the digital components available in
PSoC Creator for the CY8C34 family. The exact amount of
hardware resources (UDBs, routing, RAM, flash) used by a
component varies with the features selected in PSoC Creator for
the component.
„ Communications
I2C
UART
‡ SPI
‡
‡
„ Functions
EMIF
PWMs
‡ Timers
‡ Counters
‡
‡
„ Logic
NOT
OR
‡ XOR
‡ AND
‡
‡
7.1.2 Example Analog Components
The following is a sample of the analog components available in
PSoC Creator for the CY8C34 family. The exact amount of
hardware resources (SC/CT blocks, routing, RAM, flash) used
by a component varies with the features selected in PSoC
Creator for the component.
„ Amplifiers
TIA
PGA
‡ opamp
‡
‡
„ ADC
‡
Delta-Sigma
„ DACs
‡
Voltage
PWM
„ Comparators
„ Mixers
7.1.3 Example System Function Components
The following is a sample of the system function components
available in PSoC Creator for the CY8C34 family. The exact
amount of hardware resources (UDBs, SC/CT blocks, routing,
RAM, flash) used by a component varies with the features
selected in PSoC Creator for the component.
„ CapSense
„ LCD Drive
„ LCD Control
7.1.4 Designing with PSoC Creator
7.1.4.1 More Than a Typical IDE
A successful design tool allows for the rapid development and
deployment of both simple and complex designs. It reduces or
eliminates any learning curve. It makes the integration of a new
design into the production stream straightforward.
PSoC Creator is that design tool.
PSoC Creator is a full featured Integrated Development
Environment (IDE) for hardware and software design. It is
optimized specifically for PSoC devices and combines a modern,
powerful software development platform with a sophisticated
graphical design tool. This unique combination of tools makes
PSoC Creator the most flexible embedded design platform
available.
Graphical design entry simplifies the task of configuring a
particular part. You can select the required functionality from an
extensive catalog of components and place it in your design. All
components are parameterized and have an editor dialog that
allows you to tailor functionality to your needs.
PSoC Creator automatically configures clocks and routes the I/O
to the selected pins and then generates APIs to give the
application complete control over the hardware. Changing the
PSoC device configuration is as simple as adding a new
component, setting its parameters, and rebuilding the project.
At any stage of development you are free to change the
hardware configuration and even the target processor. To
retarget your application (hardware and software) to new
devices, even from 8- to 32-bit families, just select the new
device and rebuild.
You also have the ability to change the C compiler and evaluate
an alternative. Components are designed for portability and are
validated against all devices, from all families, and against all
supported tool chains. Switching compilers is as easy as editing
the from the project options and rebuilding the application with
no errors from the generated APIs or boot code.
Current
Document Number: 001-53304 Rev. *K
Page 39 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 7-2. PSoC Creator Framework
Document Number: 001-53304 Rev. *K
Page 40 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
7.1.4.2 Component Catalog
7.1.4.4 Software Development
Figure 7-3. Component Catalog
Figure 7-4. Code Editor
Anchoring the tool is a modern, highly customizable user
interface. It includes project management and integrated editors
for C and assembler source code, as well the design entry tools.
The component catalog is a repository of reusable design
elements that select device functionality and customize your
PSoC device. It is populated with an impressive selection of
content; from simple primitives such as logic gates and device
registers, through the digital timers, counters and PWMs, plus
analog components such as ADC, DACs, and filters, and
communication protocols, such as I2C, USB, and CAN. See
Example Peripherals on page 39 for more details about available
peripherals. All content is fully characterized and carefully
documented in data sheets with code examples, AC/DC
specifications, and user code ready APIs.
Project build control leverages compiler technology from top
commercial vendors such as ARM® Limited, Keil™, and
CodeSourcery (GNU). Free versions of Keil C51 and GNU C
Compiler (GCC) for ARM, with no restrictions on code size or end
product distribution, are included with the tool distribution.
Upgrading to more optimizing compilers is a snap with support
for the professional Keil C51 product and ARM RealView™
compiler.
7.1.4.5 Nonintrusive Debugging
Figure 7-5. PSoC Creator Debugger
7.1.4.3 Design Reuse
The symbol editor gives you the ability to develop reusable
components that can significantly reduce future design time. Just
draw a symbol and associate that symbol with your proven
design. PSoC Creator allows for the placement of the new
symbol anywhere in the component catalog along with the
content provided by Cypress. You can then reuse your content
as many times as you want, and in any number of projects,
without ever having to revisit the details of the implementation.
With JTAG (4-wire) and SWD (2-wire) debug connectivity
available on all devices, the PSoC Creator debugger offers full
control over the target device with minimum intrusion.
Breakpoints and code execution commands are all readily
available from toolbar buttons and an impressive lineup of
windows—register, locals, watch, call stack, memory and
peripherals—make for an unparalleled level of visibility into the
system.
Document Number: 001-53304 Rev. *K
Page 41 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Clock and Reset Module – This block provides the UDB clocks
and reset selection and control.
7.2.1 PLD Module
The primary purpose of the PLD blocks is to implement logic
expressions, state machines, sequencers, lookup tables, and
decoders. In the simplest use model, consider the PLD blocks as
a standalone resource onto which general purpose RTL is
synthesized and mapped. The more common and efficient use
model is to create digital functions from a combination of PLD
and datapath blocks, where the PLD implements only the
random logic and state portion of the function while the datapath
(ALU) implements the more structured elements.
PT4
PT5
PT6
PT7
Figure 7-7. PLD 12C4 Structure
PT3
To achieve this, UDBs consist of a combination of uncommitted
logic (PLD), structured logic (Datapath), and a flexible routing
scheme to provide interconnect between these elements, I/O
connections, and other peripherals. UDB functionality ranges
from simple self contained functions that are implemented in one
UDB, or even a portion of a UDB (unused resources are
available for other functions), to more complex functions that
require multiple UDBs. Examples of basic functions are timers,
counters, CRC generators, PWMs, dead band generators, and
communications functions, such as UARTs, SPI, and I2C. Also,
the PLD blocks and connectivity provide full featured general
purpose programmable logic within the limits of the available
resources.
to provide a way for CPU firmware to interact and synchronize
with UDB operation.
PT2
The Universal Digital Block (UDB) represents an evolutionary
step to the next generation of PSoC embedded digital peripheral
functionality. The architecture in first generation PSoC digital
blocks provides coarse programmability in which a few fixed
functions with a small number of options are available. The new
UDB architecture is the optimal balance between configuration
granularity and efficient implementation. A cornerstone of this
approach is to provide the ability to customize the devices digital
operation to match application requirements.
„ Status and Control Module – The primary role of this block is
PT1
7.2 Universal Digital Block
also contains input/output FIFOs, which are the primary parallel
data interface between the CPU/DMA system and the UDB.
PT0
PSoC Creator contains all the tools necessary to complete a
design, and then to maintain and extend that design for years to
come. All steps of the design flow are carefully integrated and
optimized for ease-of-use and to maximize productivity.
IN0
TC
TC
TC
TC
TC
TC
TC
TC
IN1
TC
TC
TC
TC
TC
TC
TC
TC
IN2
TC
TC
TC
TC
TC
TC
TC
TC
IN3
TC
TC
TC
TC
TC
TC
TC
TC
IN4
TC
TC
TC
TC
TC
TC
TC
TC
IN5
TC
TC
TC
TC
TC
TC
TC
TC
IN6
TC
TC
TC
TC
TC
TC
TC
TC
IN7
TC
TC
TC
TC
TC
TC
TC
TC
IN8
TC
TC
TC
TC
TC
TC
TC
TC
IN9
TC
TC
TC
TC
TC
TC
TC
TC
IN10
TC
TC
TC
TC
TC
TC
TC
TC
IN11
TC
TC
TC
TC
TC
TC
TC
TC
Figure 7-6. UDB Block Diagram
PLD
Chaining
Clock
and Reset
Control
Status and
Control
PLD
12C4
(8 PTs)
PLD
12C4
(8 PTs)
Datapath
Datapath
Chaining
SELIN
(carry in)
OUT0
MC0
T
T
T
T
T
T
T
T
OUT1
MC1
T
T
T
T
T
T
T
T
OUT2
MC2
T
T
T
T
T
T
T
T
OUT3
MC3
T
T
T
T
T
T
T
T
SELOUT
(carry out)
Routing Channel
The main component blocks of the UDB are:
„ PLD blocks – There are two small PLDs per UDB. These blocks
take inputs from the routing array and form registered or
combinational sum-of-products logic. PLDs are used to
implement state machines, state bits, and combinational logic
equations. PLD configuration is automatically generated from
graphical primitives.
„ Datapath Module – This 8-bit wide datapath contains structured
logic to implement a dynamically configurable ALU, a variety
of compare configurations and condition generation. This block
Document Number: 001-53304 Rev. *K
AND
Array
OR
Array
One 12C4 PLD block is shown in Figure 7-7. This PLD has 12
inputs, which feed across eight product terms. Each product term
(AND function) can be from 1 to 12 inputs wide, and in a given
product term, the true (T) or complement (C) of each input can
be selected. The product terms are summed (OR function) to
create the PLD outputs. A sum can be from 1 to 8 product terms
wide. The 'C' in 12C4 indicates that the width of the OR gate (in
this case 8) is constant across all outputs (rather than variable
as in a 22V10 device). This PLA like structure gives maximum
flexibility and insures that all inputs and outputs are permutable
for ease of allocation by the software tools. There are two 12C4
PLDs in each UDB.
Page 42 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
7.2.2 Datapath Module
The datapath contains an 8-bit single cycle ALU, with associated compare and condition generation logic. This datapath block is
optimized to implement embedded functions, such as timers, counters, integrators, PWMs, PRS, CRC, shifters and dead band
generators and many others.
Figure 7-8. Datapath Top Level
PHUB System Bus
R/W Access to All
Registers
F1
F0
D1
Data Registers
A0
A1
D0
D1
D0
To/From
Previous
Datapath
A1
Conditions: 2 Compares,
2 Zero Detect, 2 Ones
Detect Overflow Detect
6
Datapath Control
Input from
Programmable
Routing
Control Store RAM
8 Word X 16 Bit
FIFOs
Input
Muxes
Chaining
Output
Muxes
6
Output to
Programmable
Routing
To/From
Next
Datapath
Accumulators
A0
PI
Parallel Input/Output
(To/From Programmable Routing)
PO
ALU
Shift
Mask
7.2.2.1 Working Registers
7.2.2.2 Dynamic Datapath Configuration RAM
The datapath contains six primary working registers, which are
accessed by CPU firmware or DMA during normal operation.
Dynamic configuration is the ability to change the datapath
function and internal configuration on a cycle-by-cycle basis,
under sequencer control. This is implemented using the 8-word
× 16-bit configuration RAM, which stores eight unique 16-bit
wide configurations. The address input to this RAM controls the
sequence, and can be routed from any block connected to the
UDB routing matrix, most typically PLD logic, I/O pins, or from
the outputs of this or other datapath blocks.
Table 7-1. Working Datapath Registers
Name
Function
Description
A0 and A1 Accumulators
These are sources and sinks for
the ALU and also sources for the
compares.
D0 and D1 Data Registers
These are sources for the ALU
and sources for the compares.
F0 and F1
These are the primary interface to
the system bus. They can be a
data source for the data registers
and accumulators or they can
capture data from the accumulators or ALU. Each FIFO is four
bytes deep.
FIFOs
Document Number: 001-53304 Rev. *K
ALU
The ALU performs eight general purpose functions. They are:
„ Increment
„ Decrement
„ Add
„ Subtract
„ Logical AND
Page 43 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Logical OR
„ Logical XOR
Figure 7-9. Example FIFO Configurations
System Bus
System Bus
„ Pass, used to pass a value through the ALU to the shift register,
mask, or another UDB register
F0
F0
F1
D0
A0
D1
A1
Independent of the ALU operation, these functions are available:
„ Shift left
D0/D1
A0/A1/ALU
A0/A1/ALU
A0/A1/ALU
F1
F0
F1
„ Shift right
„ Nibble swap
„ Bitwise OR mask
7.2.2.3 Conditionals
Each datapath has two compares, with bit masking options.
Compare operands include the two accumulators and the two
data registers in a variety of configurations. Other conditions
include zero detect, all ones detect, and overflow. These
conditions are the primary datapath outputs, a selection of which
can be driven out to the UDB routing matrix. Conditional
computation can use the built in chaining to neighboring UDBs
to operate on wider data widths without the need to use routing
resources.
7.2.2.4 Variable MSB
The most significant bit of an arithmetic and shift function can be
programmatically specified. This supports variable width CRC
and PRS functions, and in conjunction with ALU output masking,
can implement arbitrary width timers, counters and shift blocks.
7.2.2.5 Built in CRC/PRS
The datapath has built in support for single cycle Cyclic
Redundancy Check (CRC) computation and Pseudo Random
Sequence (PRS) generation of arbitrary width and arbitrary
polynomial. CRC/PRS functions longer than 8 bits may be
implemented in conjunction with PLD logic, or built in chaining
may be use to extend the function into neighboring UDBs.
7.2.2.6 Input/Output FIFOs
Each datapath contains two four-byte deep FIFOs, which can be
independently configured as an input buffer (system bus writes
to the FIFO, datapath internal reads the FIFO), or an output
buffer (datapath internal writes to the FIFO, the system bus reads
from the FIFO). The FIFOs generate status that are selectable
as datapath outputs and can therefore be driven to the routing,
to interact with sequencers, interrupts, or DMA.
System Bus
System Bus
TX/RX
Dual Capture
Dual Buffer
7.2.2.7 Chaining
The datapath can be configured to chain conditions and signals
such as carries and shift data with neighboring datapaths to
create higher precision arithmetic, shift, CRC/PRS functions.
7.2.2.8 Time Multiplexing
In applications that are over sampled, or do not need high clock
rates, the single ALU block in the datapath can be efficiently
shared with two sets of registers and condition generators. Carry
and shift out data from the ALU are registered and can be
selected as inputs in subsequent cycles. This provides support
for 16-bit functions in one (8-bit) datapath.
7.2.2.9 Datapath I/O
There are six inputs and six outputs that connect the datapath to
the routing matrix. Inputs from the routing provide the
configuration for the datapath operation to perform in each cycle,
and the serial data inputs. Inputs can be routed from other UDB
blocks, other device peripherals, device I/O pins, and so on. The
outputs to the routing can be selected from the generated
conditions, and the serial data outputs. Outputs can be routed to
other UDB blocks, device peripherals, interrupt and DMA
controller, I/O pins, and so on.
7.2.3 Status and Control Module
The primary purpose of this circuitry is to coordinate CPU
firmware interaction with internal UDB operation.
Figure 7-10. Status and Control Registers
System Bus
8-bit Status Register
(Read Only)
8-bit Control Register
(Write/Read)
Routing Channel
The bits of the control register, which may be written to by the
system bus, are used to drive into the routing matrix, and thus
provide firmware with the opportunity to control the state of UDB
processing. The status register is read-only and it allows internal
Document Number: 001-53304 Rev. *K
Page 44 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
UDB state to be read out onto the system bus directly from
internal routing. This allows firmware to monitor the state of UDB
processing. Each bit of these registers has programmable
connections to the routing matrix and routing connections are
made depending on the requirements of the application.
Figure 7-11. Digital System Interface Structure
System Connections
HV
B
7.2.3.1 Usage Examples
As an example of control input, a bit in the control register can
be allocated as a function enable bit. There are multiple ways to
enable a function. In one method the control bit output would be
routed to the clock control block in one or more UDBs and serve
as a clock enable for the selected UDB blocks. A status example
is a case where a PLD or datapath block generated a condition,
such as a “compare true” condition that is captured and latched
by the status register and then read (and cleared) by CPU
firmware.
7.2.3.2 Clock Generation
Each subcomponent block of a UDB including the two PLDs, the
datapath, and Status and Control, has a clock selection and
control block. This promotes a fine granularity with respect to
allocating clocking resources to UDB component blocks and
allows unused UDB resources to be used by other functions for
maximum system efficiency.
7.3 UDB Array Description
Figure 7-11 shows an example of a 16 UDB array. In addition to
the array core, there are a DSI routing interfaces at the top and
bottom of the array. Other interfaces that are not explicitly shown
include the system interfaces for bus and clock distribution. The
UDB array includes multiple horizontal and vertical routing
channels each comprised of 96 wires. The wire connections to
UDBs, at horizontal/vertical intersection and at the DSI interface
are highly permutable providing efficient automatic routing in
PSoC Creator. Additionally the routing allows wire by wire
segmentation along the vertical and horizontal routing to further
increase routing flexibility and capability.
UDB
HV
A
UDB
HV
A
HV
B
UDB
HV
B
HV
A
UDB
HV
A
HV
B
UDB
UDB
UDB
UDB
UDB
UDB
UDB
UDB
HV
B
UDB
HV
A
UDB
HV
A
HV
B
UDB
HV
B
HV
A
UDB
HV
A
HV
B
System Connections
7.3.1 UDB Array Programmable Resources
Figure 7-12 shows an example of how functions are mapped into
a bank of 16 UDBs. The primary programmable resources of the
UDB are two PLDs, one datapath and one status/control register.
These resources are allocated independently, because they
have independently selectable clocks, and therefore unused
blocks are allocated to other unrelated functions.
An example of this is the 8-bit Timer in the upper left corner of
the array. This function only requires one datapath in the UDB,
and therefore the PLD resources may be allocated to another
function. A function such as a Quadrature Decoder may require
more PLD logic than one UDB can supply and in this case can
utilize the unused PLD blocks in the 8-bit Timer UDB.
Programmable resources in the UDB array are generally
homogeneous so functions can be mapped to arbitrary
boundaries in the array.
Document Number: 001-53304 Rev. *K
Page 45 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 7-12. Function Mapping Example in a Bank of UDBs
8-Bit
Timer
UDB
Sequencer
Quadrature Decoder
UDB
HV
A
16-Bit
PWM
HV
B
Timer
Counters
16-Bit PYRS
UDB
Figure 7-13. Digital System Interconnect
CAN
Interrupt
Controller
I2C
DMA
Controller
IO Port
Pins
Global
Clocks
UDB
HV
A
HV
B
Digital System Routing I/F
UDB
UDB
UDB
8-Bit
Timer Logic
UDB
8-Bit SPI
I2C Slave
UDB ARRAY
12-Bit SPI
UDB
UDB
UDB
UDB
Digital System Routing I/F
HV
B
HV
A
HV
B
HV
A
Logic
UDB
UDB
UART
UDB
UDB
12-Bit PWM
7.4 DSI Routing Interface Description
The DSI routing interface is a continuation of the horizontal and
vertical routing channels at the top and bottom of the UDB array
core. It provides general purpose programmable routing
between device peripherals, including UDBs, I/Os, analog
peripherals, interrupts, DMA and fixed function peripherals.
Figure 7-13 illustrates the concept of the digital system
interconnect, which connects the UDB array routing matrix with
other device peripherals. Any digital core or fixed function
peripheral that needs programmable routing is connected to this
interface.
Signals in this category include:
Global
Clocks
IO Port
Pins
EMIF
Del-Sig
SC/CT
Blocks
DACs
Interrupt and DMA routing is very flexible in the CY8C34
programmable architecture. In addition to the numerous fixed
function peripherals that can generate interrupt requests, any
data signal in the UDB array routing can also be used to generate
a request. A single peripheral may generate multiple
independent interrupt requests simplifying system and firmware
design. Figure 7-14 shows the structure of the IDMUX
(Interrupt/DMA Multiplexer).
Figure 7-14. Interrupt and DMA Processing in the IDMUX
Interrupt and DMA Processing in IDMUX
Fixed Function IRQs
0
„ Interrupt requests from all digital peripherals in the system.
1
„ DMA requests from all digital peripherals in the system.
IRQs
„ Digital peripheral data signals that need flexible routing to I/Os.
UDB Array
„ Digital peripheral data signals that need connections to UDBs.
2
Edge
Detect
Interrupt
Controller
3
DRQs
DMA termout (IRQs)
„ Connections to the interrupt and DMA controllers.
„ Connection to I/O pins.
Comparators
0
Fixed Function DRQs
„ Connection to analog system digital signals.
1
Edge
Detect
DMA
Controller
2
7.4.1 I/O Port Routing
There are a total of 20 DSI routes to a typical 8-bit I/O port, 16
for data and four for drive strength control.
When an I/O pin is connected to the routing, there are two
primary connections available, an input and an output. In
conjunction with drive strength control, this can implement a
bidirectional I/O pin. A data output signal has the option to be
single synchronized (pipelined) and a data input signal has the
Document Number: 001-53304 Rev. *K
Page 46 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
option to be double synchronized. The synchronization clock is
the system clock (see Figure 6-1). Normally all inputs from pins
are synchronized as this is required if the CPU interacts with the
signal or any signal derived from it. Asynchronous inputs have
rare uses. An example of this is a feed through of combinational
PLD logic from input pins to output pins.
The output enable signal is useful for creating tri-state
bidirectional pins and buses.
Figure 7-17. I/O Pin Output Enable Connectivity
4 IO Control Signal Connections from
UDB Array Digital System Interface
Figure 7-15. I/O Pin Synchronization Routing
DO
DI
OE
PIN 0
Figure 7-16. I/O Pin Output Connectivity
OE
PIN1
OE
PIN2
OE
PIN3
OE
PIN4
OE
PIN5
OE
PIN6
OE
PIN7
8 IO Data Output Connections from the
UDB Array Digital System Interface
Port i
7.5 CAN
DO
PIN 0
DO
PIN1
DO
PIN2
DO
PIN3
DO
PIN4
DO
PIN5
DO
PIN6
DO
PIN7
Port i
There are four more DSI connections to a given I/O port to
implement dynamic output enable control of pins. This
connectivity gives a range of options, from fully ganged 8-bits
controlled by one signal, to up to four individually controlled pins.
The CAN peripheral is a fully functional Controller Area Network
(CAN) supporting communication baud rates up to 1 Mbps. The
CAN controller implements the CAN2.0A and CAN2.0B
specifications as defined in the Bosch specification and
conforms to the ISO-11898-1 standard. The CAN protocol was
originally designed for automotive applications with a focus on a
high level of fault detection. This ensures high communication
reliability at a low cost. Because of its success in automotive
applications, CAN is used as a standard communication protocol
for motion oriented machine control networks (CANOpen) and
factory automation applications (DeviceNet). The CAN controller
features allow the efficient implementation of higher level
protocols without affecting the performance of the
microcontroller CPU. Full configuration support is provided in
PSoC Creator.
