BD243, BD243A, BD243B, BD243C NPN SILICON POWER TRANSISTORS ● Designed for Complementary Use with the BD244 Series ● 65 W at 25°C Case Temperature ● 6 A Continuous Collector Current B 1 ● 10 A Peak Collector Current C 2 ● Customer-Specified Selections Available E 3 TO-220 PACKAGE (TOP VIEW) Pin 2 is in electrical contact with the mounting base. MDTRACA absolute maximum ratings at 25°C case temperature (unless otherwise noted) RATING SYMBOL Collector-emitter voltage (RBE = 100 Ω) BD243B Collector-emitter voltage (IC = 30 mA) VCER 115 45 V CEO Peak collector current (see Note 1) Continuous base current Continuous device dissipation at (or below) 25°C case temperature (see Note 2) Continuous device dissipation at (or below) 25°C free air temperature (see Note 3) Unclamped inductive load energy (see Note 4) Operating junction temperature range Storage temperature range Lead temperature 3.2 mm from case for 10 seconds NOTES: 1. 2. 3. 4. 60 80 V V 100 BD243C Continuous collector current 90 BD243C BD243B Emitter-base voltage 70 BD243 BD243A UNIT 55 BD243 BD243A VALUE VEBO 5 IC 6 V A ICM 10 A IB 3 A Ptot 65 W Ptot 2 W ½LIC2 62.5 mJ °C Tj -65 to +150 Tstg -65 to +150 °C TL 250 °C This value applies for tp ≤ 0.3 ms, duty cycle ≤ 10%. Derate linearly to 150°C case temperature at the rate of 0.52 W/°C. Derate linearly to 150°C free air temperature at the rate of 16 mW/°C. This rating is based on the capability of the transistor to operate safely in a circuit of: L = 20 mH, IB(on) = 0.4 A, RBE = 100 Ω, VBE(off) = 0, RS = 0.1 Ω, VCC = 20 V. JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. 1 BD243, BD243A, BD243B, BD243C NPN SILICON POWER TRANSISTORS electrical characteristics at 25°C case temperature PARAMETER V(BR)CEO ICES ICEO IEBO hFE V CE(sat) VBE hfe |hfe | Collector-emitter breakdown voltage TEST CONDITIONS IC = 30 mA MIN IB = 0 (see Note 5) BD243 45 BD243A 60 BD243B 80 BD243C 100 TYP MAX V VCE = 55 V VBE = 0 BD243 0.4 Collector-emitter VCE = 70 V VBE = 0 BD243A 0.4 cut-off current VCE = 90 V VBE = 0 BD243B 0.4 VCE = 115 V VBE = 0 BD243C 0.4 Collector cut-off VCE = 30 V IB = 0 BD243/243A 0.7 current VCE = 60 V IB = 0 BD243B/243C 0.7 VEB = 5V IC = 0 Forward current VCE = 4V IC = 0.3 A transfer ratio VCE = 4V IC = 3A IB = 1A IC = 6A VCE = 4V IC = 6A Emitter cut-off current Collector-emitter saturation voltage Base-emitter voltage Small signal forward current transfer ratio Small signal forward current transfer ratio UNIT mA mA 1 mA (see Notes 5 and 6) 1.5 V (see Notes 5 and 6) 2 V 30 (see Notes 5 and 6) 15 VCE = 10 V IC = 0.5 A f = 1 kHz 20 VCE = 10 V IC = 0.5 A f = 1 MHz 3 NOTES: 5. These parameters must be measured using pulse techniques, tp = 300 µs, duty cycle ≤ 2%. 6. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts. thermal characteristics MAX UNIT RθJC Junction to case thermal resistance PARAMETER MIN TYP 1.92 °C/W RθJA Junction to free air thermal resistance 62.5 °C/W MAX UNIT resistive-load-switching characteristics at 25°C case temperature PARAMETER † TEST CONDITIONS † MIN ton Turn-on time IC = 1 A IB(on) = 0.1 A IB(off) = -0.1 A toff Turn-off time VBE(off) = -3.7 V RL = 20 Ω tp = 20 µs, dc ≤ 2% 0.3 µs 1 µs Voltage and current values shown are nominal; exact values vary slightly with transistor parameters. 2 TYP JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. BD243, BD243A, BD243B, BD243C NPN SILICON POWER TRANSISTORS TYPICAL CHARACTERISTICS TYPICAL DC CURRENT GAIN vs COLLECTOR CURRENT COLLECTOR-EMITTER SATURATION VOLTAGE vs BASE CURRENT TCS633AH hFE - DC Current Gain VCE = 4 V TC = 25°C tp = 300 µs, duty cycle < 2% 100 10 1·0 0·1 1·0 IC = 300 mA IC = 1 A IC = 3 A IC = 6 A 1·0 0·1 0·01 0·001 10 TCS633AE 10 VCE(sat) - Collector-Emitter Saturation Voltage - V 1000 IC - Collector Current - A 0·01 0·1 1·0 10 IB - Base Current - A Figure 1. Figure 2. BASE-EMITTER VOLTAGE vs COLLECTOR CURRENT 1·2 TCS633AF VBE - Base-Emitter Voltage - V VCE = 4 V TC = 25°C 1·1 1·0 0·9 0·8 0·7 0·6 0·1 1·0 10 IC - Collector Current - A Figure 3. JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. 3 BD243, BD243A, BD243B, BD243C NPN SILICON POWER TRANSISTORS MAXIMUM SAFE OPERATING REGIONS MAXIMUM FORWARD-BIAS SAFE OPERATING AREA IC - Collector Current - A 100 SAS633AD tp = 300 µs, d = 0.1 = 10% tp = 1 ms, d = 0.1 = 10% tp = 10 ms, d = 0.1 = 10% DC Operation 10 1·0 0·1 BD243 BD243A BD243B BD243C 0·01 1·0 10 100 1000 VCE - Collector-Emitter Voltage - V Figure 4. THERMAL INFORMATION MAXIMUM POWER DISSIPATION vs CASE TEMPERATURE TIS633AB Ptot - Maximum Power Dissipation - W 80 70 60 50 40 30 20 10 0 0 25 50 75 100 125 150 TC - Case Temperature - °C Figure 5. 4 JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. BD243, BD243A, BD243B, BD243C NPN SILICON POWER TRANSISTORS MECHANICAL DATA TO-220 3-pin plastic flange-mount package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. TO220 4,70 4,20 ø 10,4 10,0 3,96 3,71 1,32 1,23 2,95 2,54 see Note B 6,6 6,0 15,90 14,55 see Note C 6,1 3,5 1,70 1,07 0,97 0,61 1 2 14,1 12,7 3 2,74 2,34 5,28 4,88 VERSION 1 0,64 0,41 2,90 2,40 VERSION 2 ALL LINEAR DIMENSIONS IN MILLIMETERS NOTES: A. The centre pin is in electrical contact with the mounting tab. B. Mounting tab corner profile according to package version. C. Typical fixing hole centre stand off height according to package version. Version 1, 18.0 mm. Version 2, 17.6 mm. JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. MDXXBE 5