Figure 7-18. CAN Bus System Implementation
CAN Node 1
CAN Node 2
CAN Node n
PSoC
CAN
Drivers
CAN Controller
En
Tx Rx
CAN Transceiver
CAN_H
CAN_L
CAN_H
CAN_L
CAN_H
CAN_L
CAN Bus
Document Number: 001-53304 Rev. *K
Page 47 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
„ Receive path
7.5.1 CAN Features
„ CAN2.0A/B protocol implementation – ISO 11898 compliant
Standard and extended frames with up to 8 bytes of data per
frame
‡ Message filter capabilities
‡ Remote Transmission Request (RTR) support
‡ Programmable bit rate up to 1 Mbps
‡
„ Listen Only mode
16 receive buffers each with its own message filter
Enhanced hardware message filter implementation that
covers the ID, IDE and RTR
‡ DeviceNet addressing support
‡ Multiple receive buffers linkable to build a larger receive
message array
‡ Automatic transmission request (RTR) response handler
‡ Lost received message notification
‡
‡
„ Transmit path
„ SW readable error counter and indicator
„ Sleep mode: Wake the device from sleep with activity on the
Rx pin
„ Supports two or three wire interface to external transceiver (Tx,
Rx, and Enable). The three-wire interface is compatible with
the Philips PHY; the PHY is not included on-chip. The three
wires can be routed to any I/O
Eight transmit buffers
Programmable transmit priority
• Round robin
• Fixed priority
‡ Message transmissions abort capability
‡
‡
7.5.2 Software Tools Support
CAN Controller configuration integrated into PSoC Creator:
„ Enhanced interrupt controller
CAN receive and transmit buffers status
‡ CAN controller error status including BusOff
‡
„ CAN Configuration walkthrough with bit timing analyzer
„ Receive filter setup
Figure 7-19. CAN Controller Block Diagram
TxMessage0
TxReq
TxAbort
Tx Buffer
Status
TxReq
Pending
TxMessage1
TxReq
TxAbort
Bit Timing
Priority
Arbiter
TxMessage6
TxReq
TxAbort
TxInterrupt
Request
(if enabled)
TxMessage7
TxReq
TxAbort
RxInterrupt
Request
(if enabled)
RxMessage0
Acceptance Code 0
Acceptance Mask 0
RxMessage1
Acceptance Code 1
Acceptance Mask 1
RxMessage
Handler
RxMessage14
Acceptance Code 14
Acceptance Mask 14
RxMessage15
Acceptance Code 15
Acceptance Mask 15
ErrInterrupt
Request
(if enabled)
Document Number: 001-53304 Rev. *K
Tx
CRC
Generator
Error Status
Error Active
Error Passive
Bus Off
Tx Error Counter
Rx Error Counter
RTR RxMessages
0-15
Rx Buffer
Status
RxMessage
Available
Tx
CAN
Framer
Rx
CAN
Framer
Rx
CRC Check
Error Detection
CRC
Form
ACK
Bit Stuffing
Bit Error
Overload
Arbitration
WakeUp
Request
Page 48 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
7.6 USB
PSoC includes a dedicated Full-Speed (12 Mbps) USB 2.0
transceiver supporting all four USB transfer types: control,
interrupt, bulk, and isochronous. PSoC Creator provides full
configuration support. USB interfaces to hosts through two
dedicated USBIO pins, which are detailed in the “I/O System and
Routing” section on page 32.
USB includes the following features:
to any device pin and any internal digital signal accessible
through the DSI. Each of the four instances has a compare
output, terminal count output (optional complementary compare
output), and programmable interrupt request line. The
Timer/Counter/PWMs are configurable as free running, one shot,
or Enable input controlled. The peripheral has timer reset and
capture inputs, and a kill input for control of the comparator
outputs. The peripheral supports full 16-bit capture.
Timer/Counter/PWM features include:
„ Eight unidirectional data endpoints
„ 16-bit Timer/Counter/PWM (down count only)
„ One bidirectional control endpoint 0 (EP0)
„ Shared 512-byte buffer for the eight data endpoints
„ Dedicated 8-byte buffer for EP0
„ Selectable clock source
„ PWM comparator (configurable for LT, LTE, EQ, GTE, GT)
„ Period reload on start, reset, and terminal count
„ Three memory modes
Manual Memory Management with No DMA Access
‡ Manual Memory Management with Manual DMA Access
‡ Automatic Memory Management with Automatic DMA
Access
‡
„ Interrupt on terminal count, compare true, or capture
„ Dynamic counter reads
„ Timer capture mode
„ Internal 3.3-V regulator for transceiver
„ Count while enable signal is asserted mode
„ Internal 48 MHz main oscillator mode that auto locks to USB
„ Free run mode
bus clock, requiring no external crystal for USB (USB equipped
parts only)
„ Interrupts on bus and each endpoint event, with device wakeup
„ USB Reset, Suspend, and Resume operations
System Bus
512 X 8
SRAM
D+
External 22 Ω
Resistors
USB
I/O
Interrupts
D–
48 MHz
IMO
7.7 Timers, Counters, and PWMs
The Timer/Counter/PWM peripheral is a 16-bit dedicated
peripheral providing three of the most common embedded
peripheral features. As almost all embedded systems use some
combination of timers, counters, and PWMs. Four of them have
been included on this PSoC device family. Additional and more
advanced functionality timers, counters, and PWMs can also be
instantiated in Universal Digital Blocks (UDBs) as required.
PSoC Creator allows you to choose the timer, counter, and PWM
features that they require. The tool set utilizes the most optimal
resources available.
The Timer/Counter/PWM peripheral can select from multiple
clock sources, with input and output signals connected through
the DSI routing. DSI routing allows input and output connections
Document Number: 001-53304 Rev. *K
„ PWM output kill
Clock
Reset
Enable
Capture
Kill
Figure 7-20. USB
SIE
(Serial Interface
Engine)
„ Complementary PWM outputs with deadband
Figure 7-21. Timer/Counter/PWM
„ Bus powered and self powered modes
Arbiter
„ One Shot mode (stop at end of period)
Timer / Counter /
PWM 16-bit
IRQ
TC / Compare!
Compare
7.8 I2C
The I2C peripheral provides a synchronous two wire interface
designed to interface the PSoC device with a two wire I2C serial
communication bus. The bus is compliant with Philips ‘The I2C
Specification’ version 2.1. Additional I2C interfaces can be
instantiated using Universal Digital Blocks (UDBs) in PSoC
Creator, as required.
To eliminate the need for excessive CPU intervention and
overhead, I2C specific support is provided for status detection
and generation of framing bits. I2C operates as a slave, a master,
or multimaster (Slave and Master). In slave mode, the unit
always listens for a start condition to begin sending or receiving
data. Master mode supplies the ability to generate the Start and
Stop conditions and initiate transactions. Multimaster mode
provides clock synchronization and arbitration to allow multiple
masters on the same bus. If Master mode is enabled and Slave
mode is not enabled, the block does not generate interrupts on
externally generated Start conditions. I2C interfaces through DSI
routing and allows direct connections to any GPIO or SIO pins.
I2C provides hardware address detect of a 7-bit address without
CPU intervention. Additionally the device can wake from
low-power modes on a 7-bit hardware address match. If wakeup
functionality is required, I2C pin connections are limited to the
two special sets of SIO pins.
Page 49 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
I2C features include:
„ SMBus operation (through firmware support – SMBus
supported in hardware in UDBs)
„ Slave and Master, Transmitter, and Receiver operation
„ 7-bit hardware address compare
„ Byte processing for low CPU overhead
„ Wake from low-power modes on address match
Data transfers follow the format shown in Figure 7-22. After the
START condition (S), a slave address is sent. This address is 7
bits long followed by an eighth bit which is a data direction bit
(R/W) - a 'zero' indicates a transmission (WRITE), a 'one'
indicates a request for data (READ). A data transfer is always
terminated by a STOP condition (P) generated by the master.
However, if a master still wishes to communicate on the bus, it
can generate a repeated START condition (Sr) and address
another slave without first generating a STOP condition. Various
combinations of read/write formats are then possible within such
a transfer.
„ Interrupt or polling CPU interface
„ Support for bus speeds up to 1 Mbps (3.4 Mbps in UDBs)
„ 7 or 10-bit addressing (10-bit addressing requires firmware
support)
Figure 7-22. I2C Complete Transfer Timing
SDA
1-7
SCL
START
Condition
ADDRESS
8
9
R/W
ACK
1-7
8
DATA
8. Analog Subsystem
The analog programmable system creates application specific
combinations of both standard and advanced analog signal
processing blocks. These blocks are then interconnected to
each other and also to any pin on the device, providing a high
level of design flexibility and IP security. The features of the
analog subsystem are outlined here to provide an overview of
capabilities and architecture.
„ Flexible, configurable analog routing architecture provided by
analog globals, analog mux bus, and analog local buses.
„ High resolution Delta-Sigma ADC.
9
ACK
1-7
8
DATA
9
ACK
STOP
Condition
„ Four comparators with optional connection to configurable LUT
outputs.
„ Two configurable switched capacitor/continuous time (SC/CT)
blocks for functions that include opamp, unity gain buffer,
programmable gain amplifier, transimpedance amplifier, and
mixer.
„ Two opamps for internal use and connection to GPIO that can
be used as high current output buffers.
„ CapSense subsystem to enable capacitive touch sensing.
„ Precision reference for generating an accurate analog voltage
for internal analog blocks.
„ Two 8-bit DACs that provide either voltage or current output.
Document Number: 001-53304 Rev. *K
Page 50 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 8-1. Analog Subsystem Block Diagram
R
O
U
T
I
N
G
SC/CT Block
SC/CT Block
Op
Amp
GPIO
Port
A
N
A
L
O
G
Precision
Reference
DAC
Op
Amp
A
N
A
L
O
G
DelSig
ADC
DAC
R
O
U
T
I
N
G
Com parators
CM P
CM P
CM P
G PIO
Port
CM P
CapSense Subsystem
Analog
Interface
D SI
Array
Document Number: 001-53304 Rev. *K
C lock
D istribution
C onfig &
Status
R egisters
PH UB
C PU
Decim ator
Page 51 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The PSoC Creator software program provides a user friendly
interface to configure the analog connections between the GPIO
and various analog resources and connections from one analog
resource to another. PSoC Creator also provides component
libraries that allow you to configure the various analog blocks to
perform application specific functions (PGA, transimpedance
amplifier, voltage DAC, current DAC, and so on). The tool also
generates API interface libraries that allow you to write firmware
that allows the communication between the analog peripheral
and CPU/Memory.
8.1 Analog Routing
The CY8C34 family of devices has a flexible analog routing
architecture that provides the capability to connect GPIOs and
different analog blocks, and also route signals between different
analog blocks. One of the strong points of this flexible routing
architecture is that it allows dynamic routing of input and output
connections to the different analog blocks.
„ Multiplexers and switches for input and output selection of the
analog blocks
8.1.2 Functional Description
Analog globals (AGs) and analog mux buses (AMUXBUS)
provide analog connectivity between GPIOs and the various
analog blocks. There are 16 AGs in the CY8C34 family. The
analog routing architecture is divided into four quadrants as
shown in Figure 8-2. Each quadrant has four analog globals
(AGL[0..3], AGL[4..7], AGR[0..3], AGR[4..7]). Each GPIO is
connected to the corresponding AG through an analog switch.
The analog mux bus is a shared routing resource that connects
to every GPIO through an analog switch. There are two
AMUXBUS routes in CY8C34, one in the left half (AMUXBUSL)
and one in the right half (AMUXBUSR), as shown in Figure 8-2.
For information on how to make pin selections for optimal analog
routing, refer to the application note, AN58304 - PSoC® 3 and
PSoC® 5 - Pin Selection for Analog Designs.
8.1.1 Features
„ Flexible, configurable analog routing architecture
„ 16 Analog globals (AG) and two analog mux buses
(AMUXBUS) to connect GPIOs and the analog blocks
„ Each GPIO is connected to one analog global and one analog
mux bus
„ 8 Analog local buses (abus) to route signals between the
different analog blocks
Document Number: 001-53304 Rev. *K
Page 52 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 8-2. CY8C34 Analog Interconnect
*
*
swinn
*
in0
swout
abuf_vref_int
(1.024V)
cmp0_vref
(1.024V)
COMPARATOR
sc0
Vin
Vref
out
vssa
sc0_bgref
(1.024V)
cmp0_vref
(1.024V)
refbufr
out
ref
in
refbuf_vref1 (1.024V)
refbuf_vref2 (1.2V)
refsel[1:0]
sc1
Vin
Vref
out
SC/CT
ABUSL0
ABUSL1
ABUSL2
ABUSL3
Vssa
sc1_bgref
(1.024V)
* P15[7]
VIDAC
v2
DAC2
i2
USB IO
* P15[6]
36
GPIO
P5[7]
GPIO
P5[6]
GPIO
P5[5]
GPIO
P5[4]
SIO
P12[7]
SIO
P12[6]
GPIO
* P1[7]
GPIO
* P1[6]
dac_vref (0.256V)
+
DSM0
-
ExVrefL
refmux[2:0]
ExVrefR
01 23456 7 0123
3210 76543210
13
*
GPIO
P5[0]
GPIO
P5[1]
GPIO
P5[2]
GPIO
P5[3]
GPIO
P1[0]
GPIO
P1[1]
GPIO
P1[2]
GPIO
P1[3]
GPIO
P1[4]
GPIO
P1[5]
XRES
Vbat
Vssd
Ind
Vssb
Vboost
*
Document Number: 001-53304 Rev. *K
*
Large ( ~200 Ohms)
*
Switch Resistance
Small ( ~870 Ohms )
Notes:
* Denotes pins on all packages
LCD signals are not shown.
Vddio1
*
GPIO
P2[5]
GPIO
P2[6]
GPIO
P2[7]
SIO
P12[4]
SIO
P12[5]
GPIO
P6[4]
GPIO
P6[5]
GPIO
P6[6]
GPIO
P6[7]
*
AGR[0]
AGR[3]
AGR[2]
AGR[1]
AGR[0]
AMUXBUSR
AGL[3]
AGL[2]
AGL[1]
AGL[0]
AMUXBUSL
AMUXBUSR
LPF
*
*
Connection
VBE
Vss ref
*
*
Mux Group
Switch Group
TS
ADC
AGR[3]
AGR[2]
AGR[1]
AGL[1]
AGL[2]
AGL[3]
:
AMUXBUSR
ANALOG ANALOG
BUS
GLOBALS
*
AMUXBUSL
AGL[0]
ANALOG ANALOG
GLOBALS
BUS
*
AMUXBUSL
28
*
en_resvda
DSM
vcm
refs
qtz_ref
vref_vss_ext
*
dsm0_qtz_vref2 (1.2V)
dsm0_qtz_vref1 (1.024V)
Vdda
Vdda/4
vssa
*
vpwra
vpwra/2
dsm0_vcm_vref1
(0.8V)
dsm0_vcm_vref2 (0.7V)
Vssd
Vddd
USB IO
v0
DAC0
i0
vcmsel[1:0]
en_resvpwra
Vccd
ABUSR0
ABUSR1
ABUSR2
ABUSR3
*
*
Vddio2
+
-
*
*
Vddd
comp3
CAPSENSE
out
ref
in refbufl
refsel[1:0]
GPIO
P6[0]
GPIO
P6[1]
GPIO
P6[2]
GPIO
P6[3]
GPIO
P15[4]
GPIO
P15[5]
GPIO
P2[0]
GPIO
P2[1]
GPIO
P2[2]
GPIO
P2[3] *
GPIO
P2[4] *
90
AGR[4]
AMUXBUSR
bg_vda_swabusl0
refbuf_vref1 (1.024V)
refbuf_vref2 (1.2V)
Vssd
ExVrefR
cmp1_vref
Vdda
Vdda/2
Vccd
swout
swin
comp1 +
-
+
- comp2
cmp_muxvn[1:0]
vref_cmp1
(0.256V)
bg_vda_res_en
out1
AGR[7]
AGR[6]
AGR[5]
GPIO
P4[2]
GPIO
P4[3]
GPIO
P4[4]
GPIO
P4[5]
GPIO
P4[6]
GPIO
P4[7]
in1
5
comp0
+
-
cmp1_vref
refbufl_
cmp
i2
*
LPF
out0
swin
refbufr_
cmp
i0
cmp1_vref
*
*
*
*
GPIO
P3[5]
GPIO
P3[4]
GPIO
P3[3]
GPIO
P3[2]
GPIO
P3[1]
GPIO
P3[0]
GPXT
* P15[1]
GPXT
* P15[0]
3210 76543210
swfol
swfol
*
*
AGL[6]
AGL[7]
44
01 2 3 4 56 7 0123
*
*
*
*
AGL[4]
AGL[5]
*
ExVrefL2
opamp2
*
AGR[6]
AGR[7]
AGL[7]
opamp0
*
AGR[4]
AGR[5]
AGL[4]
AGL[5]
AGL[6]
ExVrefL
ExVrefL1
*
*
*
*
AMUXBUSR
AMUXBUSL
Vddio3
GPIO
P3[6]
GPIO
P3[7]
SIO
P12[0]
SIO
P12[1]
GPIO
P15[2]
GPIO
P15[3]
AMUXBUSL
Vssd
swinp
swinp
GPIO
P0[4]
GPIO
P0[5]
GPIO
P0[6]
GPIO
P0[7]
Vcca
Vssa
Vdda
SIO
P12[2]
SIO
P12[3]
GPIO
P4[0]
GPIO
P4[1]
GPIO
P0[0]
GPIO
P0[1]
GPIO
P0[2]
GPIO
P0[3]
Vddio0
swinn
Rev #51
2-April-2010
Page 53 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Analog local buses (abus) are routing resources located within
the analog subsystem and are used to route signals between
different analog blocks. There are eight abus routes in CY8C34,
four in the left half (abusl [0:3]) and four in the right half (abusr
[0:3]) as shown in Figure 8-2. Using the abus saves the analog
globals and analog mux buses from being used for
interconnecting the analog blocks.
the input and generates a serial data stream output. This high
speed data stream is not useful for most applications without
some type of post processing, and so is passed to the decimator
through the Analog Interface block. The decimator converts the
high speed serial data stream into parallel ADC results. The
modulator/decimator frequency response is [(sin x)/x]4; a typical
frequency response is shown in Figure 8-5.
Multiplexers and switches exist on the various buses to direct
signals into and out of the analog blocks. A multiplexer can have
only one connection on at a time, whereas a switch can have
multiple connections on simultaneously. In Figure 8-2,
multiplexers are indicated by grayed ovals and switches are
indicated by transparent ovals.
Figure 8-4. Delta-sigma ADC Block Diagram
Positive
Input Mux
(Analog Routing)
Input
Buffer
Negative
Input Mux
8.2 Delta-sigma ADC
The CY8C34 device contains one delta-sigma ADC. This ADC
offers differential input, high resolution and excellent linearity,
making it a good ADC choice for measurement applications. The
converter can be configured to output 12-bit resolution at data
rates of up to 192 ksps. At a fixed clock rate, resolution can be
traded for faster data rates as shown in Table 8-1 and Figure 8-3.
Delta
Sigma
Modulator
Decimator
12 to 20 Bit
Result
EOC
SOC
Figure 8-5. Delta-sigma ADC Frequency Response,
Normalized to Output, Sample Rate = 48 kHz
0
Table 8-1. Delta-sigma ADC Performance
-10
Maximum Sample Rate
(sps)
SINAD (dB)
12
192 k
66
8
384 k
43
-20
Figure 8-3. Delta-sigma ADC Sample Rates, Range = ±1.024 V
1,000,000
frequency Response. dB
Bits
-30
-40
-50
-60
-70
-80
-90
-100
100
Sample rates, sps
100,000
1,000
10,000
100,000
1,000,000
Input Frequency, Hz
Resolution and sample rate are controlled by the Decimator.
Data is pipelined in the decimator; the output is a function of the
last four samples. When the input multiplexer is switched, the
output data is not valid until after the fourth sample after the
switch.
10,000
8.2.2 Operational Modes
1,000
Continuous
Multi-Sample
100
7
8
9
10
11
12
13
Resolution, bits
8.2.1 Functional Description
The ADC connects and configures three basic components,
input buffer, delta-sigma modulator, and decimator. The basic
block diagram is shown in Figure 8-4. The signal from the input
muxes is delivered to the delta-sigma modulator either directly or
through the input buffer. The delta-sigma modulator performs the
actual analog to digital conversion. The modulator over-samples
Document Number: 001-53304 Rev. *K
The ADC can be configured by the user to operate in one of four
modes: Single Sample, Multi Sample, Continuous, or Multi
Sample (Turbo). All four modes are started by either a write to
the start bit in a control register or an assertion of the Start of
Conversion (SoC) signal. When the conversion is complete, a
status bit is set and the output signal End of Conversion (EoC)
asserts high and remains high until the value is read by either the
DMA controller or the CPU.
8.2.2.1 Single Sample
In Single Sample mode, the ADC performs one sample
conversion on a trigger. In this mode, the ADC stays in standby
state waiting for the SoC signal to be asserted. When SoC is
signaled the ADC performs four successive conversions. The
first three conversions prime the decimator. The ADC result is
Page 54 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
hardware. This signal is optional and does not need to be
connected if ADC is running in a continuous mode.
valid and available after the fourth conversion, at which time the
EoC signal is generated. To detect the end of conversion, the
system may poll a control register for status or configure the
external EoC signal to generate an interrupt or invoke a DMA
request. When the transfer is done the ADC reenters the standby
state where it stays until another SoC event.
8.2.4 End of Conversion Output
The EoC signal goes high at the end of each ADC conversion.
This signal may be used to trigger either an interrupt or DMA
request.
8.2.2.2 Continuous
Continuous sample mode is used to take multiple successive
samples of a single input signal. Multiplexing multiple inputs
should not be done with this mode. There is a latency of three
conversion times before the first conversion result is available.
This is the time required to prime the decimator. After the first
result, successive conversions are available at the selected
sample rate.
8.3 Comparators
8.2.2.3 Multi Sample
„ Speed and power can be traded off by using one of three
The CY8C34 family of devices contains four comparators in a
device. Comparators have these features:
„ Input offset factory trimmed to less than 5 mV
„ Rail-to-rail common mode input range (VSSA to VDDA)
modes: fast, slow, or ultra low-power
Multi sample mode is similar to continuous mode except that the
ADC is reset between samples. This mode is useful when the
input is switched between multiple signals. The decimator is
re-primed between each sample so that previous samples do not
affect the current conversion. Upon completion of a sample, the
next sample is automatically initiated. The results can be
transferred using either firmware polling, interrupt, or DMA.
„ Comparator outputs can be routed to lookup tables to perform
simple logic functions and then can also be routed to digital
blocks
„ The positive input of the comparators may be optionally passed
through a low pass filter. Two filters are provided
More information on output formats is provided in the Technical
Reference Manual.
„ Comparator inputs can be connections to GPIO, DAC outputs
8.2.3 Start of Conversion Input
8.3.1 Input and Output Interface
The SoC signal is used to start an ADC conversion. A digital
clock or UDB output can be used to drive this input. It can be
used when the sampling period must be longer than the ADC
conversion time or when the ADC must be synchronized to other
The positive and negative inputs to the comparators come from
the analog global buses, the analog mux line, the analog local
bus and precision reference through multiplexers. The output
from each comparator could be routed to any of the two input
LUTs. The output of that LUT is routed to the UDB Digital System
Interface.
and SC block outputs
Figure 8-6. Analog Comparator
From
Analog
Routing
From
Analog
Routing
ANAIF
+
comp0
_
+
comp1
_
+
_
comp3
+
_
From
Analog
Routing
From
Analog
Routing
comp2
4
4
LUT0
4
4
4
LUT1
4
LUT2
4
4
LUT3
UDBs
Document Number: 001-53304 Rev. *K
Page 55 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
8.3.2 LUT
The CY8C34 family of devices contains four LUTs. The LUT is a
two input, one output lookup table that is driven by any one or
two of the comparators in the chip. The output of any LUT is
routed to the digital system interface of the UDB array. From the
digital system interface of the UDB array, these signals can be
connected to UDBs, DMA controller, I/O, or the interrupt
controller.
The LUT control word written to a register sets the logic function
on the output. The available LUT functions and the associated
control word is shown in Table 8-2.
The opamp is uncommitted and can be configured as a gain
stage or voltage follower, or output buffer on external or internal
signals.
See Figure 8-8. In any configuration, the input and output signals
can all be connected to the internal global signals and monitored
with an ADC, or comparator. The configurations are
implemented with switches between the signals and GPIO pins.
Figure 8-8. Opamp Configurations
a) Voltage Follower
Table 8-2. LUT Function vs. Program Word and Inputs
Control Word
0000b
Output (A and B are LUT inputs)
FALSE (‘0’)
0001b
0010b
0011b
0100b
0101b
0110b
0111b
1000b
1001b
1010b
1011b
1100b
1101b
1110b
1111b
A AND B
A AND (NOT B)
A
(NOT A) AND B
B
A XOR B
A OR B
A NOR B
A XNOR B
NOT B
A OR (NOT B)
NOT A
(NOT A) OR B
A NAND B
TRUE (‘1’)
8.4 Opamps
Opamp
Vin
b) External Uncommitted
Opamp
Opamp
c) Internal Uncommitted
Opamp
Vn
To Internal Signals
Opamp
Vout to Pin
Vp
Figure 8-7. Opamp
GPIO
Analog
Global Bus
GPIO
Vout to GPIO
Vp to GPIO
Vn to GPIO
GPIO Pin
The CY8C34 family of devices contains two general purpose
opamps in a device.
Analog
Global Bus
VREF
Analog
Internal Bus
Vout to Pin
Opamp
GPIO
The opamp has three speed modes, slow, medium, and fast. The
slow mode consumes the least amount of quiescent power and
the fast mode consumes the most power. The inputs are able to
swing rail-to-rail. The output swing is capable of rail-to-rail
operation at low current output, within 50 mV of the rails. When
driving high current loads (about 25 mA) the output voltage may
only get within 500 mV of the rails.
8.5 Programmable SC/CT Blocks
=
Analog Switch
The CY8C34 family of devices contains two switched
capacitor/continuous time (SC/CT) blocks in a device. Each
switched capacitor/continuous time block is built around a single
rail-to-rail high bandwidth opamp.
Switched capacitor is a circuit design technique that uses
capacitors plus switches instead of resistors to create analog
functions. These circuits work by moving charge between
Document Number: 001-53304 Rev. *K
Page 56 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The PSoC Creator tool offers a user friendly interface, which
allows you to easily program the SC/CT blocks. Switch control
and clock phase control configuration is done by PSoC Creator
so users only need to determine the application use parameters
such as gain, amplifier polarity, VREF connection, and so on.
The same opamps and block interfaces are also connectable to
an array of resistors which allows the construction of a variety of
continuous time functions.
The opamp and resistor array is programmable to perform
various analog functions including
Figure 8-9. PGA Resistor Settings
Vin
0
Vref
1
R1
R2
20 k or 40 k
20 k to 980 k
S
Vref
0
Vin
1
„ Naked operational amplifier – Continuous mode
„ Unity-gain buffer – Continuous mode
„ Programmable gain amplifier (PGA) – Continuous mode
„ Transimpedance amplifier (TIA) – Continuous mode
„ Up/down mixer – Continuous mode
„ Sample and hold mixer (NRZ S/H) – Switched cap mode
The PGA is used in applications where the input signal may not
be large enough to achieve the desired resolution in the ADC, or
dynamic range of another SC/CT block such as a mixer. The gain
is adjustable at runtime, including changing the gain of the PGA
prior to each ADC sample.
8.5.4 TIA
The Naked Opamp presents both inputs and the output for
connection to internal or external signals. The opamp has a unity
gain bandwidth greater than 6.0 MHz and output drive current up
to 650 µA. This is sufficient for buffering internal signals (such as
DAC outputs) and driving external loads greater than 7.5 kohms.
The Transimpedance Amplifier (TIA) converts an internal or
external current to an output voltage. The TIA uses an internal
feedback resistor in a continuous time configuration to convert
input current to output voltage. For an input current Iin, the output
voltage is Iin x Rfb +VREF, where VREF is the value placed on the
non inverting input. The feedback resistor Rfb is programmable
between 20 KΩ and 1 MΩ through a configuration register.
Table 8-4 shows the possible values of Rfb and associated
configuration settings.
8.5.2 Unity Gain
Table 8-4. Feedback Resistor Settings
„ First order analog to digital modulator – Switched cap mode
8.5.1 Naked Opamp
The Unity Gain buffer is a Naked Opamp with the output directly
connected to the inverting input for a gain of 1.00. It has a –3 dB
bandwidth greater than 6.0 MHz.
Configuration Word
Nominal Rfb (KΩ)
000b
20
001b
30
8.5.3 PGA
The PGA amplifies an external or internal signal. The PGA can
be configured to operate in inverting mode or noninverting mode.
The PGA function may be configured for both positive and
negative gains as high as 50 and 49 respectively. The gain is
adjusted by changing the values of R1 and R2 as illustrated in
Figure 8-9. The schematic in Figure 8-9 shows the configuration
and possible resistor settings for the PGA. The gain is switched
from inverting and non inverting by changing the shared select
value of the both the input muxes. The bandwidth for each gain
case is listed in Table 8-3.
010b
40
011b
60
100b
120
101b
250
110b
500
111b
1000
Figure 8-10. Continuous Time TIA Schematic
Table 8-3. Bandwidth
R fb
Gain
Bandwidth
1
6.0 MHz
24
340 kHz
48
220 kHz
50
215 kHz
Document Number: 001-53304 Rev. *K
I in
V ref
V out
Page 57 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
The TIA configuration is used for applications where an external
sensor's output is current as a function of some type of stimulus
such as temperature, light, magnetic flux etc. In a common
application, the voltage DAC output can be connected to the
VREF TIA input to allow calibration of the external sensor bias
current by adjusting the voltage DAC output voltage.
8.6 LCD Direct Drive
The PSoC Liquid Crystal Display (LCD) driver system is a highly
configurable peripheral designed to allow PSoC to directly drive
a broad range of LCD glass. All voltages are generated on chip,
eliminating the need for external components. With a high
multiplex ratio of up to 1/16, the CY8C34 family LCD driver
system can drive a maximum of 736 segments. The PSoC LCD
driver module was also designed with the conservative power
budget of portable devices in mind, enabling different LCD drive
modes and power down modes to conserve power.
PSoC Creator provides an LCD segment drive component. The
component wizard provides easy and flexible configuration of
LCD resources. You can specify pins for segments and
commons along with other options. The software configures the
device to meet the required specifications. This is possible
because of the programmability inherent to PSoC devices.
Key features of the PSoC LCD segment system are:
„ LCD panel direct driving
„ Type A (standard) and Type B (low-power) waveform support
Figure 8-11. LCD System
LCD
DAC
Global
Clock
UDB
LCD Driver
Block
DMA
PIN
Display
RAM
PHUB
8.6.1 LCD Segment Pin Driver
Each GPIO pin contains an LCD driver circuit. The LCD driver
buffers the appropriate output of the LCD DAC to directly drive
the glass of the LCD. A register setting determines whether the
pin is a common or segment. The pin’s LCD driver then selects
one of the six bias voltages to drive the I/O pin, as appropriate
for the display data.
8.6.2 Display Data Flow
„ Up to 62 total common and segment outputs
The LCD segment driver system reads display data and
generates the proper output voltages to the LCD glass to
produce the desired image. Display data resides in a memory
buffer in the system SRAM. Each time you need to change the
common and segment driver voltages, the next set of pixel data
moves from the memory buffer into the Port Data Registers via
DMA.
„ Up to 1/16 multiplex for a maximum of 16 backplane/common
8.6.3 UDB and LCD Segment Control
„ Wide operating voltage range support (2 V to 5 V) for LCD
panels
„ Static, 1/2, 1/3, 1/4, 1/5 bias voltage levels
„ Internal bias voltage generation through internal resistor ladder
outputs
„ Up to 62 front plane/segment outputs for direct drive
„ Drives up to 736 total segments (16 backplane × 46 front plane)
„ Up to 64 levels of software controlled contrast
„ Ability to move display data from memory buffer to LCD driver
through DMA (without CPU intervention)
„ Adjustable LCD refresh rate from 10 Hz to 150 Hz
„ Ability to invert LCD display for negative image
„ Three LCD driver drive modes, allowing power optimization
Document Number: 001-53304 Rev. *K
A UDB is configured to generate the global LCD control signals
and clocking. This set of signals is routed to each LCD pin driver
through a set of dedicated LCD global routing channels. In
addition to generating the global LCD control signals, the UDB
also produces a DMA request to initiate the transfer of the next
frame of LCD data.
8.6.4 LCD DAC
The LCD DAC generates the contrast control and bias voltage
for the LCD system. The LCD DAC produces up to five LCD drive
voltages plus ground, based on the selected bias ratio. The bias
voltages are driven out to GPIO pins on a dedicated LCD bias
bus, as required.
Page 58 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
8.7 CapSense
8.9 DAC
The CapSense system provides a versatile and efficient means
for measuring capacitance in applications such as touch sense
buttons, sliders, proximity detection, etc. The CapSense system
uses a configuration of system resources, including a few
hardware functions primarily targeted for CapSense. Specific
resource usage is detailed in the CapSense component in PSoC
Creator.
The CY8C34 parts contain two Digital to Analog Convertors
(DACs). Each DAC is 8-bit and can be configured for either
voltage or current output. The DACs support CapSense, power
supply regulation, and waveform generation. Each DAC has the
following features:
A capacitive sensing method using a delta-sigma modulator
(CSD) is used. It provides capacitance sensing using a switched
capacitor technique with a delta-sigma modulator to convert the
sensing current to a digital code.
8.8 Temp Sensor
„ Adjustable voltage or current output in 255 steps
„ Programmable step size (range selection)
„ Eight bits of calibration to correct ± 25 percent of gain error
„ Source and sink option for current output
„ 8 Msps conversion rate for current output
„ 1 Msps conversion rate for voltage output
„ Monotonic in nature
Die temperature is used to establish programming parameters
for writing flash. Die temperature is measured using a dedicated
sensor based on a forward biased transistor. The temperature
sensor has its own auxiliary ADC.
„ Data and strobe inputs can be provided by the CPU or DMA,
or routed directly from the DSI
„ Dedicated low-resistance output pin for high-current mode
Figure 8-12. DAC Block Diagram
I
Reference
Source
Scaler
Range
1x , 8x , 64x
source
Vout
R
Iout
3R
I sink Range
1x , 8x , 64x
8.9.1 Current DAC
8.10 Up/Down Mixer
The current DAC (IDAC) can be configured for the ranges 0 to
32 µA, 0 to 256 µA, and 0 to 2.048 mA. The IDAC can be
configured to source or sink current.
In continuous time mode, the SC/CT block components are used
to build an up or down mixer. Any mixing application contains an
input signal frequency and a local oscillator frequency. The
polarity of the clock, Fclk, switches the amplifier between
inverting or noninverting gain. The output is the product of the
input and the switching function from the local oscillator, with
frequency components at the local oscillator plus and minus the
signal frequency (Fclk + Fin and Fclk – Fin) and reduced-level
frequency components at odd integer multiples of the local
oscillator frequency. The local oscillator frequency is provided by
the selected clock source for the mixer.
8.9.2 Voltage DAC
For the voltage DAC (VDAC), the current DAC output is routed
through resistors. The two ranges available for the VDAC are 0
to 1.024 V and 0 to 4.096 V. In voltage mode any load connected
to the output of a DAC should be purely capacitive (the output of
the VDAC is not buffered).
Continuous time up and down mixing works for applications with
input signals and local oscillator frequencies up to 1 MHz.
Document Number: 001-53304 Rev. *K
Page 59 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
processed by a decimator to make a delta-sigma converter or a
counter to make an incremental converter. The accuracy of the
sampled data from the first-order modulator is determined from
several factors.
Figure 8-13. Mixer Configuration
C2 = 1.7 pF
C1 = 850 fF
mix
R
The main application for this modulator is for a low-frequency
ADC with high accuracy. Applications include strain gauges,
thermocouples, precision voltage, and current measurement.
0 20 k or 40 k
sc_clk
Rmix 0 20 k or 40 k
Vin
Vout
0
Vref
1
sc_clk
8.11 Sample and Hold
The main application for a sample and hold, is to hold a value
stable while an ADC is performing a conversion. Some
applications require multiple signals to be sampled
simultaneously, such as for power calculations (V and I).
Figure 8-14. Sample and Hold Topology
(Φ1 and Φ2 are opposite phases of a clock)
Φ1
Vi
C1
C2
Φ1
n
Φ1
Φ2
V ref
V out
Φ2
Φ2
Φ1
Φ2
Φ1
Φ1
V ref
Φ2
C3
C4
Φ2
Vref
8.11.1 Down Mixer
The SC/CT block can be used as a mixer to down convert an
input signal. This circuit is a high bandwidth passive sample
network that can sample input signals up to 14 MHz. This
sampled value is then held using the opamp with a maximum
clock rate of 4 MHz. The output frequency is at the difference
between the input frequency and the highest integer multiple of
the Local Oscillator that is less than the input.
9. Programming, Debug Interfaces,
Resources
PSoC devices include extensive support for programming,
testing, debugging, and tracing both hardware and firmware.
Three interfaces are available: JTAG, SWD, and SWV. JTAG and
SWD support all programming and debug features of the device.
JTAG also supports standard JTAG scan chains for board level
test and chaining multiple JTAG devices to a single JTAG
connection.
Complete Debug on Chip (DoC) functionality enables full device
debugging in the final system using the standard production
device. It does not require special interfaces, debugging pods,
simulators, or emulators. Only the standard programming
connections are required to fully support debug.
The PSoC Creator IDE software provides fully integrated
programming and debug support for PSoC devices. The low cost
MiniProg3 programmer and debugger is designed to provide full
programming and debug support of PSoC devices in conjunction
with the PSoC Creator IDE. PSoC JTAG, SWD, and SWV
interfaces are fully compatible with industry standard third party
tools.
All DOC circuits are disabled by default and can only be enabled
in firmware. If not enabled, the only way to reenable them is to
erase the entire device, clear flash protection, and reprogram the
device with new firmware that enables DOC. Disabling DOC
features, robust flash protection, and hiding custom analog and
digital functionality inside the PSoC device provide a level of
security not possible with multichip application solutions.
Additionally, all device interfaces can be permanently disabled
(Device Security) for applications concerned about phishing
attacks due to a maliciously reprogrammed device. Permanently
disabling interfaces is not recommended in most applications
because you cannot access the device later. Because all
programming, debug, and test interfaces are disabled when
Device Security is enabled, PSoCs with Device Security enabled
may not be returned for failure analysis.
Table 9-1. Debug Configurations
Debug and Trace Configuration
GPIO Pins Used
8.11.2 First Order Modulator – SC Mode
All debug and trace disabled
A first order modulator is constructed by placing the SC/CT block
in an integrator mode and using a comparator to provide a 1-bit
feedback to the input. Depending on this bit, a reference voltage
is either subtracted or added to the input signal. The block output
is the output of the comparator and not the integrator in the
modulator case. The signal is downshifted and buffered and then
JTAG
4 or 5
SWD
2
SWV
1
SWD + SWV
3
Document Number: 001-53304 Rev. *K
0
Page 60 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
9.1 JTAG Interface
9.4 Trace Features
The IEEE 1149.1 compliant JTAG interface exists on four or five
pins (the nTRST pin is optional). The JTAG clock frequency can
be up to 8 MHz, or 1/3 of the CPU clock frequency for 8 and 16-bit
transfers, or 1/5 of the CPU clock frequency for 32-bit transfers,
whichever is least. By default, the JTAG pins are enabled on new
devices but the JTAG interface can be disabled, allowing these
pins to be used as General Purpose I/O (GPIO) instead. The
JTAG interface is used for programming the flash memory,
debugging, I/O scan chains, and JTAG device chaining.
The CY8C34 supports the following trace features when using
JTAG or SWD:
9.2 Serial Wire Debug Interface
The SWD interface is the preferred alternative to the JTAG
interface. It requires only two pins instead of the four or five
needed by JTAG. SWD provides all of the programming and
debugging features of JTAG at the same speed. SWD does not
provide access to scan chains or device chaining. The SWD
clock frequency can be up to 1/3 of the CPU clock frequency.
SWD uses two pins, either two of the JTAG pins (TMS and TCK)
or the USBIO D+ and D– pins. The USBIO pins are useful for in
system programming of USB solutions that would otherwise
require a separate programming connector. One pin is used for
the data clock and the other is used for data input and output.
SWD can be enabled on only one of the pin pairs at a time. This
only happens if, within 8 µs (key window) after reset, that pin pair
(JTAG or USB) receives a predetermined sequence of 1s and 0s.
SWD is used for debugging or for programming the flash
memory.
The SWD interface can be enabled from the JTAG interface or
disabled, allowing its pins to be used as GPIO. Unlike JTAG, the
SWD interface can always be reacquired on any device during
the key window. It can then be used to reenable the JTAG
interface, if desired. When using SWD or JTAG pins as standard
GPIO, make sure that the GPIO functionality and PCB circuits do
not interfere with SWD or JTAG use.
„ Trace the 8051 program counter (PC), accumulator register
(ACC), and one SFR / 8051 core RAM register
„ Trace depth up to 1000 instructions if all registers are traced,
or 2000 instructions if only the PC is traced (on devices that
include trace memory)
„ Program address trigger to start tracing
„ Trace windowing, that is, only trace when the PC is within a
given range
„ Two modes for handling trace buffer full: continuous (overwriting
the oldest trace data) or break when trace buffer is full
9.5 Single Wire Viewer Interface
The SWV interface is closely associated with SWD but can also
be used independently. SWV data is output on the JTAG
interface’s TDO pin. If using SWV, you must configure the device
for SWD, not JTAG. SWV is not supported with the JTAG
interface.
SWV is ideal for application debug where it is helpful for the
firmware to output data similar to 'printf' debugging on PCs. The
SWV is ideal for data monitoring, because it requires only a
single pin and can output data in standard UART format or
Manchester encoded format. For example, it can be used to tune
a PID control loop in which the output and graphing of the three
error terms greatly simplifies coefficient tuning.
The following features are supported in SWV:
„ 32 virtual channels, each 32 bits long
„ Simple, efficient packing and serializing protocol
„ Supports standard UART format (N81)
9.3 Debug Features
9.6 Programming Features
Using the JTAG or SWD interface, the CY8C34 supports the
following debug features:
The JTAG and SWD interfaces provide full programming
support. The entire device can be erased, programmed, and
verified. You can increase flash protection levels to protect
firmware IP. Flash protection can only be reset after a full device
erase. Individual flash blocks can be erased, programmed, and
verified, if block security settings permit.
„ Halt and single-step the CPU
„ View and change CPU and peripheral registers, and RAM
addresses
„ Eight program address breakpoints
„ One memory access breakpoint—break on reading or writing
any memory address and data value
„ Break on a sequence of breakpoints (non recursive)
„ Debugging at the full speed of the CPU
„ Debug operations are possible while the device is reset, or in
low-power modes
„ Compatible with PSoC Creator and MiniProg3 programmer and
debugger
„ Standard JTAG programming and debugging interfaces make
CY8C34 compatible with other popular third-party tools (for
example, ARM / Keil)
Document Number: 001-53304 Rev. *K
9.7 Device Security
PSoC 3 offers an advanced security feature called device
security, which permanently disables all test, programming, and
debug ports, protecting your application from external access.
The device security is activated by programming a 32-bit key
(0x50536F43) to a Write Once Latch (WOL).
The Write Once Latch is a type of nonvolatile latch (NVL). The
cell itself is an NVL with additional logic wrapped around it. Each
WOL device contains four bytes (32 bits) of data. The wrapper
outputs a ‘1’ if a super-majority (28 of 32) of its bits match a
pre-determined pattern (0×50536F43); it outputs a ‘0’ if this
majority is not reached. When the output is 1, the Write Once NV
latch locks the part out of Debug and Test modes; it also
permanently gates off the ability to erase or alter the contents of
the latch. Matching all bits is intentionally not required, so that
single (or few) bit failures do not deassert the WOL output. The
Page 61 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
state of the NVL bits after wafer processing is truly random with
no tendency toward 1 or 0.
10. Development Support
The WOL only locks the part after the correct 32-bit key
(0×50536F43) is loaded into the NVL's volatile memory,
programmed into the NVL's nonvolatile cells, and the part is
reset. The output of the WOL is only sampled on reset and used
to disable the access. This precaution prevents anyone from
reading, erasing, or altering the contents of the internal memory.
The CY8C34 family has a rich set of documentation,
development tools, and online resources to assist you during
your development process. Visit
psoc.cypress.com/getting-started to find out more.
The user can write the key into the WOL to lock out external
access only if no flash protection is set (see “Flash Security” on
page 21). However, after setting the values in the WOL, a user
still has access to the part until it is reset. Therefore, a user can
write the key into the WOL, program the flash protection data,
and then reset the part to lock it.
If the device is protected with a WOL setting, Cypress cannot
perform failure analysis and, therefore, cannot accept RMAs
from customers. The WOL can be read out via Serial Wire Debug
(SWD) port to electrically identify protected parts. The user can
write the key in WOL to lock out external access only if no flash
protection is set. For more information on how to take full
advantage of the security features in PSoC see the PSoC 3
TRM.
Disclaimer
Note the following details of the flash code protection features on
Cypress devices.
Cypress products meet the specifications contained in their
particular Cypress data sheets. Cypress believes that its family
of products is one of the most secure families of its kind on the
market today, regardless of how they are used. There may be
methods, unknown to Cypress, that can breach the code
protection features. Any of these methods, to our knowledge,
would be dishonest and possibly illegal. Neither Cypress nor any
other semiconductor manufacturer can guarantee the security of
their code. Code protection does not mean that we are
guaranteeing the product as “unbreakable.”
Cypress is willing to work with the customer who is concerned
about the integrity of their code. Code protection is constantly
evolving. We at Cypress are committed to continuously
improving the code protection features of our products.
Document Number: 001-53304 Rev. *K
10.1 Documentation
A suite of documentation, supports the CY8C34 family to ensure
that you can find answers to your questions quickly. This section
contains a list of some of the key documents.
Software User Guide: A step-by-step guide for using PSoC
Creator. The software user guide shows you how the PSoC
Creator build process works in detail, how to use source control
with PSoC Creator, and much more.
Component data sheets: The flexibility of PSoC allows the
creation of new peripherals (components) long after the device
has gone into production. Component data sheets provide all of
the information needed to select and use a particular component,
including a functional description, API documentation, example
code, and AC/DC specifications.
Application Notes: PSoC application notes discuss a particular
application of PSoC in depth; examples include brushless DC
motor control and on-chip filtering. Application notes often
include example projects in addition to the application note
document.
Technical Reference Manual: The Technical Reference Manual
(TRM) contains all the technical detail you need to use a PSoC
device, including a complete description of all PSoC registers.
10.2 Online
In addition to print documentation, the Cypress PSoC forums
connect you with fellow PSoC users and experts in PSoC from
around the world, 24 hours a day, 7 days a week.
10.3 Tools
With industry standard cores, programming, and debugging
interfaces, the CY8C34 family is part of a development tool
ecosystem. Visit us at www.cypress.com/go/psoccreator for the
latest information on the revolutionary, easy to use PSoC Creator
IDE, supported third party compilers, programmers, debuggers,
and development kits.
Page 62 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11. Electrical Specifications
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted. The unique flexibility of the PSoC UDBs and analog blocks enable many functions to be implemented in PSoC
Creator components, see the component data sheets for full AC/DC specifications of individual functions. See the “Example
Peripherals” section on page 39 for further explanation of PSoC Creator components.
11.1 Absolute Maximum Ratings
Table 11-1. Absolute Maximum Ratings DC Specifications
Parameter
Description
Min
Typ
Max
Units
–55
25
100
°C
Analog supply voltage relative to
VSSA
–0.5
–
6
V
VDDD
Digital supply voltage relative to
VSSD
–0.5
–
6
V
VDDIO
I/O supply voltage relative to VSSD
–0.5
–
6
V
VCCA
Direct analog core voltage input
–0.5
–
1.95
V
VCCD
Direct digital core voltage input
–0.5
–
1.95
V
VSSA
Analog ground voltage
VSSD –0.5
–
VSSD +
0.5
V
VGPIO[17]
DC input voltage on GPIO
Includes signals sourced by VDDA
and routed internal to the pin
VSSD –0.5
–
VDDIO +
0.5
V
VSIO
DC input voltage on SIO
Output disabled
VSSD –0.5
–
7
V
Output enabled
VSSD –0.5
–
6
V
TSTG
Storage temperature
VDDA
VIND
Voltage at boost converter input
VBAT
Boost converter supply
Ivddio
Current per VDDIO supply pin
Vextref
ADC external reference inputs
Conditions
Higher storage temperatures
reduce NVL data retention time.
Recommended storage temperature is +25 °C ±25 °C. Extended
duration storage temperatures
above 85 °C degrade reliability.
Pins P0[3], P3[2]
current[18]
0.5
–
5.5
V
VSSD –0.5
–
5.5
V
–
–
100
mA
–
–
2
V
LU
Latch up
–140
–
140
mA
ESDHBM
Electrostatic discharge voltage
Human body model
750
–
–
V
ESDCDM
Electrostatic discharge voltage
Charge device model
500
–
–
V
Note Usage above the absolute maximum conditions listed in Table 11-1 may cause permanent damage to the device. Exposure to
maximum conditions for extended periods of time may affect device reliability. When used below maximum conditions but above
normal operating conditions the device may not operate to specification.
Notes
17. The VDDIO supply voltage must be greater than the maximum analog voltage on the associated GPIO pins. Maximum analog voltage on GPIO pin ≤ VDDIO ≤ VDDA.
18. Meets or exceeds JEDEC Spec EIA/JESD78 IC Latch-up Test.
Document Number: 001-53304 Rev. *K
Page 63 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2 Device Level Specifications
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.2.1 Device Level Specifications
Table 11-2. DC Specifications
Min
Typ
Max
Units
VDDA
Parameter
Analog supply voltage and input to
analog core regulator
Description
Analog core regulator enabled
1.8
–
5.5
V
VDDA
Analog supply voltage, analog
regulator bypassed
Analog core regulator disabled
1.71
1.8
1.89
V
VDDD
Digital supply voltage relative to VSSD Digital core regulator enabled
1.8
–
VDDA[19]
V
VDDD
Digital supply voltage, digital
regulator bypassed
1.71
1.8
1.89
V
VDDIO[20]
I/O supply voltage relative to VSSIO
1.71
–
VDDA[19]
V
VCCA
Direct analog core voltage input
(Analog regulator bypass)
Analog core regulator disabled
1.71
1.8
1.89
V
VCCD
Direct digital core voltage input
(Digital regulator bypass)
Digital core regulator disabled
1.71
1.8
1.89
V
IDD[21]
Active Mode, VDD = 1.71 V – 5.5 V
Bus clock off. Execute from CPU
instruction buffer. See “Flash
Program Memory” on page 21.
Conditions
Digital core regulator disabled
CPU at 3 MHz
CPU at 6 MHz
CPU at 12 MHz
CPU at 24 MHz
CPU at 48 MHz
VDD = 3.3 V, T = 25 °C, IMO and bus
clock enabled, ILO = 1 kHz, CPU
executing from flash and accessing
SRAM, all other blocks off, all I/Os
tied low.
T = –40 °C
–
–
–
mA
T = 25 °C
–
0.8
–
mA
T = 85 °C
–
–
–
mA
T = –40 °C
–
–
–
mA
T = 25 °C
–
1.2
–
mA
T = 85 °C
–
–
–
mA
T = –40 °C
–
–
–
mA
T = 25 °C
–
2.0
–
mA
T = 85 °C
–
–
–
mA
T = –40 °C
–
–
–
mA
T = 25 °C
–
3.5
–
mA
T = 85 °C
–
–
–
mA
T = –40 °C
–
–
–
mA
T = 25 °C
–
6.6
–
mA
T = 85 °C
–
–
–
mA
CPU at 3 MHz
–
1.4
–
mA
CPU at 6 MHz
–
2.2
–
mA
CPU at 12 MHz
–
3.6
–
mA
CPU at 24 MHz
–
6.4
–
mA
CPU at 48 MHz
–
11.8
–
mA
Notes
19. The power supplies can be brought up in any sequence however once stable VDDA must be greater than or equal to all other supplies.
20. The VDDIO supply voltage must be greater than the maximum analog voltage on the associated GPIO pins. Maximum analog voltage on GPIO pin ≤ VDDIO ≤ VDDA.
21. The current consumption of additional peripherals that are implemented only in programmed logic blocks can be found in their respective data sheets, available in
PSoC Creator, the integrated design environment. To estimate total current, find CPU current at frequency of interest and add peripheral currents for your particular
system from the device data sheet and component data sheets.
Document Number: 001-53304 Rev. *K
Page 64 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-2. DC Specifications (continued)
Parameter
Description
Conditions
Min
Typ
Max
Units
T = –40 °C
–
–
–
µA
T = 25 °C
–
–
–
µA
T = 85 °C
–
–
–
µA
[22]
Sleep Mode
CPU = OFF
RTC = ON (= ECO32K ON, in
low-power mode)
Sleep timer = ON (= ILO ON at
1 kHz)[23]
WDT = OFF
I2C Wake = OFF
Comparator = OFF
POR = ON
Boost = OFF
SIO pins in single ended input,
unregulated output mode
VDD = VDDIO = 4.5 – 5.5 V
VDD = VDDIO = 2.7 – 3.6 V
T = –40 °C
–
–
–
µA
T = 25 °C
–
1
–
µA
T = 85 °C
–
–
–
µA
–
–
–
µA
T = 25 °C
–
–
–
µA
T = 85 °C
–
–
–
µA
VDD = VDDIO = 1.71 – 1.95 V T = –40 °C
Comparator = ON
CPU = OFF
RTC = OFF
Sleep timer = OFF
WDT = OFF
I2C Wake = OFF
POR = ON
Boost = OFF
SIO pins in single ended input,
unregulated output mode
VDD = VDDIO = 2.7 – 3.6V
T = 25 °C
–
–
–
µA
I2C Wake = ON
CPU = OFF
RTC = OFF
Sleep timer = OFF
WDT = OFF
Comparator = OFF
POR = ON
Boost = OFF
SIO pins in single ended input,
unregulated output mode
VDD = VDDIO = 2.7 – 3.6V
T = 25 °C
–
–
–
µA
VDD = VDDIO = 4.5 – 5.5 V
T = –40 °C
–
–
–
nA
T = 25 °C
–
–
–
nA
T = 85 °C
–
–
–
nA
Hibernate Mode[22]
Hibernate mode current
All regulators and oscillators off.
SRAM retention
GPIO interrupts are active
Boost = OFF
SIO pins in single ended input,
unregulated output mode
VDD = VDDIO = 2.7 – 3.6 V
T = –40 °C
–
–
–
nA
T = 25 °C
–
200
–
nA
T = 85 °C
–
–
–
nA
–
–
–
nA
T = 25 °C
–
–
–
nA
T = 85 °C
–
–
–
nA
VDD = VDDIO = 1.71 – 1.95 V T = –40 °C
Notes
22. If VCCD and VCCA are externally regulated, the voltage difference between VCCD and VCCA must be less than 50 mV.
23. Sleep timer generates periodic interrupts to wake up the CPU. This specification applies only to those times that the CPU is off.
Document Number: 001-53304 Rev. *K
Page 65 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-1. Active Mode Current vs FCPU, VDD = 3.3 V,
Temperature = 25 °C
Figure 11-2. Active Mode Current vs Temperature and FCPU,
VDD = 3.3 V
Figure 11-3. Active Mode Current vs VDD and Temperature,
FCPU = 24 MHz
Document Number: 001-53304 Rev. *K
Page 66 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-3. AC Specifications[24]
Parameter
Description
Conditions
Min
Typ
Max
Units
FCPU
CPU frequency
1.71 V ≤ VDDD ≤ 5.5 V
DC
–
50.01
MHz
FBUSCLK
Bus frequency
1.71 V ≤ VDDD ≤ 5.5 V
DC
–
50.01
MHz
Svdd
VDD ramp rate
–
–
–
1
V/ns
TIO_INIT
Time from VDDD/VDDA/VCCD/VCCA ≥ –
IPOR to I/O ports set to their reset
states
–
–
10
µs
TSTARTUP
Time from VDDD/VDDA/VCCD/VCCA ≥ VCCA/VCCD = regulated from
PRES to CPU executing code at
VDDA/VDDD, no PLL used, IMO boot
reset vector
mode (12 MHz typ.)
–
–
66
µs
TSLEEP
Wakeup from sleep mode –
Application of non-LVD interrupt to
beginning of execution of next CPU
instruction
–
–
15
µs
THIBERNATE
Wakeup from hibernate mode –
Application of external interrupt to
beginning of execution of next CPU
instruction
–
–
100
µs
Figure 11-4. FCPU vs. VDD
Vdd Voltage
5.5 V
Valid Operating Region
3.3 V
1.71 V
Valid Operating Region with SMP
0.5 V
0V
DC
1 MHz
10 MHz
50 MHz
CPU Frequency
Note
24. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 67 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.3 Power Regulators
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.3.1 Digital Core Regulator
Table 11-4. Digital Core Regulator DC Specifications
Parameter
Description
VDDD
Input voltage
VCCD
Output voltage
Regulator output capacitor
Conditions
±10%, X5R ceramic or better. The two
VCCD pins must be shorted together, with
as short a trace as possible, see Power
System on page 28
Figure 11-5. Regulators VCC vs VDD
Min
1.8
–
–
Typ
–
1.80
1
Max
5.5
–
–
Units
V
V
µF
Figure 11-6. Digital Regulator PSRR vs Frequency and VDD
11.3.2 Analog Core Regulator
Table 11-5. Analog Core Regulator DC Specifications
Parameter
Description
VDDA
Input voltage
VCCA
Output voltage
Regulator output capacitor
Conditions
±10%, X5R ceramic or better
Min
1.8
–
–
Typ
–
1.80
1
Max
5.5
–
–
Units
V
V
µF
Figure 11-7. Analog Regulator PSRR vs Frequency and VDD
Document Number: 001-53304 Rev. *K
Page 68 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.3.3 Inductive Boost Regulator.
Table 11-6. Inductive Boost Regulator DC Specifications
Unless otherwise specified, operating conditions are: VBAT = 2.4 V, VOUT = 2.7 V, IOUT = 40 mA, FSW = 400 kHz, LBOOST = 10 µH,
CBOOST = 22 µF || 0.1 µF
Parameter
VBAT
IOUT
Description
Min
Typ
Max
Units
T=-35 °C to +65 °C
0.5
–
3.6
V
Over entire temperature range
0.68
–
3.6
V
VBAT = 1.6 – 3.6 V, VOUT = 3.6 – 5.0 V,
external diode
–
–
50
mA
VBAT = 1.6 – 3.6 V, VOUT = 1.6 – 3.6 V,
internal diode
–
–
75
mA
VBAT = 0.8 – 1.6 V, VOUT = 1.6 – 3.6 V,
internal diode
–
–
30
mA
VBAT = 0.8 – 1.6 V, VOUT = 3.6 – 5.0 V,
external diode
–
–
20
mA
VBAT = 0.5 – 0.8 V, VOUT = 1.6 – 3.6 V,
internal diode
–
–
15
mA
–
–
700
mA
Boost active mode
–
200
–
µA
Boost standby mode, 32 khz external crystal
oscillator, IOUT < 1 µA
–
12
–
µA
1.8 V
1.71
1.80
1.89
V
1.9 V
1.81
1.90
2.00
V
2.0 V
1.90
2.00
2.10
V
2.4 V
2.28
2.40
2.52
V
2.7 V
2.57
2.70
2.84
V
3.0 V
2.85
3.00
3.15
V
3.3 V
3.14
3.30
3.47
V
3.6 V
3.42
3.60
3.78
V
4.75
5.00
5.25
V
–
–
3.8
%
Input voltage
Includes startup
Load current
[25, 26]
ILPK
Inductor peak current
IQ
Quiescent current
VOUT
Conditions
Boost voltage range[27, 28]
5.0 V
RegLOAD
Load regulation
RegLINE
Line regulation
η
Efficiency
External diode required
–
–
4.1
%
LBOOST = 10 µH
70
85
–
%
LBOOST = 22 µH
82
90
–
%
Notes
25. For output voltages above 3.6 V, an external diode is required.
26. Maximum output current applies for output voltages ≤ 4x input voltage.
27. Based on device characterization (Not production tested).
28. At boost frequency of 2 MHz,VOUT is limited to 2 x VBAT. At 400 kHz, VOUT is limited to 4 x VBAT.
Document Number: 001-53304 Rev. *K
Page 69 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-7. Inductive Boost Regulator AC Specifications
Unless otherwise specified, operating conditions are: VBAT = 2.4 V, VOUT = 2.7 V, IOUT = 40 mA, FSW = 400 kHz, LBOOST = 10 µH,
CBOOST = 22 µF || 0.1 µF.
Parameter
Description
VRIPPLE
Ripple voltage (peak-to-peak)
FSW
Switching frequency
Conditions
Min
Typ
Max
VOUT = 1.8 V, FSW = 400 kHz, IOUT = 10 mA
Units
–
–
100
mV
–
0.1, 0.4,
or 2
–
MHz
Table 11-8. Recommended External Components for Boost Circuit
Parameter
LBOOST
Description
Conditions
Boost inductor
capacitor[29]
CBOOST
Filter
IF
External Schottky diode
average forward current
External Schottky diode is required for
VOUT > 3.6 V
VR
Figure 11-8. Efficiency vs VOUT
IOUT = 30 mA, VBAT ranges from 0.7 V to VOUT, LBOOST = 22 µH
Min
Typ
Max
Units
4.7
10
47
µH
10
22
47
µF
1
–
–
A
20
–
–
V
Figure 11-9. Efficiency vs VBAT
IOUT = 30 mA, VOUT = 3.3 V, LBOOST = 22 µH
Note
29. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 70 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-10. Efficiency vs IOUT
VBAT = 2.4 V, VOUT = 3.3 V
Figure 11-11. Efficiency vs IOUT
VBAT ranges from 0.7 V to 3.3 V, LBOOST = 22 µH
Figure 11-12. Efficiency vs Switching Frequency
VOUT = 3.3 V, VBAT = 2.4 V, IOUT = 40 mA
Document Number: 001-53304 Rev. *K
Page 71 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.1 Inputs and Outputs
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted. Unless otherwise specified, all charts and graphs show typical values.
11.1.1 GPIO
Table 11-9. GPIO DC Specifications
Parameter
VIH
VIL
VIH
VIH
VIL
VIL
VOH
Description
Input voltage high threshold
Input voltage low threshold
Input voltage high threshold
Input voltage high threshold
Input voltage low threshold
Input voltage low threshold
Output voltage high
VOL
Output voltage low
Rpullup
Pull-up resistor
Rpulldown Pull-down resistor
IIL
Input leakage current (absolute
value)[30]
CIN
Input capacitance[30]
VH
Idiode
Rglobal
Rmux
Conditions
CMOS Input, PRT[×]CTL = 0
CMOS Input, PRT[×]CTL = 0
LVTTL Input, PRT[×]CTL = 1,VDDIO < 2.7 V
LVTTL Input, PRT[×]CTL = 1, VDDIO ≥ 2.7V
LVTTL Input, PRT[×]CTL = 1,VDDIO < 2.7 V
LVTTL Input, PRT[×]CTL = 1, VDDIO ≥ 2.7V
IOH = 4 mA at 3.3 VDDIO
IOH = 1 mA at 1.8 VDDIO
IOL = 8 mA at 3.3 VDDIO
IOL = 4 mA at 1.8 VDDIO
25 °C, VDDIO = 3.0 V
GPIOs without opamp outputs
GPIOs with opamp outputs
Input voltage hysteresis
(Schmitt-Trigger)[30]
Current through protection diode to
VDDIO and VSSIO
Resistance pin to analog global bus 25 °C, VDDIO = 3.0 V
Resistance pin to analog mux bus 25 °C, VDDIO = 3.0 V
Figure 11-13. GPIO Output High Voltage and Current
Min
0.7 × VDDIO
–
0.7 × VDDIO
2.0
–
–
VDDIO – 0.6
VDDIO – 0.5
–
–
3.5
3.5
–
Typ
–
–
–
–
–
–
–
–
–
–
5.6
5.6
–
Max
Units
–
V
0.3 × VDDIO
V
–
V
–
V
0.3 × VDDIO
V
0.8
V
–
V
–
V
0.6
V
0.6
V
8.5
kΩ
8.5
kΩ
2
nA
–
–
–
–
–
40
7
18
–
pF
pF
mV
–
–
100
µA
–
–
320
220
–
–
Ω
Ω
Figure 11-14. GPIO Output Low Voltage and Current
Note
30. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 72 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-10. GPIO AC Specifications
Parameter
Description
TriseF
Rise time in Fast Strong Mode[31]
TfallF
TriseS
TfallS
Fgpioout
Fgpioin
Conditions
3.3 V VDDIO Cload = 25 pF
Min
–
Typ
–
Max
12
Units
ns
3.3 V VDDIO Cload = 25 pF
3.3 V VDDIO Cload = 25 pF
3.3 V VDDIO Cload = 25 pF
–
–
–
–
–
–
12
60
60
ns
ns
ns
90/10% VDDIO into 25 pF
–
–
33
MHz
90/10% VDDIO into 25 pF
–
–
20
MHz
3.3 V < VDDIO < 5.5 V, slow strong 90/10% VDDIO into 25 pF
drive mode
–
–
7
MHz
1.71 V < VDDIO < 3.3 V, slow strong 90/10% VDDIO into 25 pF
drive mode
GPIO input operating frequency
90/10% VDDIO
1.71 V < VDDIO < 5.5 V
–
–
3.5
MHz
–
–
50
MHz
Fall time in Fast Strong Mode[31]
Rise time in Slow Strong Mode[31]
Fall time in Slow Strong Mode[31]
GPIO output operating frequency
2.7 V < VDDIO < 5.5 V, fast strong
drive mode
1.71 V < VDDIO < 2.7 V, fast strong
drive mode
Figure 11-15. GPIO Output Rise and Fall Times, Fast Strong
Mode, VDDIO = 3.3 V, 25 pF Load
Figure 11-16. GPIO Output Rise and Fall Times, Slow Strong
Mode, VDDIO = 3.3 V, 25 pF Load
Note
31. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 73 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.1.2 SIO
Table 11-11. SIO DC Specifications
Parameter
Vinmax
Description
Maximum input voltage
Vinref
Input voltage reference (Differential
0.5
input mode)
Output voltage reference (Regulated output mode)
VDDIO > 3.7
1
VDDIO < 3.7
1
Input voltage high threshold
0.7 × VDDIO
GPIO mode
CMOS input
Differential input mode[32]
Hysteresis disabled
SIO_ref + 0.2
Input voltage low threshold
–
GPIO mode
CMOS input
Differential input mode[32]
Hysteresis disabled
–
Output voltage high
VDDIO – 0.4
Unregulated mode
IOH = 4 mA, VDDIO = 3.3 V
Regulated mode[32]
IOH = 1 mA
SIO_ref – 0.65
Regulated mode[32]
IOH = 0.1 mA
SIO_ref – 0.3
Output voltage low
–
VDDIO = 3.30 V, IOL = 25 mA
VDDIO = 1.80 V, IOL = 4 mA
–
Pull-up resistor
3.5
Pull-down resistor
3.5
Input leakage current (absolute
value)[33]
VIH < Vddsio
25 °C, Vddsio = 3.0 V, VIH = 3.0 V
–
VIH > Vddsio
25 °C, Vddsio = 0 V, VIH = 3.0 V
–
Input Capacitance[33]
–
Input voltage hysteresis
Single ended mode (GPIO mode)
–
(Schmitt-Trigger)[33]
Differential mode
–
–
Current through protection diode to
VSSIO
Voutref
VIH
VIL
VOH
VOL
Rpullup
Rpulldown
IIL
CIN
VH
Idiode
Conditions
All allowed values of Vddio and
Vddd, see Section 11.2.1
Min
–
Typ
–
Max
5.5
Units
V
–
0.52 × VDDIO
V
–
–
VDDIO – 1
VDDIO – 0.5
V
V
–
–
–
–
V
V
–
–
0.3 × VDDIO
SIO_ref – 0.2
V
V
–
–
–
–
SIO_ref + 0.2
SIO_ref + 0.2
V
V
V
–
–
5.6
5.6
0.8
0.4
8.5
8.5
V
V
kΩ
kΩ
–
–
–
40
35
–
14
10
7
–
–
100
nA
µA
pF
mV
mV
µA
Notes
32. See Figure 6-9 on page 34 and Figure 6-12 on page 37 for more information on SIO reference.
33. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 74 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-17. SIO Output High Voltage and Current,
Unregulated Mode
Figure 11-18. SIO Output Low Voltage and Current,
Unregulated Mode
Figure 11-19. SIO Output High Voltage and Current,
Regulated Mode
Table 11-12. SIO AC Specifications
Parameter
TriseF
TfallF
TriseS
TfallS
Description
Rise time in Fast Strong Mode
(90/10%)[34]
Fall time in Fast Strong Mode
(90/10%)[34]
Rise time in Slow Strong Mode
(90/10%)[34]
Fall time in Slow Strong Mode
(90/10%)[34]
Conditions
Cload = 25 pF, VDDIO = 3.3 V
Min
–
Typ
–
Max
12
Units
ns
Cload = 25 pF, VDDIO = 3.3 V
–
–
12
ns
Cload = 25 pF, VDDIO = 3.0 V
–
–
75
ns
Cload = 25 pF, VDDIO = 3.0 V
–
–
60
ns
Note
34. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 75 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-12. SIO AC Specifications (continued)
Parameter
Fsioout
Fsioin
Description
SIO output operating frequency
2.7 V < VDDIO < 5.5 V, Unregulated
output (GPIO) mode, fast strong
drive mode
1.71 V < VDDIO < 2.7 V, Unregulated output (GPIO) mode, fast
strong drive mode
3.3 V < VDDIO < 5.5 V, Unregulated
output (GPIO) mode, slow strong
drive mode
1.71 V < VDDIO < 3.3 V, Unregulated output (GPIO) mode, slow
strong drive mode
2.7 V < VDDIO < 5.5 V, Regulated
output mode, fast strong drive mode
1.71 V < VDDIO < 2.7 V, Regulated
output mode, fast strong drive mode
1.71 V < VDDIO < 5.5 V, Regulated
output mode, slow strong drive
mode
SIO input operating frequency
1.71 V < VDDIO < 5.5 V
Conditions
Min
Typ
Max
Units
90/10% VDDIO into 25 pF
–
–
33
MHz
90/10% VDDIO into 25 pF
–
–
16
MHz
90/10% VDDIO into 25 pF
–
–
5
MHz
90/10% VDDIO into 25 pF
–
–
4
MHz
Output continuously switching
into 25 pF
Output continuously switching
into 25 pF
Output continuously switching
into 25 pF
–
–
20
MHz
–
–
10
MHz
–
–
2.5
MHz
90/10% VDDIO
–
–
50
MHz
Figure 11-20. SIO Output Rise and Fall Times, Fast Strong
Mode, VDDIO = 3.3 V, 25 pF Load
Figure 11-21. SIO Output Rise and Fall Times, Slow Strong
Mode, VDDIO = 3.3 V, 25 pF Load
11.1.3 USBIO
For operation in GPIO mode, the standard range for VDDD applies, see Device Level Specifications on page 64.
Table 11-13. USBIO DC Specifications
Parameter
Rusbi
Rusba
Vohusb
Description
USB D+ pull-up resistance
USB D+ pull-up resistance
Static output high
Volusb
Static output low
Document Number: 001-53304 Rev. *K
Conditions
With idle bus
While receiving traffic
15 kΩ ±5% to Vss, internal pull-up
enabled
15 kΩ ±5% to Vss, internal pull-up
enabled
Min
0.900
1.425
2.8
Typ
–
–
–
Max
1.575
3.090
3.6
Units
kΩ
kΩ
V
–
–
0.3
V
Page 76 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-13. USBIO DC Specifications (continued)
Parameter
Vihgpio
Vilgpio
Vohgpio
Volgpio
Vdi
Vcm
Vse
Rps2
Rext
Zo
CIN
IIL
Description
Input voltage high, GPIO mode
Input voltage low, GPIO mode
Output voltage high, GPIO mode
Output voltage low, GPIO mode
Differential input sensitivity
Differential input common mode
range
Single ended receiver threshold
PS/2 pull-up resistance
External USB series resistor
USB driver output impedance
USB transceiver input capacitance
Input leakage current (absolute
value)
Conditions
VDDD ≥ 3 V
VDDD ≥ 3 V
IOH = 4 mA, VDDD ≥ 3 V
IOL = 4 mA, VDDD ≥ 3 V
|(D+) – (D–)|
In PS/2 mode, with PS/2 pull-up
enabled
In series with each USB pin
Including Rext
25 °C, VDDD = 3.0 V
Figure 11-22. USBIO Output High Voltage and Current, GPIO
Mode
Document Number: 001-53304 Rev. *K
Min
2
–
2.4
–
–
0.8
Typ
–
–
–
–
–
–
Max
–
0.8
–
0.3
0.2
2.5
Units
V
V
V
V
V
V
0.8
3
–
–
2
7
V
kΩ
21.78
(–1%)
28
–
–
22
22.22
(+1%)
44
20
2
Ω
–
–
–
Ω
pF
nA
Figure 11-23. USBIO Output Low Voltage and Current, GPIO
Mode
Page 77 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-14. USBIO AC Specifications
Parameter
Description
Tdrate
Full-speed data rate average bit rate
Tjr1
Tjr2
Tdj1
Tdj2
Tfdeop
Tfeopt
Tfeopr
Tfst
Fgpio_out
Tr_gpio
Tf_gpio
Conditions
Receiver data jitter tolerance to next
transition
Receiver data jitter tolerance to pair
transition
Driver differential jitter to next transition
Driver differential jitter to pair transition
Source jitter for differential transition to
SE0 transition
Source SE0 interval of EOP
Receiver SE0 interval of EOP
Width of SE0 interval during differential
transition
GPIO mode output operating
3 V ≤ VDDD ≤ 5.5 V
frequency
VDDD = 1.71 V
Rise time, GPIO mode, 10%/90% VDDD VDDD > 3 V, 25 pF load
VDDD = 1.71 V, 25 pF load
Fall time, GPIO mode, 90%/10% VDDD VDDD > 3 V, 25 pF load
VDDD = 1.71 V, 25 pF load
Min
12 – 0.25%
Typ
12
Units
MHz
–
Max
12 +
0.25%
8
–8
–5
–
5
ns
–3.5
–4
–2
–
–
–
3.5
4
5
ns
ns
ns
160
82
–
–
–
–
175
–
14
ns
ns
ns
–
–
–
–
–
–
–
–
–
–
–
–
20
6
12
40
12
40
MHz
MHz
ns
ns
ns
ns
Min
–
–
90%
Typ
–
–
–
Max
20
20
111%
Units
ns
ns
1.3
–
2
V
ns
Figure 11-24. USBIO Output Rise and Fall Times, GPIO Mode,
VDDD = 3.3 V, 25 pF Load
Table 11-15. USB Driver AC Specifications
Parameter
Description
Tr
Transition rise time
Tf
Transition fall time
TR
Rise/fall time matching
Vcrs
Output signal crossover voltage
Document Number: 001-53304 Rev. *K
Conditions
VUSB_5, VUSB_3.3, see USB DC
Specifications on page 99
Page 78 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.1.4 XRES
Table 11-16. XRES DC Specifications
Parameter
VIH
VIL
Rpullup
CIN
VH
Idiode
Description
Input voltage high threshold
Input voltage low threshold
Pull-up resistor
Input capacitance[35]
Input voltage hysteresis
(Schmitt-Trigger)[35]
Current through protection diode to
VDDIO and VSSIO
Conditions
Min
0.7 × VDDIO
–
3.5
–
–
Typ
–
–
5.6
3
100
Max
–
0.3 × VDDIO
8.5
–
–
Units
V
V
kΩ
pF
mV
–
–
100
µA
Table 11-17. XRES AC Specifications
Parameter
TRESET
Description
Reset pulse width
Conditions
Min
Typ
Max
Units
1
–
–
µs
Note
35. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 79 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2 Analog Peripherals
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.2.1 Opamp
Table 11-18. Opamp DC Specifications
Parameter
Description
VIOFF
Input offset voltage
Vos
Conditions
Input offset voltage
Operating temperature –40 °C to
70 °C
Min
–
Typ
–
Max
2
Units
mV
–
–
2.5
mV
–
–
2
mV
µV / °C
TCVos
Input offset voltage drift with temperature
Power mode = high
–
±12
–
Ge1
Gain error, unity gain buffer mode
Rload = 1 kΩ
–
–
±0.1
%
Cin
Input capacitance
Routing from pin
–
–
18
pF
Vo
Output voltage range
1 mA, source or sink, power mode = VSSA + 0.05
high
–
VDDA –
0.05
V
Iout
Output current, source or sink
VSSA + 500 mV ≤ Vout ≤ VDDA
–500 mV, VDDA > 2.7 V
25
–
–
mA
VSSA + 500 mV ≤ Vout ≤ VDDA
–500 mV, 1.7 V = VDDA ≤ 2.7 V
16
–
–
mA
Power mode = min
–
200
270
uA
Idd
Quiescent current
Power mode = low
–
250
400
uA
Power mode = med
–
330
950
uA
Power mode = high
CMRR
Common mode rejection ratio
PSRR
Power supply rejection ratio
–
1000
2500
uA
80
–
–
dB
Vdda ≥ 2.7 V
85
–
–
dB
Vdda < 2.7 V
70
–
–
dB
Figure 11-25. Opamp Voffset Histogram, 3388 samples/847
parts, 25 °C, Vdda = 5 V
Document Number: 001-53304 Rev. *K
Figure 11-26. Opamp Voffset vs Temperature, Vdda = 5V
Page 80 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-27. Opamp Voffset vs Vcommon and
Vdda, 25 °C
Figure 11-28. Opamp Output Voltage vs Load Current and
Temperature, High Power Mode, 25 °C, Vdda = 2.7 V
Figure 11-29. Opamp Operating Current vs Vdda and Power
Mode
Table 11-19. Opamp AC Specifications
Parameter
Description
GBW
Gain-bandwidth product
SR
Slew rate, 20% - 80%
en
Input noise density
Document Number: 001-53304 Rev. *K
Conditions
Power mode = minimum, 200 pF load
Power mode = low, 200 pF load
Power mode = medium, 200 pF load
Power mode = high, 200 pF load
Power mode = low, 200 pF load
Power mode = medium, 200 pF load
Power mode = high, 200 pF load
Power mode = high, Vdda = 5 V,
at 100 kHz
Min
1
2
1
3
1.1
0.9
3
–
Typ
–
–
–
–
–
–
–
45
Max
–
–
–
–
–
–
–
–
Units
MHz
MHz
MHz
MHz
V/µs
V/µs
V/µs
nV/sqrtHz
Page 81 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-30. Opamp Noise vs Frequency, Power Mode =
High, Vdda = 5V
Figure 11-31. Opamp Step Response, Rising
Figure 11-32. Opamp Step Response, Falling
Document Number: 001-53304 Rev. *K
Page 82 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.2 Delta-sigma ADC
Unless otherwise specified, operating conditions are:
„ Operation in continuous sample mode
„ fclk = 6.144 MHz
„ Reference = 1.024 V internal reference bypassed on P3.2 or P0.3
„ Unless otherwise specified, all charts and graphs show typical values
Table 11-20. 12-bit Delta-sigma ADC DC Specifications
Parameter
Description
Conditions
Resolution
Number of channels, single ended
Number of channels, differential
Monotonic
Ge
Gain error
Gd
Gain drift
Vos
Input offset voltage
TCVos
Temperature coefficient, input offset voltage
Differential pair is formed using a pair
of GPIOs.
Yes
Buffered, buffer gain = 1,
Range = ±1.024 V, 25 °C
Buffered, buffer gain = 1,
Range = ±1.024 V
Buffered, 16-bit mode, VDDA = 2.7 V,
25 °C
Buffer gain = 1, 16-bit,
Range = ±1.024 V
ended[36]
INL12
DNL12
INL8
DNL8
Rin_Buff
Input voltage range, single
Input voltage range, differential unbuffered[36]
Input voltage range, differential, buffered[36]
Integral non linearity[36]
Differential non linearity[36]
Integral non linearity[36]
Differential non linearity[36]
ADC input resistance
Rin_ADC12 ADC input resistance
Range = ±1.024 V, unbuffered
Range = ±1.024 V, unbuffered
Range = ±1.024 V, unbuffered
Range = ±1.024 V, unbuffered
Input buffer used
Input buffer bypassed, 12 bit, Range
= ±1.024 V
ADC external reference input voltage, see
also internal reference in Voltage Reference Pins P0[3], P3[2]
on page 85
Current Consumption
IDD_12
Current consumption, 12 bit[36]
192 ksps, unbuffered
[36]
Buffer current consumption
IBUFF
Vextref
Min
8
Typ
–
Units
bits
–
Max
12
No. of
GPIO
No. of
GPIO/2
–
–
–
–
–
–
–
–
±0.2
%
–
–
50
ppm/°
C
–
–
±0.1
mV
–
–
55
µV/°C
VSSA
VSSA
VSSA
–
–
–
–
10
–
–
–
–
–
–
–
–
VDDA
VDDA
VDDA – 1
±1
±1
±1
±1
–
V
V
V
LSB
LSB
LSB
LSB
MΩ
–
148[37]
–
kΩ
0.9
–
1.3
V
–
–
–
–
1.4
2.5
mA
mA
–
–
–
Notes
36. Based on device characterization (Not production tested).
37. By using switched capacitors at the ADC input an effective input resistance is created. Holding the gain and number of bits constant, the resistance is proportional
to the inverse of the clock frequency. This value is calculated, not measured. For more information see the Technical Reference Manual.
Document Number: 001-53304 Rev. *K
Page 83 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-21. Delta-sigma ADC AC Specifications
Parameter
Description
Conditions
Startup time
Total harmonic distortion[38]
THD
Min
Typ
Max
Units
–
–
4
Samples
Buffer gain = 1, 16 bit,
Range = ±1.024 V
–
–
0.0032
%
12-Bit Resolution Mode
SR12
Sample rate, continuous, high power[38]
Range = ±1.024 V, unbuffered
4
–
192
ksps
BW12
Input bandwidth at max sample rate[38]
Range = ±1.024 V, unbuffered
–
44
–
kHz
Range = ±1.024 V, unbuffered
66
–
–
dB
Range = ±1.024 V, unbuffered
8
–
384
ksps
SINAD12int Signal to noise ratio, 12-bit, internal
reference[38]
8-Bit Resolution Mode
Sample rate, continuous, high power[38]
SR8
rate[38]
BW8
Input bandwidth at max sample
Range = ±1.024 V, unbuffered
–
88
–
kHz
SINAD8int
Signal to noise ratio, 8-bit, internal reference[38] Range = ±1.024 V, unbuffered
43
–
–
dB
Table 11-22. Delta-sigma ADC Sample Rates, Range = ±1.024 V
Continuous
Resolution,
Bits
Min
Max
8
8000
9
6400
10
11
12
Multi-Sample
Min
Max
384000
1911
91701
307200
1543
74024
5566
267130
1348
64673
4741
227555
1154
55351
4000
192000
978
46900
Figure 11-33. Delta-sigma ADC IDD vs sps, Range = ±1.024 V,
Continuous Sample Mode, Input Buffer Bypassed
Note
38. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 84 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.3 Voltage Reference
Table 11-23. Voltage Reference Specifications
See also ADC external reference specifications in Section 11.2.2.
Parameter
VREF
Description
Conditions
Precision reference voltage
Initial trim
Min
Typ
Max
Units
1.014
(–1%)
1.024
1.034
(+1%)
V
Min
Typ
Max
Units
11.2.4 Analog Globals
Table 11-24. Analog Globals Specifications
Parameter
Description
Conditions
Rppag
Resistance pin-to-pin through
analog global[39]
VDDA = 3.0 V
–
939
1461
Ω
Rppmuxbus
Resistance pin-to-pin through
analog mux bus[39]
VDDA = 3.0 V
–
721
1135
Ω
Min
Typ
11.2.5 Comparator
Table 11-25. Comparator DC Specifications
Parameter
Max
Units
Input offset voltage in fast mode
Description
Factory trim, Vdda > 2.7 V,
Vin ≥ 0.5 V
Conditions
–
10
mV
Input offset voltage in slow mode
Factory trim, Vin ≥ 0.5 V
–
9
mV
VOS
Custom trim
–
–
4
mV
Input offset voltage in slow mode[40] Custom trim
–
–
4
mV
VOS
Input offset voltage in ultra
low-power mode
–
±12
–
mV
VHYST
Hysteresis
Hysteresis enable mode
–
10
32
mV
VICM
Input common mode voltage
High current / fast mode
VSSA
–
VDDA – 0.1
V
Low current / slow mode
VSSA
–
VDDA
V
Ultra low power mode
VSSA
–
VDDA – 0.9
VOS
Input offset voltage in fast
mode[40]
CMRR
Common mode rejection ratio
–
50
–
dB
ICMP
High current mode/fast mode[41]
–
–
400
µA
Low current mode/slow mode[41]
–
–
100
µA
Ultra low-power mode[41]
–
6
–
µA
Table 11-26. Comparator AC Specifications
Parameter
Description
Min
Typ
Max
Units
50 mV overdrive, measured
pin-to-pin
–
75
110
ns
Response time, low current mode[41] 50 mV overdrive, measured
pin-to-pin
–
155
200
ns
Response time, ultra low-power
mode[41]
–
55
–
µs
Response time, high current
mode[41]
TRESP
Conditions
50 mV overdrive, measured
pin-to-pin
Notes
39. The resistance of the analog global and analog mux bus is high if VDDA ≤ 2.7 V, and the chip is in either sleep or hibernate mode. Use of analog global and analog
mux bus under these conditions is not recommended.
40. The recommended procedure for using a custom trim value for the on-chip comparators can be found in the TRM.
41. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 85 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.6 Current Digital-to-analog Converter (IDAC)
See the IDAC component data sheet in PSoC Creator for full electrical specifications and APIs.
Unless otherwise specified, all charts and graphs show typical values.
Table 11-27. IDAC DC Specifications
Parameter
Description
Conditions
Resolution
IOUT
Output current at code = 255
Min
Typ
Max
Units
–
–
8
bits
Range = 2.048 mA, code = 255,
VDDA ≥ 2.7 V, Rload = 600 Ω
–
2.048
–
mA
Range = 2.048 mA, High mode,
code = 255, VDDA ≤ 2.7 V, Rload =
300 Ω
–
2.048
–
mA
Range = 255 µA, code = 255, Rload
= 600 Ω
–
255
–
µA
Range = 31.875 µA, code = 255,
Rload = 600 Ω
–
31.875
–
µA
Monotonicity
–
–
Yes
Ezs
Zero scale error
–
0
±1
LSB
Eg
Gain error
Range = 2.048 mA, 25 °C
–
–
±2.5
%
Range = 255 µA, 25 ° C
–
–
±2.5
%
Range = 31.875 µA, 25 ° C
–
–
±3.5
%
Range = 2.048 mA
–
–
0.04
% / °C
Range = 255 µA
–
–
0.04
% / °C
Range = 31.875 µA
–
–
0.05
% / °C
Sink mode, range = 255 µA, Codes
8 – 255, Rload = 2.4 kΩ, Cload =
15 pF
–
±0.9
±1
LSB
Source mode, range = 255 µA,
Codes 8 – 255, Rload = 2.4 kΩ,
Cload = 15 pF
–
±1.2
±1.5
LSB
Sink mode, range = 255 µA, Rload
= 2.4 kΩ, Cload = 15 pF
–
±0.3
±1
LSB
Source mode, range = 255 µA,
Rload = 2.4 kΩ, Cload = 15 pF
–
±0.3
±1
LSB
Voltage headroom at max current,
Rload to Vdda or Rload to Vssa,
Vdiff from Vdda
1
–
–
V
TC_Eg
INL
DNL
Vcompliance
Temperature coefficient of gain
error
Integral nonlinearity
Differential nonlinearity
Dropout voltage, source or sink
mode
Document Number: 001-53304 Rev. *K
Page 86 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-27. IDAC DC Specifications (continued)
Parameter
IDD
Description
Operating current, code = 0
Conditions
Min
Typ
Max
Units
Slow mode, source mode, range =
31.875 µA
–
44
100
µA
Slow mode, source mode, range =
255 µA,
–
33
100
µA
Slow mode, source mode, range =
2.04 mA
–
33
100
µA
Slow mode, sink mode, range =
31.875 µA
–
36
100
µA
Slow mode, sink mode, range =
255 µA
–
33
100
µA
Slow mode, sink mode, range =
2.04 mA
–
33
100
µA
Fast mode, source mode, range =
31.875 µA
–
310
500
µA
Fast mode, source mode, range =
255 µA
–
305
500
µA
Fast mode, source mode, range =
2.04 mA
–
305
500
µA
Fast mode, sink mode, range =
31.875 µA
–
310
500
µA
Fast mode, sink mode, range =
255 µA
–
300
500
µA
Fast mode, sink mode, range =
2.04 mA
–
300
500
µA
Figure 11-34. IDAC INL vs Input Code, Range = 255 µA,
Source Mode
Document Number: 001-53304 Rev. *K
Figure 11-35. IDAC INL vs Input Code, Range = 255 µA, Sink
Mode
Page 87 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-36. IDAC DNL vs Input Code, Range = 255 µA,
Source Mode
Figure 11-37. IDAC DNL vs Input Code, Range = 255 µA, Sink
Mode
Figure 11-38. IDAC INL vs Temperature, Range = 255 µA, Fast
Mode
Figure 11-39. IDAC DNL vs Temperature, Range = 255 µA,
Fast Mode
Document Number: 001-53304 Rev. *K
Page 88 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-40. IDAC Full Scale Error vs Temperature, Range
= 255 µA, Source Mode
Figure 11-41. IDAC Full Scale Error vs Temperature, Range
= 255 µA, Sink Mode
Figure 11-42. IDAC Operating Current vs Temperature,
Range = 255 µA, Code = 0, Source Mode
Figure 11-43. IDAC Operating Current vs Temperature,
Range = 255 µA, Code = 0, Sink Mode
Document Number: 001-53304 Rev. *K
Page 89 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-28. IDAC AC Specifications
Parameter
Description
FDAC
Update rate
TSETTLE
Settling time to 0.5 LSB
Conditions
Min
–
Range = 31.875 µA or 255 µA, full
scale transition, fast mode, 600 Ω
15-pF load
–
Figure 11-44. IDAC Step Response, Codes 0x40 - 0xC0,
255 µA Mode, Source Mode, Fast Mode, Vdda = 5 V
Typ
Max
Units
–
8
Msps
–
125
ns
Figure 11-45. IDAC Glitch Response, Codes 0x7F - 0x80,
255 µA Mode, Source Mode, Fast Mode, Vdda = 5 V
Figure 11-46. IDAC PSRR vs Frequency
Document Number: 001-53304 Rev. *K
Page 90 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.7 Voltage Digital to Analog Converter (VDAC)
See the VDAC component data sheet in PSoC Creator for full electrical specifications and APIs.
Unless otherwise specified, all charts and graphs show typical values.
Table 11-29. VDAC DC Specifications
Parameter
Description
Conditions
Resolution
8
–
bits
±2.5
LSB
1 V scale
–
±0.3
±1
LSB
1 V scale
–
4
–
kΩ
4 V scale
–
16
–
kΩ
1 V scale
–
1
–
V
–
4
–
V
–
–
Yes
–
Differential nonlinearity
Rout
Output resistance
VOUT
Output voltage range, code = 255
1 V scale
4 V scale, Vdda = 5 V
Monotonicity
Gain error
TC_Eg
IDD
Operating current
Units
±2.1
DNL1
Zero scale error
Max
–
Integral nonlinearity
Eg
Typ
–
INL1
VOS
Min
–
0
±0.9
LSB
1 V scale
–
–
±2.5
%
4 V scale
–
–
±2.5
%
Temperature coefficient, gain error 1 V scale
–
–
0.03
%FSR / °C
Figure 11-47. VDAC INL vs Input Code, 1 V Mode
Document Number: 001-53304 Rev. *K
4 V scale
–
–
0.03
%FSR / °C
Slow mode
–
–
100
µA
Fast mode
–
–
500
µA
Figure 11-48. VDAC DNL vs Input Code, 1 V Mode
Page 91 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-49. VDAC INL vs Temperature, 1 V Mode
Figure 11-50. VDAC DNL vs Temperature, 1 V Mode
Figure 11-51. VDAC Full Scale Error vs Temperature, 1 V
Mode
Figure 11-52. VDAC Full Scale Error vs Temperature, 4 V
Mode
Figure 11-53. VDAC Operating Current vs Temperature, 1V
Mode, Slow Mode
Figure 11-54. VDAC Operating Current vs Temperature, 1 V
Mode, Fast Mode
Document Number: 001-53304 Rev. *K
Page 92 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-30. VDAC AC Specifications
Parameter
FDAC
Description
Update rate
Conditions
Min
Typ
Max
Units
1 V scale
–
–
1000
ksps
4 V scale
–
–
250
ksps
–
0.45
1
µs
TsettleP
Settling time to 0.1%, step 25% to 1 V scale, Cload = 15 pF
75%
4 V scale, Cload = 15 pF
–
0.8
3.2
µs
TsettleN
Settling time to 0.1%, step 75% to 1 V scale, Cload = 15 pF
25%
–
0.45
1
µs
4 V scale, Cload = 15 pF
–
0.7
3
µs
Figure 11-55. VDAC Step Response, Codes 0x40 - 0xC0, 1 V
Mode, Fast Mode, Vdda = 5 V
Figure 11-56. VDAC Glitch Response, Codes 0x7F - 0x80, 1 V
Mode, Fast Mode, Vdda = 5 V
Figure 11-57. VDAC PSRR vs Frequency
Document Number: 001-53304 Rev. *K
Page 93 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.8 Mixer
The mixer is created using a SC/CT analog block; see the Mixer component data sheet in PSoC Creator for full electrical specifications
and APIs.
Table 11-31. Mixer DC Specifications
Parameter
VOS
G
Description
Conditions
Min
Typ
Max
Units
–
–
10
mV
Quiescent current
–
0.9
2
mA
Gain
–
0
–
dB
Min
Typ
Max
Units
Input offset voltage
Table 11-32. Mixer AC Specifications
Parameter
Description
Conditions
fLO
Local oscillator frequency
Down mixer mode
–
–
4
MHz
fin
Input signal frequency
Down mixer mode
–
–
14
MHz
fLO
Local oscillator frequency
Up mixer mode
–
–
1
MHz
fin
Input signal frequency
Up mixer mode
–
–
1
MHz
SR
Slew rate
3
–
–
V/µs
11.2.9 Transimpedance Amplifier
The TIA is created using a SC/CT analog block; see the TIA component data sheet in PSoC Creator for full electrical specifications
and APIs.
Table 11-33. Transimpedance Amplifier (TIA) DC Specifications
Parameter
Description
VIOFF
Input offset voltage
Rconv
Conversion resistance[42]
Conditions
Min
Typ
Max
Units
–
–
10
mV
R = 20K; 40 pF load
–25
–
+35
%
R = 30K; 40 pF load
–25
–
+35
%
R = 40K; 40 pF load
–25
–
+35
%
R = 80K; 40 pF load
–25
–
+35
%
R = 120K; 40 pF load
–25
–
+35
%
R = 250K; 40 pF load
–25
–
+35
%
R= 500K; 40 pF load
–25
–
+35
%
R = 1M; 40 pF load
–25
–
+35
%
–
1.1
2
mA
Quiescent current
Table 11-34. Transimpedance Amplifier (TIA) AC Specifications
Parameter
BW
Description
Input bandwidth (–3 dB)
Min
Typ
Max
Units
R = 20K; –40 pF load
Conditions
1500
–
–
kHz
R = 120K; –40 pF load
240
–
–
kHz
R = 1M; –40 pF load
25
–
–
kHz
Note
42. Conversion resistance values are not calibrated. Calibrated values and details about calibration are provided in PSoC Creator component data sheets. External
precision resistors can also be used.
Document Number: 001-53304 Rev. *K
Page 94 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.2.10 Programmable Gain Amplifier
The PGA is created using a SC/CT analog block; see the PGA component data sheet in PSoC Creator for full electrical specifications
and APIs.
Unless otherwise specified, operating conditions are:
„ Operating temperature = 25 °C for typical values
„ Unless otherwise specified, all charts and graphs show typical values
Table 11-35. PGA DC Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
Vssa
–
Vdda
V
Vin
Input voltage range
Power mode = minimum
Vos
Input offset voltage
Power mode = high,
gain = 1
–
–
10
mV
TCVos
Input offset voltage drift
with temperature
Power mode = high,
gain = 1
–
–
±30
µV/°C
Ge1
Gain error, gain = 1
–
–
±0.15
%
Ge16
Gain error, gain = 16
–
–
±2.5
%
Ge50
Gain error, gain = 50
–
–
±5
%
Vonl
DC output nonlinearity
–
–
±0.01
% of
FSR
Cin
Input capacitance
–
–
7
pF
Voh
Output voltage swing
Power mode = high,
gain = 1, Rload = 100 kΩ
to VDDA / 2
VDDA – 0.15
–
–
V
Vol
Output voltage swing
Power mode = high,
gain = 1, Rload = 100 kΩ
to VDDA / 2
–
–
VSSA + 0.15
V
Vsrc
Output voltage under load
Iload = 250 µA, Vdda ≥
2.7V, power mode = high
–
–
300
mV
Idd
Operating current
Power mode = high
–
1.5
1.65
mA
PSRR
Power supply rejection
ratio
48
–
–
dB
Gain = 1
Figure 11-58. PGA Voffset Histogram, 4096 samples/
1024 parts
Document Number: 001-53304 Rev. *K
Page 95 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-36. PGA AC Specifications
Parameter
BW1
Description
–3 dB bandwidth
SR1
Slew rate
en
Input noise density
Conditions
Power mode = high,
gain = 1, input = 100 mV
peak-to-peak
Power mode = high,
gain = 1, 20% to 80%
Power mode = high,
Vdda = 5 V, at 100 kHz
Figure 11-59. Bandwidth vs. Temperature, at Different Gain
Settings, Power Mode = High
Min
6.7
Typ
8
Max
–
Units
MHz
3
–
–
V/µs
–
43
–
nV/sqrtHz
Figure 11-60. Noise vs. Frequency, Vdda = 5 V,
Power Mode = High
11.2.11 Temperature Sensor
Table 11-37. Temperature Sensor Specifications
Parameter
Description
Temp sensor accuracy
Conditions
Range: –40 °C to +85 °C
Min
–
Typ
±5
Max
–
Units
°C
11.2.12 LCD Direct Drive
Table 11-38. LCD Direct Drive DC Specifications
Parameter
Description
ICC
LCD system operating current
ICC_SEG
VBIAS
IOUT
Conditions
Device sleep mode with wakeup at
400-Hz rate to refresh LCDs, bus
clock = 3 Mhz, Vddio = Vdda = 3 V,
4 commons, 16 segments, 1/4 duty
cycle, 50 Hz frame rate, no glass
connected
Current per segment driver
Strong drive mode
LCD bias range (VBIAS refers to the main VDDA ≥ 3 V and VDDA ≥ VBIAS
output voltage(V0) of LCD DAC)
LCD bias step size
VDDA ≥ 3 V and VDDA ≥ VBIAS
LCD capacitance per
Drivers may be combined
segment/common driver
Long term segment offset
Output drive current per segment driver) Vddio = 5.5V, strong drive mode
Min
–
Typ
38
Max
–
Units
μA
–
2
260
–
–
5
µA
V
–
–
9.1 × VDDA
500
–
5000
mV
pF
–
355
–
–
20
710
mV
µA
Min
Typ
Max
Units
10
50
150
Hz
Table 11-39. LCD Direct Drive AC Specifications
Parameter
fLCD
Description
LCD frame rate
Document Number: 001-53304 Rev. *K
Conditions
Page 96 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.3 Digital Peripherals
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.3.1 Timer
The following specifications apply to the Timer/Counter/PWM peripheral in timer mode. Timers can also be implemented in UDBs; for
more information, see the Timer component data sheet in PSoC Creator.
Table 11-40. Timer DC Specifications
Parameter
Description
Block current consumption
Conditions
16-bit timer, at listed input clock
frequency
3 MHz
12 MHz
50 MHz
Min
–
Typ
–
Max
–
Units
µA
–
–
–
15
60
260
–
–
–
µA
µA
µA
Min
DC
21
42
21
21
42
21
42
Typ
–
–
–
–
–
–
–
–
Max
50.01
–
–
–
–
–
–
–
Units
MHz
ns
ns
ns
ns
ns
ns
ns
Table 11-41. Timer AC Specifications
Parameter
Description
Operating frequency
Capture pulse width (Internal)
Capture pulse width (external)
Timer resolution
Enable pulse width
Enable pulse width (external)
Reset pulse width
Reset pulse width (external)
Conditions
11.3.2 Counter
The following specifications apply to the Timer/Counter/PWM peripheral, in counter mode. Counters can also be implemented in
UDBs; for more information, see the Counter component data sheet in PSoC Creator.
Table 11-42. Counter DC Specifications
Parameter
Description
Block current consumption
Conditions
16–bit counter, at listed input clock
frequency
3 MHz
12 MHz
50 MHz
Min
–
Typ
–
Max
–
Units
µA
–
–
–
15
60
260
–
–
–
µA
µA
µA
Min
DC
21
21
21
42
21
42
21
42
Typ
–
–
–
–
Max
50.01
–
–
–
–
–
–
–
–
–
–
–
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
Table 11-43. Counter AC Specifications
Parameter
Description
Operating frequency
Capture pulse
Resolution
Pulse width
Pulse width (external)
Enable pulse width
Enable pulse width (external)
Reset pulse width
Reset pulse width (external)
Document Number: 001-53304 Rev. *K
Conditions
Page 97 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.3.3 Pulse Width Modulation
The following specifications apply to the Timer/Counter/PWM peripheral, in PWM mode. PWM components can also be implemented
in UDBs; for more information, see the PWM component data sheet in PSoC Creator.
Table 11-44. PWM DC Specifications
Parameter
Description
Min
Typ
Max
Units
–
–
–
µA
3 MHz
–
15
–
µA
12 MHz
–
60
–
µA
50 MHz
–
260
–
µA
Block current consumption
Conditions
16-bit PWM, at listed input clock
frequency
Table 11-45. Pulse Width Modulation (PWM) AC Specifications
Parameter
Min
Typ
Max
Units
Operating frequency
Description
Conditions
DC
–
50.01
MHz
Pulse width
21
–
–
ns
Pulse width (external)
42
–
–
ns
Kill pulse width
21
–
–
ns
Kill pulse width (external)
42
Enable pulse width
21
–
–
ns
Enable pulse width (external)
42
–
–
ns
Reset pulse width
21
–
–
ns
Reset pulse width (external)
42
–
–
ns
Min
Typ
Max
Units
ns
11.3.4 I2C
Table 11-46. Fixed I2C DC Specifications
Parameter
Description
Block current consumption
Conditions
Enabled, configured for 100 kbps
–
–
250
µA
Enabled, configured for 400 kbps
–
–
260
µA
Wake from sleep mode
–
–
30
µA
Min
Typ
Max
Units
–
–
1
Mbps
Typ
–
Max
200
Units
µA
Table 11-47. Fixed I2C AC Specifications
Parameter
Description
Conditions
Bit rate
11.3.5 Controller Area Network[43]
Table 11-48. CAN DC Specifications
Parameter
IDD
Description
Block current consumption
Conditions
Min
–
Conditions
Min
Typ
Max
Units
–
–
1
Mbit
Table 11-49. CAN AC Specifications
Parameter
Description
Bit rate
Minimum 8 MHz clock
Note
43. Refer to ISO 11898 specification for details.
Document Number: 001-53304 Rev. *K
Page 98 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.3.6 USB
Table 11-50. USB DC Specifications
Parameter
Description
Min
Typ
Max
Units
USB configured, USB regulator
enabled
4.35
–
5.25
V
VUSB_3.3
USB configured, USB regulator
bypassed
3.15
–
3.6
V
VUSB_3
USB configured, USB regulator
bypassed[44]
2.85
–
3.6
V
VUSB_5
Device supply for USB operation
IUSB_Configured
Conditions
Device supply current in device active VDDD = 5 V, FCPU = 1.5 MHz
mode, bus clock and IMO = 24 MHz V
DDD = 3.3 V, FCPU = 1.5 MHz
–
10
–
mA
–
8
–
mA
–
0.5
–
mA
VDDD = 5 V, disconnected from
USB host
–
0.3
–
mA
VDDD = 3.3 V, connected to USB
host, PICU configured to wake on
USB resume signal
–
0.5
–
mA
VDDD = 3.3 V, disconnected from
USB host
–
0.3
–
mA
IUSB_Suspended Device supply current in device sleep VDDD = 5 V, connected to USB
mode
host, PICU configured to wake on
USB resume signal
11.3.7 Universal Digital Blocks (UDBs)
PSoC Creator provides a library of pre-built and tested standard digital peripherals (UART, SPI, LIN, PRS, CRC, timer, counter, PWM,
AND, OR, and so on) that are mapped to the UDB array. See the component data sheets in PSoC Creator for full AC/DC specifications,
APIs, and example code.
Table 11-51. UDB AC Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
FMAX_TIMER Maximum frequency of 16-bit timer in a
UDB pair
–
–
50.01
MHz
FMAX_ADDER Maximum frequency of 16-bit adder in
a UDB pair
–
–
50.01
MHz
FMAX_CRC
–
–
50.01
MHz
–
–
50.01
MHz
Datapath Performance
Maximum frequency of 16-bit
CRC/PRS in a UDB pair
PLD Performance
FMAX_PLD
Maximum frequency of a two-pass PLD
function in a UDB pair
Clock to Output Performance
tCLK_OUT
Propagation delay for clock in to data
out, see Figure 11-61.
25 °C, Vddd ≥ 2.7 V
–
20
25
ns
tCLK_OUT
Propagation delay for clock in to data
out, see Figure 11-61.
Worst-case placement, routing, and
pin selection
–
–
55
ns
Note
44. Rise/fall time matching (TR) not guaranteed, see USB Driver AC Specifications on page 78.
Document Number: 001-53304 Rev. *K
Page 99 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-61. Clock to Output Performance
11.4 Memory
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.4.1 Flash
Table 11-52. Flash DC Specifications
Parameter
Description
Erase and program voltage
Conditions
VDDD pin
Min
Typ
Max
Units
1.71
–
5.5
V
Min
Typ
Max
Units
Table 11-53. Flash AC Specifications
Parameter
Description
Conditions
TWRITE
Row write time (erase + program)
–
15
20
ms
TERASE
Row erase time
–
10
13
ms
Row program time
–
5
7
ms
Bulk erase time (16 KB to 64 KB)
–
–
35
ms
Sector erase time (8 KB to 16 KB)
–
–
15
ms
Total device program time, including
JTAG or SWD, and other overhead
–
–
5
Seconds
Average ambient temp.
TA ≤ 55 °C, 100 K erase/program
cycles
20
–
–
years
Average ambient temp.
TA ≤ 85 °C, 10 K erase/program
cycles
10
–
–
years
Min
Typ
Max
Units
1.71
–
5.5
V
TBULK
Flash data retention time, retention
period measured from last erase cycle
11.4.2 EEPROM
Table 11-54. EEPROM DC Specifications
Parameter
Description
Erase and program voltage
Document Number: 001-53304 Rev. *K
Conditions
Page 100 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 11-55. EEPROM AC Specifications
Parameter
TWRITE
Description
Conditions
Min
Typ
Max
Units
Single row erase/write cycle time
–
2
20
ms
EEPROM data retention time, retention Average ambient temp, TA ≤ 25 °C,
period measured from last erase cycle 1M erase/program cycles
20
–
–
years
Average ambient temp, TA ≤ 55 °C,
100 K erase/program cycles
20
–
–
Average ambient temp.
TA ≤ 85 °C, 10 K erase/program
cycles
10
–
–
Min
Typ
Max
Units
1.71
–
5.5
V
Min
Typ
Max
Units
Programmed at 25 °C
1K
–
–
program/
erase
cycles
Programmed at 0 °C to 70 °C
100
–
–
program/
erase
cycles
Programmed at 25 °C
20
–
–
years
Programmed at 0 °C to 70 °C
20
–
–
years
Min
Typ
Max
Units
1.2
–
–
V
Min
Typ
Max
Units
DC
–
50.01
MHz
11.4.3 Nonvolatile Latches (NVL))
Table 11-56. NVL DC Specifications
Parameter
Description
Erase and program voltage
Conditions
VDDD pin
Table 11-57. NVL AC Specifications
Parameter
Description
NVL endurance
NVL data retention time
Conditions
11.4.4 SRAM
Table 11-58. SRAM DC Specifications
Parameter
VSRAM
Description
Conditions
SRAM retention voltage
Table 11-59. SRAM AC Specifications
Parameter
FSRAM
Description
SRAM operating frequency
Document Number: 001-53304 Rev. *K
Conditions
Page 101 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.4.5 External Memory Interface
Figure 11-62. Asynchronous Read Cycle Timing
Tcel
EM_ CEn
Taddrv
EM_ Addr
Taddrh
Address
Toel
EM_ OEn
EM_ WEn
Tdoesu
Tdoeh
EM_ Data
Data
Table 11-60. Asynchronous Read Cycle Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
30.3
–
–
nS
2T – 5
–
2T+ 5
nS
–
–
5
nS
T
–
–
nS
2T – 5
–
2T + 5
nS
T
EMIF clock period[45]
Tcel
EM_CEn low time
Taddrv
EM_CEn low to EM_Addr valid
Taddrh
Address hold time after EM_Wen high
Toel
EM_OEn low time
Tdoesu
Data to EM_OEn high setup time
T + 15
–
–
nS
Tdoeh
Data hold time after EM_OEn high
3
–
–
nS
Vdda ≥ 3.3 V
Note
45. Limited by GPIO output frequency, see Table 11-10 on page 73.
Document Number: 001-53304 Rev. *K
Page 102 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-63. Asynchronous Write Cycle Timing
Taddrv
Taddrh
EM_ Addr
Address
Tcel
EM_ CEn
Twel
EM_ WEn
EM_ OEn
Tdweh
Tdcev
EM_ Data
Data
Table 11-61. Asynchronous Write Cycle Specifications
Parameter
Description
period[46]
T
EMIF clock
Tcel
EM_CEn low time
Taddrv
Taddrh
Twel
EM_WEn low time
Tdcev
EM_CEn low to data valid
Tdweh
Data hold time after EM_WEn high
Conditions
Vdda ≥ 3.3 V
Min
Typ
Max
Units
30.3
–
–
nS
T–5
–
T+5
nS
EM_CEn low to EM_Addr valid
–
–
5
nS
Address hold time after EM_WEn high
T
–
–
nS
T–5
–
T+5
nS
–
–
7
nS
T
–
–
nS
Note
46. Limited by GPIO output frequency, see Table 11-10 on page 73.
Document Number: 001-53304 Rev. *K
Page 103 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-64. Synchronous Read Cycle Timing
Tcp/2
EM_ Clock
Tceld
Tcehd
EM_ CEn
Taddriv
Taddrv
EM_ Addr
Address
Toeld
Toehd
EM_ OEn
Tds
Data
EM_ Data
Tadscld
Tadschd
EM_ ADSCn
Table 11-62. Synchronous Read Cycle Specifications
Parameter
Description
Min
Typ
Max
Units
30.3
–
–
nS
T/2
–
–
nS
5
–
–
nS
EM_Clock high to EM_CEn high
T/2 – 5
–
–
nS
EM_Addr valid to EM_Clock high
5
–
–
nS
T/2 – 5
–
–
nS
5
–
–
nS
EM_Clock high to EM_OEn high
T
–
–
nS
Data valid before EM_OEn high
T + 15
–
–
nS
EM_ADSCn low to EM_Clock high
5
–
–
nS
EM_Clock high to EM_ADSCn high
T/2 – 5
–
–
nS
T
EMIF clock period[47]
Tcp/2
EM_Clock pulse high
Tceld
EM_CEn low to EM_Clock high
Tcehd
Taddrv
Taddriv
EM_Clock high to EM_Addr invalid
Toeld
EM_OEn low to EM_Clock high
Toehd
Tds
Tadscld
Tadschd
Conditions
Vdda ≥ 3.3 V
Note
47. Limited by GPIO output frequency, see Table 11-10 on page 73.
Document Number: 001-53304 Rev. *K
Page 104 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-65. Synchronous Write Cycle Timing
Tcp/2
EM_ Clock
Tceld
Tcehd
EM_ CEn
Taddriv
Taddrv
EM_ Addr
Address
Tweld
Twehd
EM_ WEn
Tdh
Tds
Data
EM_ Data
Tadschd
Tadscld
EM_ ADSCn
Table 11-63. Synchronous Write Cycle Specifications
Parameter
Description
Period[48]
Conditions
Vdda ≥ 3.3 V
Min
Typ
Max
Units
30.3
–
–
nS
T/2
–
–
nS
T
EMIF clock
Tcp/2
EM_Clock pulse high
Tceld
EM_CEn low to EM_Clock high
5
–
–
nS
Tcehd
EM_Clock high to EM_CEn high
T/2 – 5
–
–
nS
Taddrv
EM_Addr valid to EM_Clock high
Taddriv
EM_Clock high to EM_Addr invalid
Tweld
Twehd
Tds
Tdh
Tadscld
Tadschd
5
–
–
nS
T/2 – 5
–
–
nS
EM_WEn low to EM_Clock high
5
–
–
nS
EM_Clock high to EM_WEn high
T/2 – 5
–
–
nS
Data valid before EM_Clock high
5
–
–
nS
Data invalid after EM_Clock high
T
–
–
nS
EM_ADSCn low to EM_Clock high
5
–
–
nS
EM_Clock high to EM_ADSCn high
T/2 – 5
–
–
nS
Note
48. Limited by GPIO output frequency, see Table 11-10 on page 73.
Document Number: 001-53304 Rev. *K
Page 105 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.5 PSoC System Resources
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.5.1 POR with Brown Out
For brown out detect in regulated mode, VDDD and VDDA must be ≥ 2.0 V. Brown out detect is not available in externally regulated
mode.
Table 11-64. Precise power-on Reset (PRES) with Brown Out DC Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
1.64
–
1.68
V
1.62
–
1.66
V
Min
Typ
Max
Units
–
–
0.5
µs
–
5
–
V/sec
Min
Typ
Max
Units
1.68
1.89
2.14
2.38
2.62
2.87
3.11
3.35
3.59
3.84
4.08
4.32
4.56
4.83
5.05
5.30
5.57
1.73
1.95
2.20
2.45
2.71
2.95
3.21
3.46
3.70
3.95
4.20
4.45
4.70
4.98
5.21
5.47
5.75
1.77
2.01
2.27
2.53
2.79
3.04
3.31
3.56
3.81
4.07
4.33
4.59
4.84
5.13
5.37
5.63
5.92
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Min
Typ
Max
Units
–
–
1
µs
Precise POR (PPOR)
PRESR
Rising trip voltage
PRESF
Falling trip voltage
Factory trim
Table 11-65. Power-on Reset (POR) with Brown Out AC Specifications
Parameter
Description
Conditions
PRES_TR Response time
VDDD/VDDA droop rate
Sleep mode
11.5.2 Voltage Monitors
Table 11-66. Voltage Monitors DC Specifications
Parameter
Description
LVI
Trip voltage
LVI_A/D_SEL[3:0] = 0000b
LVI_A/D_SEL[3:0] = 0001b
LVI_A/D_SEL[3:0] = 0010b
LVI_A/D_SEL[3:0] = 0011b
LVI_A/D_SEL[3:0] = 0100b
LVI_A/D_SEL[3:0] = 0101b
LVI_A/D_SEL[3:0] = 0110b
LVI_A/D_SEL[3:0] = 0111b
LVI_A/D_SEL[3:0] = 1000b
LVI_A/D_SEL[3:0] = 1001b
LVI_A/D_SEL[3:0] = 1010b
LVI_A/D_SEL[3:0] = 1011b
LVI_A/D_SEL[3:0] = 1100b
LVI_A/D_SEL[3:0] = 1101b
LVI_A/D_SEL[3:0] = 1110b
LVI_A/D_SEL[3:0] = 1111b
HVI
Trip voltage
Conditions
Table 11-67. Voltage Monitors AC Specifications
Parameter
Description
Response time
Document Number: 001-53304 Rev. *K
Conditions
Page 106 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.5.3 Interrupt Controller
Table 11-68. Interrupt Controller AC Specifications
Parameter
Description
Delay from interrupt signal input to ISR
code execution from ISR code
Conditions
Min
Typ
Max
Units
Includes worse case completion of
longest instruction DIV with 6 cycles
–
–
25
Tcy CPU
Typ
Max
Units
MHz
11.5.4 JTAG Interface
Figure 11-66. JTAG Interface Timing
(1/f_TCK)
TCK
T_TDI_setup
T_TDI_hold
TDI
T_TDO_valid
T_TDO_hold
TDO
T_TMS_setup
T_TMS_hold
TMS
Table 11-69. JTAG Interface AC Specifications[49]
Parameter
f_TCK
Description
TCK frequency
Conditions
Min
3.3 V ≤ VDDD ≤ 5 V
–
–
14[50]
1.71 V ≤ VDDD < 3.3 V
–
–
7[50]
MHz
ns
T_TDI_setup
TDI setup before TCK high
(T/10) – 5
–
–
T_TMS_setup
TMS setup before TCK high
T/4
–
–
T_TDI_hold
TDI, TMS hold after TCK high
T = 1/f_TCK max
T/4
–
–
T_TDO_valid
TCK low to TDO valid
T = 1/f_TCK max
–
–
2T/5
T_TDO_hold
TDO hold after TCK high
T = 1/f_TCK max
T/4
–
–
Notes
49. Based on device characterization (Not production tested).
50. f_TCK must also be no more than 1/3 CPU clock frequency.
Document Number: 001-53304 Rev. *K
Page 107 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.5.5 SWD Interface
Figure 11-67. SWD Interface Timing
(1/f_SWDCK)
SWDCK
T_SWDI_setup T_SWDI_hold
SWDIO
(PSoC 3 reading on SWDIO)
T_SWDO_valid
T_SWDO_hold
SWDIO
(PSoC 3 writing to SWDIO)
Table 11-70. SWD Interface AC Specifications[51]
Parameter
Description
Conditions
Min
Typ
Max
[52]
Units
3.3 V ≤ VDDD ≤ 5 V
–
–
14
MHz
1.71 V ≤ VDDD < 3.3 V
–
–
7[52]
MHz
–
–
5.5[52]
MHz
T_SWDI_setup SWDIO input setup before SWDCK high T = 1/f_SWDCK max
T/4
–
–
–
T_SWDI_hold
T/4
–
–
–
f_SWDCK
SWDCLK frequency
1.71 V ≤ VDDD < 3.3 V,
SWD over USBIO pins
SWDIO input hold after SWDCK high
T = 1/f_SWDCK max
T_SWDO_valid SWDCK high to SWDIO output
T = 1/f_SWDCK max
–
–
2T/5
–
T_SWDO_hold SWDIO output hold after SWDCK low
T = 1/f_SWDCK max
T/4
–
–
–
Min
Typ
Max
Units
–
–
33
Mbit
11.5.6 SWV Interface
Table 11-71. SWV Interface AC Specifications[51]
Parameter
Description
SWV mode SWV bit rate
Conditions
Notes
51. Based on device characterization (Not production tested).
52. ff_SWDCK must also be no more than 1/3 CPU clock frequency.
Document Number: 001-53304 Rev. *K
Page 108 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.6 Clocking
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
11.6.1 32 kHz External Crystal
Table 11-72. 32 kHz External Crystal DC Specifications[53]
Parameter
ICC
Description
Operating current
Conditions
Low-power mode
Min
Typ
Max
Units
–
0.25
1.0
µA
CL
External crystal capacitance
–
6
–
pF
DL
Drive level
–
–
1
µW
Min
Typ
Max
Units
–
32.768
–
kHz
–
1
–
s
Min
Typ
Max
Units
–
–
500
µA
24 MHz – non USB mode
–
–
300
µA
12 MHz
–
–
200
µA
6 MHz
–
–
180
µA
3 MHz
–
–
150
µA
Table 11-73. 32 kHz External Crystal AC Specifications
Parameter
Description
F
Frequency
TON
Startup time
Conditions
High-power mode
11.6.2 Internal Main Oscillator
Table 11-74. IMO DC Specifications
Parameter
Description
Conditions
Supply current
24 MHz – USB mode
With oscillator locking to USB bus
Note
53. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 109 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 11-68. IMO Current vs. Frequency
Table 11-75. IMO AC Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
–4
–
4
%
IMO frequency stability (with factory trim)
24 MHz – Non USB mode
FIMO
24 MHz – USB mode
–0.25
–
0.25
%
12 MHz
–3
–
3
%
6 MHz
–2
–
2
%
3 MHz
–1
–
1
%
–
–
12
µs
F = 24 MHz
–
0.9
–
ns
F = 3 MHz
–
1.6
–
ns
F = 24 MHz
–
0.9
–
ns
F = 3 MHz
–
12
–
ns
Startup
time[54]
With oscillator locking to USB bus
From enable (during normal system
operation) or wakeup from
low-power state
Jitter (peak to peak)[54]
Jp-p
Jitter (long term)
Jperiod
[54]
Figure 11-69. IMO Frequency Variation vs. Temperature
Figure 11-70. IMO Frequency Variation vs. VCC
Note
54. Based on device characterization (Not production tested).
Document Number: 001-53304 Rev. *K
Page 110 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.6.3 Internal Low-Speed Oscillator
Table 11-76. ILO DC Specifications
Parameter
Description
Operating current
Conditions
Min
Typ
Max
Units
FOUT = 1 kHz
–
0.3
1.7
µA
FOUT = 33 kHz
–
1.0
2.6
µA
FOUT = 100 kHz
–
1.0
2.6
µA
Power down mode
–
2.0
15
nA
Min
Typ
Max
Units
–
–
2
ms
100 kHz
45
100
200
kHz
1 kHz
0.5
1
2
kHz
100 kHz
30
100
300
kHz
1 kHz
0.3
1
3.5
kHz
ICC
Leakage current
Table 11-77. ILO AC Specifications
Parameter
Description
Startup time, all frequencies
Conditions
Turbo mode
ILO frequencies (trimmed)
FILO
ILO frequencies (untrimmed)
Figure 11-71. ILO Frequency Variation vs. Temperature
Document Number: 001-53304 Rev. *K
Figure 11-72. ILO Frequency Variation vs. VDD
Page 111 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
11.6.4 External Crystal Oscillator
Table 11-78. ECO AC Specifications
Parameter
F
Description
Conditions
Crystal frequency range
Min
Typ
Max
Units
4
–
25
MHz
Min
Typ
Max
Units
11.6.5 External Clock Reference
Table 11-79. External Clock Reference AC Specifications[55]
Parameter
Description
Conditions
External frequency range
0
–
33
MHz
Input duty cycle range
Measured at VDDIO/2
30
50
70
%
Input edge rate
VIL to VIH
0.1
–
–
V/ns
Min
Typ
Max
Units
–
200
–
µA
Min
Typ
Max
Units
1
–
48
MHz
11.6.6 Phase-Locked Loop
Table 11-80. PLL DC Specifications
Parameter
IDD
Description
PLL operating current
Conditions
In = 3 MHz, Out = 24 MHz
Table 11-81. PLL AC Specifications
Parameter
Fpllin
Description
PLL intermediate
Fpllout
Conditions
PLL input frequency[56]
frequency[57]
1
–
3
MHz
PLL output frequency[56]
24
–
50
MHz
Lock time at startup
–
–
250
µs
–
–
250
ps
Jperiod-rms Jitter (rms)[55]
Output of prescaler
Notes
55. Based on device characterization (Not production tested).
56. This specification is guaranteed by testing the PLL across the specified range using the IMO as the source for the PLL.
57. PLL input divider, Q, must be set so that the input frequency is divided down to the intermediate frequency range. Value for Q ranges from 1 to 16.
Document Number: 001-53304 Rev. *K
Page 112 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
12. Ordering Information
In addition to the features listed in Table 12-1, every CY8C34 device includes: a precision on-chip voltage reference, precision
oscillators, flash, ECC, DMA, a fixed function I2C, 4 KB trace RAM, JTAG/SWD programming and debug, external memory interface,
and more. In addition to these features, the flexible UDBs and analog subsection support a wide range of peripherals. To assist you
in selecting the ideal part, PSoC Creator makes a part recommendation after you choose the components required by your application.
All CY8C34 derivatives incorporate device and flash security in user-selectable security levels; see the TRM for details.
Table 12-1. CY8C34 Family with Single Cycle 8051
I/O[60]
Comparator
SC/CT
Analog Blocks[58]
Opamps
DFB
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
70
62
8
0
100-pin TQFP 0×0E060069
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
46
38
8
0
68-pin QFN
0×0E06E069
CY8C3444LTI-109
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
29
25
4
0
48-pin QFN
0×0E06D069
CY8C3444PVI-118
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
29
25
4
0
48-pin SSOP 0×0E076069
JTAG ID[61]
USBIO
SIO
GPIO
Total I/O
CAN 2.0b
Package
FS USB
16-bit Timer/PWM
DAC
16
50
UDBs[59]
ADC
50
CY8C3444LTI-110
CapSense
LCD Segment Drive
CY8C3444AXI-096
Part Number
CPU Speed (MHz)
EEPROM (KB)
Digital
SRAM (KB)
Analog
Flash (KB)
MCU Core
16 KB Flash
CY8C3444AXI-106
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
72
62
8
2
100-pin TQFP 0×0E06A069
CY8C3444LTI-113
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
48
38
8
2
68-pin QFN
0×0E071069
CY8C3444LTI-112
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
31
25
4
2
48-pin QFN
0×0E070069
CY8C3444PVI-101
50
16
2
0.5
–
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
31
25
4
2
48-pin SSOP 0×0E065069
CY8C3444AXI-116
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
70
62
8
0
100-pin TQFP 0×0E074069
CY8C3444LTI-111
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
46
38
8
0
68-pin QFN
0×0E06F069
CY8C3444LTI-119
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
29
25
4
0
48-pin QFN
0×0E077069
CY8C3444PVI-100
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
–
–
29
25
4
0
48-pin SSOP 0×0E064069
CY8C3444AXI-117
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
72
62
8
2
100-pin TQFP 0×0E075069
CY8C3444LTI-114
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
48
38
8
2
68-pin QFN
0×0E072069
CY8C3444LTI-120
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
31
25
4
2
48-pin QFN
0×0E078069
CY8C3444PVI-103
50
16
2
0.5
✔
12-bit Del-Sig
2
4
2
2
–
✔
16
4
✔
–
31
25
4
2
48-pin SSOP 0×0E067069
32 KB Flash
CY8C3445AXI-104
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
70
62
8
0
100-pin TQFP 0×0E068069
CY8C3445LTI-086
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
46
38
8
0
68-pin QFN
0×0E056069
CY8C3445LTI-093
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
29
25
4
0
48-pin QFN
0×0E05D069
CY8C3445PVI-077
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
29
25
4
0
48-pin SSOP 0×0E04D069
CY8C3445AXI-107
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
72
62
8
2
100-pin TQFP 0×0E06B069
CY8C3445LTI-095
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
48
38
8
2
68-pin QFN
0×0E05F069
CY8C3445LTI-087
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
31
25
4
2
48-pin QFN
0×0E057069
CY8C3445PVI-088
50
32
4
1
–
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
31
25
4
2
48-pin SSOP 0×0E058069
CY8C3445AXI-097
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
70
62
8
0
100-pin TQFP 0×0E061069
CY8C3445LTI-079
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
46
38
8
0
68-pin QFN
0×0E04F069
CY8C3445LTI-078
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
29
25
4
0
48-pin QFN
0×0E04E069
Notes
58. Analog blocks support a wide variety of functionality including TIA, PGA, and mixers. See the Example Peripherals on page 39 for more information on how analog
blocks can be used.
59. UDBs support a wide variety of functionality including SPI, LIN, UART, timer, counter, PWM, PRS, and others. Individual functions may use a fraction of a UDB or
multiple UDBs. Multiple functions can share a single UDB. See the Example Peripherals on page 39 for more information on how UDBs can be used.
60. The I/O Count includes all types of digital I/O: GPIO, SIO, and the two USB I/O. See the I/O System and Routing on page 32 for details on the functionality of each of
these types of I/O.
61. The JTAG ID has three major fields. The most significant nibble (left digit) is the version, followed by a 2 byte part number and a 3 nibble manufacturer ID.
Document Number: 001-53304 Rev. *K
Page 113 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 12-1. CY8C34 Family with Single Cycle 8051 (continued)
I/O[64]
GPIO
SIO
USBIO
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
–
–
29
25
4
0
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
72
62
8
2
100-pin TQFP 0×1E06C069
CY8C3445LTI-081
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
48
38
8
2
68-pin QFN
0×1E051069
CY8C3445LTI-089
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
31
25
4
2
48-pin QFN
0×1E059069
CY8C3445PVI-090
50
32
4
1
✔
12-bit Del-Sig
2
4
2
2
–
✔
20
4
✔
–
31
25
4
2
48-pin SSOP 0×1E05A069
UDBs[63]
4
4
DFB
32
32
Opamps
50
50
DAC
CY8C3445PVI-094
CY8C3445AXI-108
ADC
Total I/O
JTAG ID[65]
CAN 2.0b
Package
FS USB
16-bit Timer/PWM
CapSense
Digital
SC/CT
Analog Blocks[62]
Comparator
LCD Segment Drive
Analog
EEPROM (KB)
SRAM (KB)
Flash (KB)
Part Number
CPU Speed (MHz)
MCU Core
48-pin SSOP 0×1E05E069
64 KB Flash
CY8C3446AXI-115
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
70
62
8
0
100-pin TQFP 0×1E073069
CY8C3446LTI-072
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
46
38
8
0
68-pin QFN
0×1E048069
CY8C3446LTI-071
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
29
25
4
0
48-pin QFN
0×1E047069
CY8C3446PVI-082
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
29
25
4
0
48-pin SSOP 0×1E052069
CY8C3446AXI-098
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
72
62
8
2
100-pin TQFP 0×1E062069
CY8C3446LTI-084
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
48
38
8
2
68-pin QFN
0×1E054069
CY8C3446LTI-073
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
31
25
4
2
48-pin QFN
0×1E049069
CY8C3446PVI-092
50
64
8
2
–
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
31
25
4
2
48-pin SSOP 0×1E05C069
CY8C3446AXI-105
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
70
62
8
0
100-pin TQFP 0×1E069069
CY8C3446LTI-074
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
46
38
8
0
68-pin QFN
0×1E04A069
CY8C3446LTI-083
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
29
25
4
0
48-pin QFN
0×1E053069
48-pin SSOP 0×1E05B069
CY8C3446PVI-091
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
–
29
25
4
0
CY8C3446AXI-099
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
72
62
8
2
100-pin TQFP 0×1E063069
CY8C3446LTI-085
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
48
38
8
2
68-pin QFN
0×1E055069
CY8C3446LTI-075
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
31
25
4
2
48-pin QFN
0×1E04B069
CY8C3446PVI-076
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
✔
–
31
25
4
2
48-pin SSOP 0×1E04C069
CY8C3446PVI-102
50
64
8
2
✔
12-bit Del-Sig
2
4
2
2
–
✔
24
4
–
✔
29
25
4
0
48-pin SSOP 0×1E066069
Notes
62. Analog blocks support a wide variety of functionality including TIA, PGA, and mixers. See the Example Peripherals on page 39 for more information on how analog
blocks can be used.
63. UDBs support a wide variety of functionality including SPI, LIN, UART, timer, counter, PWM, PRS, and others. Individual functions may use a fraction of a UDB or
multiple UDBs. Multiple functions can share a single UDB. See the Example Peripherals on page 39 for more information on how UDBs can be used.
64. The I/O Count includes all types of digital I/O: GPIO, SIO, and the two USB I/O. See the I/O System and Routing on page 32 for details on the functionality of each of
these types of I/O.
65. The JTAG ID has three major fields. The most significant nibble (left digit) is the version, followed by a 2 byte part number and a 3 nibble manufacturer ID.
Document Number: 001-53304 Rev. *K
Page 114 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
12.1 Part Numbering Conventions
PSoC 3 devices follow the part numbering convention described here. All fields are single character alphanumeric (0, 1, 2, …, 9, A,
B, …, Z) unless stated otherwise.
CY8Cabcdefg-xxx
„ a: Architecture
„ ef: Package code
3: PSoC 3
‡ 5: PSoC 5
Two character alphanumeric
AX: TQFP
‡ LT: QFN
‡ PV: SSOP
‡
‡
‡
„ b: Family group within architecture
4: CY8C34 family
6: CY8C36 family
‡ 8: CY8C38 family
‡
„ g: Temperature range
‡
C: commercial
I: industrial
‡ A: automotive
‡
‡
„ c: Speed grade
‡
‡
4: 50 MHz
6: 67 MHz
„ xxx: Peripheral set
‡
„ d: Flash capacity
‡
4: 16 KB
5: 32 KB
‡ 6: 64 KB
‡
Three character numeric
No meaning is associated with these three characters.
‡
Example
CY8C
3 4 4 6 P V
I
-
x x x
Cypress Prefix
3: PSoC 3
4: CY8C34 Family
Architecture
Family Group within Architecture
4: 50 MHz
Speed Grade
6: 64 KB
Flash Capacity
PV: SSOP
Package Code
I: Industrial
Temperature Range
Peripheral Set
All devices in the PSoC 3 CY8C34 family comply to RoHS-6 specifications, demonstrating the commitment by Cypress to lead-free
products. Lead (Pb) is an alloying element in solders that has resulted in environmental concerns due to potential toxicity. Cypress
uses nickel-palladium-gold (NiPdAu) technology for the majority of leadframe-based packages.
A high level review of the Cypress Pb-free position is available on our website. Specific package information is also available. Package
Material Declaration data sheets (PMDDs) identify all substances contained within Cypress packages. PMDDs also confirm the
absence of many banned substances. The information in the PMDDs will help Cypress customers plan for recycling or other “end of
life” requirements.
Document Number: 001-53304 Rev. *K
Page 115 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
13. Packaging
Table 13-1. Package Characteristics
Parameter
Min
Typ
Max
Units
Operating ambient temperature
–40
25.00
85
°C
TJ
Operating junction temperature
–40
–
100
°C
Tja
Package θJA (48-pin SSOP)
–
45.16
–
°C/Watt
Tja
Package θJA (48-pin QFN)
–
15.94
–
°C/Watt
Tja
Package θJA (68-pin QFN)
–
11.72
–
°C/Watt
Tja
Package θJA (100-pin TQFP)
–
30.52
–
°C/Watt
Tjc
Package θJC (48-pin SSOP)
–
27.84
–
°C/Watt
Tjc
Package θJC (48-pin QFN)
–
7.05
–
°C/Watt
Tjc
Package θJC (68-pin QFN)
–
6.32
–
°C/Watt
Tjc
Package θJC (100-pin TQFP)
–
9.04
–
°C/Watt
TA
Description
Conditions
Table 13-2. Solder Reflow Peak Temperature
Package
Maximum Peak
Temperature
Maximum Time at Peak
Temperature
48-pin SSOP
260 °C
30 seconds
48-pin QFN
260 °C
30 seconds
68-pin QFN
260 °C
30 seconds
100-pin TQFP
260 °C
30 seconds
Table 13-3. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-2
Package
MSL
48-pin SSOP
MSL 3
48-pin QFN
MSL 3
68-pin QFN
MSL 3
100-pin TQFP
MSL 3
Document Number: 001-53304 Rev. *K
Page 116 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 13-1. 48-pin (300 mil) SSOP Package Outline
.020
24
1
0.395
0.420
0.292
0.299
25
DIMENSIONS IN INCHES MIN.
MAX.
48
0.620
0.630
0.088
0.092
SEATING PLANE
0.095
0.110
0.005
0.010
.010
GAUGE PLANE
0.004
0.025
BSC
0°-8°
0.008
0.016
0.008
0.0135
0.024
0.040
51-85061-*D
Figure 13-2. 48-pin QFN Package Outline
SIDE VIEW
TOP VIEW
BOTTOM VIEW
1.00 MAX.
7.00±0.10
5.6±0.10
0.05 MAX.
48
37
36
1
PIN 1 ID
0.23±0.05
0.20 REF.
37
48
36
1
PIN 1 DOT
LASER MARK
SOLDERABLE
EXPOSED
PAD
7.00±0.10
5.6±0.10
12
25
13
0.40±0.10
NOTES:
1. HATCH AREA IS SOLDERABLE EXPOSED METAL.
2. REFERENCE JEDEC#: MO-220
3. PACKAGE WEIGHT: 0.13g
4. ALL DIMENSIONS ARE IN MM [MIN/MAX]
5. PACKAGE CODE
PART #
DESCRIPTION
LT48D
LEAD FREE
Document Number: 001-53304 Rev. *K
12
25
24
24
5.55 REF
13
0.50±0.10
0.08
C
5.55 REF
001- 45616 *B
Page 117 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Figure 13-3. 68-pin QFN 8 × 8 with 0.4 mm Pitch Package Outline (Sawn Version)
TOP VIEW
BOTTOM VIEW
SIDE VIEW
0.900±0.100
5.7±0.10
8.000±0.100
0.200 REF
5
1
PIN 1 DOT
8.000±0.100
LASER MARK
1
7
0.20±0.05
3
0.400±0.1005
0.05 MAX
C
0.08
NOTES:
1.
3
4
SEATING PLANE
3
4
1
8
1
SOLDERABLE
EXPOSED
PAD
5.7±0.10
3
5
6
8
5
2
6.40 REF
5
1
1
PIN1 ID
R 0.20
0.400 PITCH
5
2
6
8
HATCH AREA IS SOLDERABLE EXPOSED METAL.
1
8
1
7
6.40 REF
001-09618 *C
2. REFERENCE JEDEC#: MO-220
3. PACKAGE WEIGHT: 0.17g
4. ALL DIMENSIONS ARE IN MILLIMETERS
Figure 13-4. 100-pin TQFP (14 × 14 × 1.4 mm) Package Outline
51-85048 *E
Document Number: 001-53304 Rev. *K
Page 118 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
14. Acronyms
Table 14-1. Acronyms Used in this Document (continued)
Acronym
Table 14-1. Acronyms Used in this Document
Acronym
Description
Description
FIR
finite impulse response, see also IIR
FPB
flash patch and breakpoint
FS
full-speed
GPIO
general-purpose input/output, applies to a PSoC
pin
HVI
high-voltage interrupt, see also LVI, LVD
abus
analog local bus
ADC
analog-to-digital converter
AG
analog global
AHB
AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM data
transfer bus
IC
integrated circuit
ALU
arithmetic logic unit
IDAC
current DAC, see also DAC, VDAC
AMUXBUS
analog multiplexer bus
IDE
integrated development environment
API
application programming interface
APSR
application program status register
ARM®
advanced RISC machine, a CPU architecture
ATM
automatic thump mode
BW
bandwidth
CAN
Controller Area Network, a communications
protocol
CMRR
I
2C,
or IIC
Inter-Integrated Circuit, a communications
protocol
IIR
infinite impulse response, see also FIR
ILO
internal low-speed oscillator, see also IMO
IMO
internal main oscillator, see also ILO
INL
integral nonlinearity, see also DNL
I/O
input/output, see also GPIO, DIO, SIO, USBIO
common-mode rejection ratio
IPOR
initial power-on reset
CPU
central processing unit
IPSR
interrupt program status register
CRC
cyclic redundancy check, an error-checking
protocol
IRQ
interrupt request
DAC
digital-to-analog converter, see also IDAC, VDAC
ITM
instrumentation trace macrocell
DFB
digital filter block
LCD
liquid crystal display
DIO
digital input/output, GPIO with only digital capabilities, no analog. See GPIO.
LIN
Local Interconnect Network, a communications
protocol.
DMA
direct memory access, see also TD
LR
link register
DNL
differential nonlinearity, see also INL
LUT
lookup table
DNU
do not use
LVD
low-voltage detect, see also LVI
DR
port write data registers
LVI
low-voltage interrupt, see also HVI
DSI
digital system interconnect
LVTTL
low-voltage transistor-transistor logic
DWT
data watchpoint and trace
ECC
error correcting code
ECO
external crystal oscillator
EEPROM
electrically erasable programmable read-only
memory
EMI
electromagnetic interference
EMIF
external memory interface
EOC
end of conversion
EOF
end of frame
EPSR
execution program status register
ESD
electrostatic discharge
ETM
embedded trace macrocell
Document Number: 001-53304 Rev. *K
MAC
multiply-accumulate
MCU
microcontroller unit
MISO
master-in slave-out
NC
no connect
NMI
nonmaskable interrupt
NRZ
non-return-to-zero
NVIC
nested vectored interrupt controller
NVL
nonvolatile latch, see also WOL
opamp
operational amplifier
PAL
programmable array logic, see also PLD
PC
program counter
PCB
printed circuit board
PGA
programmable gain amplifier
Page 119 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Table 14-1. Acronyms Used in this Document (continued)
Acronym
Description
Table 14-1. Acronyms Used in this Document (continued)
Acronym
Description
PHUB
peripheral hub
SOF
start of frame
PHY
physical layer
SPI
PICU
port interrupt control unit
Serial Peripheral Interface, a communications
protocol
PLA
programmable logic array
SR
slew rate
PLD
programmable logic device, see also PAL
SRAM
static random access memory
PLL
phase-locked loop
SRES
software reset
PMDD
package material declaration data sheet
POR
power-on reset
PRES
precise power-on reset
PRS
pseudo random sequence
PS
port read data register
PSoC®
Programmable System-on-Chip™
PSRR
power supply rejection ratio
PWM
pulse-width modulator
RAM
random-access memory
RISC
reduced-instruction-set computing
RMS
root-mean-square
RTC
real-time clock
RTL
register transfer language
RTR
remote transmission request
VDAC
voltage DAC, see also DAC, IDAC
RX
receive
WDT
watchdog timer
SAR
successive approximation register
WOL
write once latch, see also NVL
SC/CT
switched capacitor/continuous time
WRES
watchdog timer reset
2C
serial clock
SCL
I
SDA
I2C serial data
S/H
sample and hold
SINAD
signal to noise and distortion ratio
SIO
special input/output, GPIO with advanced
features. See GPIO.
SOC
start of conversion
Document Number: 001-53304 Rev. *K
SWD
serial wire debug, a test protocol
SWV
single-wire viewer
TD
transaction descriptor, see also DMA
THD
total harmonic distortion
TIA
transimpedance amplifier
TRM
technical reference manual
TTL
transistor-transistor logic
TX
transmit
UART
Universal Asynchronous Transmitter Receiver, a
communications protocol
UDB
universal digital block
USB
Universal Serial Bus
USBIO
USB input/output, PSoC pins used to connect to a
USB port
XRES
external reset I/O pin
XTAL
crystal
15. Reference Documents
PSoC® 3, PSoC® 5 Architecture TRM
PSoC® 3 Registers TRM
Page 120 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
16. Document Conventions
16.1 Units of Measure
Table 16-1. Units of Measure
Symbol
Unit of Measure
°C
degrees Celsius
dB
decibels
fF
femtofarads
Hz
hertz
KB
1024 bytes
kbps
kilobits per second
Khr
kilohours
kHz
kilohertz
kΩ
kilohms
ksps
kilosamples per second
LSB
least significant bit
Mbps
megabits per second
MHz
megahertz
MΩ
megaohms
Msps
megasamples per second
µA
microamperes
µF
microfarads
µH
microhenrys
µs
microseconds
µV
microvolts
µW
microwatts
mA
milliamperes
ms
milliseconds
mV
millivolts
nA
nanoamperes
ns
nanoseconds
nV
nanovolts
Ω
ohms
pF
picofarads
ppm
parts per million
ps
picoseconds
s
seconds
sps
samples per second
sqrtHz
square root of hertz
V
volts
Document Number: 001-53304 Rev. *K
Page 121 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
17. Revision History
Description Title: PSoC® 3: CY8C34 Family Data Sheet Programmable System-on-Chip (PSoC®)
Document Number: 001-53304
Submission Orig. of
Rev.
ECN No.
Description of Change
Date
Change
New data sheet
**
2714270
06/03/09
VVSK
*A
2758970
09/02/09
MKEA
Updated Part Numbering Conventions
Added Section 11.7.5 (EMIF Figures and Tables)
Updated GPIO and SIO AC specifications
Updated XRES Pin Description and Xdata Address Map specifications
Updated DFB and Comparator specifications
Updated PHUB features section and RTC in sleep mode
Updated IDAC and VDAC DC and Analog Global specifications
Updated USBIO AC and Delta Sigma ADC specifications
Updated PPOR and Voltage Monitors DC specifications
Updated Drive Mode diagram
Added 48-QFN Information
Updated other electrical specifications
*B
2824546
12/09/09
MKEA
Updated I2C section to reflect 1 Mbps. Updated Table 11-6 and 11- 7 (Boost AC
and DC specs); also added Shottky Diode specs. Changed current for
sleep/hibernate mode to include SIO; Added footnote to analog global specs.
Updated Figures 1-1, 6-2, 7-14, and 8-1. Updated Table 6-2 and Table 6-3
(Hibernate and Sleep rows) and Power Modes section. Updated GPIO and SIO AC
specifications. Updated Gain error in IDAC and VDAC specifications. Updated
description of VDDA spec in Table 11-1 and removed GPIO Clamp Current
parameter. Updated number of UDBs on page 1.
Moved FILO from ILO DC to AC table.
Added PCB Layout and PCB Schematic diagrams.
Updated Fgpioout spec (Table 11-9). Added duty cycle frequency in PLL AC spec
table. Added note for Sleep and Hibernate modes and Active Mode specs in Table
11-2. Linked URL in Section 10.3 to PSoC Creator site.
Updated Ja and Jc values in Table 13-1. Updated Single Sample Mode and Fast
FIR Mode sections. Updated Input Resistance specification in Del-Sig ADC table.
Added Tio_init parameter. Updated PGA and UGB AC Specs. Removed SPC ADC.
Updated Boost Converter section.
Added section 'SIO as Comparator'; updated Hysteresis spec (differential mode)
in Table 11-10.
Updated VBAT condition and deleted Vstart parameter in Table 11-6.
Added 'Bytes' column for Tables 4-1 to 4-5.
*C
2873322
02/04/10
MKEA
Changed maximum value of PPOR_TR to '1'. Updated Vbias specification.
Updated PCB Schematic. Updated Figure 8-1 and Figure 6-3. Updated Interrupt
Vector table, Updated Sales links. Updated JTAG and SWD specifications.
Removed Jp-p and Jperiod from ECO AC Spec table. Added note on sleep timer
in Table 11-2. Updated ILO AC and DC specifications. Added Resolution parameter
in VDAC and IDAC tables. Updated IOUT typical and maximum values. Changed
Temperature Sensor range to –40 °C to +85 °C. Removed Latchup specification
from Table 11-1.
Document Number: 001-53304 Rev. *K
Page 122 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Description Title: PSoC® 3: CY8C34 Family Data Sheet Programmable System-on-Chip (PSoC®)
Document Number: 001-53304
*D
2903576
04/01/10
MKEA
Updated Vb pin in PCB Schematic
Updated Tstartup parameter in AC Specifications table
Added Load regulation and Line regulation parameters to Inductive Boost
Regulator DC Specifications table
Updated ICC parameter in LCD Direct Drive DC Specs table
In page 1, updated internal oscillator range under Precision programmable clocking
to start from 3 MHz
Updated IOUT parameter in LCD Direct Drive DC Specs table
Updated Table 6-2 and Table 6-3
Removed DFB block in Figure 1-1.
Added bullets on CapSense in page 1; added CapSense column in Section 12
Removed some references to footnote [1]
Changed INC_Rn cycles from 3 to 2 (Table 4-1)
Added footnote in PLL AC Specification table
Added PLL intermediate frequency row with footnote in PLL AC Specs table
Added UDBs subsection under 11.6 Digital Peripherals
Updated Figure 2-6 (PCB Layout)
Updated Pin Descriptions section and modified Figures 6-6, 6-8, 6-9
Updated LVD in Tables 6-2 and 6-3; modified Low-power modes bullet in page 1
Added note to Figures 2-5 and 6-2; Updated Figure 6-2 to add capacitors for VDDA
and VDDD pins.
Updated boost converter section (6.2.2)
Updated Tstartup values in Table 11-3.
Removed IPOR rows from Table 11-67.
Updated 6.3.1.1, Power Voltage Level Monitors.
Updated section 5.2 and Table 11-2 to correct suggestion of execution from flash.
Updated IMO max frequency in Figure 6-1, Table 11-77, and Table 11-78.
Updated VREF specs in Table 11-21.
Updated IDAC uncompensated gain error in Table 11-25.
Updated Delay from Interrupt signal input to ISR code execution from ISR code in
Table 11-57. Removed other line in table.
Added sentence to last paragraph of section 6.1.1.3.
Updated TRESP, high and low-power modes, in Table 11-24.
Updated f_TCK values in Table 11-72 and f_SWDCK values in Table 11-73.
Updated SNR condition in Table 11-20.
Updated sleep wakeup time in Table 6-3 and Tsleep in Table 11-3.
Added 1.71 V <= VDDD < 3.3 V, SWD over USBIO pins value to Table 11-73.
Removed mention of hibernate reset (HRES) from page 1 features, Table 6-3,
Section 6.2.1.4, Section 6.3, and Section 6.3.1.1. Change PPOR/PRES to TBDs
in Section 6.3.1.1, Section 6.4.1.6 (changed PPOR to reset), Table 11-3 (changed
PPOR to PRES), Table 11-67 (changed title, values TBD), and Table 11-68
(changed PPOR_TR to PRES_TR).
Added sentence saying that LVD circuits can generate a reset to Section 6.3.1.1.
Changed IDD values on page 1, page 5, and Table 11-2.
Changed resume time value in Section 6.2.1.3.
Changed ESD HBM value in Table 11-1.
Changed sample rate row in Table 11-20. Removed VDDA = 1.65 V rows and
changed BWag value in Table 11-22.
Changed VIOFF values and changed CMRR value in Table 11-23.
Changed INL max value in Table 11-27.
Added max value to the Quiescent current specs in Tables 11-29 and 11-31.
Changed occurrences of “Block” to “Row” and deleted the “ECC not included”
footnote in Table 11-55.
Changed max response time value in Tables 11-68 and 11-70.
Changed the Startup time in Table 11-78.
Added condition to intermediate frequency row in Table 11-84.
Added row to Table 11-68.
Added brown out note to Section 11.8.1.
Document Number: 001-53304 Rev. *K
Page 123 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Description Title: PSoC® 3: CY8C34 Family Data Sheet Programmable System-on-Chip (PSoC®)
Document Number: 001-53304
*E
2938381
05/27/10
MKEA
Replaced VDDIO with VDDD in USBIO diagram and specification tables, added text
in USBIO section of Electrical Specifications.
Added Table 13-2 (Package MSL)
Modified Tstorag condition and changed max spec to 100
Added bullet (Pass) under ALU (section 7.2.2.2)
Added figures for kHzECO and MHzECO in the External Oscillator section
Updated Figure 6-1(Clocking Subsystem diagram)
Removed CPUCLK_DIV in table 5-2, Deleted Clock Divider SFR subsection
Updated PSoC Creator Framework image
Updated SIO DC Specifications (VIH and VIL parameters)
Updated bullets in Clocking System and Clocking Distribution sections
Updated Figure 8-2
Updated PCB Layout and Schematic, updated as per MTRB review comments
Updated Table 6-3 (power changed to current)
In 32kHZ EC DC Specifications table, changed ICC Max to 0.25
In IMO DC Specifications table, updated Supply Current values
Updated GPIO DC Specs table
Modified to support a maximum 50MHz CPU speed
*F
2958674
06/22/10
SHEA
Minor ECN to post data sheet to external website
*G
2989685
08/04/10
MKEA
Added USBIO 22 ohm DP and DM resistors to Simplified Block Diagram
Added to Table 6-6 a footnote and references to same.
Added sentences to the resistive pull-up and pull-down description bullets.
Added sentence to Section 6.4.11, Adjustable Output Level.
Updated section 5.5 External Memory Interface
Updated Table 11-73 JTAG Interface AC Specifications
Updated Table 11-74 SWD Interface AC Specifications
Updated style changes as per new template.
*H
3078568
11/04/10
MKEA
Updated Table 11-2, “DC Specifications,” on page 64
Updated “Current Digital-to-analog Converter (IDAC)” on page 86
Updated “Voltage Digital to Analog Converter (VDAC)” on page 91
*I
3107314 12/10/2010
MKEA
Updated delta-sigma tables and graphs.
Updated Flash AC specs
Formatted table 11.2.
Updated interrupt controller table
Updated transimpedance amplifier section
Updated SIO DC specs table
Updated Voltage Monitors DC Specifications table
Updated LCD Direct Drive DC specs table
Replaced the Discrete Time Mixer and Continuous Time Mixer tables with Mixer
DC and AC specs tables
Updated ESDHBM value.
Updated IDAC and VDAC sections
Removed ESO parts from ordering information
Changed USBIO pins from NC to DNU and removed redundant USBIO pin
description notes
Updated POR with brown out DC and AC specs
Updated PGA AC specs
Updated 32 kHz External Crystal DC Specifications
Updated opamp AC specs
Updated XRES IO specs
Updated Inductive boost regulator section
Delta sigma ADC spec updates
Updated comparator section
Removed buzz mode from Power Mode Transition diagram
Updated opamp DC and AC spec tables
Updated PGA DC table
*J
3179219
02/22/2011
MKEA
Updated conditions for flash data retention time.
Updated 100-pin TQFP package spec.
Updated EEPROM AC specifications.
Document Number: 001-53304 Rev. *K
Page 124 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
Description Title: PSoC® 3: CY8C34 Family Data Sheet Programmable System-on-Chip (PSoC®)
Document Number: 001-53304
*K
3200146
03/28/2011
MKEA
Removed Preliminary status from the data sheet.
Updated JTAG ID
Deleted Cin_G1, ADC input capacitance from Delta-Sigma ADC DC spec table
Updated JTAG Interface AC Specifications and SWD Interface Specifications
tables
Updated USBIO DC specs
Added 0.01 to max speed
Updated Features on page 1
Added Section 5.5, Nonvolatile Latches
Updated Flash AC specs
Added CAN DC specs
Updated delta-sigma graphs, noise histogram figures and RMS Noise spec tables
Add reference to application note AN58304 in section 8.1
Updated 100-pin TQFP package spec
Added oscillator, I/O, VDAC, regulator graphs
Updated JTAG/SWD timing diagrams
Updated GPIO and SIO AC specs
Updated POR with Brown Out AC spec table
Updated IDAC graphs
Added DMA timing diagram, interrupt timing and interrupt vector, I2C timing
diagrams
Updated opamp graphs and PGA graphs
Added full chip performance graphs
Changed MHzECO range.
Added “Solder Reflow Peak Temperature” table.
Document Number: 001-53304 Rev. *K
Page 125 of 126
[+] Feedback
PSoC® 3: CY8C34 Family
Data Sheet
18. Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturers’ representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
PSoC Solutions
Automotive
Clocks & Buffers
Interface
cypress.com/go/automotive
psoc.cypress.com/solutions
cypress.com/go/clocks
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/interface
Lighting & Power Control
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
cypress.com/go/memory
Optical & Image Sensing
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
cypress.com/go/USB
Wireless/RF
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2009-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-53304 Rev. *K
®
®
®
®
Revised March 30, 2011
Page 126 of 126
®
CapSense , PSoC 3, PSoC 5, and PSoC Creator™ are trademarks and PSoC is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced
herein are property of the respective corporations.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips.
ARM is a registered trademark, and Keil, and RealView are trademarks, of ARM Limited. All products and company names mentioned in this document may be the trademarks of their respective holders..
[+] Feedback
Similar pages